The SERS response of semiordered Ag nanorod arrays fabricated by template oblique angle deposition

Semiordered Ag nanorod arrays are fabricated by template oblique angle deposition (OAD) using regular Au nano‐post arrays with different diameters as seed patterns. The Au nano‐post arrays do not give an observable surface‐enhanced Raman scattering (SERS) activity under our detection configuration, whereas the patterned Ag nanorod arrays can produce a very strong SERS signal. These SERS intensities increase monotonically with the decrease in the diameter and separation of the Ag nanorods, which demonstrates that one can improve the SERS detection by tuning the diameter and separation of the Ag nanorods, and the template OAD method can help produce more uniform, reproducible, and sensitive Ag nanorod SERS substrates. Copyright © 2010 John Wiley & Sons, Ltd.     

Controlled growth of standing Ag nanorod arrays on bare Si substrate using glancing angle deposition for self-cleaning applications

A facile approach to manipulate the hydrophobicity of surface by controlled growth of standing Ag nanorod arrays is presented. Instead of following the complicated conventional method of the template-assisted growth, the morphology or particularly average diameter and number density (nanorods cm^?2) of nanorods were controlled on bare Si substrate by simply varying the deposition rate during glancing angle deposition. The contact angle measurements showed that the evolution of Ag nanorods reduces the surface energy and makes an increment in the apparent water contact angle compared to the plain Ag thin film. The contact angle was found to increase for the Ag nanorod samples grown at lower deposition rates. Interestingly, the morphology of the nanorod arrays grown at very low deposition rate (1.2 Å?sec^?1) results in a self-cleaning superhydrophobic surface of contact angle about 157° and a small roll-off angle about 5°. The observed improvement in hydrophobicity with change in the morphology of nanorod arrays is explained as the effect of reduction in solid fraction within the framework of Cassie–Baxter model. These self-cleaning Ag nanorod arrays could have a significant impact in wide range of applications such as anti-icing coatings, sensors and solar panels.     

Site‐specific deposition of Ag nanoparticles on ZnO nanorod arrays via galvanic reduction and their SERS applications

A controllable heterostructure consisting of ZnO nanorod arrays with attached Ag nanoparticles at only one end has been synthesized via a facile and convenient galvanic reduction method. Scanning electron microscopic images of these nanostructures showed good selectivity of Ag deposition on the tip of ZnO nanorod arrays. The formation of these regular Ag ZnO heterogeneous nanorod arrays can be explained by a localization of the electrons at the ends of the ZnO nanorods after the electron transfer step. By tuning the reaction time and the concentration of silver nitrate, the density of Ag nanoparticles on the tip of ZnO nanorods can be well controlled. Owing to the introduction of Ag nanoparticles with different densities, the resulting Ag ZnO heterogeneous nanorod arrays have been proved to be a versatile substrate for surface‐enhanced Raman scattering not only for common organic molecules but also for label‐free protein detection. Copyright © 2009 John Wiley & Sons, Ltd.     

Controllable synthesis of Ag nanorods using a porous anodic aluminum oxide template

This paper describes a new approach to the synthesis of Ag nanorods. A solvothermal method was used to make Ag nanoparticles inside anodic aluminum oxide (AAO) templates. The nanoparticles were then annealed at 300 °C to produce Ag nanorods. The size of AAO templates, which is focused on in this study, would determine the diameter of Ag nanorods. The product was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In this study, a nanorod growth mechanism is deduced, and understanding of the growth of nanorods inside AAO templates is furthered. This work demonstrates that it is possible to make crystalline nanorods that the size can be varied.     

Efficient one-pot synthesis of Ag nanoparticles loaded on N-doped multiphase TiO2 hollow nanorod arrays with enhanced photocatalytic activity

The simultaneous Ag loaded and N-doped TiO₂ hollow nanorod arrays with various contents of silver (Ag/N-THNAs) were successfully synthesized on glass substrates by one-pot liquid phase deposition (LPD) method using ZnO nanorod arrays as template. The catalysts were characterized by Raman spectrum, field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscope (HRTEM), ultraviolet-vis (UV-vis) absorption spectrum and X-ray photoelectron spectroscopy (XPS). The results suggest that AgNO₃ additive in the precursor solutions not only can promote the anatase-to-rutile phase transition, but also influence the amount of N doping in the samples. The photocatalytic activity of all the samples was evaluated by photodegradation of methylene blue (MB) in aqueous solution. The sample exhibited the highest photocatalytic activity under UV light illumination when the AgNO₃ concentration in the precursor solution was 0.03 M, due to Ag nanoparticles acting as electron sinks; When the AgNO₃ concentration was 0.07 M, the sample performed best under visible light illumination, attributed to the synergetic effects of Ag loading, N doping, and the multiphase structure (anatase/rutile).     

