The influence of core-shell structured modifiers on the toughness of poly (vinyl chloride)

The core-shell structured grafted copolymer particles of polybutadiene grafted polymethyl methacrylate (PB-g-PMMA, MB) were prepared by emulsion polymerization. The MB particles were used to modify poly (vinyl chloride) (PVC) by melt blending. The mechanical properties of the PVC blends were investigated. The micro-morphology of the PVC blends was observed by scanning electron microscopy (SEM). The results indicated that the samples with the best impact strength could be obtained when the core-shell weight ratio of PB to PMMA is lower than 93:7, the mechanical properties correlated well with SEM morphologies, the addition of modifier with the ratio core to shell of 93:7 could reduce the domain size of the dispersed phase. Furthermore, the compatibility and properties of the blends were greatly enhanced and improved. The modifier particles could be well dispersed in the PVC matrix.     

Influence of lanthanum stearate as a co-stabilizer on stabilization efficiency of calcium/zinc stabilizers to polyvinyl chloride

Influence of lanthanum stearate (LaSt₃) as a co-stabilizer on stabilization efficiency of calcium stearate (Ca)/zinc glutarate (Zn) stabilizers to polyvinyl chloride (PVC) at 180 °C in air was investigated. The results showed that combination of LaSt₃ with Ca/Zn stabilizers presented an obvious improvement of stabilization efficiency to PVC compared with the Ca/Zn stabilizers. Moreover, addition of LaSt₃ to the Ca/Zn stabilizers could significantly enhance static stability time of PVC. Incorporation of 2 phr LaSt₃ co-stabilizer to PVC containing 3 phr Ca/Zn stabilizers resulted in marked increase of onset degradation temperature and reductions in average degradation rate as well as the dynamic storage modulus (G′) and loss modulus (G″) at 180 °C. Influence of Ca/Zn ratio on tensile strength of PVC in the absence or in the presence of LaSt₃ was discussed in detail. At low Ca/Zn ratios LaSt₃ had an obvious improvement in the tensile strength, while at high Ca/Zn ratios this effect became inconspicuous.     

Environmental stress cracking of poly(vinyl chloride) in alkaline solutions

The environmental stress cracking (ESC) effects on PVC of various high pH sodium hydroxide environments have been studied. The behaviour of PVC specimens in air and pH 12, 13, 13.5 and 14.39 sodium hydroxide solutions has been examined under three-point bend, tensile and creep conditions. Two parameters were used in three-point bend testing to determine the effect of an applied strain and high pH environment on the stability of PVC, namely time to craze initiation and width of crazing. It was found that, in general, crazing occurred sooner and to a greater degree with increasing strain and pH, although there was some evidence that craze growth was most rapid at pH 13.5. The results also indicated a critical strain value of 1.5–1.6%, below which crazing was not observed in any of these alkaline environments. Creep and tensile testing revealed that the time for which a PVC specimen was immersed in the environment was very important in determining the severity of the environmental effect. Creep tests at elevated temperatures showed that the time for the effects to be manifest decreased with increasing temperature. Creep rates were highest in pH 13.5 sodium hydroxide solution indicating that this was the most hostile of the environments considered.     

Properties of poly(vinyl chloride)/wood flour/montmorillonite composites: Effects of coupling agents and layered silicate

Organomodified montmorillonite (OMMT) was prepared using cetylalkyl trimethyl amine bromide. OMMT and wood flour (WF) were surface-modified by silane coupling agent. They were melt-blended with polyvinyl chloride (PVC) and extruded into wood-plastic composite samples using one conical twin screw extruder. The effects of their contents on the composite mechanical properties were investigated. X-ray diffraction, transmission electron microscopy and scanning electron microscopy observed intercalation and dispersion of the OMMT. FTIR and X-ray photoelectron spectroscopy were used to analyze the silane-modification effects. The possible reaction mechanisms were proposed. After wood flour was modified by 1.5 phr silane, the impact strength and the tensile strength of wood flour-PVC composite were increased by 14.8% and 18.5%, respectively. Mechanical tests showed that the addition of OMMT did not enhance the untreated wood flour-PVC composites. However, adding 0.5% OMMT did improve the mechanical properties of the treated ones. The grafting improved the interfacial compatibility between components producing higher properties of the composites. Further addition of OMMT reinforced the composites. Too higher contents of silane and OMMT impaired some properties because of weak interfacial layer and higher concentrated stress. Cone calorimetry showed that the fire flame retardancy and smoke suppression of composites were strongly improved with the addition of OMMT.     

