Dithienosilole–phenylquinoxaline‐based copolymers with A‐D‐A‐D and A‐D structures for polymer solar cells

Two copolymers having D‐A‐D‐A ( P1 ) and D‐A ( P2 ) structures with quinoxaline acceptor unit and dithienosilole donor unit were synthesized and their optical and electrochemical (both experimental and theoretical) properties were investigated. The optical properties showed that these copolymers P1 and P2 exhibit optical bandgaps of 1.54 and 1.62 eV, respectively, with broader absorption profiles extending up to 800 nm and 770 nm, respectively. The electrochemical investigation of these two copolymers indicates that they exhibit suitable highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels for efficient exciton dissociation and high open circuit voltage in the resultant polymer solar cells (PSCs). These copolymers were used as donors along with the PC₇₁BM as acceptor for the fabrication of solution processed bulk heterojunction PSCs. The optimized P1 :PC₇₁BM and P2 :PC₇₁BM active layers treated with solvent vapor treatment showed overall power conversion efficiency (PCE) of 7.16% and 6.57%, respectively. The higher PCE of P1 ‐based device as compared to P2 might be attributed to higher crystallinity of P1 and good hole mobility resulting more balanced charge transport. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 376–386     

Synthesis and investigation of photovoltaic properties for polymer semiconductors based on porphyrin compounds as light-harvesting units

We reported on two polymer semiconducting copolymers based on porphyrin compounds, poly[9,9-dioctylfluorene-co-5,15-bis(hexoxybenzyl)-10,20-bis(benzo-4-yl)porphyrin] (PFPor) and poly[9-(heptadecan-9-yl)carbazole-co-5,15-bis(hexoxybenzyl)-10,20-bis(benzo-4-yl)porphyrin] (PCPor), for use as organic photovoltaic materials. The thermal, optical, electrochemical, and photovoltaic properties of the two polymers were investigated. In addition, PC₆₁BM and PC₇₁BM were introduced as acceptor materials to confirm the acceptor effect in bulk heterojunction photovoltaic devices. Moreover, in order to establish acceptor effects, morphologies of polymer/PCBM blend films were analyzed through atomic force microscopy (AFM). PFPor and PCPor exhibited the best device performance with power conversion efficiencies (PCE) of 0.62% and 0.76%, respectively, upon the introduction of PC₇₁BM as the acceptor in the device where 86 wt.% of the PC₇₁BM was contained in the active layer (pol:PC₇₁BM = 1:6, w/w).     

Broad Bandgap D–A Copolymer Based on Bithiazole Acceptor Unit for Application in High‐Performance Polymer Solar Cells with Lower Fullerene Content

A new broad bandgap and 2D‐conjugated D‐A copolymer, PBDTBTz‐T , based on bithienyl‐benzodithiophene donor unit and bithiazole (BTz) acceptor unit, is designed and synthesized for the application as donor material in polymer solar cells (PSCs). The polymer possesses highly coplanar and crystalline structure with a higher hole mobility and lower HOMO energy level which is beneficial to achieve higher open circuit voltage (V_oc) of the PSCs with the polymer as donor. The PSCs based on PBDTBTz‐T :PC₇₁BM blend film with a lower PC₇₁BM content of 40% demonstrate a power conversion efficiency (PCE) of 6.09% with a relatively higher V_oc of 0.92 V. These results indicate that the lower HOMO energy level of the BTz‐based D–A copolymer is beneficial to a high V_oc of the PSCs. The polymer, with highly coplanar and crystalline structure, can effectively reduce the content of fullerene acceptor in the active layer and can enhance the absorption and PCE of the PSCs.