A template-free sol-gel technique for controlled growth of ZnO nanorod arrays

The growth of ZnO nanorod arrays via a template-free sol-gel process was investigated. The nanorod is single-crystalline wurtzite structure with [0 0 0 1] growth direction determined by the transmission electron microscope. The aligned ZnO arrays were obtained directly on the glass substrates by adjusting the temperatures and the withdrawal speeds, without seed-layer or template assistant. A thicker oriented ZnO nanorod arrays was obtained at proper experimental conditions by adding dip-coating layers. Room temperature photoluminescence spectrum exhibits an intensive UV emission with a weak broad green emission as well as a blue double-peak emission located at 451 and 468 nm, respectively. Further investigation results show that the difference in the alignment of nanorods ascribes to the different orientations of the nanoparticles-packed film formed prior to nanorods on the substrate. Well ordered ZnO nanorods are formed from this film with good c-axis orientation. Our study is expected to pave a way for direct growth of oriented nanorods by low-cost solution approaches.     

两步法制备空间取向高度一致的ZnO纳米棒阵列

采用两步法,即先用磁控溅射在Si(100)表面生长一层ZnO籽晶层、再利用液相法制备空间取向高度一致的ZnO纳米棒阵列.用扫描电子显微镜、X射线衍射、高分辨透射电子显微镜和选区电子衍射对样品形貌和结构特征进行了表征.结果表明,ZnO纳米棒具有垂直于衬底沿c轴择优生长和空间取向高度一致的特性和比较大的长径比,X射线衍射的(XRD)(0002)峰半高宽只有0.06°,选区电子衍射也显示了优异的单晶特性.光致发光谱表明ZnO纳米棒具有非常强的紫外本征发光和非常弱的杂质或缺陷发光特性. 关键词： ZnO纳米棒阵列 ZnO籽晶层 两步法 液相生长     

Aligned CuO nanorod arrays: fabrication and anisotropic ferromagnetism

Copper oxide (CuO) is a p-type semiconductor with a band gap of 1.2 eV, which is well known in high-temperature superconductor and antiferromagnetic (AFM) materials through Cu–O–Cu super-exchange interaction. In this paper, we report the strong anisotropic ferromagnetism (FM) in aligned CuO nanorod arrays synthesized by a microwave-assisted hydrothermal method. The transmission electron microscopy (TEM) image shows that the CuO nanorod consists of a large number of smaller nanorods with almost the same growth direction. The X-ray diffraction (XRD) pattern indicates that the CuO nanorods are well crystallized with highly preferred orientation of the [020] direction. These CuO nanorod arrays show room-temperature ferromagnetism, with strong magnetic anisotropy when the magnetic field is applied perpendicular or parallel to the rod axis. This phenomenon of room-temperature ferromagnetism in those aligned CuO nanorods might originate from uncompensated surface spins and shape anisotropy of the nanorods.     

Enhancement of ethanol sensing of TeO2 nanorods by Ag functionalization

Gas sensors based on Ag–TeO₂ composite nanorods were fabricated using thermal evaporation and sputtering techniques. The morphology, structure and phase composition of the as-prepared nanofibers were characterized by scanning electron microscopy, transmission electron microscopy (TEM), and X-ray diffraction (XRD), respectively. TEM and XRD showed that the nanorods and nanoparticles on them were tetragonal-structured single crystal TeO₂ and a mainly amorphous phase, respectively. The multiple-networked bare TeO₂ nanorod sensors exhibited a response of ～219% at 25 ppm C₂H₅OH at 300 °C, whereas the Ag-functionalized TeO₂ nanorod sensors showed a response of ～808% under the same conditions. The mechanism by which the sensing properties of the TeO₂ nanorods were enhanced by functionalization with Ag is also discussed.     

Controlled synthesis of oriented ZnO nanorod arrays by seed-layer-free electrochemical deposition

Oriented ZnO nanorod arrays were successfully prepared on transparent conductive substrates by seed-layer-free electrochemical deposition in solution of Zn(NO₃)₂ at a low temperature of 70 °C without using any catalysts, additives, and additional seed crystals. The effects of the Zn(NO₃)₂ concentration, deposition time and applied current on the localized nanorod arrays are investigated. X-ray powder diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) were used to characterize the structures and the morphologies of ZnO nanorod arrays. The heights and diameters of ZnO nanorods can be tuned by controlling the electrodeposition parameters.     

Aligned ZnO nanorod arrays fabricated on Si substrate by solution deposition

Aligned ZnO nanorod arrays were fabricated by chemical solution deposition based on Si substrate which was spin coated with ZnO colloid as nucleation seeds. Their microstructures were characterized by X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy. The results indicated that ZnO nanorods nucleated and grew vertically on Si substrates along the [0 0 1] direction with single-crystalline structure. The diameter of ZnO nanorods was greatly affected by the grain size of ZnO seeds. Room-temperature photoluminescence of nanorods has a strong emission band at about 384 nm.     

