Kinetic analysis of surface‐initiated SET‐LRP of poly(N‐isopropylacrylamide)

The single‐electron transfer living radical polymerization (SET‐LRP) of N‐isopropylacrylamide (NIPAM) from silicon wafer modified with an initiator layer composed of 2‐bromopropionyl bromide (2‐BPB) fragments is described. The amount of Cu(0) generated in situ by the disproportination of Cu(I) to Cu(0) and Cu(II) in the presence of 2,2′‐bipyridine (2,2′‐bpy) ligand and N,N‐dimethylformamide (DMF) solvent at 90 °C is dependent on the ratio of [CuBr]/[CuBr₂]. By proper selection of the [CuBr]/[CuBr₂] ratio, well‐controlled SET‐LRP polymerization of NIPAM was observed such that the thickness of the layer consisting of chains grown from the surface increased linearly with the molecular weight of chains polymerized in solution in identical. In addition, the calculation of grafting parameters, including surface coverage, σ (mg/m²); grafting density, Σ (chain/nm²); and average distance between grafting sites, D (nm), from the number‐average molecular weight, M _n (g/mol), and ellipsometric thickness, h (nm), values indicated the synthesis of densely grafted poly(NIPAM) films and allowed us to predict a “brush‐like” conformation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Doubly thermoresponsive brush‐linear‐linear ABC triblock copolymer nanoparticles prepared through dispersion RAFT polymerization

Doubly thermoresponsive ABC brush‐linear‐linear triblock copolymer nanoparticles of poly[poly(ethylene glycol) methyl ether vinylphenyl]‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene [P(mPEGV)‐b‐PNIPAM‐b‐PS] containing two thermoresponsive blocks of poly[poly(ethylene glycol) methyl ether vinylphenyl] [P(mPEGV)] and poly(N‐isopropylacrylamide) (PNIPAM) are prepared by macro‐RAFT agent mediated dispersion polymerization. The P(mPEGV)‐b‐PNIPAM‐b‐PS nanoparticles exhibit two separate lower critical solution temperatures or phase‐transition temperatures (PTTs) corresponding to the linear PNIPAM block and the brush P(mPEGV) block in water. Upon temperature increasing above the first and then the second PTT, the hydrodynamic diameter (D_h) of the triblock copolymer nanoparticles undergoes an initial shrinkage at the first PTT and the subsequent shrinkage at the second PTT. The effect of the chain length of the PNIPAM block on the thermoresponsive behavior of the triblock copolymer nanoparticles is investigated. It is found that, the longer chains of the thermoresponsive PNIPAM block, the greater contribution on the transmittance change of the aqueous dispersion of the triblock copolymer nanoparticles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2266–2278     

Aqueous RAFT polymerization of N‐isopropylacrylamide‐mediated with hydrophilic macro‐RAFT agent: Homogeneous or heterogeneous polymerization?

Aqueous RAFT polymerization of N‐isopropylacrylamide (NIPAM) mediated with hydrophilic macro‐RAFT agent is generally used to prepare poly(N‐isopropylacrylamide) (PNIPAM)‐based block copolymer. Because of the phase transition temperature of the block copolymer in water being dependent on the chain length of the PNIPAM block, the aqueous RAFT polymerization is much more complex than expected. Herein, the aqueous RAFT polymerization of NIPAM in the presence of the hydrophilic macro‐RAFT agent of poly(dimethylacrylamide) trithiocarbonate is studied and compared with the homogeneous solution RAFT polymerization. This aqueous RAFT polymerization leads to the well‐defined poly(dimethylacrylamide)‐b‐poly(N‐isopropylacrylamide)‐b‐poly(dimethylacrylamide) (PDMA‐b‐PNIPAM‐b‐PDMA) triblock copolymer. It is found, when the triblock copolymer contains a short PNIPAM block, the aqueous RAFT polymerization undergoes just like the homogeneous one; whereas when the triblock copolymer contains a long PNIPAM block, both the initial homogeneous polymerization and the subsequent dispersion polymerization are involved and the two‐stage ln([M]_o/[M])‐time plots are indicated. The reason that the PNIPAM chain length greatly affects the aqueous RAFT polymerization is discussed. The present study is anticipated to be helpful to understand the chain extension of thermoresponsive block copolymer during aqueous RAFT polymerization. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of well‐defined 7‐arm and 21‐arm poly(N‐isopropylacrylamide) star polymers with β‐cyclodextrin cores via click chemistry and their thermal phase transition behavior in aqueous solution