溶剂性能对部分解缠结聚氯乙烯有序结构形成的影响

一般的高分子非晶态是线团相互穿透的多链凝聚态,是分子固体中非常独特的一种分子凝聚态[1～4].而高分子链的缠结是高聚物凝聚态的重要特征之一.缠结是指高分子链之间形成物理交联点,构成网络结构,使分子链的运动受到周围分子的羁绊和限制[5],因此缠结对链的构象调整以及链单元     

Influence of lanthanum stearate and calcium/zinc stabilizers on stabilization efficiency of dibutyltin dilaurate to polyvinyl chloride

<正>Influences of lanthanum stearate(LaSt_3) and calcium stearate/zinc stearate(Ca/Zn) stabilizers on stabilization efficiency of dibutyltin dilaurate(DBTDL) to polyvinyl chloride(PVC) in air were investigated.The results revealed that the stabilization effect of DBTDL could be achieved by the La/Sn stabilizers with a ratio of 8/2.Addition of DBTDL could enhance thermal property and reduce dynamic storage modulus(G′) at 180℃for PVC containing LaSt_3 or Ca/Zn stabilizers. On the other hand,incorporation of LaSt_3 did not influence the stabilization efficiency of DBTDL markedly;while addition of Ca/Zn stabilizers could significantly decrease thermal property for the DBTDL stabilized PVC.Furthermore,the effects of LaSt_3 and Ca/Zn stabilizers on the stabilization efficiency of DBTDL were explained in the framework of ionization potential.     

Optimization of the curing conditions of PVC plastisols based on the use of an epoxidized fatty acid ester plasticizer

The use of an epoxidized fatty acid ester (EFAE) as a natural-based plasticizer for plasticized PVC (P-PVC) has been evaluated in this work. The effect of the curing conditions has been studied by following several test techniques such as mechanical properties, thermal behavior, color changes, solvent migration and microstructure. Different curing processes at isothermal conditions (ranging from 160 °C to 220 °C) have been carried at curing times in the 6–16 min range. The optimum mechanical response (tensile strength values in the 9–10 MPa range and elongation at break close to 250%) is obtained for plastisols cured at 200 and 220 °C for 12 and 8 min curing times, respectively. These curing conditions also offer the lowest migration in n-hexane (lower than 11%) which is indicative of plasticizer total absorption. Furthermore, the use of these curing conditions does not lead to thermal degradation as confirmed by color measurements.     

The compatibility of (natural) polyols with heavy metal- and zinc-free poly(vinyl chloride): Their effect on rheology and implications for plate-out

This paper describes the rheological effects observed after addition of (natural) polyols to several different types of heavy metal-free PVC formulations. It is found that addition of natural polyols, such as sorbitol, leads to changes in the rheology of the system comparable to the addition of external lubricants. Hence as suggested previously, addition of (natural) polyols may lead to the occurrence of undesirable plate-out phenomena. The magnitude of the effect on the rheology depends on the number of hydroxyl groups in the polyol and its propensity to undergo intramolecular cyclodehydration reactions. It is established that the undesirable rheological effects, which coincide with plate-out phenomena, can be suppressed by the addition of various types of inorganic as well as organic substances, most of which are known PVC additives. This will allow for the use of (natural) polyols as efficient and benign co-stabilisers in next generation stabiliser systems.     

Comparative non-isothermal kinetic analysis of thermal degradation of poly(vinyl chloride) prepared by living and conventional free radical polymerization methods

Non-isothermal kinetics of the thermal degradation of poly(vinyl chloride) (PVC) prepared by a living radical polymerization (LRP) method was performed and compared with the results obtained from PVC prepared by the conventional free-radical process (FRP). Both differential and integral isoconversional methods were applied for determining the apparent activation energy of the dehydrochlorination stage. This study made clear noticeable differences in the thermal degradation of the PVC samples under analysis. The newly synthesized LRP-PVC material has a better thermal stability and presents substantial differences in the macroscopic kinetics of the dehydrochlorination process compared with conventional FRP-PVC. These differences were assessed in quantitative terms on the basis of the kinetic triplet [E_a,A,f(α)].     

