The use of inverse gas chromatography to study surface thermal oxidation of polypropylene

Thermo-oxidative effects on the surface energy of polypropylene were measured by inverse gas chromatography as a function of exposure time and temperature. Unaltered polypropylene had a surface energy of 33 mJ/m². Oxidized polypropylene, after exposure to air at temperatures of 100 °C and 110 °C, had a range of maximum surface energies from 38 to 41 mJ/m². Comparisons between FTIR carbonyl peak growth and the surface energy showed that both methods detect oxidation, though the increase in surface energy is detected before the carbonyl peak growth is noticeable. The work of adhesion predicted by the surface free energies obtained in this work between a coated calcium carbonate and polypropylene changes by 10% due to the oxidation of the polymer at 110 °C.     

ESCA study of the surface photo-oxidation of some non-aromatic polymers

Changes in the surface composition and structure of a number of non-aromatic polymers subjected to ultraviolet irradiation in oxygen (～ 1 atm., 20°C) have been studied. No changes in surface composition were detected after photo-oxidation of poly(vinylidene fluoride) (12 h of irradiation), low density polyethylene (7·5 h) or high density polyethylene (22·3 h). This reflects the absence in these polymers of an efficient ultraviolet absorber to initiate the photo-oxidation. The surfaces of poly(methyl methacrylate) and nylon 66 show an increase in oxygen content following irradiation. In these polymers this added oxygen is present principally as carboxyl groups and, in the case of poly(methyl methacrylate), as carbonyl groups. In nylon, there is no evidence for changes in the amide group and no oxidation of the nitrogen is detected.     

Secondary processes of poly(methyl methacrylate) and their activation energies as determined by shear and tensile creep compliance measurements

The results of measurement of the shear and tensile creep compliance of poly(methyl methacrylate) between ?150 and 75°C. are presented. The master curves show the creep behavior from essentially elastic response to the onset of the α-process. The logarithmic retardation spectra and shear loss compliance reveal two molecular processes, one process being partially obscured by the α-process and therefore not as well defined as the other. These processes manifest themselves as breaks in an Arrhenius plot of the shift factors at about ?35 and +25°C. The activation energies in the ?35 to 25°C. and 25 to 80°C. ranges are 17.8 kcal./mole and 42.2 kcal./mole, respectively. The former temperature range and activation energy corresponds to the well-known ß-process in poly(methyl methacrylate), the latter to a process which is apparently detectable using various long-time experimental techniques but whose molecular interpretation is at present obscure. The activation energy in the ?150 to ?35°C. range is about 8.7 kcal./mole.     

Synthesis,characterization, microstructure determination,thermal studies of poly (N-vinyl pyrrolidone-maleic anhydride-methyl methacrylate)

Synthesis of Poly (N-vinyl pyrrolidone-maleic anhydride-methyl methacrylate) terpolymer using azobisisobutyronitrile in 1,4-dioxan is described. The polymers with different composition were synthesized and characterized using FTIR, ¹HNMR, ¹³NMR, TGA and DSC techniques. The monomer-monomer interactions were studied using Finemann-Ross and Kelen-Tudos methods by calculating the reactivity ratio. The reactivity ratio r₁ and r₂ with respect to methyl methacrylate and N-vinylpyrrolidone-maleic anhydride complexomer are found to be 6.05 and 0.06 respectively. The study showed methyl methacrylate have higher reactivity than N-vinyl-2-pyrrolidone-maleic anhydride complex, i.e., the terpolymer contained methyl methacrylate in higher ratio. The thermal stability of poly (N-vinyl pyrrolidone-maleic anhydride-methyl methacrylate) was 165°C and the glass transition temperature was found to increase from 153°C to 182°C as MMA concentration increase. The studies indicate the activity of the polymer to inhibit bacterial growth is very poor.     