The syntheses of well‐defined 7‐arm and 21‐arm poly(N‐isopropylacrylamide) (PNIPAM) star polymers possessing β‐cyclodextrin (β‐CD) cores were achieved via the combination of atom transfer radical polymerization (ATRP) and click reactions. Heptakis(6‐deoxy‐6‐azido)‐β‐cyclodextrin and heptakis[2,3,6‐tri‐O‐(2‐azidopropionyl)]‐β‐cyclodextrin, β‐CD‐(N₃)₇ and β‐CD‐(N₃)₂₁, precursors were prepared and thoroughly characterized by nuclear magnetic resonance and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. A series of alkynyl terminally functionalized PNIPAM (alkyne‐PNIPAM) linear precursors with varying degrees of polymerization (DP) were synthesized via atom transfer radical polymerization (ATRP) of N‐isopropylacrylamide using propargyl 2‐chloropropionate as the initiator. The subsequent click reactions of alkyne‐PNIPAM with β‐CD‐(N₃)₇ and β‐CD‐(N₃)₂₁ led to the facile preparation of well‐defined 7‐arm and 21‐arm star polymers, namely β‐CD‐(PNIPAM)₇ and β‐CD‐(PNIPAM)₂₁. The thermal phase transition behavior of 7‐arm and 21‐arm star polymers with varying molecular weights were examined by temperature‐dependent turbidity and micro‐differential scanning calorimetry, and the results were compared to those of linear PNIPAM precursors. The anchoring of PNIPAM chain terminal to β‐CD cores and high local chain density for star polymers contributed to their considerably lower critical phase separation temperatures (T_c) and enthalpy changes during phase transition as compared with that of linear precursors. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 404–419, 2009     

An H‐shaped polymer bonding β‐cyclodextrin at branch points: Synthesis and influences of attached β‐cyclodextrins on physical properties

We report on the synthesis of an H‐shaped polymer bonding β‐cyclodextrin (β‐CD) at branch points and influences of attached β‐CD on physical properties. First, a poly(ethylene glycol)(PEG)‐based functional macroinitiator bearing two azidos and four chlorines at chain‐ends (PEG‐2N₃(‐4Cl)) was prepared via terminal modification reactions. Then, PEG‐2N₃(‐4Cl) was applied to initiate the atom transfer radical polymerization of N‐isopropylacrylamide, leading to the synthesis of an H‐shaped block polymer with PEG as the central chain and poly(N‐isopropylacrylamide) (PNIPAM) as side‐arms (PEG‐2N₃(‐4PNIPAM)). Azido groups were at the branch points of the polymer. Finally, the click reaction between PEG‐2N₃(‐4PNIPAM) and alkynyl monosubstituted β‐cyclodextrin (β‐CD) afforded another H‐shaped polymer with two β‐CDs bonding at the polymer branch points (PEG‐2CD(‐4PNIPAM)). The glass transition temperature (T_g) and lower critical solution temperature (LCST) of the H‐shaped polymer increased after the attachment of β‐CD. The self‐assembly and thermal responsive behaviors, as well as the encapsulation behaviors of PEG‐2CD(‐4PNIPAM) were also altered. When temperature was below the LCSTs, PEG‐2N₃(‐2PNIPAM) dissolved in water molecularly, whereas PEG‐2CD(‐4PNIPAM) could self‐assemble into nano‐sized micelles. After the LCST transitions, PEG‐2N₃(‐4PNIPAM) aggregated into micron‐sized unstable particles, whereas PEG‐2CD(‐4PNIPAM) transformed into PNIPAM‐cored nanomicelles. Besides, PEG‐2CD(‐4PNIPAM) can encapsulate doxorubicin below its LCST due to the formation of micelles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

