共查询到20条相似文献,搜索用时 15 毫秒
1.
《先进技术聚合物》2018,29(7):2080-2090
Bio‐based epoxy resins were synthesized from nonedible resources like linseed oil and castor oil. Both the oils were epoxidized through in situ method and characterized via Fourier transform infrared and 1H‐NMR. These epoxidized oils were crosslinked with citric acid without using any catalyst and their properties compared with diglycidyl ether of bisphenol A‐epoxy. The tensile strength and modulus of epoxidized linseed oil (ELO) were found to be more than those of epoxidized castor oil (ECO)‐based network. However, elongation at break of ECO was significantly higher than that of both ELO and epoxy, which reveals its improved flexibility and toughened nature. Thermogravimetric analysis revealed that the thermal degradation of ELO‐based network is similar to that of petro‐based epoxy. Dynamic mechanical analysis revealed moderate storage modulus and broader loss tangent curve of bio‐based epoxies confirming superior damping properties. Bioepoxies exhibit nearly similar contact angle as epoxy and display good chemical resistant. The preparation method does not involve the use of any toxic catalyst and more hazardous solvents, thus being eco‐friendly. 相似文献
2.
A novel bioresin, epoxidized soybean oil was synthesized by in situ method and was characterized employing FTIR and NMR. The bioresin was blended with epoxy(DGEBA) at different ratios as reactive diluents for improved processibility and toughened nature. The composition with 20 wt% bioresin exhibited improved impact strength to the tune of 60% as compared to virgin epoxy. Fracture toughness parameters critical stress intensity factor(KIC) and critical strain energy release rate(GIC) were evaluated using single edge notch bending test and demonstrated superior enhancement in toughness. Dynamic mechanical, thermal, thermo mechanical and fracture morphological analyses have been studied for bio-based epoxy blends. Curing kinetics has been evaluated through DSC analysis to investigate the effect of bioresin on cross-linking reaction of neat epoxy with triethylenetetramine as curing agent. 相似文献
3.
Based on bio‐based furfural, a phosphorus‐containing curing agent (FPD) was successfully synthesized, via the addition reaction between 9,10‐dihydro‐9‐oxa‐10 phosphaphenanthrene‐10‐oxide (DOPO) and furfural‐derived Schiff base. Then, as co‐curing agent, FPD was used to prepare flame retardant epoxy thermosets (EP) cured by 4, 4′‐diaminodiphenyl methane. The incorporated FPD improved the flame retardancy and toughness of epoxy thermoset, simultaneously. When 5 wt% FPD was added into EP, the FPD/EP achieved 35.7% limited oxygen index (LOI) value and passed UL94 V‐0 rating, meanwhile. In FPD/EP thermoset, the incorporated FPD reduced the thermal decomposition rate, increased the charring capacity, and inhibited the combustion intensity of epoxy thermoset. Through gas‐phase and condensed‐phase actions in weakening fuel supply, suppressing volatile combustion, and enhancing charring barrier effect, FPD decreased the heat release of burning epoxy thermoset, significantly. For the outstanding effectiveness on both flame retardancy and toughness, the study on FPD provides a promising way to manufacture high‐performance epoxy thermoset. 相似文献
4.
Charlotte Menager Nathanaël Guigo Luc Vincent Nicolas Sbirrazzuoli 《Journal of polymer science. Part A, Polymer chemistry》2020,58(12):1717-1727
The curing of epoxidized linseed oil (ELO) with three different bio-based dicarboxylic acids (sebacic acid, suberic acid, and succinic acid) has been investigated. No accelerators or catalysts were used and the resulting thermosets are 100% bio-based. Structural investigations of the three crosslinked ELO resins were made using FTIR spectroscopy and TMA, that is, tensile tests, TGA, and DMA. As evidenced by FTIR measurements ELO and dicarboxylic acids reacts but no major differences can be distinguished between the dicarboxylic acids. Non-isothermal curing has been conducted by rheological and DSC measurements. Advanced isoconversional analysis applied to DSC data in association with the complex viscosity variations gives new insights into the polymerization mechanism. The length of dicarboxylic acid carbon chain modifies the reaction rate. Then, a correlation between reaction rate, activation energy, pre-exponential factors, polymerization mechanism, and change in rate-limiting step was shown. DMA and tensile tests highlight the relationship between the carbon chain length, reactivity, and thermomechanical properties. The use of succinic acid allows reaching a higher Tg and thermal stability. 相似文献
5.
