Study on the preparation and multiproperties of the polypyrrole films doped with different ions

Conducting polypyrrole (PPy) films doped with p‐toluene solfonate (pTS^?), perchlorate (ClO₄^?) and polyphosphate (PP^?) were electrochemically synthesized on the stainless steel SS‐304 and the Indium Tin Oxide (ITO) glass substrates successfully. The conducting polymer composite films were studied by Fourier transform infrared spectra, integrated thermal analysis system and scanning electron microscopy, respectively. Four‐point probe measurements and in situ nanotribolab system equipped with a nanoscale electrical contact resistance package were employed to analyze their electrical and mechanical properties. Results indicate that the film doped with PP^? ion showed the best thermal stability. For the ClO₄^? ion doped films, the glass transition occurred at 274.8 °C. The pTS^? ion doped film on the SS‐304 steel had a good conductivity, and there was a voltage barrier that ranged from ?1.25 to 1.9 V according to the current–voltage curves. Nanoindentation tests show that the mechanical properties of the PPy/pTS^? film and the PPy/PP^? film were better than that of PPy/ClO₄^? films. Copyright © 2012 John Wiley & Sons, Ltd.     

In situ film characterization of thermally treated microstructured conducting polymer films

Based on a low‐cost fabrication routine microstructured conducting polymer films of poly (dioctylfluorene‐co‐benzothiadiazole) (F8BT) are prepared without any heat treatment or vacuum steps. The influence of thermal annealing at temperatures below the glass transition temperature of F8BT on such microstructured channel structures is investigated. In the applied structuring routine, a F8BT film is spin coated on a channel‐type hard master structure and afterwards floated on a flat support. Thereby, the properties of the final polymeric structures, for example channel width and height, can be tuned by simply varying the polymer concentration in solution and using the same master structure. With in situ grazing incidence small angle X‐ray scattering and imaging ellipsometry the installed channel structure and the influence of thermal treatment are probed. A complex interplay between a macroscopic polymer flow (reduced channel heights) and a molecular rearrangement (formation of mesoscopic crystallites) takes place during thermal annealing. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Enhancing electrochromic contrast and redox stability of nanostructure polypyrrole film doped by heparin as polyanion in different solvents

Heparin‐doped polypyrrole (PPy‐Hep) and ‐doped polypyrrole (PPy‐ClO₄) films are synthesized onto FTO‐coated glass electrode in a potentiostatic electrochemical process with the aim of producing uniform, transparent, and adherent coating. The resultant polymers are characterized via cyclic voltammetry, scanning electron microscopy (SEM), and UV–vis absorption spectroscopy. SEM study indicates that the PPy‐Hep film to be composed of a continuous interlinked network of quasi spherical grains (50–80 nm in dimensions). The electrochromic properties of PPy‐Hep and PPy‐ClO₄ polymer films are compared to spectroelectrochemistry and switching studies. The effect of different solvents (water, propylene carbonate, and acetonitrile) on the electrochromic features of electropolymerized polymers has been investigated, and we find a very significant solvent effect. PPy‐Hep film exhibits switching time of 1 s and the maximum transmittance contrast (ΔT%) is 48% at 800 nm in water. In addition, presence of Hep causes drastic enhancement of electro‐optical stability of PPy. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3365–3371     

In situ polymerization and morphology of polypyrrole obtained in water‐soluble polymer templates