SET‐LRP synthesis of PMHDO‐g‐PNIPAM well‐defined amphiphilic graft copolymer

A well‐defined amphiphilic graft copolymer, consisting of hydrophobic polyallene‐based backbone and hydrophilic poly(N‐isopropylacrylamide) (PNIPAM) side chains, was prepared by the combination of living coordination polymerization, single electron transfer‐living radical polymerization (SET‐LRP), and the grafting‐from strategy. First, the double‐bond‐containing backbone was prepared by [(η³‐allyl)NiOCOCF₃]₂‐initiated living coordination polymerization of 6‐methyl‐1,2‐heptadiene‐4‐ol (MHDO). Next, the pendant hydroxyls in every repeating unit of poly(6‐methyl‐1,2‐heptadiene‐4‐ol) (PMHDO) homopolymer were treated with 2‐chloropropionyl chloride to give PMHDO‐Cl macroinitiator. Finally, PNIPAM side chains were grown from PMHDO backbone via SET‐LRP of N‐isopropylacrylamide initiated by PMHDO‐Cl macroinitiator in N,N‐dimethylformamide/2‐propanol using copper(I) chloride/tris(2‐(dimethylamino)ethyl)amine as catalytic system to afford PMHDO‐g‐PNIPAM graft copolymers with a narrow molecular weight distribution (M_w/M_n = 1.19). The critical micelle concentration (cmc) in water was determined by fluorescence probe technique and the effects of pH and salinity on the cmc of PMHDO‐g‐PNIPAM were also investigated. The micellar morphology was found to be spheres using transmission electron microscopy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and self‐assembly of tadpole‐shaped organic/inorganic hybrid poly(N‐isopropylacrylamide) containing polyhedral oligomeric silsesquioxane via RAFT polymerization

Aminopropylisobutyl polyhedral oligomeric silsesquioxane (POSS) was used to prepare a POSS‐containing reversible addition‐fragmentation transfer (RAFT) agent. The POSS‐containing RAFT agent was used in the RAFT polymerization of N‐isopropylacrylamide (NIPAM) to produce tadpole‐shaped organic/inorganic hybrid Poly(N‐isopropylacrylamide) (PNIPAM). The results show that the POSS‐containing RAFT agent was an effective chain transfer agent in the RAFT polymerization of NIPAM, and the polymerization kinetics were found to be pseudo‐first‐order behavior. The thermal properties of the organic/inorganic hybrid PNIPAM were also characterized by differential scanning calorimetry. The glass transition temperature (T_g) of the tadpole‐shaped inorganic/organic hybrid PNIPAM was enhanced by POSS molecule. The self‐assembly behavior of the tadpole‐shaped inorganic/organic hybrid PNIPAM was investigated by atomic force microscopy and dynamic light scattering. The results show the core‐shell nanostructured micelles with a uniform diameter. The diameter of the micelle increases with the molecular weight of the hybrid PNIPAM. Surprisingly, the micelle of the tadpole‐shaped inorganic/organic hybrid PNIPAM with low molecular weight has a much bigger and more compact core than that with high molecular weight. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7049–7061, 2008     

Preparation and characterization of temperature‐ and pH‐responsive diblock copolymers and their silica‐coated nanoparticles

Multiresponsive amphiphilic poly(N,N‐dimethylaminoethyl methacrylate)‐b‐poly(N‐isopropylacrylamide) (PDMAEMA‐b‐PNIPAM) was successfully synthesized by reversible addition‐fragmentation chain transfer polymerization. Poly(N,N‐dimethylaminoethyl methacrylate)‐b‐poly(N‐isopropylacrylamide) has thermal and pH stimuli responsiveness. Their lower critical solution temperature and hydrodynamic radius can be adjusted by varying the copolymer composition, block length, solution pH, and temperature. In addition, a convenient method has been established to prepare cross‐linked silica‐coated nanoparticles with PDMAEMA‐b‐PNIPAM micelles as a template, resulting in good organic/inorganic hybrid nanoparticles defined as 175 to 220 nm. The structure and morphology were characterized by proton nuclear magnetic resonance (₁HNMR), Fourier‐transform infrared spectroscopy (FT‐IR), transmission electron microscopy (TEM), and transmission electron microscopy‐energy dispersive X‐ray spectroscopy (TEM‐EDS).     

