Degradation of poly(butyl methacrylate) model compounds studied via high‐resolution electrospray ionization mass spectrometry

This study investigates the degradation behavior of poly(n‐butyl methacrylate) ( p(nBMA) ), poly(tert‐butyl methacrylate) ( p(tBMA) ), and poly(hexafluoro butyl methacrylate) ( p(HFBMA) ) on a molecular level under extreme environmental conditions. The polymers chosen are readily applicable in the formulation of surface coatings and were degraded under conditions which replicated the harsh Australian climate, in which surface coatings may reach temperatures of up to 95 °C and are exposed to broad‐spectrum UV radiation of up to 1 kW m^?2. The degradation profiles were mapped with high‐resolution electrospray ionization mass spectrometry (ESI‐MS) with a LCQ quadrupole ion trap mass analyzer, with the peak assignments confirmed to within 3 ppm using ESI‐MS with a LTQ‐Orbitrap mass detector. It was found that in all the butyl ester polymers analyzed herein—regardless of their tertiary side‐chain structure—the loss of the butyl ester group and subsequent formation of acid side groups are a component of the overall degradation pathway of poly(butyl methacrylate)s under these harsh conditions. However, it is also demonstrated that the magnitude of this pathway is intimately linked to the side‐chain structure with the propensity for degradation decreasing in the order p(tBMA) > p(nBMA) > p(HFBMA) . The degradation mechanisms identified in this study, in combination with the previous end‐group degradation studies of poly(methyl methacrylate) and poly(n‐butyl acrylate), have allowed a much deeper understanding of the molecular degradation behavior of poly(acrylate)s and poly(methacrylate)s in an extreme natural environment. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

The conformation of poly(3-dodecyl thiophene) within methacrylic polymer matrix

Blends of poly(3-dodecyl thiophene) (PDDT) with poly(methyl methacrylate), poly(butyl methacrylate) (PBMA), and poly(methyl methacrylate-co-butyl methacrylate) (PMMA/PBMA) were studied by polarization optical microscopy, atomic-force microscopy, and absorption spectroscopy and were modeled using molecular dynamics (MD) simulations. The observed thermochromic transitions are shown to be host-matrix dependent, with PDDT/PBMA absorption spectra differing substantially from pristine PDDT. The dispersion of PDDT within PBMA matrix is observed to be greater than in the other host polymers. MD calculations of both individual PDDT molecules and molecular aggregates suggest that the distribution of dihedral angles present in the PDDT backbone is the narrowest for aggregates of PDDT embedded within a polymer matrix. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2909–2917, 1999     

Fluorine‐containing linear block terpolymers: Synthesis and self‐assembly in solution

Linear triblock terpolymers of poly(n‐butyl methacrylate)‐b‐poly(methyl methacrylate)‐b‐poly(2‐fluoroethyl methacrylate) (PnBMA‐PMMA‐P2FEMA) were synthesized by sequential reversible addition fragmentation chain transfer (RAFT) polymerization. Kinetic studies of the homopolymerization of 2FEMA by RAFT polymerization demonstrated controllable characteristics with fairly narrow polydispersities (～1.30). The resultant PnBMA‐PMMA‐P2FEMA triblock terpolymers were characterized via ¹H NMR, ¹⁹F NMR, and gel permeation chromatography. These polymers formed micellar aggregates in a selective solvent mixture. The as‐formed micelles were analyzed using scanning electron microscopy and dynamic light scattering. It was found that these terpolymers could directly self‐organize into complex micelles in a tetrahydrofuran/methanol mixture with diameters that depended on polymer composition. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Heteroarm H‐shaped terpolymers through click reaction

Heteroarm H‐shaped terpolymers, (polystyrene)(poly(methyl methacrylate))‐ poly(tert‐butyl acrylate)‐(polystyrene)(poly(methyl methacrylate)), (PS)(PMMA)‐PtBA‐(PMMA)(PS), and, (PS)(PMMA)‐poly(ethylene glycol)(PEG)‐(PMMA)(PS), through click reaction strategy between PS‐PMMA copolymer (as side chains) with an alkyne functional group at the junction point and diazide end‐functionalized PtBA or PEG (as a main chain). PS‐PMMA with alkyne functional group was prepared by sequential living radical polymerizations such as the nitroxide mediated (NMP) and the metal mediated‐living radical polymerization (ATRP) routes. The obtained H‐shaped polymers were characterized by using ¹H‐NMR, GPC, DSC, and AFM measurements. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1055–1065, 2007     

