Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Cross‐linked poly(aryl ether sulfone) membranes for direct methanol fuel cell applications

Partially sulfonated poly(aryl ether sulfone) (PESS) was synthesized and methacrylated via reaction with glycidyl methacrylate (PESSGMA) and cross‐linked via radical polymerization with styrene and vinyl‐phosphonic acid (VPA). The chemical structures of the synthesized pre‐polymers were characterized via FTIR and ¹H NMR spectroscopic methods and molecular weight was determined via GPC. Membranes of these polymers were prepared via solution casting method. The crosslinking of the PESS polymer reduced IEC, proton conductivity, swelling in water, and methanol permeability of the membranes while increasing the modulus and the glass transition temperature. However, the introduction of the VPA comonomer increased the proton conductivity while maintaining excellent resistance to methanol cross‐over, which was significantly higher as compared with both PESS and the commercial Nafion membranes. Membranes of PESSGMA copolymers incorporating VPA, exhibited proton conductivity values at 60 °C in the range of 16–32 mS cm⁻¹ and methanol permeability values in the range of 6.52 × 10⁻⁹ – 1.92 × 10⁻⁸ cm² s⁻¹. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 558–575     

Sorption and diffusion of methanol and water in PVDF‐g‐PSSA and Nafion® 117 polymer electrolyte membranes

Sorption and diffusion properties of poly(vinylidene fluoride)‐graft‐poly(styrene sulfonic acid) (PVDF‐g‐PSSA) and Nafion® 117 polymer electrolyte membranes were studied in water/methanol mixtures. The two types of membranes were found to have different sorption properties. The Nafion 117 membrane was found to have a maximum in‐solvent uptake around 0.4 to 0.6 mole fraction of methanol, while the PVDF‐g‐PSSA membranes took up less solvent with increasing methanol concentration. The proton NMR spectra were recorded for membranes immersed in deuterated water/methanol mixtures. The spectra showed that the hydroxyl protons inside the membrane exhibit resonance lines different from the resonance lines of hydroxyl protons in the external solvent. The spectral features of the lines of these internal hydroxyl groups in the membranes were different in the Nafion membrane compared with the PVDF‐g‐PSSA membranes. Diffusion measurements with the pulsed field gradient NMR (PFG‐NMR) method showed that the diffusion coefficient of the internal hydroxyl groups in the solvent immersed Nafion membrane mirrors the changes in the diffusion coefficients of hydroxyl and methyl protons in the external solvent. For the PVDF‐g‐PSSA membranes, a decrease in the diffusion coefficient of the internal hydroxyl protons was seen with increasing methanol concentration. These results indicate that the morphology and chemical structure of the membranes have an effect on their solvent sorption and diffusion characteristics. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3277–3284, 2000     

Synthesis and properties of a new fluorine‐containing polybenzimidazole for high‐temperature fuel‐cell applications

An amorphous, organosoluble, fluorine‐containing polybenzimidazole (PBI) was synthesized from 3,3′‐diaminobenzidine and 2,2‐bis(4‐carboxyphenyl)hexafluoropropane. The polymer was soluble in N‐methylpyrrolidinone and dimethylacetamide and had an inherent viscosity of 2.5 dL/g measured in dimethylacetamide at a concentration of 0.5 g/dL. The 5% weight loss temperature of the polymer was 520 °C. Proton‐conducting PBI membranes were prepared via solution casting and doped with different amounts of phosphoric acid. In the methanol permeability measurement, the PBI membranes showed much better methanol barrier ability than a Nafion membrane. The proton conductivity of the acid‐doped PBI membranes increased with increasing temperatures and concentrations of phosphoric acid in the polymer. The PBI membranes showed higher proton conductivity than a Nafion 117 membrane at high temperatures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4508–4513, 2006     

Nanofiltration membranes based on poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(styrene sulfonic acid)

