Polystyrene‐b‐poly(2,2,2‐trifluoroethyl acrylate)‐b‐polystyrene copolymers: Synthesis and fabrication of their hydrophobic porous films,spheres, and fibers

New block copolymers Polystyrene‐b‐poly (2,2,2‐trifluoroethyl acrylate)‐b‐Polystyrene (PS‐PTFEA‐PS) with controlled molecular weight (M_n=5000‐11000 g?mol^?1) and narrow molecular weight distribution (M_w/M_n=1.13‐1.17) were synthesized via RAFT polymerization. The molecular structure and component of PS‐PTFEA‐PS block copolymers were characterized through ¹H NMR, ¹⁹F NMR, GPC, FT‐IR and elemental analysis. The porous films of such copolymers with average pore size of 0.80‐1.34 μm and good regularity were fabricated via a static breath‐figure (BF) process. The effects of solvent, temperature, and polymer concentration on the surface morphology of such film were investigated. In addition, microstructured spheres and fibers of such block copolymers were fabricated by electrospinning process and observed by scanning electron microscopy (SEM). Furthermore, the hydrophobicity of porous films, spheres, and fibers was investigated. The porous film showed a good hydrophobicity with the water‐droplet contact angles of 129°, and the fibers showed higher hydrophobicity with the water‐droplet contact angles of 142°. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 678–685     

Preparation of a superhydrophobic rough surface

The relationship between the contact angles, surface tension, and surface roughness is reviewed. Numerical formulas related to the superhydrophobic rough surfaces of polymers are predicted with two approaches, the Wenzel and Cassie–Baxter models. With these models as a guide, an artificial superhydrophobic surface is created. Rough nylon surfaces mimicking the lotus leaf are created by the coating of a polyester surface with nylon‐6,6 short fibers via the flocking process. Poly(acrylic acid) chains aregrafted onto nylon‐6,6 surfaces, and this is followed by the grafting of 1H,1H‐perfluorooctylamine onto the poly(acrylic acid) chains. Water contact angles as high as 178° are achieved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 253–261, 2007.     

Low‐rate dynamic contact angles on poly(methyl methacrylate/ethyl methacrylate, 30/70) and the determination of solid surface tensions

Low‐rate dynamic contact angles of 12 liquids on a poly(methyl methacrylate/ethyl methacrylate, 30/70) P(MMA/EMA, 30/70) copolymer were measured by an automated axisymmetric drop shape analysis‐profile (ADSA‐P). It was found that five liquids yield nonconstant contact angles, and/or dissolve the polymer on contact. From the experimental contact angles of the remaining seven liquids, it is found that the liquid–vapor surface tension times cosine of the contact angle changes smoothly with the liquid–vapor surface tension (i.e., γ_l|Kv cos θ depends only on γ_l|Kv for a given solid surface or solid surface tension). This contact angle pattern is in harmony with those from other methacrylate polymer surfaces previously studied.^45,50 The solid–vapor surface tension calculated from the equation‐of‐state approach for solid–liquid interfacial tensions¹⁴ is found to be 35.1 mJ/m², with a 95% confidence limit of ± 0.3 mJ/m², from the experimental contact angles of the seven liquids. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2039–2051, 1999     

Synthesis and characterization of organic/inorganic hybrid star polymers of 2,2,3,4,4,4‐hexafluorobutyl methacrylate and octa(aminophenyl)silsesquioxane nano‐cage made via atom transfer radical polymerization

