In vitro and in vivo degradation behaviors of thermosensitive poly(organophosphazene) hydrogels

Biodegradable and thermosensitive poly(organophosphazenes) with various substituents were synthesized and their hydrolytic degradation properties were investigated in vitro and in vivo. The aqueous solutions of all polymers showed a sol-gel phase transition behavior depending on temperature changes. The side groups of polymers significantly affected the polymer degradation and accelerated hydrolysis of polymers in the order of carboxylic acid > depsipeptide > without carboxylic acid and depsipeptide. The increased gel strength led to the decreased hydrolysis rate. The polymer hydrogels with 750 Da of α-amino-ω-methoxy poly(ethylene glycol) were rapidly decreased by dissolution. The polymer degradation was also influenced by pH and temperature. The in vivo behaviors of mass decrease of the polymer hydrogels were similar with the in vitro results. These results suggest that the biodegradable and thermosensitive poly(organophosphazenes) hold great potentials as an injectable and biodegradable hydrogel for biomedical applications with controllable degradation rate.     

Stability of a salicylate-based poly(anhydride-ester) to electron beam and gamma radiation

The effect of electron beam and gamma radiation on the physicochemical properties of a salicylate-based poly(anhydride-ester) was studied by exposing polymers to 0 (control), 25 and 50 kGy. After radiation exposure, salicylic acid release in vitro was monitored to assess any changes in drug release profiles. Molecular weight, glass transition temperature and decomposition temperature were evaluated for polymer chain scission and/or crosslinking as well as changes in thermal properties. Proton nuclear magnetic resonance and infrared spectroscopies were also used to determine polymer degradation and/or chain scission. In vitro cell studies were performed to identify cytocompatibility following radiation exposure. These studies demonstrate that the physicochemical properties of the polymer are not substantially affected by exposure to electron beam and gamma radiation.     

Degradation studies on segmented polyurethanes prepared with poly (d, l-lactic acid) diol, hexamethylene diisocyanate and different chain extenders

In order to investigate the effect of different chain extenders on degradation properties of segmented polyurethanes (SPUs), three types of segmented polyurethanes (SPU-P, SPU-O and SPU-A) based on poly (d, l-lactic acid) diol, hexamethylene diisocyanate (HDI), were synthesized with three chain extenders: peperazine (PP), 1, 4-butanediol (BDO) and 1, 4-butanediamine (BDA), respectively. Thermogravimetric analysis, activation energy and in vitro degradation were used to characterize the obtained polymers, quantitatively. The results revealed that chain extender played an important role in thermal degradation and biodegradation of polyurethanes. Thermogravimetric analysis and activation energy demonstrated that SPU-O, SPU-P and SPU-A presented best, second and weakest thermostability, respectively, and the thermal degradation mechanism of three SPUs was the same and regarded as a two-stage degradation. Data of hydrolytic degradation of the polymers during 12 weeks indicated that the in vitro degradation stability of SPU-A and SPU-P was similar, but both were better than that of SPU-O. The reason for the differences among three types of SPUs was discussed in this paper.     

Crystallization behavior, thermal property and biodegradation of poly(3-hydroxybutyrate)/poly(ethylene glycol) grafting copolymer

The poly(3-hydroxybutyrate)(PHB)/poly(ethylene glycol)(PEG) grafting copolymer was successfully prepared by PHB and acrylate groups ended PEGM using AIBN as initiator. The crystallization behavior, thermal stability and environmental biodegradability of PHB/PEG grafting copolymers were investigated with differential scanning calorimetry (DSC), Thermogravimetric analysis (TGA), wide angle X-ray diffraction (WAXD), scanning electron microscopy (SEM), and Biodegradation test in vitro. In the results, all the grafting copolymers were found to show the X-ray diffraction arising from the PHB crystal lattice, while none of the PEG crystallized peaks could be found even though the graft percent reached 20%. This result indicated that PEG molecules were randomly grafted onto PHB chain. The thermal properties measured by DSC showed that the melting temperature(T_m) and glass transition temperature (T_g) were both shifted to lower temperature with the graft percent increasing, and this broadened the narrow processability window of PHB. According to TGA results, the thermal stability of the grafting copolymers is not changed compared to pure PHB. From the biodegradation test, it could be concluded that degradation occurred gradually from the surface to the inside and that the degradation rate could be adjusted by the PEG grafting ratio. In another words, the biodegradation profiles of PHB/PEG grafting copolymer can be controlled. These properties make PHB/PEG grafting copolymer have promising potential applications especially in agriculture fields.     