Graft copolymers comprising poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA were synthesized using atom transfer radical polymerization (ATRP) for composite nanofiltration (NF) membranes. Direct initiation of the secondary chlorinated site of CTFE units facilitates grafting of PSSA, as revealed by FT‐IR spectroscopy. The successful “grafting from” method and the microphase‐separated structure of the graft copolymer were confirmed by transmission electron microscopy (TEM). Wide angle X‐ray scattering (WAXS) also showed the decrease in the crystallinity of P(VDF‐co‐CTFE) upon graft copolymerization. Composite NF membranes were prepared from P(VDF‐co‐CTFE)‐g‐PSSA as a top layer coated onto P(VDF‐co‐CTFE) ultrafiltration support membrane. Both the rejections and the flux of composite membranes increased with increasing PSSA concentration due to the increase in SO₃H groups and membrane hydrophilicity, as supported by contact angle measurement. The rejections of NF membranes containing 47 wt% of PSSA were 83% for Na₂SO₄ and 28% for NaCl, and the solution flux were 18 and 32 L/m² hr, respectively, at 0.3 MPa pressure. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface modified multi‐walled carbon nanotubes and Nafion nanocomposite membranes for use in fuel cell applications

The preparation and characterization of the nanocomposite polyelectrolyte membranes, based on Nafion, sulfonated multi‐walled carbon nanotubes (MWCNT‐SO₃H) and imidazole modified multi‐walled carbon nanotubes (MWCNT‐Im), for direct methanol fuel cell applications is described. The results showed that the modification of multi‐walled carbon nanotubes (MWCNT) with proton‐conducting groups (sulfonic acid groups or imidazole groups) could enhance the proton conductivity of the nanocomposite membranes in comparison to Nafion 117. Regarding the interactions between the protonated imidazole groups, grafted on the surface of MWCNT, and the negatively charged sulfonic acid groups of Nafion, new electrostatic interactions can be formed in the interface of the Nafion and MWCNT‐Im, which result in both lower methanol permeability and higher proton conductivity. The physical characteristics of these manufactured nanocomposite membranes were investigated by thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, water uptake, methanol permeability, and ion exchange capacity, as well as proton conductivity. The Nafion/MWCNT‐Im membranes showed the higher proton conductivity, lower methanol permeability, and, as a consequence, a higher selectivity parameter in comparison to the neat Nafion or Nafion membrane containing MWCNT‐SO₃H or ─OH functionalized multi‐walled carbon nanotubes (MWCNT‐OH) membranes. The obtained results indicated that the Nafion/MWCNT‐Im membranes could be used as efficient polyelectrolyte membranes for direct methanol fuel cell applications.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Composite polymer electrolyte membranes comprising P(VDF‐co‐CTFE)‐g‐PSSA graft copolymer and zeolite for fuel cell applications

Hybrid organic/inorganic composite polymer electrolyte membranes based on a poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) grafted membrane and varying concentrations of zeolite were investigated for application in proton exchange membrane fuel cells (PEMFC). A proton conducting comb copolymer consisting of poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) (PSSA) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA (graft copolymer) with 47 wt% of PSSA was synthesized using atom transfer radical polymerization (ATRP) and solution blended with zeolite. Upon incorporation of zeolite, the symmetric stretching band of both SO group (1169 cm^?1) and the ? OH group (3426 cm^?1) shifted to lower wavenumbers. The shift in these FT‐IR spectra suggests that the zeolite particles strongly interact with the sulfonic acid groups of PSSA chains. When the weight percent of zeolite 5A is above 7%, the proton conductivity at room temperature was reduced to 0.011 S/cm. The water uptake of the composite membranes decreased from 234 to 125% with an increase of the zeolite 5A weight percent to 10 wt%. The decrease in water uptake is likely a result of the decrease in the number of available water absorption sites because of the hydrogen bonding interactions between the zeolite particles and the graft copolymer matrix. This behavior is successfully investigated by scanning electron microscopy (SEM). The results of thermal gravimetric analysis (TGA) also showed that all the membranes were stable up to 300°C. Copyright © 2009 John Wiley & Sons, Ltd.     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Polymeric proton conducting membranes for medium temperature fuel cells (110–160°C)

