Synthesis and electronic behaviors of TiO2/carbon clusters/Cr2O3 composite materials

Nano-structured TiO₂/carbon clusters/Cr₂O₃ composite material has been successfully obtained by the microwave treatment of a TiO(acac)/Cr(acac)₃/epoxy resin complex. The compositions of the composite materials were determined using ICP, elemental analysis and surface characterization by SEM-EDX, TEM and XRD. ESR spectral examinations suggest the possibility of an electron transfer in the process of TiO₂ → carbon clusters → Cr₂O₃ with an oxidation site at TiO₂ particles and a reduction site at Cr₂O₃ particles. The preliminary experimental results show that the calcined materials could decompose methylene blue under visible-light irradiation.     

Preparation and surface encapsulation of hollow TiO nanoparticles for electrophoretic displays

Hollow black TiO nanosparticles were obtained via deposition of inorganic coating on the surface of hollow core-shell polymer latex with Ti(OBu)₄ as precursor and subsequent calcination in ammonia gas. Hollow TiO particles were characterized by scanning electron microscope, transmission electronic microscopy, X-ray diffraction, and thermogravimetric analysis. Encapsulation of TiO via dispersion polymerization was promoved by pretreating the pigments with 3-(trimethoxysilyl) propyl methacrylate, making it possible to prepare hollow TiO-polymer particles. When St and DVB were used as polymerization monomer, hollow TiO-polymer core-shell particles came into being via dispersion polymerization, and the lipophilic degree is 28.57%. Glutin-arabic gum microcapsules containing TiO-polymer particles electrophoretic liquid were prepared using via complex coacervation. It was founded that hollow TiO-polymer particles had enough electrophoretic mobility after coating with polymer.     

Mesoporous carbon-titania nanocomposites for high-power Li-ion battery anode material

We have investigated the Li-ion battery anode properties of several kinds of mesoporous composites of carbon and titanium dioxides (titania, TiO₂) prepared by tri-constituent co-assembly method. The maximum reversible capacity (197 mAh/g) at current density of 50 mA/g was obtained for the composite of TiO₂:carbon=7:3 calcined at 600 °C. It was also found that the composite maintained the high reversible capacity as large as 109 mAh/g even at the high current density of 1000 mA/g.     

Fabrication of TiO2 μ-donuts by sol-gel spin coating using a polymer mask

TiO₂ μ-donuts have been fabricated on glass and silicon substrates using polymer masks in combination with a sol-gel technique. Cylindrical poly(methyl methacrylate) (PMMA) nanopillars have been created using a composite polymer of polystyrene (PS) and PMMA followed by careful removal of the PS. Atomic force microscopy (AFM) analyses show that the height and diameter of the PMMA cylinders used as the mask are 440 ± 5 nm and 2.1 ± 0.2 μm, respectively. The cylindrical PMMA nanopillars have been coated with the sol of the TiO₂ precursor by a spin coating technique and annealed in air at elevated temperature to remove the PMMA mask. Removal of the PMMA mask has resulted in the formation of well ordered μ-donuts of TiO₂ on silicon surfaces. The interior and exterior heights of the TiO₂ μ-donuts are found to be 373 ± 152 nm and 457 ± 136 nm, respectively; and the interior and exterior diameters of the TiO₂ μ-donuts are found to be 1.33 ± 0.63 μm and 2.82 ± 0.50 μm, respectively. X-ray photoelectron spectroscopy (XPS) spectra of the TiO₂ μ-donuts as well as the smooth TiO₂ thin film showed signals from Ti and O confirming the presence of TiO₂ with Ti 2p_3/2 and O 1s peaks at 458.8 eV and 530.4 eV, respectively. The O 1s peak of the TiO₂ μ-donuts shows another peak at binding energy 532.0 eV due to SiO₂, as during annealing, the PMMA evaporates and the Si substrate is exposed. The X-ray diffractometer (XRD) pattern of the smooth TiO₂ thin film indicates that the anatase phase is present, with the characteristic peaks observed at 2θ values of 25.4°, 37.4°, and 48° corresponding to (1 0 1), (0 0 4), and (2 0 0) planes, respectively. UV-vis absorption spectra of TiO₂ μ-donuts on glass showed an unusual absorption of light in the visible region at ∼524 nm in addition to the usual UV absorption at ∼337 nm.     

A novel approach towards high-performance composite photocatalyst of TiO2 deposited on activated carbon

TiO₂ photocatalysts deposited on activated carbon (TiO₂/AC) were prepared by dip-hydrothermal method at 180 °C using peroxotitanate as a precursor, then calcinated at 300-800 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and the nitrogen absorption. Their photocatalytic activity was evaluated by degradation of methyl orange (MO). The results showed that TiO₂ particles of anatase type were well deposited on the activated carbon surface. TiO₂/AC calcinated at 600 °C exhibited the best photocatalytic performance. For the comparison, the same photocatalysis experiment was carried out for two mixtures of commercial TiO₂ (Degussa P25) with AC and synthetic TiO₂ with AC. It was found that the composite catalyst TiO₂/AC was better than the two mixtures. Besides, different from fine powdered TiO₂, the granular TiO₂/AC photocatalysts could be easily separated from the bulk solution and reused; indeed, its photocatalytic ability was hardly decreased after a five-cycle for MO degradation. The kinetics of the MO degradation fitted well the Langmuir-Hinshelwood model.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