D-异抗坏血酸硬脂酸酯的合成及其性能研究

L-抗坏血酸(VC)高级脂肪酸酯,是一类新型的脂溶性抗氧化剂,被广泛用于油脂、食品、医疗卫生、化妆品等领域。D-异抗坏血酸(即异VC)是L-抗坏血酸的异构体,与L-抗坏血酸相比较,被氧化的速度更快,价格更低,是近年来在国内外得到普遍使用的食品抗氧化剂。但是,由于溶解性的原因,D-异抗坏血酸不能用于动植物油的保鲜。如果也能将高级脂肪酸引入到D-异抗坏血酸分子中生成D-异抗坏血酸高级脂肪酸酯。     

FT‐IR Investigation into the miscible interactions in new materials for optical devices

In this article we determine the miscibility of azobenzene derivative (poly(4‐(N‐(2‐methacryloyloxyethyl)‐N‐ethylamino)‐4′‐nitroazobenzene)₉₀‐co‐(methyl methacrylate)₁₀)/poly(vinyl acetate) (PVAc) and azobenzene derivative/poly(vinyl chloride) (PVC) blends using Fourier Transform infrared (FT‐IR) spectroscopy. With this method we can clearly identify the exact interactions responsible for miscibility. In the azobenzene derivative 50:50PVAc blend new peaks were evident at 2960, 2890, 1237 and 959 cm^?1, these peaks depict miscible interactions. These wavenumbers indicate that the miscible interactions occurring are from the C? H stretching band, the vinyl acetate C?O, conjugated to the ester carbonyl, the cis‐transformation N?N stretch frequency and the acetate ester weak doublet. The azobenzene derivative 80:20PVC blend display peaks identical in profile to the blend homopolymers, indicating no miscible interactions. However, this could be due to overlapping of peaks within the same wavenumber region, making resolution difficult. This research demonstrates FT‐IR can deduce favorable interactions for miscibility and therefore numerous miscible blends can successfully be calculated if possessing the same groups responsible for miscibility. This paves the way for a new generation of designer optical materials with the desired properties. Copyright © 2003 John Wiley & Sons, Ltd.     

Molecular orientation behavior of poly(vinyl chloride) as influenced by the nanoparticles and plasticizer during uniaxial film stretching in the rubbery stage

The structural evolution during uniaxial stretching of poly(vinyl chloride) films was studied using our real time spectral birefringence stretching machine. The effect of clay loading and the amount of plasticizer as well as the rate effects on the birefringence development and true mechanical response are presented with a final model summarizing the molecular phenomena during stretching. Mechano‐optical studies revealed that birefringence correlated with mechanical response (stress, strain, work) nonlinearly. This was primarily attributed to the preexisting strong network of largely amorphous chains connected via small crystallites that act as physical crosslinking points. These crystallites are not easily destroyed during the high‐speed stretching process as evidenced from the birefringence–true strain curves along with the X‐ray crystallinity measurements. At high speeds, the amorphous chains do not have enough time to relax and hence attain higher orientation levels. The crystallites, however, orient more efficiently when stretched at slow speeds. Apparently, some relaxation of the surrounding amorphous chains helps rotate the crystallites in the stretching direction. Overall birefringence is higher at high stretching speeds for a given true strain value. When the nanoparticles are incorporated, the orientation levels are increased significantly for both the crystalline and amorphous phases. Nanoplatelets increase the continuity of the network because they have strong interaction with the amorphous chains and/or crystallites. This in turn helps transfer the local stresses to the attached chains and increase the orientation levels of the chains. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 724–742, 2005     

Development of a Poly(vinyl chloride)-based Nitrate Ion-selective Electrode

The authors developed a nitrate ion-selective electrode(ISE) based on poly(vinyl chloride)(PVC) membrane with methyltrioctylammonium nitrate as a carrier and 1-decanol as a plasticizer. The performance of the nitrate-sensitive membranes was optimized by tuning the composition of components. The electrode exhibits a linear response with a Nernstian slope of (52±1.0) mV per decade for the nitrate ion concentration ranging from 5.8×10^-5 mol/L to 1.0 mol/L. The electrode can be used to detect a low concentration of nitrate ions down to 3×10^-5 mol/L in a pH range of 2.1-11.5 without any compensation. The advantage of the electrode includes simple preparation, short response time and good repeatability. The detection performance of the novel electrode on nitrate ions has been tested for water samples.     