The availability of stable polymeric membranes with good proton conductivity at medium temperatures is very important for the development of methanol PEM fuel cells. In view of this application, a systematic investigation of the conductivity of Nafion 117 and sulfonated polyether ether ketone (S-PEEK) membranes was performed as a function of relative humidity (r.h.) in a wide range of temperature (80–160°C). The occurrence of swelling/softening phenomena at high r.h. values prevented conductivity determinations above certain temperatures. Nevertheless, when r.h. was maintained at values lower than 80%, measurements were possible up to 160°C. The results showed that Nafion is a better proton conductor than S-PEEK at low r.h. values, especially at temperatures lower than 120°C. The differences in conductivity were, however, leveled out with the increasing r.h. and temperature. While at 100°C and 35% r.h. the conductivity of S-PEEK 2.48 was about 30 times lower than the conductivity of Nafion, both membranes reached a comparable conductivity (4×10⁻² S cm⁻¹) at 160°C and 75% r.h. The effect of superacidity and crystallization of the polymers on the conductivity, as well as the possibility of using Nafion and S-PEEK membranes in medium temperature fuel cells, are discussed.     

Grain‐Boundary‐Free Super‐Proton Conduction of a Solution‐Processed Prussian‐Blue Nanoparticle Film

A porous crystal family has been explored as alternatives of Nafion films exhibiting super‐proton conductivities of ≥10⁻² S cm⁻¹. Here, the proton‐conduction natures of a solution‐processed film of nanoparticles (NPs) have been studied and compared to those of a Nafion film. A mono‐particle film of Prussian‐blue NPs is spontaneously formed on a self‐assembled monolayer substrate by a one‐step solution process. A low‐temperature heating process of the densely packed, pinhole‐free mono‐particle NP film enables a maximum 10⁵‐fold enhancement of proton conductivity, reaching ca. 10⁻¹ S cm⁻¹. The apparent highest conductivity, compared to previously reported data of the porous crystal family, remains constant against humidity changes by an improved water‐retention ability of the film. In our proposed mechanism, the high‐performing solution‐processed NP film suggests that heating leads to the self‐restoration of hydrogen‐bonding networks throughout their innumerable grain boundaries.     

Nafion–polyfurfuryl alcohol nanocomposite membranes for direct methanol fuel cells

Commercial Nafion 115 membranes were successfully modified by in situ acid-catalyzed polymerization of furfuryl alcohol (PFA) within Nafion structures. FT-IR and AFM were used to characterize the chemical and morphological structures of the Nafion–PFA nanocomposite membrane obtained. The methanol permeation experiments showed that the methanol flux through the Nafion–PFA nanocomposite membranes dropped by a factor of 2.2–2.7 when PFA loading was 3.9–8.0 wt.%. Importantly, the proton conductivity of the membranes decreased only slightly at a low PFA loading (<8 wt.%). The nanocomposite membranes with higher selectivity (e.g., proton conductivity/methanol crossover) achieved a much higher DMFC performance at both room temperature and 60 °C.     

直接甲醇燃料电池新型聚合物膜的研究

通过溶液共混方法 ,制备了聚偏氟乙烯与聚苯乙烯磺酸 (PVDF_PSSA)、聚偏氟乙烯与Nafion(PVDF_Nafion)两种共混膜 .研究了膜组成对膜电导率和甲醇透过率的影响 .与Nafion 1 1 7膜相比 ,PVDF_Nafion共混膜在Nafion含量为 2 5wt%时 ,电导率σ下降 2个数量级 ,而甲醇透过率P却降低 3个数量级 .若以 (σ/P)为综合指标 ,则PVDF_Nafion共混膜和PVDF_PSSA共混膜的综合性能分别比Nafion 1 1 7膜高约 4 0倍、1 6倍     

Nanocomposite fuel cell membranes based on Nafion and acid functionalized zeolite beta nanocrystals

We have prepared nanocomposite proton exchange membranes (PEMs) based on Nafion with sulfonic acid functionalized zeolite beta (AFB) as an additive. 2.5 and 5 wt% AFB composite membranes possess proton conductivity/methanol permeability (selectivity) ratios as much as 93% higher than commercial Nafion 117 at 21 °C, and 63% higher at 80 °C. These 2.5 and 5 wt% AFB composite membranes also outperform commercial Nafion 117 in direct methanol fuel cell performance evaluations. The composite membranes are characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, four-electrode impedance for proton conductivity, two-compartment permeation for methanol crossover, and direct methanol fuel cell performance.     

