Dispersion stability of a ceramic glaze achieved through ionic surfactant adsorption

The adsorption of cetylpyridinium chloride (CPC) and sodium dodecylbenzenesulfonate (SDBS) onto a ceramic glaze mixture composed of limestone, feldspar, quartz, and kaolin has been investigated. Both adsorption isotherms and the average particle zeta potential have been studied in order to understand the suspension stability as a function of pH, ionic strength, and surfactant concentration. The adsorption of small amounts of cationic CPC onto the primarily negatively charged surfaces of the particles at pH 7 and 9 results in strong attraction and flocculation due to hydrophobic interactions. At higher surfactant concentrations a zeta potential of more than +60 mV results from the bilayered adsorbed surfactant, providing stability at salt concentrations < or = 0.01 M. At 0.1 M salt poor stability results despite substantial zeta potential values. Three mechanisms for SDBS adsorption have been identified. When anionic SDBS monomers either adsorb by electrostatic interactions with the few positive surface sites at high pH or adsorb onto like charged negative surface sites due to dispersion or hydrophobic interactions, the magnitude of the negative zeta potential increases slightly. At pH 9 this increase is enough to promote stability with an average zeta potential of more than -55 mV, whereas at pH 7 the zeta potential is lower at about -45 mV. The stability of suspensions at pH 7 is additionally due to steric repulsion caused by the adsorption of thick layers of neutrally charged Ca(DBS)2 complexes created when the surfactant interacts with dissolved calcium ions from the calcium carbonate component.     

阴、阳离子表面活性剂混合体系在硅胶/水及硅胶/矿化水界面上的吸附

研究阴、阳离子表面活性剂混合体系(十二烷基氯代吡啶,辛基磺酸钠,辛基三乙基溴化铵/十二烷基苯磺酸钠)在硅胶,纯水和硅胶,矿化水界面上的吸附作用,探讨阴(阳)离子表面活性剂的存在对阳(阴)离子表面活性剂吸附作用的影响．结果表明,阴离子表面活性剂的存在基本不影响阳离子表面活性剂在带负电固体表面的吸附;而阳离子表面活性剂的存在却使本来吸附量就不大的阴离子表面活性剂在带负电的固体表面上不再吸附．在矿化水中阳离子表面活性剂的吸附量比在纯水中明显降低．从硅胶表面吸附机制解释了所得结果．     

Cationic Surfactants as Regulators in Paper Separation of 2‐Nitrophenol and 2,4,6‐Trinitrophenol in Water

The chemical pollutants 2‐nitrophenol (2‐NP) and 2,4,6‐trinitrophenol (2,4,6‐TNP) were studied for their separation from water by the paper capillary permeation adsorption technique by the use of the four cationic surfactants dodecyltrimethylammonium chloride (DTAC), tetradecyltrimethylammonium bromide (TTAB), cetyltrimethylammonium bromide (CTAB), cetylpyridinium chloride (CPC) as regulators. The effect of pH and the concentration of surfactant on the separatability have been investigated. A nearly 100% separatability was obtained for each pollutant at its optimum pH and surfactant concentration. It was shown that the separation was accomplished via surface adsorption onto the fibers of paper. The change in separatability at basic pH 11 with surfactant variety was analyzed. The result shows that the surfactant with a longer chain alkyl group is more effective for the separation of 2‐NP and the surfactants with 16 carbons in the long chain alkyl group are most effective. The surfactants with 12 carbons or more in the long alkyl group but containing no aromatic group such as pyridyl group are equally effective for accomplishing an efficient separation of 2,4,6‐TNP. Selective separation of 2‐NP from an admixture of 2‐NP plus 2,4,6‐TNP was attempted. The optimum surfactant for each pollutant was tested with seawater for removing the pollutant. The goal of this study is to search for an optimum cationic surfactant and optimum separation conditions for nitrophenols.     

Adsorption and direct probing of fibrinogen and sodium myristate at the air/water interface

Fibrinogen (FB), a serum protein, is considered a major inhibitor of lung surfactant function at the lining layer of the alveoli. In this study, the adsorption of aqueous bovine FB at the air/water interface was investigated with tensiometry and directly probed for the first time with ellipsometry and infrared reflection adsorption spectroscopy (IRRAS). The tension results show that FB has moderate surface activity. The surface densities of FB were calculated by using two different ellipsometry models to range from 3±0.2 to 17±2 mg/m², for 7.5 to 750 ppm of FB in water at 25°C. Although FB at concentrations from 75 to 750 ppm reached about the same steady surface tension value, the surface densities at 750 ppm FB were substantially larger. The same techniques were used for studying aqueous mixtures of 7.5 to 750 ppm FB with 2 mM of sodium myristate (SM) to investigate a possible interaction of the SM with the protein. The behavior of the FB/SM mixtures was found to be close to that of SM alone. The surface tension of the FB/SM mixtures reached values less than 10 mN/m under surface area oscillation at 20 or 80 rpm. These results and the ellipsometry and the IRRAS results indicate that at a concentration of 2 mM SM, FB, up to 750 ppm, does not inhibit the surfactant surface-tension-lowering function. In certain cases the results demonstrate that FB and SM may act cooperatively in lowering the surface tension.     