     

Impact of A–D–A-Structured Dithienosilole- and Phenoxazine-Based Small Molecular Material for Bulk Heterojunction and Dopant-Free Perovskite Solar Cells

Herein, the synthesis of the novel acceptor–donor–acceptor (A–D–A)-structured small molecule Si-PO-2CN based on dithienosilole (DTS) as building block flanked by electron-rich phenoxazine (POZ) units, which are terminated with dicyanovinylene, is presented. Si-PO-2CN showed unique electrochemical and photophysical properties and has been successfully employed in perovskite solar cells (PSCs) as well as in bulk heterojunction organic solar cells (OSCs). The PSCs fabricated with dopant-free Si-PO-2CN as hole-transport material (HTM) exhibited a power conversion efficiency (PCE) of 14.1 % (active area=1.02 cm²). Additionally, a PCE of 5.6 % has been achieved for OSCs, which employed Si-PO-2CN as p-type donor material when blended with a [6,6]-phenyl C71 butyric acid methyl ester (PC₇₁BM) acceptor. The versatile application of Si-PO-2CN provides a pathway for further implementation of DTS-based building blocks in solar cells for designing new molecules.     

Effect of Fluorination on the Photovoltaic Properties of Medium Bandgap Polymers for Polymer Solar Cells

Fluorination of conjugated polymers is one of the effective strategies to tune the molecular energy levels and morphology for high efficient polymer solar cells (PSCs). Herein, two novel donor‐acceptor conjugated polymers, PffBT and PBT, based on bis(3,5‐bis(hexyloxy)phenyl)benzo[1,2‐ b:4,5‐b']dithiophene and benzo[c][1,2,5]thiadiazole (BT) with or without fluorination, respectively, were synthesized, and their photovoltaic properties were compared. The polymer PffBT based on fluorinated BT showed lower frontier energy levels, improved polymer ordering, and a well‐developed fibril structure in the blend with PC₇₁BM. As a result, the PSCs based on PffBT/PC₇₁BM exhibit a superior power conversion efficiency (PCE) of 8.6% versus 4.4% for PBT‐based devices, due to a high space charge limit current (SCLC) hole mobility, mixed orientation of polymer crystals in the active layer, and low bimolecular recombination.     

Reduced‐bandgap triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene copolymers pending benzothiadiazole or diketopyrrolopyrrole units for efficient polymer solar cells

Two new side‐chain donor–acceptor (D‐A)‐based triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene (TPA‐alt‐BDT) copolymers ( P1 and P2 ) with pendant benzothiadiazole (BT)/diketopyrrolopyrrole (DPP) in TPA unit were synthesized by Stille coupling polymerization. Their thermal, photophysical, electrochemical, blend film morphology and photovoltaic properties were investigated. Efficient bulk heterojunction polymer solar cells (PSCs) were obtained by solution process using both copolymers as donor materials and PC₇₁BM as acceptor. The maximum power conversion efficiency (PCE) of 3.17% with a highest open‐circuit voltage (V_oc) of 0.86V was observed in the P1 ‐based PSCs, while the maximum short‐circuit current (J_sc) of 10.77 mA cm^?2 was exhibited in the P2 ‐based PSCs under the illumination of AM 1.5, 100 mW cm^?2. The alternating binary donor units and pending acceptor groups played a significant role in tuning photovoltaic properties for this class of the side‐chain D–A‐based copolymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4103–4110     

Silole‐containing polymers for high‐efficiency polymer solar cells

Silole‐containing conjugated polymers ( P1 and P2 ) carrying methyl and octyl substituents, respectively, on the silicon atom were synthesized by Suzuki polycondensation. They show strong absorption in the region of 300–700 nm with a band gap of about 1.9 eV. The two silole‐containing conjugated polymers were used to fabricate polymer solar cells by blending with PC₆₁BM and PC₇₁BM as the active layer. The best performance of photovoltaic devices based on P1 /PC₇₁BM active layer exhibited power conversion efficiency (PCE) of 2.72%, whereas that of the photovoltaic cells fabricated with P2 /PC₇₁BM exhibited PCE of 5.08%. 1,8‐Diiodooctane was used as an additive to adjust the morphology of the active layer during the device optimization. PCE of devices based on P2 /PC₇₁BM was further improved to 6.05% when a TiO_x layer was used as a hole‐blocking layer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Tailorable PC71BM Isomers: Using the Most Prevalent Electron Acceptor to Obtain High‐Performance Polymer Solar Cells