Several water‐soluble polymers were used as templates for the in situ polymerization of pyrrole to determine their effect on the generation of nanosized polypyrrole (PPy) particles. The polymers used include: polyvinyl alcohol (PVA), polyethylene oxide (PEO), poly(vinyl butyral), polystyrene sulfonic acid, poly(ethylene‐alt‐maleic anhydride) (PEMA), poly(octadecene‐alt‐maleic anhydride), poly(N‐vinyl pyrrolidone), poly(vinyl butyral‐co‐vinyl alcohol‐co‐vinyl acetate), poly(N‐isopropyl acrylamide), poly(ethylene oxide‐block‐propylene oxide), hydroxypropyl methyl cellulose, and guar gum. The oxidative polymerization of pyrrole was carried out with FeCl₃ as an oxidant. The morphology of PPy particles obtained after drying the resulting aqueous dispersions was examined by optical microscopy, and selected samples were further analyzed via atomic force microscopy. Among the template polymers, PVA was the most efficient in generating stable dispersions of PPy nanospheres in water, followed by PEO and PEMA. The average size of PPy nanospheres was in the range of 160 nm and found to depend on the molecular weight and concentration of PVA. Model reactions and kinetics of the polymerization reaction of pyrrole in PVA were carried out by hydrogen ¹H NMR spectroscopy using ammonium persulfate as an oxidant. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Ammonia Gas Sensor Using Polypyrrole‐Coated TiO2/ZnO Nanofibers

Highly porous polypyrrole (PPy)‐coated TiO₂/ZnO nanofibrous mat has been successfully synthesized. The core TiO₂/ZnO nanofibers have an average diameter of ca. 100 nm and the shell of ultrathin PPy layer has a thickness of ca. 7 nm. The NH₃ gas sensor using the as‐prepared material exhibited a fast response over a wide dynamic range and high sensitivity with a detection limit of 60 ppb (S/N=3). Compared to conventional pristine PPy film, the improved performance in NH₃ detection can be attributed to the free access of NH₃ to PPy and a minimized gas diffusion resistance through the ultrathin PPy layer.     

In situ intercalative polymerization of conducting polypyrrole/montmorillonite nanocomposites

Conducting polypyrrole (PPy)‐montmorillonite (MMT) clay nanocomposites have been synthesized by the in situ intercalative polymerization method. The PPy‐MMT nanocomposites are characterized by field‐emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), ultraviolet–visible (UV–vis) spectroscopy, thermogravimetric analysis (TGA), and Fourier‐transform infrared (FTIR) spectroscopy. XRD patterns show that after polymerization by the in situ intercalative method with ammonium persulfate and 1 M HCl, an increase in the basal spacing from 1.2 to 1.9 nm was observed, signifying that PPy is synthesized between the interlayer spaces of MMT. TEM and SEM micrographs suggest that the coexistence of intercalated MMT layers with the PPy macromolecules. FTIR reveals that there might be possible interfacial interactions present between the MMT clay and PPy matrix. The study also shows that the introduction of MMT clay results in thermal stability improvement of the PPy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2279–2285, 2008     

Acrylic polymer/silica hybrid for electron‐beam resists

An acrylic polymer/silica hybrid resist film was investigated for fabricating a microstructure by electron‐beam (EB) lithography. EB lithography on the hybrid thin film afforded a positive pattern whose depth corresponded to the EB exposure dose; this indicated that the hybrid was an analog resist and could fabricate a three‐dimensional microstructure. The resist film had high heat resistance and compatibility with the underlying quartz plate, probably because of the silica component. The acrylic polymer/(RSiO_1.5)_n hybrid film showed higher EB sensitivity than a film of the crosslinked acrylic polymer and an acrylic polymer/(SiO₂)_n hybrid. Atomic force microscopy observation of the hybrid film surface showed the homogeneous dispersion of the acrylic polymer and the silica components in the hybrid film. The acrylic polymer component was EB‐sensitive, whereas dispersing the acrylic polymer and silica components homogeneously also played an important role in increasing the EB sensitivity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2107–2116, 2006     