A detailed surface analytical study of degradation processes in (meth)acrylic polymers

The present study investigates the degradation behavior of various high‐molecular‐weight acrylic polymers (50,000 < M_n/g mol^?1 < 100,000), namely poly(methyl methacrylate) (PMMA), poly(n‐butyl methacrylate) (PBMA), poly(n‐butyl acrylate) (PBA), and poly(lauryl methacrylate) (PLMA), under extreme environmental conditions. These polymers were synthesized via various polymerization techniques to create different end‐groups. The polymers chosen are readily applicable in the formulation of surface coatings and were degraded under conditions which replicate the harsh Australian climate, where surface coatings may reach temperatures of up to 95 °C and are exposed to broad‐spectrum UV radiation of up to 1 kW m^?2. The degradation behavior of the polymeric materials on their surface was followed via ATR‐IR spectroscopy, high resolution FTIR microscopy, and X‐ray photoelectron spectroscopy. The extent of the observed thermal and photo‐oxidation is directly related to the length of the ester side group, with the degradation susceptibility decreasing in the order of PLMA > PBMA/PBA > PMMA, with PMMA still stable even after 5 months exposure to the harshest condition used (UV light at 95 °C). The general degradation mechanism involves the loss of the ester side groups to form methacrylic acid followed by cross‐linking. The effect of the variable end groups was found to be minimal. The results from this study are in good agreement with previous studies of low‐molecular‐weight model polymers under identical conditions. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Graft Copolymerization of Methyl Methacrylate onto Poly(Ethylene Terephthalate) Fibers Using Benzoyl Peroxide

Abstract

The graft copolymerization of methyl methacrylate onto poly(ethylene terephthalate) fibers has been studied using benzoyl peroxide as initiator. The grafting reactions were carried out within the 70 to 90°C temperature range, and the variations of graft yield with monomer and initiator concentrations were also investigated. The overall activation energy for grafting was calculated as 34.1 kcal/mol. The results of dyeability with the disperse dye suggested that diffusion into the fiber structure was moderately difficult when the graft yield reached 14?15%. The maximum graft yield was obtained at a benzoyl peroxide concentration of 4.00 × 10^?3 M. The decomposition temperature values obtained from thermogravimetric analysis show that the thermal stability of poly(ethylene terephthalate) fibers decreased as a result of grafting. Further, such change in the properties of methyl methacrylate grafted fibers as density, diameter, and moisture regain were also determined.     

Polar anchoring strengths of nematic liquid crystal on high-density polymer brush surfaces

ABSTRACT

Herein, the polar anchoring energy coefficient (A_θ) of nematic liquid crystal (NLC) was examined for high-density polymer brushes via capacitance measurements. The A_θ is 10^?4 J m^?2 for the brushes of poly(methyl methacrylate), poly(ethyl methacrylate) and poly(styrene). The value decreases to 10^?5 J m^?2 for poly(n-butyl methacrylate) and poly(hexyl methacrylate) with lower glass transition temperatures. However, each polymer brush displays a constant A_θ value over a temperature range of ?15°C to 90°C, which is hardly affected by the graft density and brush thickness. At 25°C, A_θ is 10 times greater than the corresponding azimuthal anchoring energy coefficient (A_φ); therefore, NLCs on polymer brushes can be preferentially aligned along the in-plane component of the applied field.     

Synthesis of poly(arylene ethylene) oligomeric hydroperoxides and their use as initiating agents of radical polymerization

The oxidation to hydroperoxide of poly(arylene ethylenes) (PAE) by oxygen carried out in solutions at 80–110°C. The effect of initiating additions and the nature of solvent relative to the content of hydroperoxide groups in oxidized PAE were investigated. The oxidation to hydroperoxides in PAE occurs at the methylene groups, and the synthesized hydroperoxides are secondary peroxides. The decomposition of PAE hydroperoxides in toluene and chlorobenzene at concentrations of 0.006–0.03 mole/l. for hydroperoxide in the presence and absence of N-phenyl-α-naphthylamine (PNA) was studied. The decomposition of one hydroperoxide has been studied in the presence of cobaltous and manganese resinates and of PNA in chlorobenzene at 30–50°C. The addition of PNA to a chlorobenzene solution of PAE hydroperoxide containing cobaltous or manganese resinate accelerates the hydroperoxide decomposition, reduces the activation energy, and changes the reaction order from the second-order to first-order. The synthesized hydroperoxides initiate the radical polymerization of styrene and methyl methacrylate. The initiating activity of one of the synthesized hydroperoxides of PAE for polymerization of styrene (60°C) in the presence and absence of activating addition of manganese resinate was also evaluated.     

Polymerization of methyl methacrylate with ceric ion-methanol redox system

The polymerization of methyl methacrylate initiated by Ce⁴⁺ methanol redox system was studied in aqueous solution of nitric acid at 15°C. The polymerization was initiated by primary radicals formed from Ce⁴⁺/alcohol complex. Poly(methyl methacrylate) chains containing the alcohol residue were obtained. Variations in the temperatuare and concentration of the components of the redox system allowed the control of the rate of polymerization and molecular weight of the polymer. The concentration of the hydroxyl end groups in the poly(methyl methacrylate) of low molecular weight was determined by titration and by spectrometric method.     