Synthesis of PMMA‐b‐PBA block copolymer in homogeneous and miniemulsion systems by DPE controlled radical polymerization

In this research, poly(methyl methacrylate)‐b‐poly(butyl acrylate) (PMMA‐b‐PBA) block copolymers were prepared by 1,1‐diphenylethene (DPE) controlled radical polymerization in homogeneous and miniemulsion systems. First, monomer methyl methacrylate (MMA), initiator 2,2′‐azobisisobutyronitrile (AIBN) and a control agent DPE were bulk polymerized to form the DPE‐containing PMMA macroinitiator. Then the DPE‐containing PMMA was heated in the presence of a second monomer BA, the block copolymer was synthesized successfully. The effects of solvent and polymerization methods (homogeneous polymerization or miniemulsion polymerization) on the reaction rate, controlled living character, molecular weight (M_n) and molecular weight distribution (PDI) of polymers throughout the polymerization were studied and discussed. The results showed that, increasing the amounts of solvent reduced the reaction rate and viscosity of the polymerization system. It allowed more activation–deactivation cycles to occur at a given conversion thus better controlled living character and narrower molecular weight distribution of polymers were demonstrated throughout the polymerization. Furthermore, the polymerization carried out in miniemulsion system exhibited higher reaction rate and better controlled living character than those in homogeneous system. It was attributed to the compartmentalization of growing radicals and the enhanced deactivation reaction of DPE controlled radical polymerization in miniemulsified droplets. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4435–4445, 2009     

Separation of single‐walled carbon nanotubes with aromatic group functionalized polymethacrylates and building blocks contribution to the enrichment

We previously showed that in N,N‐dimethylformamide (DMF), poly(9‐anthracenylmethyl methacrylate) (PAMMA) and poly(2‐naphthylmethacrylate) selectively disperse semiconducting and metallic single‐walled carbon nanotubes (SWNTs), respectively. We have also proposed a new noncovalent polymer interaction based on photon induced dipole–dipole interaction to account for the metallicity‐based selectivity. In this article, we investigate two other polymethacrylates, that is, poly(benzyl methacrylate) (PBMA) and poly(methylmethacrylate)‐co‐(9‐anthracenylmethyl acrylate) (PMMA‐c‐PAMA) in the light of our previously proposed photon‐induced dipole–dipole interaction. We find that PBMA and PMM‐c‐PAMMA in DMF show no metallicity selectivity. The different selective behavior of the four polymers in DMF manifests the decisive influence of the side aromatic group in determining their metallicity selectivity. The nonpreferential energy transfer from PMMA‐c‐PAMA to SWNTs and the nonoverlap of PBMA fluorescence (in the ultraviolet range) with nanotube absorption account for their nonselectivity of specific nanotube species. Further, the parallel relationship between the diameters of extracted tube species and the affinity between polymers and solvents suggests the leading role of the polymeric conformation on the diameter selectivity. A sufficient (i.e., 2 weeks) standing time of the SWNTs solution after sonication, during which the polymers presumably optimize their conformation to the SWNTs, was found to be essential to the enrichment. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Characterization of the interaction energies for polystyrene blends with various methacrylate polymers

The binary interaction energies between styrene and various methacrylates were determined from newly examined phase boundaries with lattice–fluid theory. Because the blends of polystyrene (PS) and poly(cyclohexylmethacrylate) (PCHMA) were only miscible at high molecular weights when the blends were prepared by solution casting from tetrahydrofuran, we examined the miscibility of other blends by changing the molecular weights of PS or methacrylate polymers. On the basis of the phase‐separation temperature caused by the lower critical solution temperature, the miscibility of PS with the various methacrylates appeared to be in the order PCHMA > poly(n‐propyl‐methacrylate) (PnPMA) > poly(ethyl methacrylate) (PEMA) > poly(n‐butyl‐methacrylate) (PnBMA) > poly(iso‐butyl‐methacrylate) > poly(methyl methacrylate) (PMMA) > poly(tert‐butyl methacrylate), and the branching of butylmethacrylate appeared to decrease the miscibility with PS. The interaction energies between PS with various methacrylates obtained from phase boundaries with lattice–fluid theory reached minimum value corresponding to the styrene/n‐propylmethacrylate interaction. They were in the order PnPMA < PEMA < PCHMA < PnBMA < PMMA. The difference in the order of miscibility and interaction energies might be attributed to the terms related to the compressibility. The phase‐separation temperatures calculated with the interaction energies obtained here indicated that the PS/PEMA and PS/PnPMA blends at high molecular weights were miscible, whereas the PS/PnBMA blends were immiscible at high molecular weights. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2666–2677, 2000     