Formation of crystalline inclusion compounds of poly (vinyl chloride) of different stereoregularity with γ-cyclodextrin

This work reports the formation and detailed characterization of the γ-cyclodextrin (γ-CD) inclusion compounds (ICs) formed with two poly (vinyl chloride) samples with different isotactic content. The ICs were characterized by X-ray diffraction, solid state ¹³C-NMR, solution ¹H-NMR, FT-infrared, differential scanning calorimetry, and thermogravimetric analysis. Experimental evidence of the inclusion of the guest polymer chains into the narrow channels created by the γ-CD crystalline host lattice has been obtained. Examination of coalesced poly (vinyl chlorides) (PVCs) obtained after the host γ-CD is removed reveals different characteristics specifically for the coalesced PVC sample with higher isotactic content. An increase in T_g was observed by DSC for this PVC. To the contrary, the T_g of the coalesced PVC sample with lower isotactic content is almost the same as that of the as-synthesized sample. Thermogravimetric analysis indicated that coalesced PVC with higher isotactic content acquires a degree of stabilization after modification by threading into and being extracted from its γ-CD IC. The results suggest that an irreversible conformational change takes place when PVC forms ICs with a solid host lattice like γ-CD. The PVC molecules extend and reorganize into a more stable conformation in the IC, consequently improving the properties of the coalesced sample. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2503–2513, 2007     

Effects of Epoxidation Content of ENR on Morphology and Mechanical Properties of Natural Rubber Blended PVC

This research work has concerned a study on toughness of PVC/natural rubber (NR) blends compatibilized with epoxidized natural rubber (ENR). The aim of this work was to investigate the effect of degree of epoxidation on morphology and mechanical properties of the blends. Epoxidized natural rubber with a variety of epoxidation contents were prepared by reacting the NR latex with formic acid and hydrogen peroxide at various chemical contents. Chemical structure and epoxidation content of epoxidized natural rubber were evaluated by FTIR and ¹H-NMR techniques. After that, three grades of ENR with epoxidation contents of 15, 25 and 42 % (by mole) were further used for blending with PVC and NR in an internal mixer at 60 rpm and at 170 °C. From tensile and impact tests, it was found that tensile elongation and impact strength of the materials remarkably increased with degree of epoxidation. On the other hand, tensile strength and modulus of the materials rarely changed with the epoxidation content. An increase in toughness of the blends with epoxidation content was related to a better molecular interaction between PVC and ENR as suggested by torque-time curves of the materials.     

Ni selective sensors based on meso-tetrakis-{4-[tris-(4-allyl dimethylsilyl-phenyl)-silyl]-phenyl}porphyrin and (sal)2trien in poly(vinyl chloride) matrix

PVC-based membranes of meso-tetrakis-{4-[tris-(4-allyl dimethylsilyl-phenyl)-silyl]-phenyl}porphyrin (I) and (sal)₂trien (II) as electroactive material with dioctylphthalate (DOP), tri-n-butylphosphate (TBP), chloronapthalene (CN), dibutylphthalate (DBP) and dibutyl(butyl) phosphonate (DBBP) as plasticising solvent mediators have been found to act as Ni²⁺ selective sensor. The best performance was obtained with the sensor having a membrane of composition of I: sodium tetraphenyl borate: PVC in the ratio 5:5:150. The sensor exhibits Nernstian response in the activity range 2.5 × 10⁻⁶ to 1.0 × 10⁻¹ M, performs satisfactorily over wide pH range (2–5.5) with a fast response time (8 s). The sensor was found to work satisfactorily in partially non-aqueous media up to 20% (v/v) content of methanol or ethanol and acetone and could be used over a period of 4 months. Potentiometric selectivity coefficients determined by matched potential method (MPM) indicate excellent selectivity for Ni²⁺ ions. The sensors could be used successfully in the estimation of nickel in different brand of chocolates and also as an indicator electrode in potentiometric titration.     

