Use of carbon black as a reinforcing nano-filler in conductivity-reversible elastomer composites

This study presents an innovative approach to the production of reinforced elastomer composites filled with carbon black Printex XE-2B, using the calendering process and ionic liquids (ILs) as dispersing agents. The effect of Printex XE-2B on the mechanical and electrical properties of acrylonitrile-butadiene rubber (NBR) composites was compared to that of conventional carbon black Humex N339. It was found that the highly structured Printex XE-2B significantly enhanced both the mechanical and electrical properties of the NBR composites, in contrast to standard Humex N339. To obtain uniform filler dispersion in the polymer matrix, several different ILs were employed as dispersing agents. The application of ILs had a considerable effect on the properties of the prepared composites, due to the improved dispersion of the filler particles in the composite matrix, which favored the formation of ‘conductive paths.’ Importantly, the prepared NBR/Printex XE-2B/IL composites were found to have reversible and repeatable electrical properties following exposure to chloroform vapors.     

Thermal characterization of the effect of fillers and ionic liquids on the vulcanization and properties of acrylonitrile–butadiene elastomer

Different thermal analysis techniques were used to study the effect of fillers and ionic liquids (ILs) on the vulcanization process, thermal and dynamic mechanical properties of acrylonitrile–butadiene elastomer (NBR). The products of the studies were composites of NBR filled with hydrotalcite, nanosized silica or carbon black. ILs such as 1-butyl-1-methylpyrrolidinium (BMpyrrolBF₄), 1-butyl-4-methylpyridinium (BMpyrBF₄) or 1-butyl-1-methylpiperidinium (BMpipBF₄) tetrafluoroborates were applied to improve the dispersion degree of the curatives and filler particles in the elastomer and to increase the efficiency of vulcanization. The differential scanning calorimetry results indicated that ILs reduced the vulcanization temperature of NBR compounds and increased the homogeneity of cross-link distribution in the elastomer network. NBRs filled with carbon black or silica exhibited similar thermal stabilities, whereas hydrotalcite reduced the temperature of thermal decomposition. The lowest mechanical loss factors were determined for vulcanizates filled with nanosized silica.

     

The physical and mechanical properties and cure characteristics of NBR/silica/MWCNT hybrid composites

The main objective of the present study was to investigate the synergistic effect of simultaneous use of two reinforcing fillers in rubber compounds based on acrylonitrile-butadiene copolymer (NBR). Silica was used as reinforcing filler in all samples and the loading content was 25 phr. 3 and 5 phr of multiwall carbon nanotubes (MWCNT) were used as second reinforcing filler in NBR/silica compounds. Melt mixing method was employed for compound preparation. The effects of carbon nanotube/silica hybrid filler on mechanical and vulcanization characteristics of the rubber compounds were investigated. These results revealed that addition of the reinforcing filler, either carbon nanotube or silica, shortened the optimum cure time (t₉₀) and also scorch time (t_s1) of samples compared to that of pure NBR compound. In hybrid compounds, the reduction in optimum cure time and scorch time was higher than that of for silica-filled NBR or CNT-filled NBR compounds. This can be attributed to the synergistic effect between CNT and silica as two reinforcing agents in NBR compounds. Regardless the composition of the reinforcing filler, an increase of the relaxed storage modulus is observed, while the tan δ value is decreased steadily. The dynamic modulus reinforcement of nanocomposites was examined by the Guth Gold and Modified Guth Gold equations. For hybrid samples, the experimental values show a significant positive deviation from model predictions. According to the Barlow’s formula, hybrid compounds show higher burst strength compared to silica or CNT filled NBR compounds.     

Dispersion and filler network structure of fibrillar silicates in elastomers

The dispersion and filler network of fibrillar silicate (FS) in elastomers were studied. The results showed that a good dispersion of FS in matrix during mechanical blending in unvulcanized composites contributed to a strong FS filler network, different from that of traditional reinforcing fillers. Meanwhile, the filler re-aggregation during vulcanization caused by the overlapping and intertwining of FS further strengthened the filler network. The factors including Mooney viscosity and molecular polarity of elastomer, type and amount of silane coupling agents used for filler modification, that may influence the filler network, were studied. Our study helps us to understand the mechanism for the formation of filler network of FS in elastomers and provides guidance for the preparation of high performance FS/elastomer composites.     

