A study of Eu2O3, Sc2O3 co-doped tungsten matrix impregnated cathode

Eu₂O₃ and Sc₂O₃ co-doped W matrix impregnated cathodes have been prepared by the powder metallurgy method. The constitution of active elements on activated cathode surface is analyzed by in-situ Auger electron spectroscopy. It is found that although Eu exists in the matrix, no Eu is found on the cathode surface due to the formation of a stable Eu containing compound. Sc, Ba and O diffuse to the surface of the cathode and form an active surface layer during the activation period whereas the stable Eu-compound cannot liberate free Eu, which can diffuse from the cathode to the surface. The active substance of Sc, Ba and O on the cathode surface contribute to the emission property.     

Visible luminescence of Al2O3 nanoparticles embedded in silica glass host matrix

This paper deals with the sol-gel elaboration and defects photoluminescence (PL) examination of Al₂O₃ nanocrystallites (size ∼30 nm) confined in glass based on silica aerogel. Aluminium oxide aerogels were synthesized using esterification reaction for hydrolysis of the precursor and supercritical conditions of ethyl alcohol for drying. The obtained nanopowder was incorporated in SiO₂ host matrix. After heating under natural atmosphere at 1150 °C for 2 h, the composite Al₂O₃/SiO₂ (AS) exhibited a strong PL bands at 400-600 and 700-900 nm in 78-300 K temperature range. PL excitation (PLE) measurements show different origins of the emission. It was suggested that OH-related radiative centres and non-bridging oxygen hole centres (NBOHCs) were responsible for the bands at 400-600 and 700-900 nm, respectively.     

Preparation and characterization of scandia and Re doped tungsten matrix impregnated cathode

The paper describes the preparation and emission property of scandia and Re doped tungsten matrix impregnated cathode. By an easy and reproducible way, solid-liquid doping combined with two-step reduction, powders of tungsten particles covered with scandium oxide were obtained. Compared with scandia mixed tungsten powders prepared by mechanically mixing, scandia and rhenium doped tungsten powders had smaller particle size, for example, scandia (3 wt%) and Re (5 wt%) doped tungsten powders had the average size of about 50 nm in diameter. Based on this kind of powder, scandia and Re doped tungsten matrix with the sub-micrometer sized tungsten grains and a more uniform distribution of Sc₂O₃ were obtained in this paper. Scandia and Re doped tungsten matrix impregnated cathode had shown excellent emission property and good emission uniformity. The space charge limited current densities of more than 58A/cm² at 900 °C_b could be obtained and the work function of this cathode was as low as 1.18 eV.     

Synthesis and characterization of room-temperature ferromagnetism in Fe- and Ni-co-doped In2O3

Observation of room-temperature ferromagnetism in Fe- and Ni-co-doped In₂O₃ samples (In_0.9Fe_0.1−xNi_x)₂O₃ (0?x?0.1) prepared by citric acid sol-gel auto-igniting method is reported. All of the samples with intermediate x values are ferromagnetic at room-temperature. The highest saturation magnetization (0.453 μ_B/Fe+Ni ions) moment is reached in the sample with x=0.04. The highest solubility of Fe and Ni ions in the In₂O₃ lattice is around 10 and 4 at%, respectively. The 10 at% Fe-doped sample is found to be weakly ferromagnetic, while the 10 at% Ni-doped sample is paramagnetic. Extensive structure including Extended X-ray absorption fine structure (EXAFS), magnetic and magneto-transport including Hall effects studies on the samples indicate the observed ferromagnetism is intrinsic rather than from the secondary impurity phases.     

Red colored transparent PMMA-SiO2 hybrid films

Red colored transparent organic-inorganic hybrids films of a cross-linked polymethyl-methacrylate (PMMA) and silica were prepared via the sol-gel route using tetraethoxy-silane (TEOS) as precursor and a commercial organic red dye. 3-(Trimethoxysilyl) propyl methacrylate (TMSPM) was used to make compatible the organic and inorganic components of the precursor solution mixture. Four type of colored hybrid films were deposited using precursor solutions with the reactants molar ratio 1:0.5:1 for TEOS: TMSPM:MMA, respectively, and four different weight contents of the organic red dye. The hybrid films were studied by Fourier transform infrared spectroscopy, atomic force microscopy and optical transmission and reflection spectroscopy. The hardness of the films was determined from a pencil hardness test referred to ASTM Standard D 3363-92. The results showed that the colored hybrid films have a thickness of about 2 μm and consist of a homogeneous cross-linked organic-inorganic matrix with embedded dye molecules very well dispersed. The hardness of the hybrid films was enhanced with respect to that of the pure organic component. The AFM measurements showed very flat and smooth film surfaces with rms average roughness about 0.3 nm. The optical properties of the hybrid films including their color properties were determined from optical transmission and reflection spectroscopy. We found that the intensity of the color in the hybrid films and the corresponding color coordinates depend on the amount of red dye in the hybrid films. Photodegradation studies were performed by monitoring the optical density of the films as a function of the exposure time to illumination for several values of illumination intensity.     