The microstructure and specific properties of La/HAP composite powder and its coating

La/HAP composite powder, a novel bioactive material, was prepared using co-precipitation method. The La/HAP coating was obtained for the first time through the dip-coating method, starting from the sols of La/HAP and TiO₂ particles. The compositions and coating of as-produced La/HAP composite powder sintered at temperatures from 300 to 750 °C were analyzed by means of X-ray diffraction (XRD). The changes of the ion groups in as-prepared La/HAP composite powder were characterized by using Fourier transform infrared (FTIR) spectroscopy. Their surface morphologies were observed by means of scanning electron microscope (SEM). The results show that the La/HAP composite powder has higher thermostability than pure HAP powder and La can refine HAP particle and restrain the decomposition of HAP. Consequently, in coating process the heat-treatment temperature is lower (750 °C) using the synthesized La/HAP powder than that using pure HAP (900 °C). The La/HAP coating mainly contains HAP, TiP or Ti₃P₅ and TiO₂ phases as well as a little CaTiO₃ crystal, a very ideal composition to enhance bioactivity of biomaterials. These unique properties of the La/HAP composite powder are beneficial to enhance the strength and bioactivity of coating when it is used as a starting material in coating process.     

Synthesis and gas sensing characteristic based on metal oxide modification multi wall carbon nanotube composites

A new type of gas sensing material based on metal oxide modification multi wall carbon nanotube (MO/MWCNT) composites is presented since the interface between the composites enhance the carrier density so as to improve the gas sensitivity. Three kinds of MO/MWCNT composite materials, such as ZnO/MWCNT, SnO₂/MWCNT and TiO₂/MWCNT, have been acquired in situ growth using catalytic pyrolysis method. The MO nano particles have decorated on side of MWCNTs, whereas the introduction of SnO₂ nano particles makes part of MWCNT showing two-dimensional form of carbon nano-wall structure. Among four kinds of cathode of ZnO/MWCNTs, SnO₂/MWCNTs, TiO₂/MWCNTs and pure MWCNT composite film, TiO₂/MWCNTs composite has the lowest threshold electric field required to draw current of 12 μA has been found to be ∼1.2 V/μm, and also TiO₂/MWCNTs composite has the highest sensitivity of 16% to ethanol. The TiO₂/MWCNTs composite is superior to the others both in vacuum electron transportation and gas sensitivity.     

Evolution with temperature of a single sol-gel TIO2 layer on sapphire (α-Al2O3) (0 0 0 1)

TiO₂ sol-gel layer has been deposited on single crystal sapphire (0 0 0 1) substrate. Evolution of the layer microstructure with the thermal treatment in the range 100-1100 °C has been studied using X-ray diffraction and X-ray reflectometry. TiO₂ layer density first increases with temperature up to 800 °C and then decreases with the appearance of a high roughness finally leading to anatase islands formation. The single crystal nature of the substrate seems to contribute to hinder the transformation of the anatase phase into the rutile phase and to induce a preferred orientation of the TiO₂ islands.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.     

The structure and photocatalytic activity of TiO2 thin films deposited by dc magnetron sputtering

This paper seeks to determine the optimal settings for the deposition parameters, for TiO₂ thin film, prepared on non-alkali glass substrates, by direct current (dc) sputtering, using a ceramic TiO₂ target in an argon gas environment. An orthogonal array, the signal-to-noise ratio and analysis of variance are used to analyze the effect of the deposition parameters. Using the Taguchi method for design of a robust experiment, the interactions between factors are also investigated. The main deposition parameters, such as dc power (W), sputtering pressure (Pa), substrate temperature (°C) and deposition time (min), were optimized, with reference to the structure and photocatalytic characteristics of TiO₂. The results of this study show that substrate temperature and deposition time have the most significant effect on photocatalytic performance. For the optimal combination of deposition parameters, the (1 1 0) and (2 0 0) peaks of the rutile structure and the (2 0 0) peak of the anatase structure were observed, at 2θ ∼ 27.4°, 39.2° and 48°, respectively. The experimental results illustrate that the Taguchi method allowed a suitable solution to the problem, with the minimum number of trials, compared to a full factorial design. The adhesion of the coatings was also measured and evaluated, via a scratch test. Superior wear behavior was observed, for the TiO₂ film, because of the increased strength of the interface of micro-blasted tools.     

Visible-light-activated Ce-Si co-doped TiO2 photocatalyst

To enhance the visible photocatalytic activity and thermal stability of TiO₂, Ce-Si co-doped TiO₂ materials were synthesized through a nonaqueous method of which the purpose was to reduce the aggregation between TiO₂ particles. The obtained materials maintained anatase phase and large surface area of 103.3 m² g⁻¹ even after calcined at 800 °C. The XPS results also indicated that Si was weaved into the lattice of TiO₂, and Ce mainly existed as oxides on the surface of TiO₂ particles. The doped Si might enhance surface area and suppress transformation from anatase to rutile, while the doped Ce might cause visible absorption and inhibit crystallite growth during heat treatment. Evaluated by decomposing dye Rhodamine B, visible photocatalytic activity of Ce-Si co-doped TiO₂ was obviously higher than that of pure TiO₂ and reached the maximum at Ce and Si contents of 0.5 mol% and 10 mol%.     