Recent developments in rubber processing,leading to new applications such as the “green tyre”

Rubber articles derive most of their mechanical properties from the admixture of reinforcing fillers. Most commonly, carbon black is used as reinforcing filler. If silica is used instead, tyres made with such rubber compounds may exhibit a rolling resistance reduction by ca. 30%, which translates in substantial fuel savings of a car. Such silicas are far more difficult to mix with rubber than carbon black. Coupling agents are used as a surface modification of the filler to enhance compatibility with the polymer. Additionally they improve the ease of mixing with the rubber. The development of proper coupling agents combined with improved mixing techniques has contributed to the final break-through of the silicareinforced “Green Tyre”.     

Influence of filler type and content on properties of styrene‐butadiene rubber (SBR) compound reinforced with carbon black or silica

Rubber compounds are filled with reinforcing fillers to improve their physical properties. Carbon black and silica have different surface chemistries to each other. Differences in properties of carbon black‐ and silica‐reinforced styrene‐butadiene rubber (SBR) compounds were studied. Variation of properties of carbon black‐ or silica‐filled compounds with the filler content was also investigated. The silica‐filled compounds without any coupling agent and dispering agent were prepared to investigate the influence of polar materials‐adsorption on the silica surface. Viscosity and crosslink density increased with increase of the filler content. Hardness, modulus, tensile strength, and wear property were improved more and more by increasing the filler content. Viscosity of the silica‐filled compound was higher than that of the carbon black‐filled one. Cure rate of the silica‐filled compound became slower as the filler content increased, while that of the carbon black‐filled one became faster. Difference in properties between the carbon black‐ and silica‐filled compounds were explained by the poor silica dispersion and the adsorption of cure accelerator on the silica surface. Copyright © 2004 John Wiley & Sons, Ltd.     

Cure characteristics and properties of NBR composites filled with co‐precipitates of black liquor and montmorillonite

Acrylonitrile‐butadiene rubber (NBR) composites filled with co‐precipitates of black liquor and montmorillonite (CLM) were prepared by mechanical mixing on a two‐roll mill. The cure characteristics, mechanical properties, thermal properties, and thermo‐oxidative aging properties of NBR/CLM composites were evaluated. Scanning electron microscopy and transmission electron microscopy showed that the filler particles were well dispersed in the NBR/CLM composites. The scorch time and optimum cure time increase with increasing filler loading. A remarkable enhancement in tensile strength, elongation at break, 300% modulus, and shore “A” hardness was also observed. When the loading of CLM was 40 parts per hundred rubbers, it showed about seven times increase in tensile strength, about 1.8 times increase in elongation at break, about three times increase in 300% modulus, and about 1.3 times increase in shore A hardness, respectively, as compared with those of pure cured NBR. Thermal properties and thermal oxidative aging properties, in general, were also improved with loading of this novel filler. Copyright © 2011 John Wiley & Sons, Ltd.     

Natural rubber biocomposites containing corn,barley and wheat straw

The development of high-performance materials made from available and cheap natural resources is increasing worldwide. A new solution – composites of natural rubber, containing barley, corn and wheat straw as biofillers, was reported and researched. The latest developments and trend's exams of the elastomers filled with cereal straw represent a scientific and technological innovation. The use of straw as a filler for elastomer composites bradens the range of functional properties and reduces the costs of production. The biocomposites are more ecofriendly and give the opportunity to increase the possibility of straw management which is a problematic agricultural waste. The rubber mixtures containing lignocellulosic materials demonstrate a favorable characteristic kinetics of crosslinking. The addition of filler, in an appropriate amount, modified natural rubber vulcanizates, improving mechanical and barrier properties of composites and the ability to damp under the influence of compression stress. Dynamic mechanical analysis showed change in the G′ values of the vulcanizates upon addition of straw. That indicates the presence of strongly developed network of fillers into polymer matrix which ensure of reinforcing character. The negative impact of natural fillers on resistance to thermo-oxidative aging was not observed.     