Synthesis of dual‐functional copolymer with orthogonally photosensitive groups

A dual‐functional copolymer, poly(4‐styrenesulfonyl azide‐co‐t‐butyl‐methacrylate), with built‐in photoacid labile and photocrosslinkable components was designed and synthesized by radical copolymerization. The mixture of copolymer and photoacid generators was spin coated on aminosilane treated Si wafers and polycarbonate (PC). When exposed to 365 nm UV light, photoacids were generated, which decomposed the acid labile groups, t‐butyl‐ester, to carboxylic acid in the exposed region, leading to drastic change of wettability from hydrophobic to hydrophilic after developing the film in an aqueous base solution. The patterned polymer film could be subsequently photoimmobilized on the substrate under 254 nm deep UV exposure through C? H insertion via exited azide groups. ¹H‐NMR and Fourier transform infrared spectra confirmed the synthesis of the copolymer, and the photodecomposition and photografting reactions occurred orthogonally at 365 and 254 nm, respectively, without interfering each other. On the patterned surfaces, including a hexagonal dot array and a gradient line array, we demonstrated selective wetting in the 365 nm exposed regions. On the gradient line array, we showed an interesting ratchet wetting pattern. Finally, we showed that the copolymer could be used to modify the wettability of PC while maintaining its high optical quality. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Syntheses and properties of hyperbranched polybenzoxazole by thermal cyclodehydration of hyperbranched poly[o‐(t‐butoxycarbonyl)amide] via A2 + B3 approach

The syntheses and properties of hyperbranched poly(o‐hydroxyamide) [poly(HAB‐BCC)‐ABP], poly[o‐(t‐butoxycarbonyl)amide] [poly(HAB‐BCC)‐ABP‐t‐BOC], and polybenzoxazole [poly(HAB‐cycloBCC)] were examined. Poly(HAB‐BCC)‐ABP was obtained from the polycondensation reaction of 3,3‐dihydroxy‐4,4′‐diaminobiphenyl (HAB) as an A₂‐monomer and 1,3,5‐benzenetricarboxylchloride (BCC) as a B₃‐monomer with 2‐amino‐4‐t‐butylphenol (ABP) in NMP in the presence of pyridine for 24 h. The reaction of poly(HAB‐BCC)‐ABP and di‐t‐buthylcarbonate (DiBOC) was performed to obtain the corresponding poly(HAB‐BCC)‐ABP‐t‐BOC with pendant t‐BOC groups. The thermal cyclodehydration of poly(HAB‐BCC)‐ABP‐t‐BOC was carried out in the film sate at 400 °C, affording the poly(HAB‐cyclo‐BCC) in quantitative yield. Furthermore, the solubilities and thermal properties of these polymers were examined. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3640–3649, 2006     

Solution‐processable and thermally cross‐linkable fluorene‐cored triple‐triphenylamines with terminal vinyl groups to enhance electroluminescence of MEH‐PPV: Synthesis,curing, and optoelectronic properties

This study reports the synthesis, curing, and optoelectronic properties of a solution‐processable, thermally cross‐linkable electron‐ and hole‐blocking material containing fluorene‐core and three periphery N‐phenyl‐N‐(4‐vinylphenyl)benzeneamine ( FTV ). The FTV exhibited good thermal stability with T_d above 478 °C in nitrogen atmosphere. The FTV is readily cross‐linked via terminal vinyl groups by heating at 160 °C for 30 min to obtain homogeneous film with excellent solvent resistance. Multilayer PLED device [ITO/PEDOT:PSS/cured‐ FTV /MEH‐PPV/Ca (50 nm)/Al (100 nm)] was successfully fabricated using solution processed. Inserting cured‐ FTV is between PEDOT:PSS and MEH‐PPV results in simultaneous reduction in hole injection from PEDOT:PSS to MEH‐PPV and blocking in electron transport from MEH‐PPV to anode. The maximum luminance and maximum current efficiency were enhanced from 1810 and 0.27 to 4640 cd/m² and 1.08 cd/A, respectively, after inserting cured‐ FTV layer. Current results demonstrate that the thermally cross‐linkable FTV enhances not only device efficiency but also film homogeneity after thermal curing. FTV is a promising electron‐ and hole‐blocking material applicable for the fabrication of multilayer PLEDs based on PPV derivatives. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 000: 000–000, 2012     