Preparation of alkaline solid polymer electrolyte based on PVA-TiO2-KOH-H2O and its performance in Zn-Ni battery

A novel composite alkaline polymer electrolyte based on poly(vinyl alcohol) (PVA) polymer matrix, titanium dioxide (TiO₂) ceramic fillers, KOH, and H₂O was prepared by a solution casting method. The properties of PVA-TiO₂-KOH alkaline polymer electrolyte films were studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and AC impedance techniques. DSC and XRD results showed that the domain of amorphous region in the PVA polymer matrix augmented when TiO₂ filler was added. The SEM result showed that TiO₂ particles dispersed into the PVA matrix although some TiO₂ aggregates of several micrometers were formed. The alkaline polymer electrolyte showed excellent electrochemical properties. The room temperature (20 °C) ionic conductivity values of typical samples were between 0.102 and 0.171 S cm⁻¹. The Zn-Ni secondary battery with the alkaline polymer electrolyte PVA-TiO₂-KOH had excellent electrochemical property at the low charge-discharge rate.     

The photocatalytic application and regeneration of anatase thin films with embedded commercial TiO2 particles deposited on glass microrods

Anatase thin films (<200 nm in thickness) embedding Degussa P25 TiO₂ were prepared by sol-gel method. TiO₂-anatase thin films were deposited on a fiberglass substrate and then ground to obtain glass microrods containing the composite films. The film structure was characterized using Raman spectroscopy, atomic absorption and UV-vis spectrophotometry, and atomic force microscopy. The photocatalytic activity of the composite films, calcined at 450 °C, and the regeneration of the activity under the same experimental conditions, were assessed using gas chromatography to study the photodegradation of phenol, an industrial pollutant, in water under 365 nm irradiation. The film with 15.0 wt.% of P25 TiO₂ was found to be more photoactive (54 ppm of degraded phenol at 6 h of illumination) than the other ones.     

Synthesis and optical properties of amorphous C-Si-O particles

Amorphous C-Si-O particles, prepared by pyrolyzing PDMS in a horizontal furnace using the carrier gas N₂/H₂ at 900 °C, were characterized by electron microscopy, X-ray diffraction, FTIR spectroscopy, X-ray photoelectron spectroscopy and fluorescence spectroscopy. The particles possess four luminescence peaks at 440, 465, 533 and 620 nm, and produce stable red, green or blue light emissions at room temperature when irradiated with appropriate wavelengths, the four peaks attribute to different defect centers in the particles. And the particles exhibit the highest photoluminescence intensity when annealed at 600 °C.     

Photocatalytic behavior of heavy La-doped TiO2 films deposited by pulsed laser deposition using non-sintered target

We have investigated the control of photocatalytic behavior under deposited conditions of non-sintered target of different molar ratios with TiO₂ and La₂O₃ from 1:0 to 1:2 for heavily La doping, and post-annealing temperature from 600 °C to 1000 °C for crystallizing by pulsed laser deposition. We have successfully crystallized heavily La-doped TiO₂ films with post-annealing temperature over 800 °C and with molar ratio of TiO₂:La₂O₃ over 1:1 on a quartz substrate. Heavily La-doped TiO₂ films are observed the decomposition of methylene blue and a water-splitting reaction in photocatalytic behavior under Xe light irradiation. When stoichiometric La-doped TiO₂ (TiO₂:La₂O₃ = 1: 1) is synthesized with heat-treatment at 900 °C, the best results are obtained under photocatalytic behavior and pure La₂Ti₂O₇ crystalline were obtained.     

Structural, optical, and electrical properties of p-type NiO films and composite TiO2/NiO electrodes for solid-state dye-sensitized solar cells

p-Type nickel oxide thin films were prepared by sol-gel method, and their structural, optical and electrical properties were investigated. The Ni(OH)₂ sol was formed from nickel (II) acetate tetrahydrate, Ni(CH₃COO)₂·4H₂O, in a mixture of alcohol solution and poly(ethylene glycol), and deposited on an ITO substrate by spin coating followed by different heat treatments in air (50-800 °C). The formation and composition of NiO thin film was justified by EDX analysis. It is found that the thickness of the NiO film calcined at 450 °C for 1 h is about 120 nm with average particle size of 22 nm, and high UV transparency (∼75%) in the visible region is also observed. However, the transmittance is negligible for thin films calcined at 800 °C and below 200 °C due to larger particle size and the amorphous characteristics, respectively. Moreover, the composite electrode comprising n-type TiO₂ and p-type NiO is fabricated. The current-voltage (I-V) characteristics of the composite TiO₂/NiO electrode demonstrate significant p-type behavior by the shape of the rectifying curve in dark. The effect of calcination temperature on the rectification behavior is also discussed.