Well‐defined organic/inorganic hybrid fluorinated star polymers were synthesized via atom transfer radical polymerization (ATRP) of 2,2,3,4,4,4‐hexafluorobutyl methacrylate (HFBMA) using octa(aminophenyl)silsesquioxane (OAPS) nano‐cage as initiator. For this purpose, OAPS was transformed into ATRP initiator by reacting with 2‐bromoisobutyrylbromide. ATR polymerization of HFBMA was carried out in trifluorotoluene at 75 °C using CuCl/2,2‐bipyridine or N,N,N′,N″,N″‐pentamethyldiethylenetriamine as catalyst system. GPC and ¹H NMR data confirmed the synthesis of OAPS/PHFBMA hybrid star polymer. Kinetics of the ATR polymerization of HFBMA using OAPS nano‐cage initiator was also investigated. The OAPS/PHFBMA hybrid stars were found to be molecularly dispersed in solution (THF); however, TEM micrographs revealed the formation of spherical particles of ～ 120–180 nm by the OAPS/PHFBMA hybrid star polymer after solvent evaporation. Thermal characterization of the nanocomposites by differential scanning calorimetry (DSC) revealed a slightly higher glass transition temperature (T_g) (when compared with the linear PHFBMA) of higher molecular weight OAPS/PHFBMA hybrid star polymers. In contrast, lower T_g than the linear PHFBMA was observed for OAPS/PHFBMA of relatively lower molecular weight (but higher than the linear PHFBMA). Thermal gravimetric analysis (TGA) showed a significant retardation (by ～60 °C) in thermal decomposition of nanocomposites when compared with the linear PHFBMA. Additionally, surface properties were evaluated by measuring the contact angles of water on polymer surfaces. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7287–7298, 2008     

Effect of silane coupling agent on mechanical interfacial properties of glass fiber‐reinforced unsaturated polyester composites

A silane coupling agent, γ‐methacryloxypropyltrimethoxysilane, for the surface modification of glass fibers was varied between 0.1 and 0.8 wt %. To understand the role of interfacial adhesion of glass fiber/unsaturated polyester composites, contact angles of the silane‐treated glass fibers were measured by the wicking method on the basis of the modified Washburn equation with deionized water, diiodomethane, and ethylene glycol as testing liquids. As a result, silane‐treated glass fibers led to increased surface free energy, mainly because of their increased specific or polar component. The mechanical interfacial behaviors based on the interlaminar shear strength (ILSS) of the composites determined by short‐beam tests and the critical stress‐intensity factor (K_IC) were also improved in the case of silane‐treated composites. The surface free energy and the mechanical interfacial properties especially showed the maximum value in the presence of 0.4 wt % silane coupling agent. It revealed that the increase of a specific component of the surface free energy or hydrogen bonding between the glass fibers and the coupling agents plays an important role in improving the degree of adhesion at interfaces in a composite system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 55–62, 2003     

Stimuli‐responsive antifouling polyisobutylene‐based biomaterials via modular surface functionalization

This article demonstrates a new, modular approach to surface functionalization that harnesses chain entanglement. A layer of functionalized polyisobutylene, (PIB)‐ω, where ω = ‐OH, ‐thymine (T), ‐hexaethylene glycol (HEG), poly(ethylene glycol) (‐PEG‐OH), methoxy‐functionalized poly(ethylene glycol) (‐PEG‐OCH₃), and ‐tetraethylene glycol‐α‐lipoate (TEG‐αL) was adhered to PIB‐based thermoplastic elastomer (TPE) surfaces. X‐ray photoelectron spectroscopy (XPS) at angles ranging from 20° to 75° showed decreasing polar group concentration with increasing penetration depth, confirming segregation of polar groups toward the surface. Water contact angle (WCA) of the PIB‐based TPE dropped from 95° to 79°?83° upon coating, and soaking in water for 24 h further decreased the WCA. Dynamic WCA measurements showed 40–30° receding angles, showing that stimulus from an aqueous environment elicits enrichment of polar groups on the surface. Fibrinogen (Fg) adsorption on the various surfaces was quantified using surface plasmon resonance (SPR). Static and dynamic WCA did not vary significantly among TPE + PIB‐ω surfaces, but there were dramatic differences in Fg adsorption: 256 ng/cm² was measured on the native TPE, which dropped to 40 and 22 ng/cm² on PIB‐PEG‐OCH₃ and PIB‐PEG‐OH‐coated surfaces. PIB‐TEG‐αL‐coated surfaces presented the lowest Fg adsorption with 14 ng/cm². © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1742–1749     