Diblock copolymers based on allyl methacrylate: Synthesis,characterization, and chemical modification

Different diblock copolymers constituted by one segment of a monomer supporting a reactive functional group, like allyl methacrylate (AMA), were synthesized by atom transfer radical polymerization (ATRP). Bromo‐terminated polymers, like polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(butyl acrylate) (PBA) were employed as macroinitiators to form the other blocks. Copolymerizations were carried out using copper chloride with N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as the catalyst system in benzonitrile solution at 70 °C. At the early stage, the ATRP copolymerizations yielded well‐defined linear block copolymers. However, with the polymerization progress a change in the macromolecular architecture takes place due to the secondary reactions caused by the allylic groups, passing to a branched and/or star‐shaped structure until finally yielding gel at monomer conversion around 40% or higher. The block copolymers were characterized by means of size exclusion chromatography (SEC), ¹H NMR spectroscopy, and differential scanning calorimetry (DSC). In addition, one of these copolymers, specifically P(BA‐b‐AMA), was satisfactorily modified through osmylation reaction to obtain the subsequent amphiphilic diblock copolymer of P(BA‐b‐DHPMA), where DHPMA is 2,3‐dihydroxypropyl methacrylate; demonstrating the feasibility of side‐chain modification of the functional obtained copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3538–3549, 2007     

Latices of poly(fluoroalkyl mathacrylate)‐b‐poly(butyl methacrylate) copolymers prepared via reversible addition–fragmentation chain transfer polymerization

Poly(fluoroalkyl mathacrylate)‐block‐poly(butyl methacrylate) diblock copolymer latices were synthesized by a two‐step process. In the first step, a homopolymer end‐capped with a dithiobenzoyl group [poly(fluoroalkyl mathacrylate) (PFAMA) or poly(butyl methacrylate) (PBMA)] was prepared in bulk via reversible addition–fragmentation chain transfer (RAFT) polymerization with 2‐cyanoprop‐2‐yl dithiobenzoate as a RAFT agent. In the second step, the homopolymer chain‐transfer agent (macro‐CTA) was dissolved in the second monomer, mixed with a water phase containing a surfactant, and then ultrasonicated to form a miniemulsion. Subsequently, the RAFT‐mediated miniemulsion polymerization of the second monomer (butyl methacrylate or fluoroalkyl mathacrylate) was carried out in the presence of the first block macro‐CTA. The influence of the polymerization sequence of the two kinds of monomers on the colloidal stability and molecular weight distribution was investigated. Gel permeation chromatography analyses and particle size results indicated that using the PFAMA macro‐CTA as the first block was better than using the PBMA RAFT agent with respect to the colloidal stability and the narrow molecular weight distribution of the F‐copolymer latices. The F‐copolymers were characterized with ¹H NMR, ¹⁹F NMR, and Fourier transform infrared spectroscopy. Comparing the contact angle of a water droplet on a thin film formed by the fluorinated copolymer with that of PBMA, we found that for the diblock copolymers containing a fluorinated block, the surface energy decreased greatly, and the hydrophobicity increased. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 471–484, 2007     

Quadruple click reactions for the synthesis of cysteine‐terminated linear multiblock copolymers

Synthesis of cysteine‐terminated linear polystyrene (PS)‐b‐poly(ε‐caprolactone) (PCL)‐b‐poly(methyl methacrylate) (PMMA)/or poly(tert‐butyl acrylate)(PtBA)‐b‐poly(ethylene glycol) (PEG) copolymers was carried out using sequential quadruple click reactions including thiol‐ene, copper‐catalyzed azide–alkyne cycloaddition (CuAAC), Diels–Alder, and nitroxide radical coupling (NRC) reactions. N‐acetyl‐L ‐cysteine methyl ester was first clicked with α‐allyl‐ω‐azide‐terminated PS via thiol‐ene reaction to create α‐cysteine‐ω‐azide‐terminated PS. Subsequent CuAAC reaction with PCL, followed by the introduction of the PMMA/or PtBA and PEG blocks via Diels–Alder and NRC, respectively, yielded final cysteine‐terminated multiblock copolymers. By ¹H NMR spectroscopy, the DP_ns of the blocks in the final multiblock copolymers were found to be close to those of the related polymer precursors, indicating that highly efficient click reactions occurred for polymer–polymer coupling. Successful quadruple click reactions were also confirmed by gel permeation chromatography. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of CO2‐switchable latexes using N‐[3‐(dimethylamino)propyl]‐methacrylamide (DMAPMAm)