The effect of adsorbed carboxymethyl cellulose on the cotton fibre adsorption capacity for surfactant

The research reported in this paper demonstrates that the capacity of cotton fibres to adsorb cationic surfactants as well as the rate of the adsorption process can be increased by adsorbing carboxymethyl cellulose (CMC) onto the fibre surfaces; in addition, the adsorption can be restricted to the fibre surface. CMC was deposited by means of adsorption from an aqueous solution. The adsorption of N-cetylpyridinium chloride (CPC) from an aqueous solution onto the CMC-modified fibres was measured using UV-spectrometric determination of the surfactant concentration in the solution. Adsorption onto the cotton fibres was studied in a weakly basic environment (pH 8.5) where cotton fibres are negatively charged and the CPC ion is positively charged. Modification of the fibres by adsorption of CMC introduces new carboxyl groups onto the fibre surfaces, thereby increasing the adsorption capacity of the fibres for CPC. The initial rate of adsorption of CPC increased proportionally with the amount of charge; however, this rate slowed down at high degrees of coverage on fibres with a high charge. The adsorption of cationic surfactant to the anionic surface groups was stoichiometric, with no indication of multilayer or admicelle formation. It was evident that the acidic group content of the fibres was the primary factor determining cationic surfactant adsorption to these fibres.     

Interaction of Reactive Brilliant Red with Cetylpyridinium and Application to Determination of Cationic Surfactant in Water

The microsurface adsorption‐spectral correction technique and light adsorption ratio variation approach were jointly applied to characterization of the interaction of reactive brilliant red (RBR) with cetylpyridinium chloride (CPC) at pH 3.67. The interaction responded with the Langmuir isothermal adsorption. The saturated binding ratio of RBR to CPC is (1.2 ± 0.1): 1, and the bind constant of the RBR‐CPC complex was calculated to be (1.15 ± 0.05) × 10⁵ 1/mol. The interaction was applied to the determination of cationic surfactant in water by the light adsorption ratio variation approach with satisfactory results.     

Dynamic surface tension and its diffusional decay of dodecyl ethoxylates with different homologue distribution

Dynamic surface tension and its diffusional decay have been studied with four different polydisperse C12E7 at different temperatures and different concentrations. The CMC and the headgroup area from equilibrium surface tension were shown with polydispersity and temperature. The chain length of oxyethylene on the surface was derived from comparison between the headgroup area of monodisperse dodecyl ethoxylates and that of polydisperse C12E7. The values for (Deff/D) were deduced with a diffusion-controlled adsorption model using parameters obtained from equilibrium surface tension. It was shown at short adsorption time that molecules were really adsorbed onto the surface in a diffusion-controlled manner. At a comparably long adsorption time, the ratios (Deff/D) were calculated by assuming the selective adsorption onto the surface. The modified Arrhenius-type equation was proposed by putting a concentration term in front of the exponential terms. The modified Arrhenius-type equation gave Ea=30 kJ/mole for this system. Ea directly derived without an Arrhenius plot was between 9 to 11 kJ/mole. It was an indication that the activation energy alone was not enough to explain the decay of dynamic surface tensions.     

Characterization of Titania/Silica Gel by Means of Low-Pressure Nitrogen Adsorption

Adsorbents synthesized by grafting of titania onto mesoporous silica gel surfaces at different temperatures were studied by means of nitrogen adsorption–desorption and water desorption. The pore size distribution f(R_p) of titania/silica gel depends on the titania concentration (C_TiO2) and the temperature of titania synthesis. Nonuniformity of TiO₂ phase is maximal at a low C_TiO2 value (3.2 wt.% anatase deposited at 473 K), and two peaks of the fractal dimension distribution f(D) are observed at such a concentration of titania, but at larger C_TiO2 values, only one f(D) peak is seen. More ordered filling of pores and adsorption sites by nitrogen, reflecting in the shape of adsorption energy distributions f(E) at different pressures of adsorbate, is observed for adsorbent with titania (rutile+anatase) grafted on silica gel at a higher temperature (673 K).     