Characterization and electrical properties of polypyrrole/multiwalled carbon nanotube composites synthesized by in situ chemical oxidative polymerization

This study describes the preparation of polypyrrole (PPy)/multiwalled carbon nanotube (MWNT) composites by in situ chemical oxidative polymerization. Various ratios of MWNTs, which served as hard templates, were first dispersed in aqueous solutions with the surfactant cetyltrimethylammonium bromide to form micelle/MWNT templates and overcome the difficulty of MWNTs dispersing into insoluble solutions of pyrrole monomer, and PPy was then synthesized via in situ chemical oxidative polymerization on the surface of the templates. Raman spectroscopy, Fourier transform infrared (FTIR), field‐emission scanning electron microscopy (FESEM), and high‐resolution transmission electron microscopy (HRTEM) were used to characterize the structure and morphology of the fabricated composites. Structural analysis using FESEM and HRTEM showed that the PPy/MWNT composites were core (MWNT)–shell (PPy) tubular structures. Raman and FTIR spectra of the composites were almost identical to those of PPy, supporting the idea that MWNTs served as the core in the formation of a coaxial nanostructure for the composites. The conductivities of these PPy/MWNT composites were about 150% higher than those of PPy without MWNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1413–1418, 2006     

Thermoresponsive conductive polymer composite thin film and fiber mat: Crosslinked PEDOT:PSS and P(NIPAAm‐co‐NMA) composite

The thermoresponsive conductive composite (TCC) thin films and fiber mats, whose electrical property changed with temperature, were fabricated successfully. The thermocrosslinkable and thermoresponsive copolymer, poly(N‐isopropyl acrylamide‐co‐N‐methylolacrylamide) (PNN), was synthesized. The TCC thin film and fiber mat were fabricated by spin coating and electrospinning process of PEDOT:PSS/PNN solutions, respectively. After thermocrosslinking and doping by DMSO, the composite thin films and fiber mats were obtained. Fibrous structures of TCC fiber mats were observed by SEM. The surface resistance and conductivity of composites were measured. The thermoresponsivity and swelling ratio of TCCs were also studied. The thermoresponsive conductive property was analyzed by measuring the surface resistance of TCCs in water bath under various temperatures from 20 to 50 °C. With the increase of temperature, the TCCs shrank to be dense structure and showed lower surface resistance. The TCC fibers mat exhibited greater sensitivity to temperature than thin film owing to its fibrous structure. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1078–1087     

pH‐responsive polyphosphonates using butler's cyclopolymerization

The cationic monomer, N,N‐diallyl‐(diethylphosphonato)methylammonium chloride, and zwitterionic monomer, ethyl 3‐(N,N‐diallylammonio)methanephosphonate, were cyclopolymerized in aqueous solutions using ammonium persulfate or t‐butylhydroperoxide as initiators to afford a cationic polyelectrolyte (CPE) and a polyzwitterion ester (PZE), respectively. The CPE and PZE on acidic hydrolysis of the ester functionalities afforded the same polyzwitterionic acid (PZA): poly[3‐(N,N‐diallylammonio)methanephosphonic acid]. The solution properties of the CPE, pH‐responsive PZE, and PZA were studied in detail by potentiometric and viscometric techniques. Basicity constants of the phosphonate (P?O(OEt)O^?) and amine groups in the PZE and in the conjugate base of the PZE, respectively, were found to be “apparent” and as such follow the modified Henderson–Hasselbalch equation. In contrast to many polycarbobetaines and sulfobetaines, PZE was found to be soluble in salt‐free water as well as salt (including Ca²⁺, Li⁺)‐added solutions, and demonstrated “antipolyelectrolyte” solution behavior. The PZA, on the other hand, was found to be insoluble in salt‐free water, and on treatment with NaOH gave dianionic polyelectrolyte (DAPE) containing trivalent nitrogen and [P?O(O)₂^2?] groups. For the first time, several new phase diagrams of polyethylene glycol‐DAPE aqueous two‐phase systems (ATPSs) have been constructed in the presence of varying proportions of HCl. The ATPSs may find application in affinity partitioning of metal ions because DAPE is expected to be an effective chelator. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Polypyrrole stretchable actuators