《先进技术聚合物》2018,29(1):160-170
A trifunctional epoxy resin from itaconic acid (TEIA) was synthesized from a renewable resource‐based itaconic acid by allylation of itaconic acid to form diallyl itaconate by using m‐chloroperoxybenzoic acid as oxidizing agents followed by epoxidation of allylic C═C bond of diallyl itaconate methylhexahydropthalic anhydride as curing agent in the presence of 2‐methyl imidazole as a catalyst. The chemical structure of the synthesized resins was confirmed by Fourier transform infrared and nuclear magnetic resonance (1H‐NMR and 13C‐NMR) spectroscopy analysis. The mechanical, thermal, and rheological performances of the TEIA were also investigated and compared with diglycidyl ether of bisphenol A and a plant‐based epoxidized soybean oil bioresin cured with the same curing agent. The higher epoxy value of 1.02, lower viscosity (0.96 Pa s at 25°C), higher mechanical, and higher curing reactivity toward methylhexahydropthalic anhydride of TEIA as compared with epoxidized soybean oil and comparable with diglycidyl ether of bisphenol A demonstrated significant evidence to design and develop a novel bio‐based epoxy resin with high performance to substitute the petroleum‐based epoxy resin. 相似文献
6.
The influence of reactive organoclay on a biorenewable castor oil‐based polyurethane prepolymers toughened polylactide nanocomposites 下载免费PDF全文
Polylactide (PLA) is the most extensively reviewed and utilized biodegradable and renewable thermoplastic polyester, with potential to replace conventional petroleum‐based polymeric materials. To improve the toughness of PLA, castor oil‐based polyurethane prepolymer (COPUP) toughened PLA nanocomposites were prepared via the melt mixing process and investigated for its mechanical, thermal and morphological properties. X‐ray diffraction and transmission electron microscopy studies revealed the formation of polymer blend nanocomposites. Mechanical tests revealed optimum performance characteristics at PLA/COPUP ratio of 70:30. Further, loading of the organoclay showed higher tensile strength and modulus of the blend nanocomposites as compared to optimized blend. The morphological results indicated that the surface roughness increases as a function of the organoclay incorporation. Thermogravimetric measurements reveal that the thermal stability of the blend increases with the incorporation of organoclay. The improved mechanical properties along with its biodegradability might lead to new industrial and biomedical applications. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
7.
As new bio‐based epoxy resin systems, glycerol polyglycidyl ether (GPE) and sorbitol polyglycidyl ether (SPE) were cured with tannic acid (TA) at various conditions. When the curing conditions were optimized for the improvement of thermal and mechanical properties, the most balanced properties were obtained for the GPE/TA and SPE/TA cured at 160 °C for 2–3 h at the epoxy/hydroxyl ratio of 1/1. The cured SPE/TA had a higher glass transition temperature (Tg) and tensile strength than the cured GPE/TA. Next, biocomposites of GPE/TA and SPE/TA with microfibrillated cellulose (MFC) were prepared by mixing aqueous solution of the epoxy/curing reagent with MFC, and subsequent drying and curing at the optimized condition. For both the GPE/TA/MFC and SPE/TA/MFC biocomposites, Tg and the storage modulus at rubbery plateau region increased with increasing MFC content over the studied range of 3–15 wt %. The tensile strength at 25 °C for GPE/TA/MFC biocomposite with MFC content 10 wt % was 76% higher than that of control GPE/TA, while the tensile modulus was little improved. On the other hand, the tensile strength and modulus of SPE/TA/MFC biocomposite with MFC content 10 wt % were 30 and 55% higher than those of control SPE/TA, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 425–433, 2010 相似文献
8.