Surfactant effects on the spectrophotometry of the gadolinium—chrome azurols complex

Increased molar absorptivities and red-shifted absorbance maxima were noted only upon the addition of cetylpyridinium chloride (CPC), a cationic surfactant. A 1:2:4 gadolinium/chrome azurol S/CPC complex was forned but dissociated at [CPC]/ [Gd³⁺] > 4 apparently because gadolinim(III) was displaced from this complex by additional surfactant monomers. Ternary complexes having different stoichiometries formed in the presence of excess dye. Sodium dodecyl sulfate (SDS), an anionic suffactant, induced dissociation of the binary complex at micellar concentrations, suggesting that dissociation resulted from adsorption of Gd³⁺ cations on the negatively charged micellar surface. Addition of Triton X-100, a nonionic surfactant, had little effect at either micellar or submicellar concentrations. These results confirm that complex stability is an important factor in the use of surfactants as sensitizers in quantitative spectrophotometry.     

Preparation and Characterization of Ceramic Hollow Microspheres for Heavy Metal Ion Removal in Wastewater

Ceramic hollow microspheres (CHMSs) were prepared to use as supports for the removal of heavy metal ions from industrial waste-water. A water extraction sol–gel technique was used to prepare porous CHMS by extracting water from an emulsion of LUDOX (silica colloid; SiO₂, Aldrich Co.) and 2-ethyl-1-hexanol. Experiments were conducted to control pore size, wall thickness, and separation yield by examining the ratio of precursors (LUDOX and 2-ethyl-1-hexanol), catalyst (NH₄OH), sintering temperature, surfactant (SPAN 80), extractant (n-butanol), stirring speed, and concentration of precursor (LUDOX). The results revealed that the optimum conditions were 20 ml of a 10 wt% solution of LUDOX, 10 ml of NH₄OH, a sintering temperature of 500°C, 0.4 ml of SPAN 80, 200 ml of n-butanol, and a stirring speed of 730 rpm/100 ml of 2-ethyl-1-hexanol. CHMSs were impregnated in Cyanex 272 and examined for their ability to remove heavy metal ions from a solution. Based on an experiment involving the removal of metal ions using CHMSs that were prepared under optimum conditions, Zn ion was removed at a level of 0.354 mmol/g at pH 4, which was about twice the adsorption capacity of CHMSs prepared by Wilcox (Mater. Res. Soc. Symp. Proc.346, 201 (1994)).     

Highly Dispersed X/SiO(2) and C/X/SiO(2) (X=Alumina, Titania, Alumina/Titania) in the Gas and Liquid Media

Fumed oxides, such as silica, alumina, titania, and mixed X/silicas (X=Al₂O₃ (AS), TiO₂ (TS), CVD-TiO₂, Al₂O₃/TiO₂ (AST)), pristine or covered by carbon deposits formed due to pyrolysis of cyclohexene, were studied using nitrogen adsorption–desorption, photon correlation spectroscopy particle sizing, and electrophoresis. A significant influence of the nature of surface-active sites and structural features of oxides (individual silica, mixed fumed, or prepared using chemical vapor deposition (CVD)) on the pyrolysis of cyclohexene is observed with respect to the pore size distributions due to differences between primary particles in aggregates and on their outer surfaces in the filling of channels by pyrocarbon, resulting also in a decrease in fractal dimension. Structural characteristics and dependences of the particle size distribution and electrokinetic potential of X/SiO₂ and C/X/SiO₂ on the pH of aqueous suspensions suggest that the carbon deposit covers mainly acidic sites at the X/SiO₂ interfaces and X phase patches possessing catalytic activity in pyrolysis, as the negative charge of particles is reduced by pyrocarbon grafting.     

Cetylpyridinium chloride micelles as a selective fluorescence quenching solvent media for discriminating between alternant versus nonalternant polycyclic aromatic hydrocarbons

Fluorescence behavior of 41 polycyclic aromatic hydrocarbons (PAHs) dissolved in aqueous micellar cetyltrimethylammonium chloride (CTAC) solvent media and in five different cetyltrimethylammonium chloride + cetylpyridinium chloride (CPC) surfactant mixtures is reported. Experimental fluorescence measurements reveal that CPC is a selective fluorescence quenching agent for alternant PAHs. The cetylpyridinium ion effectively quenched emission intensities of the 21 alternant PAHs studied. Emission intensities of nonalternant PAHs, with a few noted exceptions, were unaffected by the presence of CPC in the mixed cationic surfactant micelles.     