Surface methacrylation and graft copolymerization of ultrafine cellulose fibers

Ultrafine fibrous (? from 100 to 450 nm) cellulose membranes were generated by electrospinning of cellulose acetate [degree of substitution (DS): 2.45, weight‐average molecular weight: 30,000 Da], followed by alkaline deacetylation. Reaction of these ultrahigh surface‐area cellulose fibers with methacrylate chloride (MACl) produced activated surfaces without altering the fiber morphology. Surface methacrylation of these fibers was confirmed by the acquired hydrophobicity (θ_water = 84°) as compared to the originally hydrophilic (θ_water = 56°) cellulose. Changing the MACl:OH molar ratios could vary the overall DS of methacrylation. The very low overall DS values indicate the surface nature of the methacrylation reaction. At a DS of 0.17, the thermal properties of the surface methacrylated cellulose resemble those of cellulose derivatives at much higher DS values, an unusual behavior of the ultrafine fibers. The methacrylated cellulose could be further copolymerized with vinyl monomers (methyl methacrylate, acrylamide, and N‐isopropylacrylamide) as linear grafts or three‐dimensional (3D) networks. The morphology of cellulose fibers and the interfiber pore structure were not altered at 15–33% graft levels. This study demonstrates that either linear or 3D networks of vinyl polymers could be efficiently supported on ultrafine cellulose fibrous membranes via surface methacrylation. Through these surface reactions the chemical, thermal, and liquid wetting and absorbent properties of these ultrafine fibrous membranes were significantly altered with no change to the fiber dimensions or interfiber pore morphology. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 953–964, 2003     

Preparation of emulsion‐templated fluorinated polymers and their application in oil/water separation

A series of emulsion‐templated fluorinated polymers (polyHIPEs) were first synthesized with introducing 2‐(perfluorohexyl)ethyl methacrylate (PEM) to the external phase of water‐in‐styrene high internal phase emulsion (HIPE) templates. The morphology (i.e., void size and its distribution) of these porous materials could be tuned simply by changing PEM and/or surfactant amount. The synergistic effect between the surface chemistry and surface architecture allowed the polyHIPEs to possess hydrophobicity with a water contact angle of 151°. The superhydrophobicity and oleophilicity of the polyHIPEs, together with their highly open porous structure, make the material a very competitive candidate as a filtration material for oil/water separation in practice with the efficiency of separating dichloromethane from the oil/water mixture of 95%. Such oil/water separating capacity was maintained after 10 cycles of filtration of oil/water, indicating the cyclic usage of the polyHIPE is feasible. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1508–1515     

Synthesis of urea‐containing ABA triblock copolymers: Influence of pendant hydrogen bonding on morphology and thermomechanical properties

Reversible addition‐fragmentation chain transfer (RAFT) polymerization produced novel ABA triblock copolymers with associative urea sites within pendant groups in the external hard blocks. The ABA triblock copolymers served as models to study the influence of pendant hydrogen bonding on polymer physical properties and morphology. The triblock copolymers consisted of a soft central block of poly(di(ethylene glycol) methyl ether methacrylate) (polyDEGMEMA, 58 kg/mol) and hard copolymer external blocks of poly(2‐(3‐hexylureido)ethyl methacrylate‐co‐2‐(3‐phenylureido)ethyl methacrylate) (polyUrMA, 18‐116 kg/mol). Copolymerization of 2‐(3‐hexylureido)ethyl methacrylate (HUrMA) and 2‐(3‐phenylureido)ethyl methacrylate (PhUrMA) imparted tunable hard block T_g's from 69 to 134 °C. Tunable hard block T_g's afforded versatile thermomechanical properties for diverse applications. Dynamic mechanical analysis (DMA) of the triblock copolymers exhibited high modulus plateau regions (∼100 MPa) over a wide temperature range (−10 to 90 °C), which was indicative of microphase separation. Atomic force microscopy (AFM) confirmed surface microphase separation with various morphologies. Variable temperature FTIR (VT‐FTIR) revealed the presence of both monodentate and bidentate hydrogen bonding, and pendant hydrogen bonding remained as an ordered structure to higher than expected temperatures. This study presents a fundamental understanding of the influence of hydrogen bonding on polymer physical properties and reveals the response of pendant urea hydrogen bonding as a function of temperature as compared to main chain polyureas. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1844–1852     

Synthesis and properties of ultralow dielectric porous polyimide films containing adamantane