Mitsuhiro Shibata Naozumi Teramoto Yoshihiro Someya Sakuya Suzuki 《Journal of Polymer Science.Polymer Physics》2009,47(7):669-673
A mixture of epoxidized soybean oil (ESO), (R)‐12‐hydroxystrearic acid (HSA) and a photoinitiator for cationic polymerization in the ESO/HSA weight ratio 10/1 was heated to 100 °C and gradually cooled to room temperature to give bio‐based gelatinous material. The photo‐curing of the gel afforded a nanocomposite composed of crosslinked ESO and supramolecular HSA nanofibers. The transmission electron microscopy observation of the photo‐cured ESO/HSA revealed that dendritic clusters of HSA nanofibers are formed in the crosslinked ESO matrix. In the differential scanning calorimetry chart of the ESO/HSA, a thermal transition from the mesophase composed of supramolecular nanofibers to isotropic state was observed at 67 °C (ΔH = 22.6 J/g‐HSA), while the Tm of crystalline HSA is 77.7 °C (ΔHm = 159 J/g‐HSA). Tensile strength at 20 °C of the ESO‐HSA was ~80% higher than that of photo‐cured ESO without HSA. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 669–673, 2009 相似文献
9.
Flame retardants from vanillin when utilized together with ammonium polyphosphate (APP) yield excellent synergistic flame retardancy toward epoxy resins. Bisphenol A epoxy resins have been widely used due to their excellent mechanical properties, chemical resistance, electrical properties, adhesion, etc., while they are flammable. Environment‐friendly and bio‐based flame retardants have captured increasing attention due to their ecological necessity. In this paper, 3 bio‐based flame retardants were synthesized from abundant and more importantly renewable vanillin, and their chemical structures were determined by 1H NMR and 13C NMR. They were used together with APP (an environment‐friendly commercial flame retardant) to improve the fire resistance of bisphenol A epoxy resin. With the addition APP content of 15 phr, the modified bisphenol A epoxy resin could reach UL‐94V0 rating during vertical burning test and limit oxygen index values of above 35%, but reducing APP content to 10 phr, the flame retardancy became very poor. With the total addition content of 10 phr, the epoxy resins modified by 7 to 9 phr APP and 1 to 3 phr bio‐based flame retardants with epoxy groups or more benzene rings showed excellent flame retardancy with UL‐94V0 rating and limit oxygen index values of around 29%. The Tgs of the epoxy resins could be remained or even increased after introducing bio‐based flame retardants, as the control; those of APP alone‐modified epoxy resins compromised a lot. The green synergistic flame‐retardant systems have a great potential to be used in high‐performance materials. 相似文献
10.
G. Lligadas J. C. Ronda M. Gali V. Cdiz 《Journal of polymer science. Part A, Polymer chemistry》2006,44(23):6717-6727
Novel biobased epoxy resins were prepared from two fatty acid derivatives; epoxidized 10‐undecenoyl triglyceride and epoxidized methyl 3,4,5‐tris(10‐undecenoyloxy)benzoate, with 4,4′‐diaminodiphenylmethane as a crosslinking agent. The flame retardancy of these epoxy resins was improved by the addition of 10‐[2′, 5′‐bis(9‐oxiranyl‐nonayloxy)phenyl]‐9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide and by crosslinking with a phosphorus‐containing curing agent, bis(m‐aminophenyl)methylphosphine oxide. The thermal, thermomechanical, and flame‐retardant properties of the cured materials were measured with differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, and the limiting oxygen index. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6717–6727, 2006 相似文献
11.
Methylimidazole‐terminated chain‐extended urea (MITU) containing polypropylene oxide spacer was synthesized and employed to modify epoxies composed of a diglycidyl ether of bisphenol‐A (E‐51) and methyltetrahydrophthalic anhydride (MTHPA). The curing behavior, viscoelastic property, impact response, and fracture surface morphology of the curing systems were systematically investigated. Differential scanning calorimeter (DSC) analysis reveals that the curing reactivity of the epoxy system is greatly enhanced with the addition of MITU. From the dynamic mechanical analysis, besides the low‐temperature β relaxation, shoulder at higher temperature side appears for the MITU‐modified systems. Meanwhile, the addition of MITU leads to the increase of loss factor (tan δ) over the temperature range of 0–75°C. Impact tests show that the modifier can be effective in toughening the epoxy resin at relatively low loading, and the scanning electron microscope (SEM) images of the fracture surface for the modified systems display signs of ductility. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
12.