Functional Polymers. X. Hydrolysis Studies of Polyesters and Polycarbonates of Bithionol and Their Copolymers

The hydrolysis behavior of a number of polymers of bithionol [2,2′-thiobis(4,6-dichlorphenol)] was investigated. The hydrolysis of polyesters of bithionol with aliphatic or aromatic dicarboxylic acids or phosphorus acids as well as polycarbonates and alternating copolycarbonates and polyurethanes or co(po1y-carbonates/polyurethanes) depends primarily on the water solubility of the polymer or at least on its degree of swelling. In the most favorable case of the alternating bithionol/PEG 4000 co-polycarbonate the hydrolysis rate of the polymer at 37°C was 1.62 L/mol/min at pH 10, 0.63 L/mol/min at pH 4 and 0.17 L/mol/min at pH 7.4. Copolycarbonates and copolyurethanes with PEG 4000 in the polymer chain have slightly lower rates of hydrolysis. When the solubility of the polymer is low and the crystallinity     

Biodegradable polyphosphazenes for drug delivery

Polyphosphazene derivatives having amino acid ester side groups were prepared by reaction of poly(dichlorophosphazene) with ethyl esters of amino acids. The in vitro degradation studies demonstrated that the rate of degradation depends on the nature of the amino acids. Introducing small amounts of hydrolytically sensitive groups such as depsipeptide ester or hydrolysis-catalysing moieties, such as histidine ethyl ester co-substituents, resulted in an increase of the degradation. The rate of hydrolytic degradation of the polyphosphazene material could be controlled by the content of the hydrolytically sensitive side groups or by blending hydrolysis-sensitive polymers with more stable derivatives. The results obtained from the in vivo implantation of biodegradable polyphosphazenes in mice indicate that the materials are very well tolerated by the animal body. Biodegradable polyphosphazenes have been used as matrix for the design of drug delivery systems. The rate of the in vitro release of mitomycin C from biodegradable polyphosphazenes can be controlled by changing the chemical composition of the polymer or by blending polymers of different chemical compositions.     

Biodegradable photocrosslinkable poly(depsipeptide‐co‐ε‐caprolactone) for tissue engineering: Synthesis,characterization, and In vitro evaluation

Stereolithography has become increasingly popular in scaffold fabrication due to automation and well‐controlled geometry complexity, and consequently, there is a great need for new suitable biodegradable photocrosslinkable polymers. In this study, a new type of photocrosslinkable poly(ester amide) was synthesized based on ε‐caprolactone and l ‐alanine‐derived depsipeptide and was applied to fabrication of three‐dimensional (3D) scaffolds by stereolithography. ¹H nuclear magnetic resonance and Fourier transform infra‐red analysis confirmed the formation of new bonds during the polymer synthesis. Incorporation of depsipeptide increased the glass transition temperature and hydrophilicity of the polymer and accelerated hydrolytic degradation compared with the poly(ε‐caprolactone) homopolymer. The compressive strength of the 3D scaffolds increased with the increasing depsipeptide content. This work demonstrated that incorporation of depsipeptide into photocrosslinkable polyesters resulted in excellent cytocompatibility and tunable degradation rates and mechanical properties and thus expanded the repertoire of biomaterials suitable for 3D photofabrication of high‐resolution tissue engineering scaffolds. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3307–3315     

Degradation of poly(ethylene oxide) by high-speed stirring

Degradation of poly(ethylene oxide) (PEO) by violent stirring was studied in various solvents. The chain scission or the limit of the degradation was measured, and the effects of solvents, polymer concentration, stirring speed and degree of polymerization (DP) were investigated. It was found that the number of bonds broken per polymer chain was independent of the concentration but increased with the stirring speed and with decrease in the DP. The rate was much affected by the solvent used, being larger in a poor solvent. It was also found that the rate could be represented either by Jellinek's or Ovenall's rate equations, which have been applied to the ultrasonic degradation of polymers in solution.     