A series of novel ultralow dielectric porous polyimide (PI) films containing adamantane groups was prepared via the thermolysis of polyethylene glycol (PEG) oligomers mixed into PI matrix. Scanning electron microscopy results indicated that the porous PI films showed closed pores with an average diameter of 120 ± 10 nm. Good thermal properties with 5% weight loss temperature of 499 °C in air atmosphere and glass transition temperature in excess of 310 °C were shown for porous PI films. Notably, the ultralow dielectric constant of porous PI films with 1.85 at 1 MHz was obtained and revealed via broadband dielectric spectroscopy. The effects of the chemical structure of the PI matrix and PEG content on the decomposition behavior of PEG and the performance of porous films were investigated. Wide‐angle X‐ray diffraction results indicated that the PI matrix with large d‐spacing generated weaker interactions between the PEG and PI backbone than those of PI matrix with small d‐spacing. As a result, the PEG for the PI matrix with large d‐spacing was completely decomposed. As indicated by the broadband dielectric spectroscopy results, lower dielectric porous PI films were prepared when the PEG contents in the PI matrix increased from 0 to 20 wt %. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 549–559     

Polyurethane elastomers based on amphiphilic poly(caprolactone)‐b‐poly(butadiene)‐b‐poly(caprolactone) triblockcopolyols

Hydroxyl‐terminated poly(butadiene) (HTPB; M_n = 2100 g mol⁻¹) was capped with 30 and 60 wt % of ɛ‐caprolactone to reach amphiphilic triblock copolymers in form of capped poly(butadiene) CPB. The former (CPB30; M_n = 3300 g/mol) is amorphous with a glass temperature of −56 °C. CPB60 (M_n = 4000 g mol⁻¹) is semi‐crystalline with a melting point of 50 °C and a glass transition at −47 °C. The CPBs, HTPB and polycaprolactone diol (M_n = 2000 g mol⁻¹) were used as soft segment components in the preparation of polyurethane elastomers (PUE), using a 1/1 mixture of an MDI prepolymer and uretonimine modified MDI, and hard phase components in form of 1,3‐propane diol, 1,4‐butane diol, and 1,5‐pentane diol. CPB‐based elastomers with 1,4 butane diol (8 wt %) show hard domains as fringed aggregates with a better connection to the continuous phase than the HTPB‐based PUE. The soft segment glass transition temperature (T_g) is at −28 °C for HTPB‐based PUE and at −43 °C for those of CPB. The tensile strength of the CPB30&60‐based PUE is found between 20 and 30 MPa at an elongation at break of 400% and 550%, respectively. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1162–1172     

Tadpole‐shaped amphiphilic copolymers prepared via RAFT polymerization and click reaction

The tadpole‐shaped amphiphilic copolymers with cyclic polystyrene as the head and a linear poly(N‐isopropylacrylamide) as the tail have been successfully synthesized by combination of reversible addition‐fragmentation chain transfer (RAFT) polymerization and “click” reaction. The synthesis involves two main steps: (1) preparation of a linear acetylene‐terminated PNIPAAM‐b‐PS with a side azido group anchored at the junction between two blocks; (2) intramolecular cyclization reaction to produce the cyclic PS block using “click” chemistry under high dilution. The structures, molecular weights, and molecular weight distributions of the resulted intermediates and the target polymers were characterized by their ¹H NMR, FTIR, and gel permeation chromatography. The difference of surface property between tadpole‐shaped polymer and its linear precursor was observed, and the water contact angles on the former surface are larger than that of the latter surface. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2390–2401, 2008     

Surface modification and characterization of SEBS films obtained by in situ and ex situ oxidization with potassium permanganate

The surface morphologies and compositions of the asymmetric films of polystyrene‐b‐poly(ethylene‐co‐butylene)‐b‐polystyrene (SEBS) prepared by in situ and ex situ oxidization with the KMnO₄ aqueous solution and KMnO₄/H₂SO₄ mixed solution were investigated by using scanning electron microscope, atomic force microscope (AFM), X‐ray photoelectron spectroscopy (XPS) and attenuated total reflectance infrared spectroscopy (ATR‐FTIR). The effect of the oxidization reagents on morphological changes and the influence of in situ and ex situ preparation methods on surface compositions were discussed. Different from the in situ oxidation by degrading the copolymers to form a gradient film, the ex situ oxidation preferentially degraded the uppermost layer of the film. Although both the KMnO₄ oxidation and the KMnO₄/H₂SO₄ oxidation gave hierarchical structures, distinctive differences were found that large ridges and smaller granules were fabricated in the former film and the latter produced large and deep ravines and fine sponge‐like morphologies. Additionally, the oxygen concentration and the oxo‐species implanted by these oxidation treatments were characterized and evaluated to provide a quantitative comparison. Oxygen, as well as manganese was found to be implanted in the surface layer of the oxidized film, forming predominantly O? C and O? C?O groups, as well as a small fraction of O? H and Mn? O compounds. Changes in contact angle of water on these films and total surface oxygen content are related but not directly. The hystereses of water contact angle at a value of 119 ± 3° due primarily to surface roughness and at a value of 63 ± 3° due primarily to chemical heterogeneity are led by different oxidation degrees and oxidation methods. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Preparation of hierarchically structured PCL superhydrophobic membrane via alternate electrospinning/electrospraying techniques