Radiation-induced grafting of styrene onto ultra-high molecular weight polyethylene powder and subsequent film fabrication for application as polymer electrolyte membranes: I. Influence of grafting conditions

Ultra-high molecular weight polyethylene (UHMWPE) powder was irradiated by gamma rays using a ⁶⁰Co source. Simultaneous and pre-irradiation grafting was performed in air and in inert atmosphere at room temperature. The monomer selected for grafting was styrene, since the styrene-grafted UHMWPE could be readily post-sulfonated to afford proton exchange membranes (PEMs). The effect of absorbed radiation dose and monomer concentration in methanol on the degree of grafting (DG) is discussed. It was found that the DG increases linearly with increase in the absorbed dose, grafting time and monomer concentration, reaching a maximum at a certain level. The order of rate dependence of grafting on monomer concentration was found to be 2.32. Furthermore, the apparent activation energy, calculated by plotting the Arrhenius curve, was 11.5 kJ/mole. Lower activation energy and high rate dependence on monomer concentration shows the facilitation of grafting onto powder substrate compared with film. The particle size of UHMWPE powder was measured before and after grafting and found to increase linearly with increase in level of grafting. FTIR-ATR analysis confirmed the styrene grafting. The grafted UHMWPE powder was then fabricated into film and post-sulfonated using chlorosulfonic acid for the purposes of evaluating the products as inexpensive PEM materials for fuel cells. The relationship of DG with degree of substitution (DS) of styrene per UHMWPE repeat unit and ion exchange capacity (IEC) is also presented.     

改性聚偏氟乙烯接枝共混聚苯乙烯磺酸膜的制备与性能

将苯乙烯添加到溶有原硅酸钠改性的聚偏氟乙烯(PVDF)N-甲基吡咯烷酮溶液中, 以过氧化苯甲酰(BPO)作引发剂, 苯乙烯直接接枝到原硅酸钠改性的PVDF链上, 成膜后磺化制备了聚偏氟乙烯接枝苯乙烯(PVDF-g-PSSA)膜. 采用傅立叶变换红外光谱(FT-IR)、扫描电镜(SEM)、能量扩散X射线(EDX)和多功能材料实验机表征了膜的结构、形貌及硫和硅的分布、机械强度、溶胀度, 使用阻抗分析和气相色谱仪研究了苯乙烯含量(w)对PVDF-g-PSSA膜的质子导电性能和阻醇性能的影响. 结果表明, 苯乙烯加入后, 原硅酸钠改性的PVDF与苯乙烯进行接枝共聚反应, 苯乙烯磺化反应不只是在膜表面进行, 同时渗入到膜中进行, 机械性能得到了改善. 质子电导率(σ)随苯乙烯质量分数的提高而升高. Na4SiO4为8%和苯乙烯为20%的PVDF-g-PSSA膜, 在25 ℃时溶胀度仅为20.4%, 甲醇透过系数在10-7 cm2·s-1数量级上, 比Nafion115膜的低一个数量级. 该膜具有较高的选择性, 在直接甲醇燃料电池中具有良好的应用前景.     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Solvent‐free fabrication of proton‐conducting membranes based on commercial elastomers

Five different types of elastomers were examined as the matrix materials in the preparation of non‐fluorinated proton exchange membranes utilizing a solvent‐free route via the in situ reaction of sodium 4‐styrenesulfonate (NaSS). The morphology of the elastomer/NaSS vulcanizates was studied to evaluate the effect of polarity, viscosity and saturation degree of the elastomer matrixes. Much better dispersion of NaSS was found in chlorosulfonated polyethylene rubber (CSM) and hydrogenated nitrile butadiene rubber (HNBR) matrixes than in the other three types of elastomer matrixes. For CSM/NaSS and HNBR/NaSS proton exchange membranes, distinctive membrane properties were observed and correlated with their different structure and morphologies. The CSM/NaSS membranes exhibited the proton conductivity as high as ~0.03 S cm^?1 and the selectivity (the ratio of proton conductivity to methanol permeability) higher than that of Nafion. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104