Microbial aspects of the degradation of water-soluble synthetic polymers

This paper focuses on microbial aspects of degradation of synthetic polymers, especially of water-soluble specialty polymers. The polymer structures analogous to natural polymers suggest biodegradability which originates from enzymes which do not discriminate between natural and synthetic polymers. Hydrolysis and oxidation are the primary processes for biodegradation. Assimilation rates are determined by the conversion of the polymer carbons into common metabolic products whether degradation is exogenous or endogenous. Biochemical mechanisms in the degradation of polyethers are summarized. Microbial symbiosis was involved in the degradation of a copolymer and the availability of symbiotic processes is suggested for the degradation of all copolymers. Transportability of PEG 20 000 through cell walls was suggested and a chemical process using hydrogen peroxide and ferric ions is proposed for the depolymerization of PEG with Mn more than 20 000 and its copolymers.     

Elastic/adhesive double-layered PLA-PEG multiblock copolymer membranes for postoperative adhesion prevention

Tissue adhesions cause severe and life-threatening conditions, including pain, infertility, and heart defects. The purpose of this study is to develop an anti-adhesion membrane that sticks onto the injured tissues or organs in order to avoid the suturing of the membrane which may lead to the unnecessary tissue adhesion. We previously developed poly(lactic acid)-poly(ethylene glycol) (PLA-PEG) multiblock copolymers as soft, water absorbable, and quickly degradable biomaterials. The copolymer with the highest PEG content adsorbs body fluid in vivo and sticks to the tissues. In the present study thin film and nanofiber mat were prepared from the copolymer and evaluated in vitro and in vivo. The hydrophilicity and the degradation rate increased with the increased PEG content of the multiblock copolymers. The copolymer with PEG content of 88% (LE(m)-88) was quickly swollen, become viscous, and rapidly collapsed in PBS, which was suitable feature for adhesion prevention material without suturing. Various double layered membranes with different characteristics were evaluated in vivo by applying onto the cecum scrubbed with abrasive paper, and onto the heart surface after pericardium removal. LE(m)-88 was swollen with tissue fluid and had a hydrogel-like nature. LE(m)-88 film/LE(m)-32 film double layered membrane was found to be the most effective in preventing tissue adhesion in cecum model. This excellent performance was confirmed in the rat heart adhesion model. In both models, the LE(m)-32 support film was detached from the site of application, which leads to the healing without adhesion.     

Effect of gamma radiation on dilute aqueous solutions and thin films of N-succinyl chitosan

N-Succinyl chitosan (N-SC) products with various degrees of substitution were synthesized by a direct reaction between chitosan and succinic anhydride. The susceptibility of the as-synthesized polymers to degradation upon their exposure to γ-ray radiation was investigated. The results were compared with the as-received chitosan. The size exclusion chromatographic results showed that chitosan and N-SC products in their dilute aqueous solution state were more subservient to degradation by γ-ray radiation than in their solid film state, despite the much less exposure to the radiation (i.e., 5-30 kGy for the solutions versus 20-100 kGy for the films). Increasing the radiation dose resulted in the rather monotonous decrease in the molecular weights of the polymers. Structural analyses of the irradiated polymers by Fourier-transformed infrared spectroscopy (FT-IR) and UV-visible spectrophotometry indicated the increase in the amount of carbonyl groups with the radiation dose. The formation of the carbonyl groups suggested that the radiolysis of chitosan and N-SC products occurred at the glycosidic linkages. In addition, FT-IR, elemental analysis and proton nuclear magnetic resonance spectroscopy (¹H NMR) results suggested that γ-ray radiation affected both the N-acetyl and N-substituted groups on the polymer chains.     