《先进技术聚合物》2018,29(6):1852-1860
A novel kind of biobased monomer, epoxidized cardanol‐based acrylate (ECA), was successfully synthesized from cardanol via acrylation and epoxidization. The chemical structure was confirmed by Fourier transform infrared spectroscopy and proton nuclear magnetic resonance. Then, the ECA was employed to produce UV‐curable films and coatings copolymerized with castor oil‐based polyurethane acrylate. Compared to coatings from petroleum‐based diluent hydroxyethyl acrylate‐based castor oil‐based polyurethane acrylate resins, ECA‐based biomaterials exhibited a little inferior dilution ability but overcome the drawback of high volumetric shrinkage with a special lower value. Moreover, ultimate properties of the UV‐cured biomaterials such as thermal, mechanical, coating, swelling, and hydrophobic properties were investigated. The UV‐curing behavior was investigated using real‐time IR, and the overall double bond conversion was more than 90%. This biobased UV‐curable cardanol‐based diluent shows a promise in “green + green” materials technologies. 相似文献
13.
Bio‐oils, produced by biomass pyrolysis, have become promising candidates for feedstocks of high value‐added chemicals and alternative sources for transportation fuels. Bio‐oil is such a complicated mixture that contains nonpolar hydrocarbons and polar components which cover almost all kinds of organic oxygenated compounds such as carboxylic acids, alcohols, aldehydes, ketones, esters, furfurals, phenolic compounds, sugar‐like material, and lignin‐derived compounds. Comprehensive characterization of bio‐oil and its subfractions could provide insight into the conversion process of biomass processing, as well as its further utilization as transportation fuels or chemical raw materials. This review focuses on advanced analytical strategies on in‐depth characterization of bio‐oil, which is concerned with gas chromatography, high‐resolution mass spectrometry, FTIR spectroscopy and NMR spectroscopy, offering complementary information for previous reviews. 相似文献
14.
Niloufar Ghasemi Rad Zeinab Karami Mohammad Jalal Zohuriaan‐Mehr Ali Salimi Kourosh Kabiri 《先进技术聚合物》2019,30(9):2361-2369
Two kinds of bio‐resourced reactive diluents have been synthesized from linseed oil. The prepared epoxidized linseed oil (ELO) and the cyclocarbonated linseed oil (CLO) were separately blended with a petroleum‐based tetra‐functional epoxy resin (TGDDM) to improve its processability and to overcome the brittleness of the thermoset network therefrom. The linseed oil modifications were spectrally established, and processability improvement of the resin blends was rheologically confirmed. The curing of samples was studied by differential scanning calorimetry, and their mechanical properties (ie, tensile, flexural, fracture toughness, and adhesion) were investigated as well. Scanning electron microscopy images were obtained to reconfirm the toughness improvement of the modified thermosets. In contrast of the epoxidized soybean oil (ie, the most conventionally studied bio‐based reactive diluent), ELO and CLO had no negative effects on the thermoset material characteristics. They improved properties such as tensile strength (up to 43.2 MPa), fracture toughness (1.1 MPa m1/2), and peel‐adhesion strength (4.5 N/25 mm). It was concluded that ELO and CLO were efficient reactive diluents to be used in formulations of polymer composites, surface coatings, and structural adhesives based on epoxy resins. 相似文献
15.