Evaluation of the properties of some nitrile–butadiene rubber/polychloroprene mixes and vulcanizates

Nitrile–butadiene rubber (NBR) has been blended with polychloroprene (CR) in a weight ratio of 1:1. The vulcanizing systems in the blend formulations were varied to obtain non crosslinked CR embedded in vulcanized NBR and non crosslinked NBR embedded in vulcanized CR. The effects of these two different phases on the rheological and mechanical characteristics were evaluated. In addition, the dynamic compliance of the blends was measured over wide ranges of frequency and temperature. It has been found that the mechanical and rheological properties of the vulcanized blends depend on the type of vulcanizing system, its concentration and the presence of reinforcing filler. The mechanical properties of the blend containing N‐cyclohexyl‐2‐benzthiazyl sulphenamide/S as vulcanizing system suitable for NBR are higher than those of the blend containing non‐sulfur vulcanizing system (Zno/Mgo and ethylene thiourea) suitable for CR. Both types of rubber (CR and NBR) in the blend are incompatible as two glass transition temperatures have been observed. Copyright © 2000 John Wiley & Sons, Ltd.     

Influence of Carbon Black and Silica Filler on the Rheological and Mechanical Properties of Natural Rubber Compound

Rubber compounds are reinforced with fillers such as carbon black and silica. In general, filled rubber compounds shows smooth rheological behavior and mechanical properties. Variation in rheological behavior and mechanical properties was studied in terms of the filler composition using natural rubber compounds filled with both carbon black and silica CB/Si = 0/60, 20/40, 30/30, 40/20 and 60/0 phr (parts per hundred rubber is parts of any non-rubbery material per hundred parts of raw gum elastomer (rubbery material)). The rheological behaviour can be showed in measurement of Mooney viscosity and cure time. The Mooney viscosity of rubber compounds increase with the increasing the carbon black in the compounds. The compound filled with CB/Si of 30/30 and 60/0 showed abnormal rheological behaviour in which the cure time decreased suddenly and the increased at certain ratio during the measurement. The mechanical properties such as hardness, abrasion resistance and tensile stress at 300% elongation were studied. In the hardness and abrasion resistance measurement, the higher ratio CB/Si decrease contribution of silica, which resulting smaller of hardness value. Ratio CB/Si 40/20 gives an optimum filler blended. It is also clearly understood that higher abrasion resistance mainly due to the lower hardness value under the same condition. The tensile stress at 300% elongation of rubber compound increased with the increasing carbon black filler.     

Blends of carbon blacks and multiwall carbon nanotubes as reinforcing fillers for hydrocarbon rubbers

The reinforcement of a styrene‐butadiene rubber (SBR) by single fillers—carbon black (CB) or multiwall carbon nanotubes (MWNTs)—or by mixtures of CB and MWNTs, is investigated. The morphologies, mechanical and electrical properties of the composites, are analyzed. A significant improvement in the tensile properties is observed for samples containing a dual phase. Using atomic force (AFM) and transmission electron (TEM) microscopies, we demonstrate that the double loading improves the dispersion of the nanotubes in SBR. Electrical measurements show lower resistivity and a lower percolation threshhold for composites containing blends of fillers, which provides further evidence of better dispersion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 46: 1939–1951, 2008     

Alteration of matrix curing characteristics and its role in extension of hydrodynamic equation for predicting viscoelastic properties of nitrile rubber/silica nanocomposites

Neglecting the alteration of matrix curing characteristics in a filled rubber nanocomposite, as a result of possible interactions between the nano filler and curing agent ingredients, leads to inaccurate properties prediction using conventional hydrodynamic equations. In the current work, we present a new empirical extended version of hydrodynamic equation and examine its capability in predicting the viscoelastic properties of NBR/nanosilica system in which the negative influence of the filler on the curing process of the NBR matrix was confirmed through various analyses such as tensile test, rheometry, swelling experiments, and dynamic mechanical analysis. The results showed that the proposed empirical extended model is able to account the contribution of alteration of matrix curing characteristics in changing the composite properties below the filler percolation threshold. It was demonstrated that the extended model provides more accurate prediction of viscoelastic properties of silica‐filled cured NBR nanocomposites above glass transition temperature.     