Here, we report a simple way to prepare stretchable polypyrrole (PPy)‐based actuator materials that can be operated over a wide dynamic strain range and generate useable actuation displacements and pressures. The stretchable actuators were prepared as a laminated composite of PPy and a gold‐coated roughened rubber sheet. By manipulating the corrugated surface of the rubber substrate, the stretchability of PPy was greatly improved. Gold‐coated rubbers could be stretched to 30% without significant change in electrical resistance. The corrugated PPy/gold/rubber laminates successfully showed ～1% of actuation strain even when prestretched to 24%. The actuation strains were smaller than for similar free‐standing PPy films and a detailed analysis of the effects of corrugation and of the rubber substrate are presented to predict actuation strain under various prestretch strains. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Nanocomposite prepared from in situ grafting of polypyrrole to aminobenzoyl‐functionalized multiwalled carbon nanotube and its electrochemical properties

We reported the functionalization of multiwalled carbon nanotube (MWCNT) with 4‐aminobenzoic acid by a “direct” Friedel–Crafts acylation reaction in a mild polyphosphoric acid (PPA)/phosphorous pentoxide (P₂O₅) medium. The resulting 4‐aminobenzoyl‐functionalized MWCNT (AF‐MWCNT) was used as a platform for the grafting of polypyrrole (PPy) in ammonium persulfate (APS)/aqueous hydrochloric acid solution to produce PPy‐grafted MWCNT (PPy‐g‐MWCNT) composite. After dedoping with alkaline treatment, PPy‐g‐MWCNT displayed 20 times higher electrical conductivity than that of PPy. The current density and cycle stability of PPy‐g‐MWCNT composite were also remarkably improved compared with those of PPy homopolymer, suggesting that an efficient electron transfer between PPy and MWCNT was possible through covalent links. In addition, PPy‐g‐MWCNT displayed high electrocatalytic activity for oxygen reduction reaction (ORR). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Substituent effects on electrochemical and electrochromic properties of aromatic polyimides with 4‐(carbazol‐9‐yl)triphenylamine moieties

Three series of aromatic polyimides with 4‐(carbazol‐9‐yl)triphenylamine moieties were prepared from the polycondensation reactions of 4,4′‐diamino‐4″‐(carbazol‐9‐yl) triphenylamine (1), 4,4′‐diamino‐4″‐(3,6‐di‐tert‐butylcarbazol‐9‐yl)triphenylamine (t‐Bu‐1), and 4,4′‐diamino‐4″‐(3,6‐dimethoxycarbazol‐9‐yl)triphenylamine (MeO‐1), respectively, with various commercially available tetracarboxylic dianhydrides. In addition to high thermal stability and good film‐forming ability, the resulting polyimides exhibited an ambipolar electrochromic behavior. The polyimides based on t‐Bu‐1 and MeO‐1 revealed higher redox‐stability and enhanced electrochromic performance than the corresponding ones based on 1 because the active sites of their carbazole units are blocked with bulky t‐butyl or electron‐donating methoxy groups. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1172–1184     

A novel polymeric stabilizing system for modified lyocell solutions

A novel polymeric stabilizer consisting of iminodiacetic acid sodium salt (ISDB) and benzyl amine (BSDB) covalently bound to a styrene/divinyl benzene copolymer were studied. Calorimetric, spectroscopic, rheological, and high performance liquid chromatography analysis revealed distinctive improvements of the thermal stability of modified Lyocell solutions compared to the unstabilized solution and to that with conventional NaOH/propyl gallate stabilizer. Segregation processes of the system cellulose/N‐methylmorpholine‐N‐oxide and autocatalytic reactions caused by carboxyl group‐containing additives are suppressed by ISDB/BSDB. Concerning to surface‐active additives, enhanced thermal stability is only received for a weakly reactive charcoal. In the case of nanoscaled carbon black modifier, autocatalytic reactions indicated by isoperibolic measures are prevented by the new polymeric stabilizer system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1702–1713, 2006     