CO₂‐switchable polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(butyl methacrylate) (PBMA) latexes were prepared via surfactant‐free emulsion polymerization (SFEP) under a CO₂ atmosphere, employing N‐[3‐(dimethylamino)propyl]methacrylamide (DMAPMAm) as a CO₂‐switchable, water‐soluble, and hydrolytically stable comonomer. The conversion of the SFEP of styrene reaches >95% in less than 5 h. The resulting latexes have near monodisperse particles (PDI ≤ 0.05), as confirmed by DLS and TEM. The latexes could be destabilized by bubbling nitrogen (N₂) and heating at 65 °C for 30 min, and easily redispersed by only bubbling CO₂ for a short time without using sonication. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1059–1066     

Degradation of poly(acrylates) under SF5+ primary ion bombardment studied using time‐of‐flight secondary ion mass spectrometry. 2. Poly(n‐alkyl methacrylates)

Polyatomic primary ions offer low penetration depth and high damage removal rates in some polymers, facilitating their use in the molecular depth profiling of these polymers by secondary ion mass spectrometry (SIMS). This study is the second in a series of systematic characterizations of the effect of polymer chemistry on degradation under polyatomic primary ion bombardment. In this study, time‐of‐flight SIMS (ToF‐SIMS) was used to measure the damage of ～90 nm thick spin‐cast poly(methyl methacrylate), poly(n‐butyl methacrylate), poly(n‐octyl methacrylate) and poly(n‐dodecyl methacrylate) films under extended (～2 × 10¹⁴ ions cm^?2) 5 keV SF₅⁺ bombardment. The degradation of the poly(n‐alkyl methacrylates) were compared to determine the effect of the length of the alkyl pendant group on their degradation under SF₅⁺ bombardment. The sputter rate and stability of the characteristic secondary ion intensities of these polymers decreased linearly with alkyl pendant group length, suggesting that lengthening the n‐alkyl pendant group resulted in increased loss of the alkyl pendant groups and intra‐ or intermolecular cross‐linking under SF₅⁺ bombardment. These results are partially at variance with the literature on the thermal degradation of these polymers, which suggested that these polymers degrade primarily via depolymerization with minimal intra‐ or intermolecular cross‐linking. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis of well‐defined cyclodextrin‐core star polymers

The synthesis of 21‐arm methyl methacrylate (MMA) and styrene star polymers is reported. The copper (I)‐mediated living radical polymerization of MMA was carried out with a cyclodextrin‐core‐based initiator with 21 independent discrete initiation sites: heptakis[2,3,6‐tri‐O‐(2‐bromo‐2‐methylpropionyl]‐β‐cyclodextrin. Living polymerization occurred, providing well‐defined 21‐arm star polymers with predicted molecular weights calculated from the initiator concentration and the consumed monomer as well as low polydispersities [e.g., poly(methyl methacrylate) (PMMA), number‐average molecular weight (M_n) = 55,700, polydispersity index (PDI) = 1.07; M_n = 118,000, PDI = 1.06; polystyrene, M_n = 37,100, PDI = 1.15]. Functional methacrylate monomers containing poly(ethylene glycol), a glucose residue, and a tert‐amine group in the side chain were also polymerized in a similar fashion, leading to hydrophilic star polymers, again with good control over the molecular weight and polydispersity (M_n = 15,000, PDI = 1.03; M_n = 36,500, PDI = 1.14; and M_n = 139,000, PDI = 1.09, respectively). When styrene was used as the monomer, it was difficult to obtain well‐defined polystyrene stars at high molecular weights. This was due to the increased occurrence of side reactions such as star–star coupling and thermal (spontaneous) polymerization; however, low‐polydispersity polymers were achieved at relatively low conversions. Furthermore, a star block copolymer consisting of PMMA and poly(butyl methacrylate) was successfully synthesized with a star PMMA as a macroinitiator (M_n = 104,000, PDI = 1.05). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2206–2214, 2001     