Introduction of 2-methoxycarbonylallyl end group by copolymerization of methyl α-(phenoxymethyl)acrylate accompanying with addition-fragmentation reaction

Copolymerizations of methyl α-(phenoxymethyl)acrylate (MPMA) with methyl acrylate, methyl methacrylate, styrene, and methyl α-ethylacrylate were carried out. Addition of a polymer radical to MPMA followed by the subsequent fragmentation of poly(MPMA) radical resulted in the 2-methoxycarbonylallyl end group and phenoxy radical in the course of the copolymerization. The extent of the fragmentation determined by ¹H-NMR spectroscopy depends on reactivity of the MPMA radical toward the reference monomers. An increase in the addition rate of the MPMA radical to the reference monomer brought about suppression of the fragmentation. The addition of the MPMA radical to styrene seems to be sufficiently fast to prevent the fragmentation. Since the rate of the fragmentation relative to the propagation was considerably accelerated by raising the temperature to 110°C, MPMA can be used as a novel chain transfer agent to control molecular weight and end group at a temperature above 100°C. © 1993 John Wiley & Sons, Inc.     

Improvement of the thermal stability of cluster‐crosslinked polystyrene and poly(methyl methacrylate) by optimization of the polymerization conditions

The polymerization conditions for polystyrene and poly(methyl methacrylate) crosslinked by 0.5 mol % of the cluster Zr₆O₄(OH)₄(methacrylate)₁₂ were optimized by applying a step polymerization procedure. The onset of thermal decomposition was thus increased up to about 50° for polystyrene and about 110° for poly(methyl methacrylate). The increase in thermal stability correlated with a higher char yield. The glass transition temperatures were also increased by about 15°. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6586–6591, 2005     

Surface characterization and electrical property of carbon fibers modified by air oxidation

Polyacrylonitrile‐based carbon fibers were modified by oxidation in air, and a systematic study of surface groups and surface resistance at different treated temperatures was made. Progressive fiber weight loss occurred with increasing extents of air oxidation, and it was approximately proportional to the extent of air oxidation from the onset of oxidation up to 400 °C. At this point 4.4% of the initial fiber weight had been lost. A faster loss of weight occurred as the extent of air oxidation increased from 400 °C to 700 °C. X‐ray photoelectron spectroscopy studies (C 1s and O 1s) indicated that the oxygen/carbon atomic ratio rose rapidly from 2.64% (as‐received carbon fiber) to 42.83% as the oxidation temperature was increased to 400 °C. Fourier transform infrared spectra showed the relative intensity of the peaks at about 3440 cm^?1 from ―OH stretching vibrations and at 1634 cm^?1 from ―C?O stretching vibrations increased significantly at 400 °C. FESEM micrographs showed that as‐received fibers show relatively smooth surface. With oxidation temperature increasing, the fiber surface was rougher. The surface resistance of treated carbon fibers decreased obviously with increasing oxidation temperatures. The most decrease was about 100% at 400 °C. Copyright © 2014 John Wiley & Sons, Ltd.     

Atom transfer radical polymerization of styrene and methyl methacrylate catalyzed by FeCl2/iminodiacetic acid

The atom transfer radical polymerization of styrene and methyl methacrylate with FeCl₂/iminodiacetic acid as the catalyst system in bulk was successfully implemented at 70 and 110 °C, respectively. The polymerization was controlled: the molecular weight of the resultant polymer was close to the calculated value, and the molecular weight distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight ∼ 1.5). Block copolymers of polystyrene‐b‐poly(methyl methacrylate) and poly(methyl methacrylate)‐b‐poly(methyl acrylate) were successfully synthesized, confirming the living nature of the polymerization. A small amount of water added to the reaction system increased the reaction rate and did not affect the living nature of the polymerization system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4308–4314, 2000     

Dynamic mechanical and dielectric relaxations of poly(difluorobenzyl methacrylates)