Despite being widely used as electron acceptor in polymer solar cells, commercially available PC₇₁BM (phenyl‐C₇₁‐butyric acid methyl ester) usually has a “random” composition of mixed regioisomers or stereoisomers. Here PC₇₁BM has been isolated into three typical isomers, α‐, β₁‐ and β₂‐PC₇₁BM, to establish the isomer‐dependent photovoltaic performance on changing the ternary composition of α‐, β₁‐ and β₂‐PC₇₁BM. Mixing the isomers in a ratio of α/β₁/β₂=8:1:1 resulted in the best power conversion efficiency (PCE) of 7.67 % for the polymer solar cells with PTB7:PC₇₁BM as photoactive layer (PTB7=poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]]). The three typical PC₇₁BM isomers, even though sharing similar LUMO energy levels and light absorption, render starkly different photovoltaic performances with average‐performing PCE of 1.28–7.44 % due to diverse self‐aggregation of individual or mixed PC₇₁BM isomers in the otherwise same polymer solar cells.     

New alternating D–A1–D–A2 copolymer containing two electron‐deficient moieties based on benzothiadiazole and 9‐(2‐Octyldodecyl)‐8H‐pyrrolo[3,4‐b]bisthieno[2,3‐f:3',2'‐h]quinoxaline‐8,10(9H)‐dione for efficient polymer solar cells

A novel D–A₁–D–A₂ copolymer denoted as P1 containing two electron withdrawing units based on benzothiadiazole (BT) and 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3′,2′‐h]quinoxaline‐8,10(9H)–dione (PTQD) units was synthesized and characterized. The resulting copolymer exhibits a broad‐absorption spectrum, relatively deep lying HOMO energy level (?5.44 eV) and narrow optical bandgap (1.50 eV). Bulk heterojunction (BHJ) polymer solar cells (PSCs) based on P1 as donor and PC₇₁BM as acceptor with optimized donor to acceptor weight ratio of 1:2 and processed with DIO/CB solvent showed good photovoltaic performance with power conversion efficiency of 6.21% which is higher than that of the device processed without solvent additive (4.40%). The absorption and morphology investigations of the active layers indicated that structural and morphological changes were induced by the solvent additive. This higher power conversion efficiency could be mainly attributed to the absorption enhancement and improved charge transported in the active layer induced by the better nanoscale morphology of the active layer. This study demonstrated that a copolymer with two different acceptor moieties in the backbone may be promising candidate as donor copolymer for solution processed BHJ PSCs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 155–168     

Enhanced Performance of Organic Photovoltaic Cells Fabricated with a Methyl Thiophene‐3‐Carboxylate‐Containing Alternating Conjugated Copolymer

A new donor‐acceptor copolymer, containing benzodithiophene (BDT) and methyl thiophene‐3‐carboxylate (3MT) units, is designed and synthesized for polymer solar cells (PSCs). The 3MT unit is used as an electron acceptor unit in this copolymer to provide a lower highest occupied molecular orbital (HOMO) level for obtaining polymer solar cells with a higher open‐circuit voltage (V_OC). The resulting bulk heterojunction PSC made of the copolymer and [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM) exhibits a power conversion efficiency (PCE) up to 4.52%, a short circuit current (J_SC) of 10.5 mA·cm‐², and a V_OC of 0.86 V.     

Significance of miscibility in multidonor bulk heterojunction solar cells

Ternary organic blends have potential in realizing efficient bulk heterojunction (BHJ) organic solar cells by harvesting a larger portion of the solar spectrum than binary blends. Several challenging requirements, based on the electronic structure of the components of the ternary blend and their nanoscale morphology, need to be met in order to achieve high power conversion efficiency in ternary BHJs. The properties of a model ternary system comprising two donor polymers, poly(3-hexylthiophene) (P3HT) and a furan-containing, diketopyrrolopyrrole-thiophene low-bandgap polymer (PDPP2FT), with a fullerene acceptor, PC₆₁BM, were examined. The relative miscibility of PC₆₁BM with P3HT and PDPP2FT was examined using diffusion with dynamic secondary ion mass spectrometry (dynamic SIMS) measurements. Grazing incidence small and wide angle X-ray scattering analysis (GISAXS and GIWAXS) were used to study the morphology of the ternary blends. These measurements, along with optoelectronic characterization of ternary blend solar cells, indicate that the miscibility of the fullerene acceptor and donor polymers is a critical factor in the performance in a ternary cell. A guideline that the miscibility of the fullerene in the two polymers should be matched is proposed and further substantiated by examination of known well-performing ternary blends. The ternary blending of semiconducting components can improve the power conversion efficiency of bulk heterojunction organic photovoltaics. The blending of P3HT and PDPP2FT with PC₆₁BM leads to good absorptive coverage of the incident solar spectrum and cascading transport energy levels. The performance of this ternary blend reveals the impact of the miscibility of PC₆₁BM in each polymer as a function of composition, highlighting an important factor for optimization of ternary BHJs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 237–246     