A New Approach for the Synthesis of Miktoarm Star Polymers Through a Combination of Thiol–Epoxy “Click” Chemistry and ATRP/Ring‐Opening Polymerization Techniques

A new approach was developed for synthesis of certain A₃B₃‐type of double hydrophilic or amphiphilic miktoarm star polymers using a combination of “grafting onto” and “grafting from” methods. To achieve the synthesis of desired miktoarm star polymers, acetyl protected poly(ethylene glycol) (PEG) thiols (M_n = 550 and 2000 g mol^?1) were utilized to generate A₃‐type of homoarm star polymers through an in situ protective group removal and a subsequent thiol–epoxy “click” reaction with a tris‐epoxide core viz. 1,1,1‐tris(4‐hydroxyphenyl)ethane triglycidyl ether. The secondary hydroxyl groups generated adjacent to the core upon the thiol–epoxy reaction were esterified with α‐bromoisobutyryl bromide to install atom transfer radical polymerization (ATRP) initiating sites. ATRP of N‐isopropylacrylamide (NIPAM) using the three‐arm star PEG polymer fitted with ATRP initiating sites adjacent to the core afforded A₃B₃‐type of double hydrophilic (PEG)₃[poly(N‐isopropylacrylamide)] (PNIPAM)₃ miktoarm star polymers. Furthermore, the generated hydroxyl groups were directly used as initiator for ring‐opening polymerization of ε‐caprolactone to prepare A₃B₃‐type of amphiphilic (PEG)₃[poly(ε‐caprolactone)]₃ miktoarm star polymers. The double hydrophilic (PEG)₃(PNIPAM)₃ miktoarm star polymers showed lower critical solution temperature around 34 °C. The preliminary transmission electron microscopy analysis indicated formation of self‐assembly of (PEG)₃(PNIPAM)₃ miktoarm star polymer in aqueous solution. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 146–156     

Dual thermo‐ and pH‐sensitive network‐grafted hydrogels formed by macrocrosslinker as drug delivery system

Dual thermo‐ and pH‐sensitive network‐grafted hydrogels made of poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) network and poly(N‐isopropylacrylamide) (PNIPAM) grafting chains were successfully synthesized by the combination of atom transfer radical polymerization (ATRP), reversible addition‐fragmentation chain transfer (RAFT) polymerization, and click chemistry. PNIPAM having two azide groups at one chain end [PNIPAM‐(N₃)₂] was prepared with an azide‐capped ATRP initiator of N,N‐di(β‐azidoethyl) 2‐chloropropionylamide. Alkyne‐pending poly(N,N‐dimethylaminoethyl methacrylate‐co‐propargyl acrylate) [P(DMAEMA‐co‐ProA)] was obtained through RAFT copolymerization using dibenzyltrithiocarbonate as chain transfer agent. The subsequent click reaction led to the formation of the network‐grafted hydrogels. The influences of the chemical composition of P(DMAEMA‐co‐ProA) on the properties of the hydrogels were investigated in terms of morphology and swelling/deswelling kinetics. The dual stimulus‐sensitive hydrogels exhibited fast response, high swelling ratio, and reproducible swelling/deswelling cycles under different temperatures and pH values. The uptake and release of ceftriaxone sodium by these hydrogels showed both thermal and pH dependence, suggesting the feasibility of these hydrogels as thermo‐ and pH‐dependent drug release devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Scaling of the molecular weight‐dependent thermal volume transition of poly(N‐isopropylacrylamide)