Large‐area Ag nanorod array substrates for SERS: AAO template‐assisted fabrication,functionalization, and application in detection PCBs

Highly ordered arrays of thiolated β‐cyclodextrin (HS‐β‐CD) functionalized Ag‐nanorods (Ag‐NRs) with plasmonic antennae enhancement of electrical field have been achieved for encapsulation and rapid detection of polychlorinated biphenyls (PCBs). The large‐area ordered arrays of rigid Ag‐NRs supported on copper base were fabricated via porous anodic aluminum oxide (AAO) template‐assisted electrochemical deposition. The inter‐nanorod gaps between the neighboring Ag‐NRs were tuned to sub‐10 nm by thinning the pore‐wall thickness of the AAO template using diluted H₃PO₄. The nearly perfect large‐area ordered arrays of Ag‐NRs supported on copper base render these systems excellent in surface‐enhanced Raman scattering (SERS) performance with uniform electric field enhancement, as testified by the SERS spectra and Raman mappings of rhodamine 6 G. Furthermore, the Ag‐NRs were functionalized with HS‐β‐CD molecules so as to capture the apolar PCB molecules in the hydrophobic cavity of the CD. Compared to the ordinary undecorated SERS substrates, the HS‐β‐CD modified Ag‐NR arrays exhibit better capture ability and higher sensitivity in rapid detection of PCBs. Copyright © 2012 John Wiley & Sons, Ltd.     

The structural and optical properties of ZnO nanorod arrays

High quality vertical-aligned ZnO nanorod arrays were synthesized by a simple vapor transport process on Si (111) substrate at a low temperature of 520 °C. Field-emission scanning electron microscopy (FESEM) showed the nanorods have a uniform length of about 1 μm with diameters of 40-120 nm. X-ray diffraction (XRD) analysis confirmed that the nanorods are c-axis orientated. Selected area electron diffraction (SAED) analysis demonstrated the individual nanorod is single crystal. Photoluminescence (PL) measurements were adopted to analyze the optical properties of the nanorods both a strong UV emission and a weak deep-level emission were observed. The optical properties of the samples were also tested after annealing in oxygen atmosphere under different temperatures, deep-level related emission was found disappeared at 600 °C. The dependence of the optical properties on the annealing temperatures was also discussed.     

Field electron emission improvement of ZnO nanorod arrays after Ar plasma treatment

Vertically well-aligned single crystal ZnO nanorod arrays were synthesized and enhanced field electron emission was achieved after radio-frequency (rf) Ar plasma treatment. With Ar plasma treatment for 30 min, flat tops of the as-grown ZnO nanorods have been etched into sharp tips without damaging ZnO nanorod geometrical morphologies and crystallinity. After the Ar ion bombardment, the emission current density increases from 2 to 20 μA cm⁻² at 9.0 V μm⁻¹ with a decrease in turn-on voltage from 7.1 to 4.8 V μm⁻¹ at a current density of 1 μA cm⁻², which demonstrates that the field emission of the as-grown ZnO nanorods has been efficiently enhanced. The scanning electron microscopy (SEM) results, in conjunction with the results of transmission electron microscopy (TEM), Raman spectroscopy and photoluminescence observation, are used to investigate the mechanisms of the field emission enhancement. It is believed that the enhancements can be mainly attributed to the sharpening of rod tops, and the decrease of electrostatic screening effect.     

Amplification of raman scattering by localized plasmons in silver nanoparticles on the surface of zinc oxide nanorods

The magnetron sputtering of Ag nanoparticles onto ZnO nanorod arrays is studied. The lateral faces of the nanorods are coated with nanoparticles at a much lower density as compared to the flat faces at comparable sputtering times. The silver density is high on the edges of the lateral faces of the nanorods. The plasmon absorption in the synthesized arrays of nanorods coated with individual Ag nanoparticles is maximal at 450?C500 nm. The appearance of local plasmon excitations increases the intensity of the multiphonon processes with the participation of ZnO polar modes in Raman spectra. The cross section of resonance Raman scattering for A ₁(LO) phonon overtones increases with the equivalent Ag film thickness.     