Combustion synthesis and photoluminescence of Eu, Dy-doped La2Zr2O7 nanocrystals

A facile and energy saving sol-gel combustion method has been used to prepare La₂Zr₂O₇ nanocrystallines. The pyrochlore La₂Zr₂O₇ nanocrystals have been obtained at a relatively low temperature with the grain size ranging from 45 to 70 nm. Eu³⁺ and Dy³⁺ have been introduced into the La₂Zr₂O₇ crystal structure, respectively, and the intense photoluminescence was observed. The relative intensity of electric dipole transition and magnetic dipole transition is considered for luminescence emission both of Eu³⁺ and Dy³⁺. The dependence of luminescence intensity on dopant concentration and the effect of Dy³⁺ co-doping on Eu³⁺ luminescence are also discussed.     

Sol-gel synthesis of iron(III) oxyhydroxide nanostructured monoliths using Fe(NO3)3·9H2O/CH3CH2OH/NH4OH ternary system

Iron(III) oxyhydroxide xerogels were prepared through sol-gel technology, using iron(III) nitrate nonahydrate as precursor, ethanol as solvent and ammonium hydroxide as gelation agent. This base is used for propylene oxide substitution, which was the gelation agent in previous works. Synthesis of a gel using NH₄OH as a gelation agent is an innovative result with this type of precursor, since with metal salts the addition of a strong base commonly results in precipitation of the solid. The gel synthesis was achieved by controlling the base addition time. The dried material has a residual amount of organic impurities, in contrast with the significant amount detected in xerogels prepared using propylene oxide. The iron phase prevailing in the produced xerogels can be defined as γ-FeO(OH) (lepidocrocite), according to FTIR and Mössbauer analyses. The xerogels are formed by large clusters of well connected nanocrystallites of this phase. XRD revealed a crystalline phase retained inside the iron oxyhydroxide amorphous structure, which corresponds to NH₄NO₃ and results from the combination of NO₃⁻ and NH₄⁺ ions in solution. The produced xerogel has a promising composition to be an oxidizing composite for the energetic materials area.     

Effect of hydroxyl groups on Er doped Bi2O3-B2O3-SiO2 glasses

A series of Er³⁺-doped Bi₂O₃-B₂O₃-SiO₂-Na₂O glasses with different hydroxyl groups were prepared and the interaction between the Er³⁺ ions and OH groups was investigated. Infrared spectra were measured in order to calculate the exact content of OH groups in samples. The observed increase of the fluorescence lifetime with the oxygen bubbling time has been related to the reduction in the OH content concentration evidenced by infrared (IR) absorption spectra, which confirmed that the OH groups were dominant quenching centers of excited Er³⁺ and a cause of concentration quenching of 1.5 μm band emission. Various nonradiative decay rates from ⁴I_13/2 of Er³⁺ with the change of OH content were determined from the fluorescence lifetimes and radiative decay rates, which were calculated on the basis of Judd-Ofelt theory.     

Low-temperature hydrothermal synthesis of highly photoactive mesoporous spherical TiO2 nanocrystalline

TiO₂ microspheres with mesoporous textural microstructures and high photocatalytic activity were prepared by hydrothermal treatment of mixed solution of titanium sulfate and urea with designed time. The prepared samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and N₂ adsorption-desorption measurements. The photocatalytic activity was evaluated via the photocatalytic oxidation of acetone in air at room temperature. The results show that the hydrothermal time significantly influences on the morphology, microstructure and photocatalytic activity of the as-prepared samples. With increasing hydrothermal time, specific surface areas and pore volumes decrease, contrarily, the crystallite size and relative anatase crystallinity increase. The photocatalytic efficiency of the as-prepared samples is obviously higher than that of commercial Degussa P25 (P25) powders. Especially, the as-prepared TiO₂ powders by hydrothermal treatment for 7 h shows the highest photocatalytic activity, which exceeds that of P25 by a factor of more than 2 times.     