Effect of pore structure on surface characteristics of zirconium phosphate-modified silica

Three samples of silica of different pore structure-predominantly microporous, S1; mesoporous, S2; and nonporous, S3-were modified with zirconium phosphate and examined. Pore structure analysis showed that modification had taken place in wider pores of S1 leaving a totally microporous sample, and in large pores of S2 giving a mesoporous sample of narrower pore size distribution. The modification of the nonporous sample decreased the surface area and pore volume to a lower extent than in the other two samples, but resulted in a surface of lower energy toward N2. The different distribution of surface silanol groups on the surfaces of different porosity may result in variable pictures on the modified surfaces as reflected in the differences observed in Br?nsted acidity of modified surfaces. The use of these modified silica samples for amino acid adsorption (L-glutamic acid and L-alanine) indicated that both the isoelectric point of the amino acid and the distribution of surface groups on modified solids are controlling the adsorption process.     

Electroosmotic Flow of a General Electrolyte Solution through a Fibrous Medium

Although hydrotropy is extensively used in industry, the molecular mechanism of hydrotropic solubilization has not been completely elucidated yet. In this paper the interaction between a nonionic surfactant (ethoxylated fatty alcohol containing between five and six oxyethylenic units) and sodium p-toluene sulfonate is examined. Surface tension measurements confirm that the hydrotropic effect occurs at a concentration in which the hydrotropes self-associate. Photon correlation spectroscopy studies show that for this concentration of hydrotropes a drastic reduction in the surfactant micellar radius occurs. Furthermore the luminescence of the hydrotrope used as a fluorescence probe indicates that at low concentrations p-toluene sulfonate dissolves in the surfactant micelles but beyond the minimum concentration for hydrotropic solubilization the hydrotrope is present in the aqueous phase. These results suggest that the hydrotropic effect is related to alterations in the water structure induced by the hydrotrope molecules and to the presence of hydrotrope aggregates that furnish an appropriate niche for the surfactant amphiphile.     

Accounting for diffuse layer ions in triple-layer models

The triple-layer model is one of the most widely used surface complexation models for adsorption on mineral surfaces. In current implementations, the accounting of ions in the diffuse layer may be neglected, resulting in a charge imbalance in the modeled solution as well as errors in mass balance, particularly in low ionic strength solutions when mineral-specific surface area is large. This paper introduces an internally consistent scheme for modeling diffuse layer ions in the triple-layer model. Model calculations illustrate the difference between the proposed and previous implementations using an idealized example. The guarantee of charge balance on both sides of the interface assures that pH is accurately modeled. This may be important in reactive transport simulations, such as modeling adsorption in low ionic strength variable charge soil solutions.     

H(2)O Outgassing Properties of Fumed and Precipitated Silica Particles by Temperature-Programmed Desorption

Temperature-programmed desorption was performed at temperatures up to 850 K on as-received fumed and precipitated silica particles. Physisorbed water molecules on both types of silica had activation energies in the range of 38–61 kJ/mol. However, the activation energies of desorption for chemisorbed water varied from 80 to >247 kJ/mol for fumed silica, Cab-O-Sil-M-7D, and 96 to 155 kJ/mol for precipitated silica, Hi-Sil-233. Our results suggest that physisorbed water can be effectively pumped away at room temperature (or preferably at 320 K) in a matter of hours. Chemisorbed water with high activation energies of desorption (>126 kJ/mol) will not escape silica surfaces in 100 years even at 320 K, while a significant amount of the chemisorbed water with medium activation energies (80–109 kJ/mol) will leave the silica surfaces in that time span. Most of the chemisorbed water with activation energies <126 kJ/mol can be pumped away in a matter of days in a good vacuum environment at 500 K. We had previously measured about 0.1–0.4 wt% of water in silica-reinforced polysiloxane formulations containing 21% Cab-O-Sil-M-7D and 4% Hi-Sil-233. Comparing present results with these formulations, we conclude that the adsorbed H₂O and the Si–OH bonds on the silica surfaces are the major contributors to water outgassing from these types of silica-filled polymers.     

BULK AND INTERFACIAL BEHAVIORS OF MIXED SYSTEM OF HEXADECYLPYRIDINIUM CHLORIDE AND Na+ 2-HYDROXY BENZOATE−

The micellization behavior of hexadecylpyridinium chloride usually called cetylpyridinium chloride (CPC) in presence of sodium salicylate ( NaSal) has been investigated. The surface tension, conductance and microcalorimetric methods have been employed to determine the critical micellar concentration (CMC) of CPC and NaSal mixed in different molar proportions. The interfacial area occupied by CPC in presence of NaSal, the free energy of adsorption and the energetics of micellizatton have been evaluated. The enthalpy of interaction of NaSal with CPC micelle has also been estimated from microcalorimetric measurements. The shear viscosity of the CPC-NaSal combination at equimolar proportion at different surfactant concentration and temperature, and also the shear viscosity of CPC-NaSal combination at different molarity ratios with a fixed surfactant concentration have been determined. The static and dynamic light scattering measurements of the CPC-NaSal system at different composition and in presence of NaCl have been reported. Worm-like micelles of concentration dependent dimension and intermicellar repulsive interaction have been envisaged.     