Radiation effect on properties of carbon black filled NBR/EPDM rubber blends

Rubber blend of acrylonitrile butadiene rubber (NBR) and ethylene-propylene diene monomer (EPDM) rubber (50/50) has been loaded with increasing contents, up to 100 phr, of reinforcing filler, namely, high abrasion furnace (HAF) carbon black. Prepared composites have been subjected to gamma radiation doses up to 250 kGy to induce radiation vulcanization under atmospheric conditions. Mechanical properties, namely, tensile strength (TS), tensile modulus at 100% elongation (M₁₀₀), and hardness have been followed up as a function of irradiation dose and degree of loading with filler. On the other hand, variation of the swelling number as a physical property, as a function of same parameters, however, in car oil as well as brake oil has been undertaken. In addition, the electrical properties of prepared composites, namely, their electrical conductivity, were also evaluated. The thermal behavior of the prepared composites was also investigated. The results obtained indicate that improvement has been attained in different properties of loaded NBR/EPDM composites with respect to unloaded ones.     

Formation of Network by Carbon Black，Silica and Their Mixing Fillers in Isoprene Rubber北大核心CSCD

The network formed by fillers has great influence on the mechanical properties of rubber materials. To understand the formation of network by carbon black,silica,and carbon black/silica mixing fillers in rubber and its influence on the properties of rubber,isoprene rubber/filler composites with different filler loadings are prepared and their micromorphology,rheological and tensile properties are investigated. It is found that the dispersion of fillers is better in rubber after cure than that in rubber before cure for all three rubber systems,and the filler size of silica is smaller than that of carbon black,but the aggregation is more severe in silica filled rubber system. In mixed filler system,the two fillers tend to aggregate separately, leading to the low modulus at small strain than that in single filler system. With the increase of the filler loading,the tensile strength increases first and then decreases,the elongation at break decreases,and the temperature rise in compression flexometer tests increases. Moreover,the temperature rise in mixed filler system is higher than that in single filler system at high filler loading. © 2022, Science Press (China). All rights reserved.     

Fabrication of exfoliated graphite reinforced silicone rubber composites - Mechanical,tribological and dielectric properties

The effect of exfoliated graphite (EG) on the mechanical, tribological and dielectric properties of the silicone rubber (QM) composites has been systematically investigated and analysed. Morphological analysis of the composites helps to understand the interfacial interaction between the filler and the rubber matrix as well as wear mechanism respectively. An enhancement in the mechanical, tribological and dielectric properties was observed with an increase in filler loading and better performance was observed at 7 phr of filler loading. The improvement in performance is attributed to the better interaction between the QM chains and the EG layers as evident from the AFM and TEM analysis. It is also evident from the Kraus plot which supports the reinforcing effect of EG in QM matrix.     

Properties of ethylene propylene diene rubber/white and black filler composites cured by gamma radiation in presence of sorbic acid

The effect of incorporating sorbic acid (SA), an echo-friendly curing agent, and silica or carbon black (CB) filler, as well as gamma irradiation on the physico-chemical, mechanical and thermal properties of ethylene propylene diene monomer rubber (EPDM) was investigated. The results indicated that the developed composites revealed improvement in the studied parameters over the untreated samples. Filler incorporation into rubber matrix has been proven a key factor in enhancing the swelling resistance, tensile strength and thermal properties of the fabricated composites. The improvement in tensile strength and modulus was attributed to better interfacial bonding via SA. Alternatively, a comparison was established between the performance of the white and black fillers. The utmost mechanical performance was reported for the incorporated ratios 10 phr SA and 40 phr white filler into a 50 kGy irradiated composite. Meanwhile, the incorporation of CB yielded better thermally stable composites than those filled with silica at similar conditions.     