Krishnadevi Krishnamoorthy Devaraju Subramani Naveena Eeda Alagar Muthukaruppan 《先进技术聚合物》2019,30(7):1856-1864
In the present work, new classes of bio‐based polybenzoxazines were synthesized using eugenol as phenol source and furfurylamine and stearylamine as amine sources separately through solventless green synthetic process routes and were further reinforced with varying percentages (1, 3, 5, and 10 wt%) of silica (from rice husk) to attain hybrid composites. The molecular structure, cure behaviour, thermal stability, dielectric properties, and flame‐retardant behaviour of both benzoxazine monomers and benzoxazine composites were characterized using appropriate modern analytical techniques. The eugenol‐based benzoxazines synthesized using furfurylamine (FBz) and stearylamine (SBz) were cured at 223°C and 233°C, respectively. The differential scanning calorimetry (DSC) data reveal the glass transition temperatures (Tg) of FBz and SBz were 157°C and 132°C, respectively, and the maximum decomposition temperature (Tmax) as obtained from thermogravimetric analysis (TGA), were found to be 464°C and 398°C for FBz and SBz, respectively. The dielectric constants for FBz and SBz obtained at 1 MHz were 3.28 and 3.62, respectively. Furthermore, varying weight percentages (1, 3, 5, and 10 wt%) of 3‐mercaptopropyltrimethoxysilane (3‐MPTMS) functionalized bio‐silica reinforced the composite materials as evidenced by their improved thermal stability and lower dielectric constant. Data obtained from thermal and dielectric studies suggested that these polybenzoxazines could be used in the form of adhesives, sealants, and composites for high performance inter‐layer low‐k dielectric applications in microelectronics. 相似文献
16.
Alaleh Dabbaghi Kourosh Kabiri Ali Ramazani Mohammad J. Zohuriaan‐Mehr Arash Jahandideh 《先进技术聚合物》2019,30(11):2894-2905
Recent researches focus on the synthesis of new cross‐linkers from natural resources. In the current work, functionalized tannic acid was employed as a replacement of petroleum‐based cross‐linkers because of its outstanding biochemical properties. Alkene‐ and epoxy‐functionalized tannic acids were synthesized as internal and external cross‐linkers, respectively. Cross‐linker structures were characterized with Ft‐IR and 1HNMR analysis. Different amounts, as well as different numbers of alkene functional group, were incorporated during the superabsorbent synthesis. Moreover, the internal cross‐linked superabsorbent was surface cross‐linked with different amounts of epoxy‐functionalized tannic acid and increased the absorbency under load about 10 g g?1. Free absorption properties in water and saline solution, absorbency under load, and rheological properties of superabsorbents were investigated. In addition, the antibacterial activity of the internal and external cross‐linked superabsorbent was studied against Escherichia coli and Staphylococcus aureus bacteria via different methods and compared with that of conventional superabsorbent. 相似文献
17.
Chun Hua Zhao Shun Jiang Wan Lu Wang Xiang Dong Liu Takeshi Endo 《Journal of polymer science. Part A, Polymer chemistry》2014,52(3):375-382
This study investigates the curing of epoxidized soybean oil (ESO) using dicyandiamide (DICY) and combinations of DICY with several accelerators as curing agents. The differential scanning calorimetry (DSC) results indicated that carbonyldiimidazole (CDI) is a highly efficient accelerator for the ESO‐DICY curing system. CDI accelerated ESO‐DICY curing system can gel within a short period of 13 min at 190 °C. The activation energies of the ESO‐DICY curing systems with and without CDI are 95 and 121 kJ mol?1, respectively. Similar acceleration effect was observed in the ESO‐diglycidyl ether of biphenyl A (DGEBA) blending formulations. When the molar part of the glycidyl epoxy groups of DGEBA was equal to the internal epoxy groups of ESO in the mixture, gelation of the DICY curing system accelerated by CDI was achieved in 3 min at 160 °C. Furthermore, the DSC results with FTIR analysis suggest that the stoichiometric curing molar ratio was 3 ESO epoxy units per 1 DICY molecule. Two epoxy units reacted with DICY to give secondary alcohols, while the other one linked to the nitrile group. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 375–382 相似文献
18.