Solution‐Processed Titanium Chelate Used as Both Electrode Modification Layer and Intermediate Layer for Efficient Inverted Tandem Polymer Solar Cells

Organic polymer solar cells (PSCs) have attracted increasing attention due to light weight, low cost, flexibility and roll‐to‐roll manufacturing. However, the limited light harvest range of the photoactive layer greatly restrains the power conversion efficiency (PCE) enhancement. In order to expand the light absorption range and further enhance the PCE of the PSCs, tandem structures have been designed and demonstrated. In tandem solar cell, the intermediate layer (IML) plays a critical role in physically and electrically connection of the two subcells. Herein, we apply titanium (diisopropoxide) bis(2,4‐pentanedionate) (TIPD) as both electrode modification layer and intermediate layer to investigate the feasibility in inverted tandem polymer solar cells. The same photoactive layers of PTB7‐Th:PC₇₁BM are adopted in both front and rear subcells to simplify the evaluation of effectiveness of TIPD layer in tandem structures. By modulating the treatment condition of IML and the thickness of photoactive layer, efficient inverted tandem PSCs have been achieved with minimized voltage loss and excellent charge transportation, giving a best V_oc of 1.54 V, which is almost two times that of the single bulk heterojunction (BHJ)‐PSC (0.78 V) and an enhanced PCE up to 8.11%.     

Enhanced efficiency of ternary organic solar cells by doping a polymer material in P3HT:PC61BM

Doping a low‐bandgap polymer material (PDTBDT‐DTNT) as a complementary electron donor in poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyricacid methyl ester (PC₆₁BM) blend is experimented to improve the power conversion efficiency (PCE) of organic solar cells (OSCs). The PCE of OSCs was increased from 3.19% to 3.75% by doping 10 wt% PDTBDT‐DTNT, which was 17.55% higher than that of the OSCs based on binary blend of P3HT:PC₆₁BM (host cells). The short‐circuit current density (J_sc) was increased to 10.11 mA·cm⁻² compared with the host cells. Although the PCE improvement could partly be attributed to more photon harvest for complementary absorption of 2 donors by doping appropriate PDTBDT‐DTNT, the promotion of charge separation and transport as well as the suppression of charge recombination due to a matrix of cascade energy levels is also important. And the better morphology of the active layer films is beneficial to the optimized performance of ternary devices.     

Effect of side‐chain positions on morphology and photovoltaic properties of phenazine‐based donor–acceptor copolymers

Two phenazine donor–acceptor‐conjugated copolymers (P1 and P2) with the same polymer backbone but different anchoring positions of alkoxy chain on the phenazine unit were investigated to identify the effect of changing the position of alkoxy chains on their optical, electrochemical, blend film morphology, and photovoltaic properties. Although the optical absorption and frontier orbital energy levels were insensitive to the position of alkoxy chains, the film morphologies and photovoltaic performances changed significantly. P1/PC₇₁BM blend film showed the formation of phase separation with large coarse aggregates, whereas P2/PC₇₁BM blend film was homogeneous and smooth. Accordingly, power conversion efficiency (PCE) of photovoltaic devices increased from 1.50% for P1 to 2.54% for P2. In addition, the PCE of the polymer solar cell based on P2/PC₇₁BM blend film could be further improved to 3.49% by using solvent vapor annealing treatment. These results clearly revealed that tuning the side‐chain position could be an effective way to adjust the morphology of the active layer and the efficiency of the photovoltaic device. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2910–2918     