This work reports the mechanical and dielectric relaxation spectra of three difluorinated phenyl isomers of poly(benzyl methacrylate), specifically, poly(2,4‐difluorobenzyl methacrylate), poly(2,5‐difluorobenzyl methacrylate) and poly(2,6‐difluorobenzyl methacrylate). The strength of the dielectric glass–rubber relaxation of the 2,6 difluorinated phenyl isomer is, respectively, nearly three and two times larger than the strengths of the 2,5 and 2,4 isomers. The 2,4 isomer presents a mechanical α peak the intensity of which is nearly two times that of the other two isomers. Both the mechanical and dielectric relaxation spectra display a subglass process, called γ relaxation, centered in the vicinity of −50 °C at 1 Hz and, in some cases, a subglass β absorption is detected at higher temperature partially masked by the glass–rubber relaxation. The mean‐square dipole moments per repeating unit, 〈μ2〉/x, measured at 25 °C in benzene solutions, are 2.5 D², 1.9 D², and 5.0 D² for poly(2,4‐difluorobenzyl methacrylate), poly(2,5‐difluorobenzyl methacrylate) and poly(2,6‐difluorobenzyl methacrylate), respectively. These results, in conjunction with Onsager type equations, permit to conclude that auto and cross‐correlation contributions to the dipolar correlation coefficient may have the same time‐dependence. On the other hand, dipole intermolecular interactions, rather than differences in the flexibility of the chains, seem to be responsible for the relatively high calorimetric glass‐transition temperature of the 2,6 diphenyl isomer, which is, respectively, nearly 36 °C and 32 °C above the T_g's of the 2,4 and 2,5 isomers. Molecular Mechanics calculations give a good account of the differences observed in the polarity of the polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2179–2188, 2000     

Dielectric study of low-temperature relaxations in poly(isobutyl methacrylate), poly(n-butyl methacrylate), poly(isopropyl methacrylate), and poly(4-methylpentene-1)

Isochronal measurements of dielectric constant and loss are made for poly(isobutyl methacrylate) (PiBMA), poly(n-butyl methacrylate) (PnBMA), poly(isopropyl methacrylate) (PiBMA), and poly(4-methylpentene-1) (P4MP1) at temperatures ranging from 4°K to 250°K. Loss peaks are found around 120°K (10–100 Hz) for PiBMA, PnBMA, and P4MP1. By comparing the activation energy with the calculated potential barrier for the internal rotation of alkyl group in the side chain, the motion responsible for the 120°K peak is concluded to be essentially the rotation of the isopropyl group as a whole for PiBMA and P4MP1 but, for PnBMA, the rotation of n-propyl group accompanied by the rotation of the end ethyl group. Multiple paths of internal rotation are involved with the 120°K peaks of PiBMA and, in particular, PnBMA, which explain differences between PiBMA and PnBMA in the broadness and the temperature location of the 120°K peak. The 120°K peak is in general assigned to a side chain including a sequence? O? C? C? C or ? C? C? C? C. PiPMA without this sequence in the side chain does not show the 120°K peak, but it exhibits the 50°K peak (1 kHz) like poly(ethyl methacrylate). The 50°K peak is assigned to the rotation of ethyl or isopropyl group attached to COO group. Poly-L-valine in which the isopropyl group is directly attached to carbon does not have the 50°K peak. An additional loss peak at 20°K (1 kHz) for P4MP1 is also discussed on the basis of the calculated potential.     

Liquid crystal alignment behaviours on poly(methyl methacrylate) having polyhedral oligomeric silsesquioxane groups

A series of poly(methyl methacrylate) derivatives containing polyhedral oligomeric silsesquioxane (POSS) groups (MCP#) were synthesised via free radical polymerisation (FRP) using methacryl isobutyl POSS (MA-POSS) and methyl methacrylate as monomers to investigate liquid crystal (LC) alignment property of these polymer films. The LC cells made from the films of the polymers having 100 mol% of MA-POSS units (MCP100) showed vertical LC alignment having a pretilt angle of about 90°. The vertical LC alignment behaviour on the MCP100 film was ascribed to the very hydrophobic MCP100 surface having the surface energy value smaller than about 23 mJ/m² generated by the nonpolar bulky POSS group. Good electro-optical characteristics, such as voltage holding ratio (VHR) and residual DC voltage (R-DC), were observed for the LC cells fabricated using MCP100 as a LC alignment layer.     