Superhydrophobic polycaprolactone (PCL) membranes with hierarchical structure were fabricated via alternate electrospinning/electrospraying techniques. Electrospun PCL/methyl silicone oil (PCL/MSO) nanofibers were employed as substrate. PCL/MSO‐PCL microspheres (PCL/MSO‐PCL_MS) hierarchical membrane was prepared via electrosprayed PCL_MS as an additional layer on the substrate. Field emission scanning electron microscopy images showed the formation of hierarchical PCL/MSO‐PCL_MS membranes. Compared to pure PCL fibers substrate (120 ± 1.3°), the water contact angle (WCA) of MSO‐modified PCL membrane was 142 ± 0.7°. The most interesting observation was that the WCA of PCL_MS without any modification could be achieved to 146 ± 2.8°. On this basis, PCL/MSO‐PCL_MS hierarchical membrane possessed superhydrophobic surface with 150 ± 0.6° of WCA. The excellent surface roughness and air‐pocket capacity of hierarchical membranes would make the membranes more hydrophobic. The maximum oil (n‐hexane) adsorption capacity of PCL/MSO‐PCL_MS membrane was 32.53 g g^?1. Oil–water separation efficiencies of the superhydrophobic membranes were all higher than 99.93% after 10 cycles. The hierarchically structured PCL superhydrophobic membranes indicate the potential applications of environmentally friendly biopolymers as separation membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 421–430     

A new route to phosphonium polymer network solids via cyclotrimerization

An organo‐main group network solid having tetrahedral phosphonium vertices was prepared from a diacetyl monomer via a straightforward cyclotrimerization reaction. The network solid composition was examined by FT‐IR spectroscopy and elemental microanalysis, revealing quantitative reaction of carbonyl moieties and a 67% degree of cross‐linking. The reaction yielded a material having a layered structure that is comprised of an amorphous polymer and which is thermally stable up to 370 °C in air with a char yield of 40% upon heating as high as 800 °C under N₂. The polymer is stable to 6 M NaOH(aq ) at 60 °C for 24 h and takes up only 10.63% of water by mass at room temperature. The surface morphology, as examined by AFM, revealed a very smooth as‐prepared film (RMS roughness of 3 nm). The specific surface area measured by BET analysis with N₂ gas is 9 m² g^?1, indicating a type II, nonporous material. Physisorption with CO₂ revealed that the phosphonium network solid has additional affinity for CO₂, suggesting that such materials may have use for applications such as CO₂ capture. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1620–1625     

Mesoporous Anatase TiO2 Nanorods as Thermally Robust Anode Materials for Li‐Ion Batteries: Detailed Insight into the Formation Mechanism

Uniformly mesoporous and thermally robust anatase nanorods were produced with quantitative yield by a simple and efficient one‐step approach. The mechanism of this process was revealed by insertion of Eu³⁺ cations from the reaction medium as luminescent probes. The obtained structure displays an unusually high porosity, an active surface area of about 300 m²g^?1 and a specific capacity of 167 mA h g^?1 at a C/3 rate, making it attractive as an anode electrode for Li‐ion batteries. An additional attractive feature is its remarkable thermal stability; heating to 400 °C results in a decrease in the active surface area to a still relatively high value of 110 m² g^?1 with conservation of open mesoporosity. Thermal treatment at 800 °C or higher, however, causes transformation into a non‐porous rutile monolith, as commonly observed with nanoscale titania.     