Transition from crazing to shear deformation in ABS/PVC blends

ABS/PVC blends were prepared over a range of compositions by mixing PVC, SAN, and PB‐g‐SAN. All samples were designed to have a constant rubber level of 12 wt % and the ratio of total‐SAN to PVC in the matrix of the blends varied from 70.5/17.5 to 18/80. Transmission electron microscope and scanning electron microscope have been used to study deformation mechanisms in the ABS/PVC blends. Several different types of microscopic deformation mechanisms, depending on the composition of blends, were observed for the ABS/PVC blends. When the blend is a SAN‐rich system, the main deformation mechanisms were crazing of the matrix. When the blend is a PVC‐rich system, crazing could no longer be detected, while shear yielding of the matrix and cavitation of the rubber particles were the main mechanisms of deformation. When the composition of blend is in the intermediate state, both crazing and shear yielding of matrix were observed. This suggests that there is a transition of deformation mechanism in ABS/PVC blends with the change in composition, which is from crazing to shear deformation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 687–695, 2006     

Anthraquinone derivatives as organic stabilizers for rigid poly(vinyl chloride) against photo-degradation

Anthraquinone derivatives have been prepared and investigated as photo-stabilizers for rigid PVC by measuring the extent of weight loss (%), the amount of gel formation as well as the intrinsic viscosity of the soluble fractions of the degraded polymer. The results indicated a reasonable stabilizing effect of these derivatives compared with UV-commercially used stabilizers. A synergistic effect is achieved when the anthraquinone derivatives are mixed with UV-absorbers in a weight ratio of 75% of investigated organic stabilizer and 25% of reference stabilizer.A probable radical mechanism is proposed to account for the stabilizing action of the organic investigated materials.     

Synthesis of a bio-based plasticizer from oleic acid and its evaluation in PVC formulations

The bio-based plasticizers have been extensively developed due to their high compatibility and low toxicity. In this study, the bio-based plasticizers of methyl 10-(2-methoxy-2-oxoethansulfonyl) octadecanoate (MDA) and ethyl 10-(2-ethoxy-2-oxoethanesulfonyl) octadecanoate (EDA) were synthesized from the oleic acid and thioglycolic acid and characterized by ¹HNMR and FT-IR. The prepared materials were applied as plasticizers in Poly(vinyl chloride) (PVC) and their properties were compared with the commercial plasticizer, Bis(2-ethylhexyl) phthalate (DOP). The viscosities of prepared plastisols from novel designed plasticizers were lower than DOP. The results of mechanical properties showed that the synthesized plasticizers of MDA and EDA have the ability of plasticizing effects similar to DOP on PVC. Thermogravimetric analysis (TGA) indicated that both MDA and EDA have higher thermal stability than DOP. Two polar ester as well as polar sulfone groups in the chemical structure of MDA and EDA led to lower migration, volatility and exudation than DOP.     

Poly(vinyl chloride) on the way from the 19th century to the 21st century

Despite all the technical and economic problems and the public discussions on the environmental dangers and hazards of chlorine chemistry, poly(vinyl chloride) (PVC) is the second most produced plastic (with a worldwide capacity of about 31 million tons), placing after polyolefins and before styrene polymers. Presently, PVC production worldwide is growing at a rate of more than 4% per year. The application of PVC was first described in a patent in 1913, but only after 1930 did a sustained interest in PVC arise in several industrial laboratories. The most remarkable milestones in PVC history and their importance to the development of macromolecular chemistry are briefly described, and some present PVC research and industrial applications, with respect to polymerization, stabilization, bulk property modification, and chemical and material recycling of PVC waste, are discussed. Some actual selected topics include the emulsion polymerization of vinyl chloride with polymeric surfactants and controlled free-radical polymerization with nitroxyls, whereas ionic and metal organic initiators have not found any technical applications. Chemical reactions offer many possibilities for the modification of PVC, but they have been not used on a technical scale yet. Much work has been done on stabilization with nontoxic or metal-free systems. The bulk properties of PVC can be influenced by impact modification through the addition of graft copolymers or by blending with other polymers. Also presented are some problems and recent developments in PVC recycling. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 578–586, 2004