A series of narrowly distributed poly(N‐isopropylacrylamide) (PNIPAM) with molecular weight ranging from 8 × 10⁴ to 2.3 × 10⁷ g/mol were prepared by a combination of free radical polymerization and fractional precipitation. An ultrasensitive differential scanning calorimetry was used to study the effect of molecular weight on the thermal volume transition of these PNIPAM samples. The specific heat peak of the transition temperature (T_p,0) was obtained by extrapolation to zero heating rate (HR) because of the linear dependence of the transition temperature (T_p) on the HR. The relation between T_p,0 and the degree of polymerization (N) was investigated. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1388–1393, 2010     

Synthesis and Characterization of Aminoporphyrin‐End‐Functionalized Poly(N‐isopropylacrylamide) with Photodynamic and Thermoresponsive Effects

The novel aminoporphyrin‐end‐functionalized poly(N‐isopropylacrylamide) (PNIPAM) polymer H₂N‐TPP‐PNIPAM (TPP=5,10,15,20‐tetraphenyl‐21H,23H‐porphyrin) behaves as a multifunctional platform that displays a photodynamic effect, thermosensitivity, and fluorescence properties. The polymer was designed by using an asymmetrical aminoporphyrin (i.e., H₂N‐TPP‐Cl) as the initiator for the atom‐transfer radical polymerization of N‐isopropylacrylamide (NIPAM). The polydispersity index (PDI) obtained by gel‐permeation chromatography indicated that the molecular‐weight distribution was narrow (1.09<PDI<1.27). The lower critical solution temperatures of H₂N‐TPP‐PNIPAM showed a decreasing trend as the molecular weight was increased as a result of the incorporation of the porphyrin group at the end of the chain. The fluorescence spectra revealed the luminescent properties of the materials. The results of confocal laser scanning microscopy showed that the polymer could enter the cytoplasm through endocytosis. In addition, the multifunctional platform exhibited low toxicity against normal cells (L929) and cancer cells (Hela) and enhanced photodynamic activity towards HeLa cells, without significant necrocytosis towards L929 cells; as a result this material may be useful in the future for practical photodynamic therapy.     

Synthesis and swelling behavior of comb‐type grafted hydrogels by reversible addition–fragmentation chain transfer polymerization

The comb‐type grafted hydrogels poly(N‐isopropylacrylamide)‐g‐poly(N‐isopropylacrylamide) (PNIPAM‐g‐PNIPAM) and poly(acrylic acid)‐g‐poly(N‐isopropylacrylamide) (PAAc‐g‐PNIPAM) were prepared by reversible addition–fragmentation chain transfer polymerization. A macromolecular chain‐transfer agent was prepared first. Then, hydrogels were obtained by a reaction with a comonomer (N‐isopropylacrylamide or acrylic acid) in the presence of N,N‐methylenebisacrylamide as a crosslinker. The equilibrium swelling ratios and the swelling and deswelling kinetics of PNIPAM‐g‐PNIPAM were measured. The effects of the chain length and amount on the swelling behavior were investigated. The deswelling mechanism was illustrated. Meanwhile, the PAAc‐g‐PNIPAM hydrogel was used to confirm the versatility of this novel method. It was prepared in an alcoholic medium, whereas hydrogen‐bonding complexes formed in 1,4‐dioxane, which was chosen as the reaction medium for the PNIPAM‐g‐PNIPAM hydrogel. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2615–2624, 2005     

Thermo‐responsive fluorescent micelles from amphiphilic A3B miktoarm star copolymers prepared via a combination of SET‐LRP and RAFT polymerization

A novel amphiphilic A₃B miktoarm star copolymer poly(N‐isopropylacrylamide)₃‐poly(N‐vinylcarbazole) ((PNIPAAM)₃(PVK)) was successfully synthesized by a combination of single‐electron transfer living radical polymerization (SET‐LRP) and reversible addition‐fragmentation chain transfer (RAFT) polymerization. First, the well‐defined three‐armed poly(N‐isopropylacrylamide) (PNIPAAM)₃ was prepared via SET‐LRP of N‐isopropylacrylamide in acetone at 25 °C using a tetrafunctional bromoxanthate iniferter (Xanthate‐Br₃) as the initiator and Cu(0)/PMDETA as a catalyst system. Secondly, the target amphiphilic A₃B miktoarm star copolymer ((PNIPAAM)₃(PVK)) was prepared via RAFT polymerization of N‐vinylcarbazole (NVC) employing (PNIPAAM)₃ as the macro‐RAFT agent. The architecture of the amphiphilic A₃B miktoarm star copolymers were characterized by GPC, ¹H‐NMR spectra. Furthermore, the fluorescence intensity of micelle increased with the temperature and had a good temperature reversibility, which was investigated by dynamic light scattering (DLS), fluorescent and UV‐vis spectra. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4268–4278, 2010     