Degradation kinetics of poly(lactic-co-glycolic) acid block copolymer cast films in phosphate buffer solution as revealed by infrared and Raman spectroscopies

Poly(lactic-co-glycolic) acid (PLGA) is an important copolymer used in drug delivery platforms where controlled release is required. In this work we investigated the in vitro degradation of four PLGA copolymers with L/G molar compositions of 50/50, 65/35, 75/25 and 95/5. ATR-IR and Raman spectroscopies were used to differentiate and quantify the degradation rates of glycolic and lactic units. Both techniques were used to determine the polymer composition as a function of degradation time and the degradation rate constants for the hydrolysis of glycolic and lactic units were calculated using a 1st order kinetics approach. Our results revealed a two stage process for the degradation of PLGA cast films in PBS in agreement with our previous work. The degradation rate constant for glycolic unit was found to be 1.3 times higher than for lactic units. In addition the degradation rate constants for L and G units were shown to decrease proportionally with increasing initial lactic content of the copolymer used to prepare the films.     

Thermal degradation kinetics of thermoresponsive poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) copolymers prepared via RAFT polymerization

Reversible addition-fragmentation chain transfer polymerization at 70 °C in N,N-dimethylformamide was used to prepare poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) copolymers in various compositions to afford well-defined polymers with pre-determined molecular weight, narrow molecular weight distribution, and precise chain end structure. The copolymer compositions were determined by ¹H NMR spectroscopy. The reactivity ratios of N-isopropylacrylamide (NIPAM) and N,N-dimethylacrylamide (DMA) were calculated as r _NIPAM = 0.838 and r _DMA = 1.105, respectively, by the extended Kelen–Tüdös method at high conversions. The lower critical solution temperature of PNIPAM can be altered by changing the DMA content in the copolymer chain. Differential scanning calorimetry and thermogravimetric analysis at different heating rates were carried out on these copolymers to understand the nature of thermal degradation and to determine its kinetics. Different kinetic models were applied to estimate various parameters like the activation energy, the order, and the frequency factor. These studies are important to understand the solid state polymer degradation of N-alkyl substituted polymers, which show great potential in the preparation of miscible polymer blends due to their ability to interact through hydrogen bonding.     

Degradation of poly(ethylene terephthalate)/clay nanocomposites during melt extrusion: Effect of clay catalysis and chain extension

Organoclays with various contents of hydroxyl groups and absorbed ammonium were prepared and compounded with poly(ethylene terephthalate) (PET), forming PET/clay nanocomposites via melt extrusion. Dilute solution viscosity techniques were used to evaluate the level of molecular weight of PET/clay nanocomposites. Actually, a significant reduction in PET molecular weight was observed. The level of degradation depended on both the clay structure and surfactant chemistry in organoclays. The composites, based on clay with larger amount of hydroxyl groups on the edge of clay platelets, experienced much more degradation, because the hydroxyl groups acted as Brønsted acidic sites to accelerate polymer degradation. Furthermore, organoclays with different amounts of absorbed ammonium led to different extents of polymer degradation, depending upon the acidic sites produced by the Hofmann elimination reaction of ammonium. In addition, the composite with better clay dispersion state, which was considered as an increasing amount of clay surface and ammonium exposed to the PET matrix, experienced polymer degradation more seriously. To compensate for polymer degradation during melt extrusion, pyromellitic dianhydride (PMDA) was used as chain extender to increase the intrinsic viscosity of polymer matrix; more importantly, the addition of PMDA had little influence on the clay exfoliation state in PET/clay nanocomposites.     