Photoluminescence of Y2O3:Eu thin film phosphors by sol-gel deposition and rapid thermal annealing

Y₂O₃:Eu³⁺ phosphor films have been developed by using the sol-gel process. Comprehensive characterization methods such as Photoluminescent (PL) spectroscopy, X-ray diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy were used to characterize the Y₂O₃:Eu³⁺ phosphor films. In this experiment, the XRD profiles show that the Y₂O₃:Eu³⁺ phosphor films crystallization temperature and optimum annealing temperature occur at about 650 and 750 °C, respectively. The optimum dopant concentration is 12 mol% Eu³⁺ and the critical transfer distance (R_c) among Eu³⁺ ions is calculated to be about 0.84 nm. Vacuum environment is more efficient than oxygen and nitrogen to eliminate the OH content and hence yields higher luminescent phosphor films. The PL emission intensity of Y₂O₃:Eu³⁺ phosphor films is also dependent on the annealing time. It was found that the H₂O impurities were effectively eliminated after annealing time of 25 s at 750 °C in vacuum environment. From the experiment results, the schematic energy band diagram of Y₂O₃:Eu³⁺ phosphor films is constructed.     

Facile synthesis and electrochemical properties of hierarchical MnO2 submicrospheres and LiMn2O4 microspheres

Hierarchical MnO₂ submicrospheres have been successfully synthesized by a wet chemical method. The as-prepared products were characterized by means of XRD, SEM, FTIR, TG, and TEM. With the as-prepared MnO₂ submicrospheres as precursors, LiMn₂O₄ microspheres were conveniently prepared by a simple solid-state reaction between MnO₂ and LiOH at a temperature as low as 600 °C. Electrochemical properties of the as-prepared MnO₂ submicrospheres and LiMn₂O₄ microspheres as cathode materials in lithium ion cells were investigated by galvanostatic charge/discharge tests.     

Porous LiNi0.75Co0.25O2 microspheres prepared via a hydrothermal process as cathode material for lithium ion batteries

Porous LiNi_0.75Co_0.25O₂ microspheres are successfully prepared by a simple hydrothermal process by using H[Ni_0.75Co_0.25OOH]₃ and LiOH as starting materials in the presence of urea for the first time. The synthesized samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), specific surface area (S_BET), and electrochemical performance. The synthesized LiNi_0.75Co_0.25O₂ has a good electrochemical performance with an initial discharge capacity of 169.3 mA g⁻¹ and good capacity retention of 96.7% after 50 cycles at 0.2 C (25 mA g⁻¹). The electrochemical lithium ion insertion/extraction process is quite reversible even at 5 C. Furthermore, the structure in the charge-discharge process is stable and the impedance increased slowly during cycling.     

Sol-gel synthesis and photoluminescence of CaSiO3:Eu nanophosphors using novel silicate sources

In this paper, seven kinds of silane coupling reagents were employed as silicate sources to prepare CaSiO₃:Eu³⁺ phosphors by the sol-gel method. The different silicate precursors were used to adjust the microstructure and size of the resulting phosphors. The crystallite size of phosphors is in the range of 30-35 nm and some of them show regular microstructure after high-temperature thermolysis. The photoluminescence properties show that all of them exhibit the characteristic fluorescence ⁵D₀→⁷F_J (J=0, 1, 2, 3, 4) of the Eu³⁺ ion and the strongest one is the red emission at 610 nm. Furthermore, the emission quantum efficiency (η) of the ⁵D₀ Eu³⁺ excited state has been calculated to be around 33% from the emission spectrum and the lifetime of the Eu³⁺ first excited level (τ, ⁵D₀).     

Superconductivity and non-metallicity induced by doping the topological insulators Bi2Se3 and Bi2Te3

We show that by Ca doping the Bi₂Se₃ topological insulator, the Fermi level can be fine tuned to fall inside the band gap and therefore suppresses the bulk conductivity. Non-metallic Bi₂Se₃ crystals are obtained. On the other hand, the Bi₂Se₃ topological insulator can also be induced to become a bulk superconductor, with T_c∼3.8 K, by copper intercalation in the van der Waals gaps between the Bi₂Se₃ layers. Likewise, an as-grown crystal of metallic Bi₂Te₃ can be turned into a non-metallic crystal by slight variation in the Te content. The Bi₂Te₃ topological insulator shows small amounts of superconductivity with T_c∼5.5 K when reacted with Pd to form materials of the type Pd_zBi₂Te₃.     

Immiscibility in the Fe3O4-FeCr2O4 spinel binary

A recent thermodynamic model of mixing in spinel binaries, based on changes in cation disordering (x) between tetrahedral and octahedral sites [Am. Mineral. 68 (1983) 18, 69 (1984) 733], is investigated for applicability to the Fe₃O₄-FeCr₂O₄ system under conditions where incomplete mixing occurs. Poor agreement with measured consolute solution temperature and solvus [N. Jb. Miner. Abh. 111 (1969) 184] is attributed to neglect of: (1) ordering of magnetic moments of cations in the tetrahedral sublattice antiparallel to the moments of those in the octahedral sublattice and (2) pair-wise electron hopping between octahedral site Fe³⁺ and Fe²⁺ ions. Disordering free energies (ΔG_D), from which free energies of mixing are calculated, are modeled by

     