One‐pot synthesis of composite microspheres with core‐shell structure

One‐pot synthesis of thermoresponsive magnetic composite microspheres with a poly(N‐isopropylacrylamide) (PNIPAM) shell and a Fe₃O₄ core is demonstrated. Temperature sensitivity of PNIPAM was adopted to design the novel synthesis pathway. The as‐prepared composite microspheres have an obvious core‐shell structure with a mean size of approximately 250 nm. The Fe₃O₄ core is approximately 5 nm and the thickness of the PNIPAM shell is approximately 10 nm. The content of Fe₃O₄ in the composite microspheres can be controlled by this method. The composite microspheres experience a swelling and shrinking process in water by adjusting the temperature below and above the lower critical solution temperature (LCST) around 32 °C. These microspheres also show fine response to an external magnetic field. This work presents a platform to synthesize organic/inorganic composite microspheres in a facile and efficient approach. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2702–2708     

Polymerization of styrene in alcohol/water mediated by a macro‐RAFT agent of poly(N‐isopropylacrylamide) trithiocarbonate: From homogeneous to heterogeneous RAFT polymerization

The reversible addition fragmentation chain transfer (RAFT) polymerization of styrene in alcohol/water mixture mediated with the poly(N‐isopropylacrylamide) trithiocarbonate macro‐RAFT agent (PNIPAM‐TTC) is studied and compared with the general RAFT dispersion polymerization in the presence of a small molecular RAFT agent. Both the homogeneous/quasi‐homogeneous polymerization before particle nucleation and the heterogeneous polymerization after particle nucleation are involved in the PNIPAM‐TTC‐mediated RAFT polymerization, and the two‐stage increase in the molecular weight (M_n) and nanoparticle size of the synthesized block copolymer is found. In the initial homogeneous/quasi‐homogeneous polymerization, the M_n and nanoparticle size slowly increase with monomer conversion, whereas the M_n and particle size quickly increase in the subsequent heterogeneous RAFT polymerization, which is much different from those in the general RAFT dispersion polymerization. Besides, the PNIPAM‐TTC‐mediated RAFT polymerization runs much faster than the general RAFT dispersion polymerization. This study is anticipated to be helpful to understand the polymer chain extension through RAFT polymerization under dispersion conditions. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermal and pH‐sensitive gold nanoparticles from H‐shaped block copolymers of (PNIPAM/PDMAEMA)‐b‐PEG‐b‐(PNIPAM/PDMAEMA)

Well‐defined H‐shaped pentablock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM), poly(N,N‐dimethylaminoethylacrylamide) (PDMAEMA), and poly(ethylene glycol) (PEG) with the chain architecture of (A/B)‐b‐C‐b‐(A/B) were synthesized by the combination of single‐electron‐transfer living radical polymerization, atom‐transfer radical polymerization, and click chemistry. Single‐electron‐transfer living radical polymerization of NIPAM using α,ω azide‐capped PEG macroinitiator resulted in PNIPAM‐b‐PEG‐b‐PNIPAM with azide groups at the block joints. Atom‐transfer radical polymerization of DMAEMA initiated by propargyl 2‐chloropropionate gave out α‐capped alkyne‐PDMAEMA. The H‐shaped copolymers were finally obtained by the click reaction between PNIPAM‐b‐PEG‐b‐PNIPAM and alkyne‐PDMAEMA. These copolymers were used to prepare stable colloidal gold nanoparticles (GNPs) in aqueous solution without any external reducing agent. The formation of GNPs was affected by the length of PDMAEMA block, the feed ratio of the copolymer to HAuCl₄, and the pH value. The surface plasmon absorbance of these obtained GNPs also exhibited pH and thermal dependence because of the existence of PNIAPM and PDAMEMA blocks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Salt‐Induced Depression of Lower Critical Solution Temperature in a Surface‐Grafted Neutral Thermoresponsive Polymer