Modulation of field emission properties of vertically aligned ZnO nanorods with aspect ratio and number density

Vertically aligned ZnO nanorod arrays with different aspect ratios were synthesized by hybrid wet chemical route. Modulation of the field emission properties (FE) with aspect ratio of ZnO nanorods was examined. With the increase in the aspect ratio, the emission current density increases from 0.02 to 8 μA/cm² at 7.0 V/μm. Turn-on voltage was seen to decrease from 9.6 to 7 V/μm at a current density of 10 μA/cm² with the increase in aspect ratio in the ZnO films. The interrelation between the FE characteristics (emission thresholds, current density, surface uniformity, etc.) and microstructure of the ZnO nanostructure obtained from scanning electron microscopy (SEM) and atomic force microscopy (AFM) was discussed. Quality of the ZnO nanorods was also examined by using Raman spectroscopy and Fourier transformed infrared spectroscopy (FTIR). It was found that the observed enhancements of FE characteristics could mainly be attributed to the increase in aspect ratio and associated number density of ZnO nanorods.     

Controlling the orientation of ZnO nanorod arrays using TiO<Subscript>2</Subscript> thin film templates dip-coated by sol–gel

The oriented ZnO nanorod arrays have been synthesized on a silicon wafer that coated with TiO₂ films by aqueous chemical method. The morphologies, phase structure and the photoluminescence (PL) properties of the as-obtained product were investigated by field-emission scanning electron microscopy (FE-SEM), X-ray diffractometer (XRD), transmission electron microscope (TEM) and PL spectrum. The nanorods were about 100 nm in diameter and more than 1 μm in length, which possessed wurtzite structure with a c axis growth direction. The room-temperature PL measurement of the nanorod arrays showed strong ultraviolet emission. The effect of the crystal structure and the thickness of TiO₂ films on the morphologies of ZnO nanostructures were investigated. It was found that the rutile TiO₂ films were appropriate to the oriented growth of ZnO nanorod arrays in comparison with anatase TiO₂ films. Moreover, flakelike ZnO nanostructures were obtained with increasing the thickness of anatase TiO₂ films.     

硝酸铟诱导的电沉积氧化锌纳米柱光学性质裁剪

为在新型太阳能电池等光电器件中应用ZnO纳米结构,需要对ZnO纳米结构阵列的几何形貌及光电物理性质进行裁剪与操控。采用电化学沉积路线制备ZnO纳米柱阵列,In(NO3)3与NH4NO3两种盐类被溶入在传统Zn(NO3)2主电解液中。对ZnO纳米柱阵列进行扫描电子显微镜、透射反射光谱、光致发光光谱测试,分析其形貌与光电物理性质。随着引入的In(NO3)3浓度的增加,ZnO纳米柱阵列的平均直径随之由57 nm减小至30 nm。同时ZnO纳米柱的阵列密度也可降低,进而增大纳米柱间距至41 nm。由于新的盐类的引入,ZnO纳米柱的光学带隙由3.46 eV蓝移至3.55 eV。随着电解液中In(NO3)3的增加,ZnO纳米柱的斯托克斯位移由198 meV减小至154 meV,ZnO纳米柱中的非辐射复合可以得到一定程度的抑制。通过在主电解液中引入In(NO3)3与NH4NO3两种盐类,可对ZnO纳米柱的直径、密度、间距、透射反射率、光学带隙、近带边发射与非辐射复合进行操控与裁剪。     

Synthesis and Characteristics of Electrodeposited CoxZn1-x Nanorods

CoxZn1-x nanorod arrays were fabricated by electrodeposition in porous anodic aluminum oxide templates at different electric potentials. X-ray diffraction and transmission electron microscopy indicate that highly-ordered and uniform nanorods have been fabricated. The amounts of Co and Zn contents are investigated using energy dispersive spectroscopy, which demonstrates that the atom ratio of the alloy nanorods changes with the deposition potential. In addition, magnetic measurements show that the magnetic isotropy Co-rich CoZn nanorods will change to magnetic anisotropy nanorods with the easy axis parallel to the rod long axis with decreasing Co content.     

Effect of heat and time-period on the growth of ZnO nanorods by sol–gel technique

Sol–gel routes to metal oxide nanoparticles in organic solvents under exclusion of water have become a versatile alternative to aqueous methods. We focus on the preparation of well-aligned ZnO nanorod arrays using non-aqueous sol–gel synthesis route, where ZnO nanorods arrays have been grown on glass substrates. This work provides a systematic study of controlled morphology and crystallinity of ZnO nanorod arrays. The investigation demonstrates that the synthesis process conditions of ZnO thin film have strong influences on the morphology and crystallinity of the ZnO nanorod arrays grown thereon, where non-aqueous process offers the possibility of better understanding and controlling the reaction pathways on the molecular level, enabling the synthesis of nanomaterials with high crystallinity and well-defined, uniform particle morphologies. Here the annealing temperature plays an important role on the growth of nanostructures of the ZnO grains and nanorod arrays. The scanning electron microscopy (SEM) image shows that the growth of ZnO nanorod arrays are high-quality single crystals growing along the c-axis perpendicular to the substrates. A detailed analysis of the growth characteristics of ZnO nanostructures as functions of growth time is also reported.