Transport of Water and Ions Through a Clay Membrane

A model for hindered transport of water and ions is used to predict transient flow through a clay membrane caused by an initial difference in the concentration of salt solutions in reservoirs on the two sides of the membrane. Transport is assumed to be controlled by three coefficients, which are analogous to the permeability, salt diffusivity, and salt reflection coefficient of the membrane. Initial fluid motion is caused by osmosis, leading to a buildup of pressure on one side of the membrane. However, the clay forms an imperfect ion exclusion membrane and the final steady state is one of equal concentrations and pressures on the two sides of the membrane. The time-dependent differences in pressure and salt concentration across the membrane are predicted to vary as the sum of two decaying exponentials. When the salt reflection coefficient is small, one time scale governs Darcy flow through the membrane and another the diffusion of salt. Experimental results confirm the analysis. Although the salt concentration in the reservoirs was monitored in the experiments, estimates of the transport coefficients can be obtained by measuring only the pressure change across the membrane.     

Influence of stereoregularity of the polymer chain on interactions with surfactants: binding of cetylpyridinium chloride by isotactic and atactic poly(methacrylic acid)

Association of a cationic surfactant cetylpyridinium chloride, CPC, with isotactic and atactic poly(methacrylic acid), i-PMA and a-PMA, respectively, in aqueous 0.01 M NaCl solutions was studied by pH and fluorescence measurements in conjunction with potentiometric studies using a surfactant-sensitive membrane electrode. pH measurements have demonstrated that the presence of an oppositely charged surfactant increases ionization of carboxyl groups on PMA at low degrees of neutralization. The increase is more pronounced in the case of i-PMA. The isotactic form of PMA is not soluble in water at zero degrees of neutralization but can be rendered soluble by the addition of CPC at the surfactant to a polyion molar ratio of around 0.4. In the solubilized complex, the positive charge of the CPC molecule is facing the polar solvent, whereas surfactant tails are oriented toward the i-PMA compact coil. Binding isotherms and cooperativity parameters show that chain tacticity has an important influence on the interaction of cetylpyridinium cation with polymethacrylate anion. At the onset of cooperative binding, the association is stronger with i-PMA than with the atactic form, as demonstrated by lower CAC values and higher values of the cooperativity parameters. In contrast, more surfactant is bound by a-PMA in the region where polyion becomes saturated with surfactant ions. Results are interpreted by taking into account local chain conformations as obtained from quantum mechanical semiempirical molecular orbital calculations. Greater hydrophobicity and possibly higher charge density of i-PMA on one hand and more flexibility of the a-PMA chain on the other are held responsible for these observations.     

Simple and specific method for flow injection analysis determination of cationic surfactants in environmental and commodity samples

A new, simple, rapid and specific flow injection analysis (FIA) procedure for the determination of cationic surfactants (CS) i.e. dodecyltrimethylammonium bromide (DTAB), tetradecyltrimethyl-ammonium bromide (TTAB), cetyltrimethylammonium bromide (CTAB), cetylpyridinium chloride (CPC) in the environmental and commodity samples is proposed. Their determinations are based on the enhancement of colour intensity of the Fe(III)-SCN(-) complex. The value of apparent molar absorptivity of the Fe(III)-SCN(-)-CS(+) complexes in the terms of CS lie in the range of (2.10-4.30)x10(3) l mol(-1) cm(-1) at absorption maximum 475 nm. The most sensitive surfactant, cetylpyridinium chloride (CPC) imparted detection limit (absorbance >3 s) of 250 ppb CPC has been selected for the detailed studies. The working range is linear over 0.5-30.0 ppm CPC with slope, intercept, correlation coefficient and sample throughput of 0.67, 0.02, +0.99 and 100 samples h(-1), respectively. The effect of analytical and FIA variables on the determination of the surfactant and the composition of the complex are discussed. The method is free from interferences of almost all ions which commonly associated with the surfactant in the environmental samples. The analytical potentiality i.e. sensitivity, linearity, precision and optimal analytical conditions of FIA to the manual system for the determination of the surfactant are compared. It is reproducibly applicable for the analysis of CS to the various environmental i.e. ground, surface, municipal waste water, and commodity i.e. detergent, soap, shampoo samples.