Bound fractions of methacrylate polymers adsorbed on silica using FTIR

The H‐bonding of carbonyl groups on a series of methacrylate polymers with silanols on fumed silica was studied with transmission FTIR. The set included poly(alkyl methacrylates) with alkyl groups, (n‐C_nH_2n+1) of n = 1, 2, 4, and 12 and poly(benzyl methacrylate). Shifts in the vibrational frequencies for bound carbonyl groups (of ～20 cm^?1 lower than those found in the bulk) were observed in the adsorbed polymer samples. A series of samples with different adsorbed amounts (varying from 0.5 to 2.0 mg m^?2) of each polymer was prepared to determine the effect of the side chain on the H‐bonding. The fractions of bound carbonyls, p, for each of the methacrylate polymers studied, were calculated from a model based on the ratios of the absorption coefficients of the bound to free carbonyl resonances, X (= α_b/α_f). The X values were determined from linear regressions of the ratios of the free to bound carbonyl intensities as a function of the amounts of adsorbed polymer, M_t. The bound fractions, p, were observed to decrease with increase in adsorbed amounts and with increase in the lengths of the side chains of the methacrylate polymers, except for poly(lauryl methacrylate) (PLMA). PLMA has a very low glass transition temperature (T_g) and is likely rubbery on the surface, whereas the other polymers are likely glassy at ambient temperature. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1911–1918, 2010     

ABC‐type hetero‐arm star terpolymers through “Click” chemistry

Hetero‐arm star ABC‐type terpolymers, poly(methyl methacrylate)‐polystyrene‐poly(tert‐butyl acrylate) (PMMA‐PS‐PtBA) and PMMA‐PS‐poly(ethylene glycol) (PEG), were prepared by using “Click” chemistry strategy. For this, first, PMMA‐b‐PS with alkyne functional group at the junction point was obtained from successive atom transfer radical polymerization (ATRP) and nitroxide‐mediated radical polymerization (NMP) routes. Furthermore, PtBA obtained from ATRP of tBA and commercially available monohydroxyl PEG were efficiently converted to the azide end‐functionalized polymers. As a second step, the alkyne and azide functional polymers were reacted to give the hetero‐arm star polymers in the presence of CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine ( PMDETA) in DMF at room temperature for 24 h. The hetero‐arm star polymers were characterized by ¹H NMR, GPC, and DSC. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5699–5707, 2006     

Synthesis of polymer with defined fluorescent end groups via reversible addition fragmentation transfer polymerization for characterizing the conformations of polymer chains in solutions

A new type of chain transfer agent used in reversible addition fragmentation chain transfer (RAFT) polymerization named 9‐anthracenylmethyl (4‐cyano‐4‐(N‐carbazylcarbodithioate) pentanoate) (ACCP) was synthesized with a total yield over 75% by the incorporation of both fluorescent donor and acceptor chromophores. Polymerization of heterotelechelic α,ω end‐labeled dye‐functionalized polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(n‐butyl methacrylate) (PBMA) with adjustable molecular weights and narrow polydispersity could be conducted by a one‐pot procedure through RAFT polymerization with this bischromophore chain transfer agent. The polymerizations demonstrated “living” controlled characteristics. By taking advantage of the characteristic fluorescence resonance energy transfer (FRET) response between the polymer chain terminals, the variation of chain dimensions in solution from the dilute region to the semidilute region can be monitored by changes in the ratio of the fluorescence intensities of the carbazolyl group to the anthryl group, which lends itself to potential applications in characterizing chain dimensions in solutions for thermodynamic or dynamic studies. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2413–2420     

Dendrimers as scaffolds for multifunctional reversible addition–fragmentation chain transfer agents: Syntheses and polymerization

The synthesis and characterization of novel first‐ and second‐generation true dendritic reversible addition–fragmentation chain transfer (RAFT) agents carrying 6 or 12 pendant 3‐benzylsulfanylthiocarbonylsulfanylpropionic acid RAFT end groups with Z‐group architecture based on 1,1,1‐hydroxyphenyl ethane and trimethylolpropane cores are described in detail. The multifunctional dendritic RAFT agents have been used to prepare star polymers of poly(butyl acrylate) (PBA) and polystyrene (PS) of narrow polydispersities (1.4 < polydispersity index < 1.1 for PBA and 1.5 < polydispersity index < 1.3 for PS) via bulk free‐radical polymerization at 60 °C. The novel dendrimer‐based multifunctional RAFT agents effect an efficient living polymerization process, as evidenced by the linear evolution of the number‐average molecular weight (M_n) with the monomer–polymer conversion, yielding star polymers with molecular weights of up to M_n = 160,000 g mol^?1 for PBA (based on a linear PBA calibration) and up to M_n = 70,000 g mol^?1 for PS (based on a linear PS calibration). A structural change in the chemical nature of the dendritic core (i.e., 1,1,1‐hydroxyphenyl ethane vs trimethylolpropane) has no influence on the observed molecular weight distributions. The star‐shaped structure of the generated polymers has been confirmed through the cleavage of the pendant arms off the core of the star‐shaped polymeric materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5877–5890, 2004     