《先进技术聚合物》2018,29(6):1744-1752
A series of hybrid systems which combine double‐functionalized linseed oil (methacrylated epoxidized linseed oil) and 2 types of functionalized halloysite (methacrylated halloysite and epoxidized halloysite) was designed in the current study. The curing of the new formulated oil‐clay mixtures was performed via 2 different mechanisms under the influence of the temperature: free‐radical and anionic polymerization. The effect of the functionalized clay tubes against the oil‐based macromonomer reactivity, representing the focus of this study, was monitored by differential scanning calorimetry and Fourier transform infrared spectrometry, concluding that both types of halloysite nanotubes (HNTs) exhibit significant influence on the building of methacrylate/epoxy networks. The effect of the HNTs on the methacrylated epoxidized linseed oil network properties was studied by dynamic mechanical analysis and thermogravimetric analysis, and the morphology of the synthesized hybrids was investigated by scanning electron microscopy. The results suggested that the designed oil‐based hybrid performance is determined by the presence of the both HNT molecules. 相似文献
19.
CaiFei Wang ChunHua Zhao JiaQin Sun SanQing Huang XiangDong Liu Takeshi Endo 《Journal of polymer science. Part A, Polymer chemistry》2013,51(9):2016-2023
A fully bio‐based benzoxazine, 3‐furfuryl‐8‐methoxy‐3,4‐dihydro‐2H‐1,3‐benzoxazine (Bzf), has been prepared using guaiacol, furfurylamine, and paraformaldehyde as raw materials. Its chemical structure has been characterized by 1H and 13C NMR, FTIR, and elemental analysis. The polymerization behavior of Bzf in the presence of methyl p‐toluenesulfonate (PTSM) has been studied by FTIR and DSC, and the thermal stability of the cured resin has been evaluated by thermogravimetric analysis. It was found that PTSM is a good promoter that serves to avoid thermal decomposition of the bio‐based monomer during the curing process at high temperature. In contrast to the situation with neat Bzf, the presence of PTSM (5 mol % for Bzf) significantly improves the polymerization behaviors, including a decrease in the polymerization temperature from 240 to 174 °C, a shortening of the time required to reach the gel point on heating at 200 °C from 47 to 20 min, and an increase in the char yield of the cured resin from 53 to 62%. Moreover, these observed experimental results on the promoting effect of PTSM are interpreted in terms of several possible mechanistic schemes, which involve a catalytic effect on the dissociation of C? O bonds in both the coordination ring‐opening reaction and the rearrangement from a phenoxy structure to a phenolic structure. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013 相似文献
20.
Hisatoyo Morinaga Natsumi Ogawa Mayu Sakamoto Hiroshi Morikawa 《Journal of polymer science. Part A, Polymer chemistry》2019,57(24):2466-2473
The thiol‐ene reaction between trans‐limonene oxide (trans‐LO) and ethane‐1,2‐dithiol in the presence of triethylborane affords a bio‐based bis‐functional epoxide (bis‐trans‐LO). The crosslinking reaction of bis‐trans‐LO with branched polyethyleneimine (BPEI; Mn = 600; BPEI600) at a feed ratio of bis‐trans‐LO/BPEI600 = 57/43 (wt/wt) yields the corresponding network polymer with Td10 (10% thermal decomposition temperature) of 304.7 °C in 98% yield. In contrast, negligible amounts of network polymer are obtained by the reaction of bis‐LO (bis‐functional epoxide derived from cis and trans‐LO) and BPEI600 regardless of the feed ratio. The mechanical strengths as measured by direct tensile tests of the network polymers derived from bis‐trans‐LO and BPEI600,1800 (Mn = 600 and 1800) were approximately 16 and 11 times higher than that of bis‐LO and BPEI1800, respectively. The tensile shear strengths of the metal‐to‐metal adhesive bonds induced by bis‐trans‐LO and BPEI600,1800 were 9.5 and 14.1 MPa, respectively. DMA revealed that the storage modulus of the network polymer derived from bis‐trans‐LO and BPEI1800 in the rubber region was higher than that of the material prepared from bis‐LO and BPEI1800, indicating higher crosslink density of the bis‐trans‐LO/BPEI1800 system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2466–2473 相似文献