Ternary Blend Strategy for Achieving High-Efficiency Organic Photovoltaic Devices for Indoor Applications

Monomeric perylene diimide (PDI) small molecules display a high absorption coefficient and crystallinity in solid-state thin films due to strong π–π interactions between the molecules. To take advantage of these exciting properties of PDIs, N,N'-bis(1-ethylpropyl)perylene-3,4,9,10-tetracarboxylic diimide (EP-PDI) was mixed with a binary blend of PTB7 and PC₇₁BM to fabricate an efficient ternary blend, which were in turn used to produce organic photovoltaic (OPV) devices well suited to indoor applications (PTB7=poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl}), PC₇₁BM=[6,6]-phenyl-C₇₁-butyric acid methyl ester). We varied the PC₇₁BM/EP-PDI weight ratio to investigate the influence of EP-PDI on the optical, electrical, and morphological properties of the PTB7:PC₇₁BM:EP-PDI ternary blend. Compared with the reference PTB7:PC₇₁BM binary blend, the ternary blends showed strong optical absorption in the wavelength range in which the spectra of indoor LED lamps show their strongest peaks. The addition of EP-PDI to the binary blend was found to play an important role in altering the morphology of the blend in such a way as to facilitate charge transport in the resulting ternary blend. Apparently, as a result, the optimal PTB7:PC₇₁BM:EP-PDI-based inverted OPV device exhibited a power conversion efficiency (PCE) of 15.68 %, a fill factor (FF) of 68.5 %, and short-circuit current density (J_SC) of 56.7 μA cm⁻² under 500 lx (ca. 0.17 mW cm⁻²) indoor LED light conditions.     

A New D–A conjugated polymer P(PTQD‐BDT) with PTQD acceptor and BDT donor units for BHJ polymer solar cells application

A novel donor–acceptor ( D–A ) copolymer comprising of weak electron donating BDT moiety and strong 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3',2'‐h] quinoxaline‐8,10(9H)‐dione (PTQD) unit denoted as P(PTQD‐BDT) was synthesized as donor material for polymer solar cells. P(PTQD‐BDT) shows a broad visible‐near‐infrared absorption band with an optical bandgap of 1.74 eV and possesses a relatively low‐lying HOMO level at ?5.28 eV. Bulk‐heterojunction polymer solar cell with the optimized blend of 1:2 (weight ratio) P(PTQD‐BDT):PC₇₁BM (processed with chloroform) shows an open circuit voltage of 0.92 V, a short circuit current density of 7.84 mA/cm², and a fill factor of 0.50, achieving a power conversion efficiency (PCE) of 3.61%. The PCE has been further improved to 5.55 % (J_sc = 10.34 mA/cm², V_oc = 0.88V and FF = 0.61), when 3% v ol 1,8‐diio‐dooctane (DIO) was used as solvent additive for the processing of P(PTQD‐BDT):PC₇₁BM blended film. The enhancement in J_sc is as a result of the appropriate morphology and efficient exciton dissociation into free charge carrier. The increase in PCE has been attributed to the favorable nanoscale morphology for efficient exciton dissociation and charge transport (reduction in the electron to hole mobility ratio). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2390–2398     

Aqueous solution-processed NiOx anode buffer layers applicable for polymer solar cells

A green and facile method has been developed for the room temperature and aqueous solution preparation of NiO_x film as anode buffer layers for polymer solar cells (PSCs). The NiO_x buffer layer is prepared simply by spin-coating nickel acetylacetonate precursor-based aqueous solution onto ITO substrate at room temperature in air. UV-ozone post-treatment promotes the formation of dipolar NiOOH species on the film surface, resulting in the anode buffer layer with suitable work function. PSCs have been fabricated with the device structure of ITO/NiO_x/photoactive layer/PFN/Al. The power conversion efficiencies of the PSCs based on PTB7:PC₇₁BM blends (8.43%) and P3HT:PC₇₁BM blends (3.04%) with NiO_x anode buffer layer are comparable to those with the commonly used PEDOT:PSS anode buffer layer. In addition, the devices made with NiO_x buffer layer exhibit much better air stability than those with PEDOT:PSS. These results indicate that the water solution processed NiO_x film at room temperature in air is a promising anode buffer layer for efficient and stable PSCs. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 747–753     