Multiferroic studies on (BiFeO3)m(BaTiO3)n superlattice structures

BiFeO₃ has been studied extensively due to its room temperature multiferroic features and has been proven as a promising candidate for device applications. But BiFeO₃ possesses some drawbacks like high leakage current and complicated magnetic ordering, giving rise to a canted antiferromagnetic behavior. Hence, a superlattice approach of BiFeO₃ and BaTiO₃ with a good lattice matching was fabricated and the room temperature ferroelectric and ferromagnetic properties were studied. The macroscopic and local probe studies reveal a ferroelectric nature at room temperature, and most importantly a weak ferromagnetic like behavior was observed. The ferromagnetic behavior is expected to arise due to the variation introduced in the spin modulation of single BiFeO₃ layer due to the superstructure formation.     

Dielectric spectroscopy on Bi3Zn2Sb3O14 ceramic: an approach based on the complex impedance

The dielectric properties and loss of Bi_1.5ZnSb_1.5O₇ a poor-semiconducting ceramic were investigated by impedance spectroscopy, in the frequency range from 5 Hz to 13 MHz. Electric measurements were performed from 100 to 700 °C. Pyrochlore type phase was synthesized by the polymeric precursor method. Dense ceramic with 97% of the theoretical density was prepared by sintering via constant heating rate. The dielectric permittivity dependence as a function of frequency and temperature showed a strong dispersion at frequency lower than 10 kHz. The losses exhibit slight dependence with the frequency at low temperatures presenting a strong increase at temperatures higher than 400 °C. A decrease of the loss magnitude occurs with increasing frequency. Relaxation times were extracted using the dielectric functions Z″(ω) and M″(ω). The plots of the relaxation times τ_Z′ and τ_M″ as a function of temperature follow the Arrhenius law, where a single slope is observed with activation energy values equal to 1.38 and 1.37 eV, respectively.     

Elaboration and characterization of TiO2 nanoparticles incorporated in SiO2 host matrix

Nanometer-scale TiO₂ particles have been synthesized by sol-gel method. It was incorporated in a glass-based silica aerogel. The composite was characterized by various techniques such as particle size analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), X-ray diffraction (XRD), infrared spectroscopy (IR) and photoluminescence (PL). The bulk glass presents a strong luminescence at wavelengths ranging from 750 to 950 nm. This PL was attributed to various non-bridging oxygen hole centers (NBOHCs) defects resulting from thermal treatment and crystallization of TiO₂ at the interface between titania nanoparticles and silica host matrix.     

Physical properties of BaMg1/3Nb2/3O3-BaCo1/3Nb2/3O3 solid solutions

Structural, electric and magnetic properties of Ba₃Mg_1−xCo_xNb₂O₉ based dielectric ceramic compounds have been studied. The samples, prepared by a solid state reaction method, were characterised by X-ray powder diffraction (XRPD), electron microscopy (SEM), dielectric (ε(T)) and magnetic measurements (χ⁻¹(T)). The XRPD analyses showed that the crystal structure of these compounds does change by the increase of substitution degree, passing from a superstructure hexagonal-type, (no. 164), space group (SG) to a simple structure cubic-type, (no. 221), SG. However, the evolution of the elementary unit cell lattice parameter can be followed and it exhibit a linear increasing tendency with increase in the substitution, indicating the existence of a solid solution through out the investigated range of substitution (0-1). The microstructure analysis shows a variation in the grain size and also the porosity of the samples with the degree of substitution. The results are in good agreement with that of dielectric measurements, which also showed that the dielectric constant (ε) increases with the increase of cobalt content. The magnetic characterization of cobalt substituted samples showed an antiferromagnetic type super-exchange interaction between these magnetic ions. At the same time, the values of effective magnetic momentum (μ_eff) are close to the value that corresponds to Co²⁺ free ions. The study highlights the possibility of modelling these materials by substitutions, in order to improve properties of negative-positive-zero (NPO) type dielectric applications.     

Optical properties of sol-gel fabricated Ni/SiO2 glass nanocomposites

Nickel nanoparticles were grown in silica glass by annealing of the sol-gel prepared silicate matrices doped with nickel nitrate. TEM characterization of Ni/SiO₂ glass proves the formation of isolated spherical nickel nanoparticles with mean sizes 6.7 and 20 nm depending on annealing conditions. The absorption and photoluminescence spectra of Ni/SiO₂ glasses were measured. In the absorption spectra, we observed the band related to the surface plasmon resonance (SPR) in Ni nanoparticles. The broadening of SPR was observed with decrease of Ni nanoparticle size. The width of the surface plasmon band decreases 1.5 times at the lowering of temperature from 293 to 2 K because of strong electron-phonon interaction. The spectra proved the creation of nickel oxide NiO clusters and Ni²⁺ ions in silica glass as well.