Multiscale analysis of water uptake and erosion in biodegradable polyarylates

The role of hydration in degradation and erosion of materials, especially biomaterials used in scaffolds and implants, was investigated by studying the distribution of water at length scales from 0.1 nm to 0.1 mm using Raman spectroscopy, small-angle neutron scattering (SANS), Raman confocal imaging, and scanning electron microscopy (SEM). The measurements were demonstrated using l-tyrosine derived polyarylates. Bound- and free- water were characterized using their respective signatures in the Raman spectra. In the presence of deuterium oxide (D₂O), H-D exchange occurred at the amide carbonyl but was not detected at the ester carbonyl. Water appeared to be present in the polymer even in regions where there was little evidence for NH to ND exchange. SANS showed that water is not uniformly dispersed in the polymer matrix. The distribution of water can be described as mass fractals in polymers with low water content (∼5 wt%), and surface fractals in polymers with larger water content (15-60 wt%). These fluctuations in the density of water distribution are presumed to be the precursors of the ∼20 μm water pockets seen by Raman confocal imaging, and also give rise to the 10-50 μm porous network seen in SEM. The surfaces of these polymers appeared to resist erosion while the core of the films continued to erode to form a porous structure. This could be due to differences in either the density of the polymer or the solvent environment in the bulk vs. the surface, or a combination of these two factors. There was no correlation between the rate of degradation and the amount of water uptake in these polymers, and this suggests that it is the bound water and not the total amount of water that contributes to hydrolytic degradation.     

Synthesis, characterization and in vitro degradation study of a novel and rapidly degradable elastomer

Biodegradable elastomers represent a useful class of biomaterials. In this paper, a novel biodegradable elastomer, poly(PEG-co-CA) (PEC), was synthesized by condensation of poly(ethylene glycol) (PEG) and citric acid (CA) under atmospheric pressure without any catalyst. We first synthesized a pre-polymer by carrying out a controlled condensation reaction between PEG and citric acid, and then post-polymerised and simultaneously cross-linked the pre-polymer in the mould at 120 °C. The pre-polymer was characterized by FT-IR, ¹H NMR, ¹³C NMR, GPC and DSC. A series of polymers were prepared at different post-polymerisation time and different monomer ratios. Measurements on the mechanical properties of PEC testified that the new polymers are elastomers with low hardness and big elongation, and hydrolytic degradation of the polymer films in a buffer of pH 7.4 at 37 °C showed that PEC had excellent degradability (all the films show the weight losses more than 60% after 96 h incubation). The different post-polymerisation time and monomer ratio had strong influence on the degradation rates and mechanical performances. The material is expected to be useful for controlled drug delivery and other biomedical applications.     

Thermal stability and degradation behavior of novel wholly aromatic azopolyamide-hydrazides