Novel in situ coordination copper sulfate/ acrylonitrile–butadiene rubber composite

A novel rubber composite of acrylonitrile–butadiene rubber (NBR) filled with anhydrous copper sulfate (CuSO₄) particles was investigated. Dynamic mechanical analysis, differential scanning calorimetry, X‐ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of this novel CuSO₄/NBR composite. The results indicated that the composite had wonderful mechanical properties, which profited from the in situ coordination crosslinking interactions between the nitrile groups (? CN) of NBR and solid CuSO₄ particles. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, and transmission electron microscopy results showed that CuSO₄ particles played two roles, acting as both crosslink agents and reinforcing fillers in the matrix. The double actions of CuSO₄ gave the CuSO₄/NBR composites their excellent mechanical properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 571–576, 2007     

Interfaces in Composites. Reinforcement of Elastomers by Carbon Black

Basic features of carbon black-aggregation of particles into structure, particle size and morphology, and surface activity-are reviewed. Carbon black reinforcement of vulcanizates is first examined in the example of tearing, and the influence of hysteresis is considered. The dynamic properties of vulcanizates containing two major types of reinforcing carbon black are compared.

While particle size gives the best correlation with tensile strength of vulcanizates, surface activity is shown to be the key to reinforcement. The role of these properties of carbon black in dissipating rupture energy is discussed.

The relation between work to tensile break and hysteresis to break in gum rubbers can be applied to black-reinforced vulcanizates by use of a strain amplification factor. The complication introduced by stress-softening is explained in terms of localized stress relaxation. Abrasion reinforcement can also be explained in terms of hysteresis.

The Flory-Rehner relationship of modulus of elasticity of swollen vulcanizates to physically-effective cross-linking applies to unswollen vulcanizates only after prestressing. Black-reinforced vulcanizates involve application of the strain amplification factor.

The concept of mobile linkages to rubber chains at the surface of black particles is related to the influence of strain magnification and strain rate magnification in the reinforcing mechanism. These linkages result in formation of “shell” rubber adjacent to carbon black particles. The slippage of rubber chains relative to carbon black aggregates allows stress-sharing by highly-stressed chains. Bound rubber results from reaction of elastomer free radicals generated during mastication with carbon black.

There is a relation between bound rubber and reinforcement which is fully developed only after vulcanization. Formation of bound rubber results from the surface activity of carbon black rather than its structure. Its contribution to reinforcement of the vulcanizate may be as important as cross-linking.     

Reinforcement of compatibilized NR/NBR blends by fly ash particles and precipitated silica

Effects of precipitated silica (PSi) and silica from fly ash (FA) particles (FASi) on the cure and mechanical properties before and after thermal and oil aging of natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) blends with and without chloroprene rubber (CR) or epoxidized NR (ENR) as a compatibilizer have been reported in this paper. The experimental results suggested that the scorch and cure times decreased with the addition of silica and the compound viscosity increased on increasing the silica content. The mechanical properties for PSi filled NR/NBR vulcanizates were greater than those for FASi filled NR/NBR vulcanizates in all cases. The PSi could be used for reinforcing the NR/NBR vulcanizates while the silica from FA was regarded as a semi‐reinforcing and/or extending filler. The incorporation of CR or ENR enhanced the mechanical properties of the NR/NBR vulcanizates, the ENR being more effective and compatible with the blend. The mechanical properties of the NR/NBR vulcanizates were improved by post‐curing effect from thermal aging but deteriorated by the oil aging. Copyright © 2008 John Wiley & Sons, Ltd.     

Improvement of properties of silica‐filled styrene‐butadiene rubber composites through plasma surface modification of silica

The performance of plasma surface modified silica filler in styrene‐butadiene rubber (SBR) matrix has been analyzed. The conditions of plasma modification have been optimized by taking secant modulus as a standard parameter and the occurrence of the modification has been confirmed by surface area determination and Fourier transform infrared spectroscopy. The plasma‐modified surface of silica has been found to be composed of carbon–carbon double bonds and carbon–hydrogen bonds. Silane treatment also has been carried out on silica filler surface for a comparative assessment of its influence in the curing behavior and filler–rubber interaction. The cure reactions of all the rubber compounds have been found to be proceeded according to first‐order kinetics. A reduction in the cure reaction rate constant has been observed with the loading of unmodified and surface modified silica, emphasizing the cure deactivation of the matrix rubber by the silica filler. The filler dispersion, as revealed by scanning electron microscopy, has been found to be greatly improved by the plasma as well as silane treatment. The filler–rubber interaction has been found to be greatly improved by both surface treatments, but the best balance of mechanical properties has been observed with plasma surface modification only. Copyright © 2004 John Wiley & Sons, Ltd.