Summary: Quartz crystal microbalance with dissipation monitoring (QCM‐D) is employed to determine the effect of salt on the volume phase transition of thermoresponsive polymer brushes. Changes in mass and viscoelasticity of poly(N‐isopropylacrylamide) (PNIPAM) layers grafted from a QCM‐D crystal are measured as a function of temperature, upon contact with aqueous solutions of varying salt concentrations. The phase‐transition temperature of PNIPAM brushes, T_C,graft, quantified from the QCM‐D measurements is found to decrease as the concentration of salt is increased. This phenomenon is explained by the tendency of salt ions to affect the structure of water molecules (Hofmeister effect). However, in contrast to the linear decrease in phase‐transition temperature upon increasing salt concentration observed for free PNIPAM, the trend in T_C,graft for PNIPAM brushes is distinctively non‐linear.

Schematic representation of the effect of salt concentration on the phase transition behavior of thermoresponsive polymer brushes.     

R‐RAFT approach for the polymerization of N‐isopropylacrylamide with a star poly(ε‐caprolactone) core

Reversible addition‐fragmentation chain transfer (RAFT) polymerization is a more robust and versatile approach than other living free radical polymerization methods, providing a reactive thiocarbonylthio end group. A series of well‐defined star diblock [poly(ε‐caprolactone)‐b‐poly(N‐isopropylacrylamide)]₄ (SPCLNIP) copolymers were synthesized by R‐RAFT polymerization of N‐isopropylacrylamide (NIPAAm) using [PCL‐DDAT]₄ (SPCL‐DDAT) as a star macro‐RAFT agent (DDAT: S‐1‐dodecyl‐S′‐(α, α′‐dimethyl‐α″‐acetic acid) trithiocarbonate). The R‐RAFT polymerization showed a controlled/“living” character, proceeding with pseudo‐first‐order kinetics. All these star polymers with different molecular weights exhibited narrow molecular weight distributions of less than 1.2. The effect of polymerization temperature and molecular weight of the star macro‐RAFT agent on the polymerization kinetics of NIPAAm monomers was also addressed. Hardly any radical–radical coupling by‐products were detected, while linear side products were kept to a minimum by careful control over polymerization conditions. The trithiocarbonate groups were transferred to polymer chain ends by R‐RAFT polymerization, providing potential possibility of further modification by thiocarbonylthio chemistry. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Control of thermoresponsive property of urea end‐functionalized poly(N‐isopropylacrylamide) based on the hydrogen bond‐assisted self‐assembly in water

The precise synthesis and variation in the thermoresponsive property based on the supramolecular assembly of a novel urea end‐functionalized poly(N‐isopropylacrylamide) (PNIPAM) were studied. A series of PNIPAMs with different diphenylurea groups at the chain end (X? Ph? NH? CO? NH? Ph? trz? PNIPAM: X = H, OCH₃, CH₃, NO₂, Cl, and CF₃) were synthesized by using a combination of the atom transfer radical polymerization and the copper(I)‐catalyzed azide‐alkyne cycloaddition. The cloud point of the obtained polymers depended on the hydrogen‐bonding ability of the introduced urea group. The ¹H NMR measurement suggested that the obtained PNIPAM assembled in water via the intermolecular hydrogen bonding by the terminal urea group. From the dynamic light scattering and transmission electron microscopy measurements, the aggregated nanoparticles of the resulting polymer were directly observed in water at a temperature below its cloud point. The hydrogen‐bonding property of the chain end urea group was concluded to be involved in the aggregation of the PNIPAM in water, leading to the variation in its cloud point. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6259–6268, 2009