Mechanistic insight into initiation and chain transfer reaction of CO2/cyclohexene oxide copolymerization catalyzed by zinc?cobalt double metal cyanide complex catalysts

Although zinc? cobalt (III) double metal cyanide complex (Zn? Co (III) DMCC) catalyst is a highly active and selective catalyst for carbon dioxide (CO₂)/cyclohexene oxide (CHO) copolymerization, the structure of the resultant copolymer is poorly understood and the catalytic mechanism is still unclear. Combining the results of kinetic study and electrospray ionization‐mass spectrometry (ESI‐MS) spectra for CO₂/CHO copolymerization catalyzed by Zn? Co (III) DMCC catalyst, we disclosed that (1) the short ether units were mainly generated at the early stage of the copolymerization, and were hence in the “head” of the copolymer and (2) all resultant PCHCs presented two end hydroxyl (? OH) groups. One end ? OH group came from the initiation of zinc? hydroxide (Zn? OH) bond and the other end ? OH group was produced by the chain transfer reaction of propagating chain to H₂O (or free copolymer). Adding t‐BuOH (CHO: t‐BuOH = 2:1, v/v) to the reaction system led to the production of fully alternating PCHCs and new active site of Zn? Ot‐Bu, which was proved by the observation of PCHCs with one end ? Ot‐Bu (and ? OCOOt‐Bu) group from ESI‐MS and ¹³C NMR spectra. Moreover, Zn?OH bond in Zn? Co (III) DMCC catalyst was also characterized by the combined results from FT‐IR, TGA and elemental analysis. This work provided new evidences that CO₂/CHO copolymerization was initiated by metal? OH bond. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Flexible transparent fluorinated nanohybrid with innovative heat‐resistance property—new technology proposal for fabrication of transparent materials using “crystalline” polymer

A new technology for the production of transparent material, using a “crystalline” polymer, is proposed in this study. In addition, a heat‐resistant transparent flexible plastic film with a high hydrophobic surface and a thermal decomposition temperature near 400 °C was created. Partially fluorinated crystalline polymer with switchboard‐type lamellae results high transparency as a consequence of the formation of a high‐density amorphous structure based on high‐temperature drawing just below the melting point at 250 °C. Melt‐compounding with montmorillonite modified by the long‐chain quaternary phosphonium with high coverage induces formation of a nanohybrid that retains transparency and also results in an increase in the thermal degradation temperature by over 50 °C. Through this technology, which results in heat‐resistance, transparency, and flexibility, the nano‐micro‐millimeter structures of solid‐state polymers are hierarchically controlled, which enables the creation of new materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1674–1690     

Solid‐state 13C NMR study on thermal dehydration process of poly(methacrylic acid)(PMAA)

Thermal dehydration process of PMAA was investigated by solid‐state ¹³C NMR. For heat‐treated PMAA at 150°C, at which the dehydration goes very slowly, we observed three ¹³C peaks at 172, 178, and 187 ppm in the carboxyl group region. The peak at 172 ppm is due to the intramolecular cyclic anhydrides by comparing the reported value of ¹³C chemical shift. The peaks at 178 and 187 ppm were assigned to regularly aligned free carboxylic acids and intermolecular acid dimers, respectively, from the 2D‐exchange ¹³C NMR spectra, ¹³C chemical shift values and IR spectra. We concluded that by heat‐treatment the rearrangement of intermolecular hydrogen bonding of the carboxylic acids in PMAA occurs firstly to form the regularly aligned acid dimers, and the dimers dissociated to be the regularly aligned free carboxylic acids at high temperatures. The adjacent free carboxyl acids dehydrate with each other, resulting in the formation of intramolecular anhydrides. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2007–2012, 1999