Planar Conjugated Polymers Containing 9,10‐Disubstituted Phenanthrene Units for Efficient Polymer Solar Cells

Four novel conjugated polymers ( P1‐4 ) with 9,10‐disubstituted phenanthrene (PhA) as the donor unit and 5,6‐bis(octyloxy)benzothiadiazole as the acceptor unit are synthesized and characterized. These polymers are of medium bandgaps (2.0 eV), low‐lying HOMO energy levels (below −5.3 eV), and high hole mobilities (in the range of 3.6 × 10⁻³ to 0.02 cm² V⁻¹ s⁻¹). Bulk heterojunction (BHJ) polymer solar cells (PSCs) with P1‐4 :PC₇₁BM blends as the active layer and an alcohol‐soluble fullerene derivative (FN‐C60) as the interfacial layer between the active layer and cathode give the best power conversion efficiency (PCE) of 4.24%, indicating that 9,10‐disubstituted PhA are potential donor materials for high‐efficiency BHJ PSCs.

     

Donor–acceptor photovoltaic polymers based on 1,4‐dithienyl‐2,5‐dialkoxybenzene with intramolecular noncovalent interactions

Donor–acceptor (D–A) conjugated polymers bearing non‐covalent configurationally locked backbones have a high potential to be good photovoltaic materials. Since 1,4‐dithienyl‐2,5‐dialkoxybenzene ( TBT ) is a typical moiety possessing intramolecular S…O interactions and thus a restricted planar configuration, it was used in this work as an electron‐donating unit to combine with the following electron‐accepting units: 3‐fluorothieno[3,4‐b]thiophene ( TFT ), thieno‐[3,4‐c]pyrrole‐4,6‐dione ( TPD ), and diketopyrrolopyrrole ( DPP ) for the construction of such D–A conjugated polymers. Therefore, the so‐designed three polymers, PTBTTFT , PTBTTPD , and PTBTDPP , were synthesized and investigated on their basic optoelectronic properties in detail. Moreover, using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as acceptor material, polymer solar cells (PSCs) were fabricated for studying photovoltaic performances of these polymers. It was found that the optimized PTBTTPD cell gave the best performance with a power conversion efficiency (PCE) of 4.49%, while that of PTBTTFT displayed the poorest one (PCE = 1.96%). The good photovoltaic behaviors of PTBTTPD come from its lowest‐lying energy level of the highest occupied molecular orbital (HOMO) among the three polymers, and good hole mobility and favorable morphology for its PC₇₁BM‐blended film. Although PTBTDPP displayed the widest absorption spectrum, the largest hole mobility, and regular chain packing structure when blended with PC₇₁BM, its unmatched HOMO energy level and disfavored blend film morphology finally limited its solar cell performance to a moderate level (PCE: 3.91%). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 689–698     

Synthesis of phenanthro[1,10,9,8‐cdefg]carbazole‐based conjugated polymers for organic solar cell applications

Low bandgap polymers with dithienylquinoxaline moieties based on 6H‐phenanthro[1,10,9,8‐cdefg]carbazole were synthesized via the Suzuki coupling reaction. Alkoxy groups were substituted at two different positions on the phenyl groups of the quinoxaline units of these polymers: in the para‐position (PPQP) and in the meta‐position (PPQM). The two polymers showed similar physical properties: broad absorption in the range of 400–700 nm, optical bandgaps of ～1.8 eV, and the appropriate frontier orbital energy levels for efficient charge transfer/separation at polymer/PC₇₁BM interfaces. However, the PPQM solar cell achieved a higher PCE due to its higher J_sc. Our investigation of the morphologies of the polymer:PC₇₁BM blend films and theoretical calculations of the molecular conformations of the polymer chains showed that the polymer with the meta‐positioned alkoxy group has better miscibility with PC₇₁BM than the polymer with the para‐positioned alkoxy group because the dihedral angle of its phenyl group with respect to the quinoxaline unit is higher. This higher miscibility resulted in a polymer:PC₇₁BM blend film with a better morphology and thus in a higher PCE. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 796–803