Ultrasonic Modification of Polymers. II. Degradation of Polystyrene,Substituted Polystyrene,and Poly(n-vinyl Carbazole) in the Presence of Flexible Chain Polymers

Abstract

Ultrasonic (20 kHz, 70 W) solution degradations of polystyrene, substituted polystyrenes, and poly(n-vinyl carbazole) have been carried in toluene and tetrahydrofuran at 27 and -20°C in the presence of flexible chain polymers. Polystyrene formed block copolymers at 27°C with stiff-chain polymer PVCz; however, in the presence of flexible chain polymers, e.g., poly(vinyl methyl ketone) or poly(vinyl methyl ether), there were no block copolymers formed. Poly(n-vinyl carbazole) does not seem to form any block copolymers at 27°C with flexible chain polymers, e.g., poly(octadecyl methacrylate) and poly(ethyl methacrylate). Poly(p-chlorostyrene) and poly(p-methoxystyrene) also do not form block copolymers at 27°C with poly(octadecyl methacrylate) but do so with poly(hexadecyl methacrylate). It is quite possible that these may only be blends of two homopolymers. Poly(octa-decyl methacrylate) does yield a block copolymer when sonicated at -15°C with poly(p-isopropyl α-methylstyrene).     

Dielectric Relaxations in Plasma-Polymerized Hydrocarbons and Fluorocarbons

The dielectric behavior of plasma-polymerized ethylene (PPE), ethylene/acetylene (PPEA), ethane/vinyl chloride (PPEVC) and tetrafluoroethylene (PPTFE) was studied over a frequency range of 10² to 10⁵ Hz between -150 and 100°C. After exposure to the atmosphere, each of the polymers exhibited a pronounced loss peak. This relaxation process was designated as the γ_pprocess, and was attributed to the local mode motion of several molecular segments. The average activation energy for all four polymers was found to be 13.8 kcal/mole. It was proposed that oxidation introduces carbonyl groups into the nonpolar polymer chain. The added polar carbonyl groups then act as tracers to render the molecular motions observable by dielectric measurements. The presence of these carbonyl groups was confirmed by concomitant IR spectroscopic determinations. Comparison of the experimental data with the Kirkwood-Froelich theory was found to be satisfactory.     

Branching of anionic poly(methyl methacrylate)

A viscometric determination of the degree of branching γ, of poly(methyl methacrylate) obtained by anionic polymerization proved the reaction of the growing center of poly(methyl methacrylate) with the ester group of another polymer molecule, accompanied by the formation of a trifunctional branch point. This reaction occurs if the solution polymerization of methyl methacrylate is initiated: (1) with butyllithium at ?78°C only on attaining 100% conversion and after a long time or at +20°C immediately after the polymerization has set in; (2) with lithium tert-butoxide at +20°C after a long time. The degree of branching of poly(methyl methacrylates) obtained under similar conditions in the presence of tetrahydrofuran reaches higher values than for polymers prepared in toluene. The tacticity of polymers does not affect the experimentally determined γ values.     

Synthesis,characterization, and bulk properties of amphiphilic copolymers containing fluorinated methacrylates from sequential copper‐mediated radical polymerization

The partly fluorinated monomers, 2,2,2‐trifluoroethyl methacrylate (3FM), 2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate (8FM), and 1,1,2,2‐tetrahydroperfluorodecyl methacrylate (17FM) have been used in the preparation of block copolymers with methyl methacrylate (MMA), 2‐methoxyethyl acrylate (MEA), and poly(ethylene glycol) methyl ether methacrylate (PEGMA) by Atom Transfer Radical Polymerization. A kinetic study of the 3FM homopolymerization initiated with ethyl bromoisobutyrate and Cu(I)Br/N‐(n‐propyl)‐2‐pyridylmethanimine reveals a living/controlled polymerization in the range 80–110 °C, with apparent rate constants of 1.6 · 10⁻⁴ s⁻¹ to 2.9 · 10⁻⁴ s⁻¹. Various 3FM containing block copolymers with MMA are prepared by sequential monomer addition or from a PMMA macroinitiator in all cases with controlled characteristics. Block copolymers of 3FM and PEGMA resulted in block copolymers with PDI < 1.22, whereas block copolymers from 3FM and MEA have less controlled characteristics. The block copolymers based on MMA with 8FM and 17 FM have PDI's < 1.30. The glass transition temperatures of the block copolymers are dominated by the majority monomer, as the sequential monomer addition results in too short pure blocks to induce observable microphase separation. The thermal stability of the fluorinated poly((meth)acrylate)s in inert atmosphere is less than that of corresponding nonfluorinated poly((meth)acrylate)s. The presence of fluorinated blocks significantly increases the advancing water contact angle of thin films compared to films of the nonfluorinated poly((meth)acrylate)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8097–8111, 2008