Thermal stability and degradation behavior of a series of novel wholly aromatic polyamide-hydrazides containing azo groups in their main chains have been investigated in nitrogen and in air atmospheres using differential scanning calorimetry (DSC), thermogravimetry (TG), infrared spectroscopy (IR) and elemental analysis. The influences of controlled structural variations and molecular weight on the thermal stability and degradation behavior of this series of polymers have also been studied. The structural differences were achieved by varying the content of para- and meta-substituted phenylene rings incorporated within this series. Azopolyamide-hydrazides having different molecular weights of all para-substituted phenylene type units were also examined. The polymers were prepared by a low temperature solution polycondensation reaction of p-aminosalicylic acid hydrazide [PASH] and an equimolar amount of 4,4′-azodibenzoyl chloride [4,4′ADBC] or 3,3′-azodibenzoyl chloride [3,3′ADBC] or mixtures of various molar ratios of 4,4′ADBC and 3,3′ADBC in anhydrous N,N-dimethyl acetamide [DMAc] containing lithium chloride as a solvent at −10 °C. All the polymers have the same structural formula except the mode of linking phenylene units in the polymer chain. The results clearly reveal that these polymers are characterized by high thermal stability. Their weight loss occurred in three distinctive steps. The first was small and assigned to the evaporation of absorbed moisture. The second was appreciable and was attributed to the cyclodehydration reaction of the hydrazide groups into 1,3,4-oxadiazole rings by losing water, combined with elimination of azo groups by losing molecular nitrogen. This is not a true degradation but rather a thermo-chemical transformation reaction of the azopolyamide-hydrazides into the corresponding polyamide-1,3,4-oxadiazoles. The third was relatively severe and sharp, particularly in air, and corresponded to the decomposition of the resulting polyamide-1,3,4-oxadizoles. In both degradation atmospheres, the improved resistance to high temperatures was always associated with increased content of para-phenylene moieties of the investigated polymer. The better thermal stability of the wholly para-oriented type of polymer relative to the other polymers is attributed to its greater chain symmetry which is responsible for its greater close packing, rod-like structure and consequently stronger intermolecular bonds which would be more difficult to break and therefore more resistance to high temperatures. Further, with exception of 160-200 °C temperature range, where the lower molecular weight samples showed considerable weight losses which were most probably due to hydrogen bonded DMAc, all the wholly para-oriented phenylene type of polymer samples behaved similarly regardless of their respective molecular weight. This seems to indicate that the structural building units responsible for high thermal stability of the polymers are their characteristic groups, such as aromatic moieties, amide and hydrazide linkages in case of azopolyamide-hydrazides, and 1,3,4-oxadiazole rings, aromatic nuclei and amide linking bonds in case of polyamide-1,3,4-oxadiazoles, rather than the longer chain segments.     

A new model for the kinetic analysis of thermal degradation of polymers driven by random scission

In this paper, a series of f(α) kinetic equations able to describe the random scission degradation of polymers is formulated in such a way that the reaction rate of the thermal degradation of polymers that go through a random scission mechanism can be directly related to the reacted fraction. The proposed equations are validated by a study of the thermal degradation of poly(butylene terephthalate) (PBT). The combined kinetic analysis of thermal degradation curves of this polymer obtained under different thermal pathways have shown that the proposed equation fits all these curves while other conventional models used in literature do not.     

Synthesis, characterization and protein adsorption behaviors of PLGA/PEG di-block co-polymer blend films

A series of poly(D,L-lactic-co-glycolic acid) (PLGA)/poly(ethyleneglycol) (PEG) di-block copolymers were synthesized by ring-opening polymerization of D,L-lactide and glycolide with different molecular weights of monomethoxy polyethyleneglycol (mPEG) 750, 2000 and 5000 as an initiator. The bulk properties of these co-polymers were characterized by using 1H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry (DSC). Electron spectroscopy for chemical analysis (ESCA) results, in which the blend films with the di-block copolymers showed increasing surface oxygen atomic percentage with increasing PEG chain length, indicate that PEG chain segment in the di-block copolymers is surface oriented and enriched onto the surface of the blend films. The extent of protein adsorption onto the surface of these blend films was studied, using iodine radio-labeled human serum albumin, gamma globulin and human growth hormone. The protein adsorption amount was reduced for the blend films prepared with PLGA/PEG 750 and 2000 di-block copolymers, but increased to a great extent for PLGA/PEG 5000 di-block copolymer. This is due to the increased water uptake capacity of the blend film, which absorbed more protein molecules into a swollen polymer matrix in addition to surface adsorption.     

Hydrolytic degradation of carbohydrate-based aromatic homo- and co-polyesters analogous to PET and PEI

The hydrolytic degradation of a series of homo- and co-polyesters analogous to poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI), prepared from carbohydrate-based monomers, was studied. The degradation process was carried out at temperatures of approximately 10 °C above the T_g of the polymers. All the studied polyesters were found to degrade at significant rates, and degradability showed a clear dependence on the configuration of the sugar units present in the polymer chain. No weight loss was detected upon degradation, apparently due to the non-solubility of the degraded products in the aqueous incubation medium. Hydrolysis of co-polyesters took place preferentially by cleavage of the ester groups of the sugar units.