Synthesis and characterization of highly fluorinated poly(phthalazinone ether)s based on AB‐type monomers

Four different fluorinated methyl‐ and phenyl‐substituted 4‐(4‐hydroxyphenyl)‐2‐(pentafluorophenyl)‐phthalazin‐1(2H)‐ones, AB‐type phthalazinone monomers, have been successfully synthesized by nucleophilic addition–elimination reactions of methyl‐ and phenyl‐substituted 2‐((4‐hydroxy)benzoyl)benzoic acid with 1‐(pentafluorophenyl)hydrazine. Under mild reaction conditions, the AB‐type monomers underwent self‐condensation polymerization reactions successfully and gave fluorinated poly(phthalazinone ether)s with high molecular weights. Detailed structural characterization of the AB‐type monomers and fluorinated polymers was determined by ¹H NMR, ¹⁹F NMR, FTIR, and GPC. The solubility, thermal properties, mechanical properties, water contact angles, and optical absorption of the polymers were evaluated. The polymers had high T_gs varying from 337 to 349 °C and decomposition temperatures (T_{d, 25} wt %) above 409 °C. Tough, flexible films were cast from THF and chloroform solutions. The films showed excellent tensile strengths ranging from 70 to 85 MPa with good hydrophobicities with water contact angles higher than 95.5 °C. The polymers had absorption edges below 340 nm and very low absorbance per cm at higher wavelengths 500–2500 nm. These results indicate that the polymers are promising as high performance materials, for example, membranes and hydrophobic materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1761–1770     

Silicon surface modification with trialkoxysilyl‐functionalized star‐shaped polymers

The synthesis of trimethoxysilane end‐capped linear polystyrene (PS) and star‐branched PS and subsequent silicon (Si) surface modification with linear and star polymers are described. Trimethoxysilane terminated PS was synthesized using sec‐butyl lithium initiated anionic polymerization of styrene and subsequent end‐capping of the living anions with p‐chloromethylphenyl trimethoxysilane (CMPTMS). ¹H and ²⁹Si NMR spectroscopy confirmed the successful end‐capping of polystyryllithium with the trimethoxysilane functional group. The effect of a molar excess of end‐capper on the efficiency of functionalization was also investigated, and the required excess increased for higher molar mass oligomers. Acid catalyzed hydrolysis and condensation of the trimethoxysilane end‐groups resulted in star‐branched PS, and NMR spectroscopy and SEC analysis were used to characterize the star polymers. This is the first report of core‐functionalized star‐shaped polymers as surface modifiers and the first comparative study showing differences in surface topography between star and linear polymer modified surfaces. Surface‐sensitive techniques such as ellipsometry, contact angle goniometry, and AFM were used to confirm the attachment of star PS, as well as to compare the characteristics of the star and linear PS modified Si surfaces. The polymer film properties were referenced to polymer dimensions in dilute solution, which revealed that linear PS chains were in the intermediate brush regime and the star‐branched PS produced a surface with covalently attached chains in the mushroom regime. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3655–3666, 2005     

Surface‐initiated atom transfer radical polymerization from porous poly(tetrafluoroethylene) membranes using the C?F groups as initiators

This work reports the surface‐initiated atom transfer radical polymerization (ATRP) from hydrogen plasma‐treated porous poly(tetrafluoroethylene) (PTFE) membranes using the C? F groups as initiators. Hydrogen plasma treatment on PTFE membrane surfaces changes their chemical environment through defluorination and hydrogenation reactions. With the hydrogen plasma treatment, the C? F groups of the modified PTFE membrane surface become effective initiators of ATRP. Surface‐initiated ATRP of poly(ethylene glycol) methacrylate (PEGMA) is carried out to graft PPEGMA chains to PTFE membrane surfaces. The chain lengths of poly(PEGMA) (PPEGMA) grafted on PTFE surfaces increase with increasing the reaction time of ATRP. Furthermore, the chain ends of PPEGMA grown on PTFE membrane surfaces then serve as macroinitiators for the ATRP of N‐isopropylacrylamide (NIPAAm) to build up the PPEGMA‐b‐PNIPAAm block copolymer chains on the PTFE membrane surfaces. The chemical structures of the modified PTFE membranes are characterized using X‐ray photoelectron spectroscopy. The modification increases the surface hydrophilicity of the PTFE membranes with reductions in their water‐contact angles from 120° to 60°. The modified PTFE membranes also show temperature‐responsive properties and protein repulsion features owing to the presence of PNIPAAM and PPEGMA chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2076–2083, 2010