Versatile ω‐end group functionalization of RAFT polymers using functional methane thiosulfonates

Five different polymers, poly[methyl methacrylate] (PMMA), poly[lauryl methacrylate] (PLMA), poly[diethylene glycol methacrylate] (PDEGMA), poly[N‐isopropylacrylamide] (PNIPA), and poly[styrene] (PS) prepared by the RAFT process and thus terminated with dithioesters were aminolyzed in the presence of S‐3‐butynyl methane thiosulfonate (MTS), which was synthesized in two steps. Analysis of the polymers by 2D NMR, UV–vis absorbance, and gel permeation chromatography revealed them to quantitatively carry acetylene end groups connected with disulfide bridges, indicating that functional MTS reagents can be employed for end group functionalization of RAFT polymers. This versatile method is of advantage compared with conjugations with functional maleimides, where isolation of terminal thiols is often required but inexpedient for poly[(meth)acrylates] because their terminal thiols may undergo backbiting and thus avoid conjugation. The acetylene‐terminated polymers were bound to an azide functionalized glass surface in a Cu(I) catalyzed cycloaddition. The modified surfaces exhibited water contact angles corresponding to the polarity of the attached polymers. In the case of the stimulus responsive polymers PNIPA and PDEGMA, the surfaces showed temperature‐dependent contact angles. The disulfide bond connecting the polymers to the surface could be selectively cleaved and resulted in all surfaces having the same contact angle, independent of the nature of the polymer prior attached to the surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3118–3130, 2009     

Synthesis of ω‐ and α,ω‐sulfonatotelechelics based on homopolymers and block copolymers of n‐butyl methacrylate and t‐butyl methacrylate

The synthesis of ω‐ and α,ω‐telechelics with sulfonate end groups through the sulfoalkylation of homopolymers and block copolymers of n‐butyl methacrylate and t‐butyl methacrylate with 1,3‐propane sultone is described. The polymerizations are initiated in tetrahydrofuran at −78 °C with either 1,1‐diphenyl‐3‐methylpentyllithium or dilithium 1,1,4,4‐tetraphenylbutane to obtain monofunctional or difunctional polymethacrylate anions, respectively. Narrow molecular weight distributions are obtained for the homopolymers and copolymers in the presence of LiCl in a 10/1 ratio relative to the initiator. The direct reaction of the poly(n‐butyl methacrylate) anions with the sultone results in low functionalization levels: f = 0.24–0.29 for the monofunctional anions and f = 0.32–0.35 for the difunctional anions. The reaction of the poly(t‐butyl methacrylate) anions or end‐capping of the poly(n‐butyl methacrylate) anions with t‐butyl methacrylate units before sulfoalkylation yields telechelics with f = 0.81–1.0 for the monofunctional anions and f = 1.74–1.94 for the difunctional anions. The telechelic polymers, purified by ultrafiltration, have been characterized by size exclusion chromatography, Fourier transform infrared, and ¹H NMR spectroscopy. The yield of the sulfoalkylation reactions, determined by colorimetric analysis of a complex formed with methylene blue, is in good agreement with the results obtained by nonaqueous titration of the acidified telechelics. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3711–3721, 2000     

Dynamic light scattering studies of atactic and syndiotactic poly(methyl methacrylate)s in dilute theta solution

The present article considers the coil‐to‐globule transition behavior of atactic and syndiotactic poly(methyl methacrylates), (PMMA) in their theta solvent, n‐butyl chloride (nBuCl). Changes in Rh in these polymers with temperature in dilute theta solutions were investigated by dynamic light scattering. The hydrodynamic size of atactic PMMA (a‐PMMA‐1) in nBuCl (M_w: 2.55 × 10⁶ g/mol) decreases to 61% of that in the unperturbed state at 13.0°C. Atactic PMMA (a‐PMMA‐2) with higher molecular weight (M_w: 3.3 × 10⁶ g/mol) shows higher contraction in the same theta solvent (α_η = R_h(T)/R_h (θ) = 0.44) at a lower temperature, 7.25°C. Although syndiotactic PMMA (s‐PMMA) has lower molecular weight than that of atactic samples (M_w: 1.2 × 10⁶), a comparable chain collapse was observed (α_η = 0.63) at 9.0°C. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2253–2260, 1999