Behavior of yeast cells in aqueous suspension affected by pulsed electric field

This work discusses pulsed electric fields (PEF) induced effects in treatment of aqueous suspensions of concentrated yeast cells (S. cerevisiae). The PEF treatment was done using pulses of near-rectangular shape, electric field strength was within E=2-5 kV/cm and the total time of treatment was t(PEF)=10(-4)-0.1 s. The concentration of aqueous yeast suspensions was in the interval of C(Y)=0-22 (wt%), where 1% concentration corresponds to the cellular density of 2x10(8) cells/mL. Triton X-100 was used for studying non-ionic surfactant additive effects. The electric current peak value I was measured during each pulse application, and from these data the electrical conductivity sigma was estimated. The PEF-induced damage results in increase of sigma with t(PEF) increasing and attains its saturation level sigma approximately sigma(max) at long time of PEF treatment. The value of sigma(max) reflects the efficiency of damage. The reduced efficiency of damage at suspension volume concentration higher than phi(Y) approximately 32 vol% is explained by the percolation phenomenon in the randomly packed suspension of near-spherical cells. The higher cytoplasmic ions leakage was observed in presence of surfactant. Experiments were carried out in the static and continuous flow treatment chambers in order to reveal the effects of mixing in PEF-treatment efficiency. A noticeable aggregation of the yeast cells was observed in the static flow chamber during the PEF treatment, while aggregation was not so pronounced in the continuous flow chamber. The nature of the enhanced aggregation under the PEF treatment was revealed by the zeta-potential measurements: these data demonstrate different zeta-potential signs for alive and dead cells. The effect of the electric field strength on the PEF-induced extraction of the intracellular components of S. cerevisiae is discussed.     

The effect of aggregation on the electrical conductivity of spin-coated polymer/carbon nanotube composite films

This paper considers the feasibility of replacing indium tin oxide (ITO) with spin-coated, polymer-based composite films that are filled with multiwalled carbon nanotubes (MWNTs). The coating mixture consists of a solvent with low volatility, a dissolved thermoplastic polymer, and MWNTs. The high aspect ratio of MWNTs and their good electrical conductivity enable electrical percolation at very low concentrations, so that films can be prepared that conduct electricity while retaining good optical transparency. Although the MWNTs are driven to aggregate by Van der Waals interactions, the high viscosity of the polymer/solvent solution enables the preparation of metastable, homogeneous dispersions. However, exposing the mixtures to shear leads to aggregation, the magnitude of which depends on the duration of the shear. This effect could be observed directly in spin-coated films using both optical microscopy and conductivity measurements, with aggregation causing a drop in conductivity at high nanotube loading, and more complex non-monotonic behavior at concentrations approaching the percolation threshold.     

Effect of surfactant structure on the stability of carbon nanotubes in aqueous solution

The suspending behaviors of multiple-wall carbon nanotubes (MWNTs), including pristine MWNTs (p-MWNTs) and acid-mixture-treated MWNTs (MWNTCOOH), stabilized by cationic single-chain surfactant, dodecyltrimethylammonium bromide (DTAB), and cationic gemini surfactant hexyl-alpha,beta-bis(dodecyldimethylammonium bromide) (C 12C 6C 12Br 2) were studied systematically. The surfactant structure influences the suspendability of MWNTs dramatically as well as the surfactant adsorption behavior on the nanotubes. Although both the surfactants can disperse the MWNTs effectively, they actually show different stabilizing ability. DTAB is not capable of stabilizing these two MWNTs below critical micelle concentration (CMC). However, C 12C 6C 12Br 2 can suspend both the nanotubes effectively even well below its CMC. Moreover, the adsorption of these two surfactants reaches equilibrium at twice the CMC with the original MWNT concentration of 2 mg/mL, 2 mM for C 12C 6C 12Br 2, and 30 mM for DTAB. After the adsorption equilibrium, the maximum amounts of the two suspended MWNTs in C 12C 6C 12Br 2 solution are about twice as much as those in DTAB solution. The strong hydrophobic interaction among the C 12C 6C 12Br 2 molecules and between the C 12C 6C 12Br 2 molecules and the nanotubes as well as the high charge capacity of C 12C 6C 12Br 2 lead to its much stronger adsorption ability on the MWNTs and result in its superior stabilizing ability for the MWNTs in aqueous phase. The gemini surfactant provides a possibility to effectively stabilize the MWNTs in aqueous solutions even at very low surfactant concentration well below its CMC.     

Wormlike micelles in poly(oxyethylene) surfactant solution: Growth control through hydrophilic-group size variation

Rheological responses of colloidal gels formed from fumed silica suspensions in aqueous KOH solution at pH 11 by the addition of cationic surfactants, such as dodecyltrimethylammonium chloride (C12 TAC) and hexadodecyltrimethylammonium chloride (C16 TAC) have been investigated as functions of silica and surfactant concentrations. Stable and aggregated fumed silica suspensions with negative charges cause gelling by adding the cationic surfactants through electrical neutralization of their micelles. The resulting critical strain and storage modulus of the gelled silica suspension increase with an increase in the surfactant concentration, irrespective of the cationic surfactant. This means that the higher the surfactant concentration is, the more effective the electrical neutralization interaction through the micelle of the cationic surfactant is. Moreover, the resulting gels can be classified into the strong-link gel and the weak-link one in the presence of C12 TAC and C16 TAC, respectively, from a comparison of the silica volume fraction dependences of critical strain and storage modulus with the fractal gel model.     

Laponite assisted dispersion of carbon nanotubes in water

The ability of Laponite to stabilize aqueous suspensions of multiwalled carbon nanotubes (MWCNTs) was investigated with the help of analytical centrifugation, microscopic image analysis, and measurements of electrical conductivity of hybrid Laponite+MWCNT suspensions. The impact of nanotube concentration C(n) (0.0025-0.5 wt%) and Laponite/MWCNTs ratio X (varied within 0-1 wt/wt) on the properties of Laponite+MWCNT hybrid suspensions was discussed. It was observed that sonication of MWCNTs at critical minimal concentration of Laponite X(c)≈0.25±0.05 resulted in efficient dispersion and formation of stabilized suspensions of individual nanotubes. The stabilization of nanotubes in the presence of Laponite was explained by adsorption of Laponite particles and formation of a hydrophilic charged shell on the surface of nanotubes. Increase of MWCNT concentration above the critical value resulted in percolation and formation of spatially extended electrically conductive networks of particles.     

Kinetics of Simultaneous Adsorption of Poly(vinylpyrrolidone) and Sodium Dodecyl Sulfate on Alumina Particles

The effect of Cibacron Blue 3GA (CB) and bovine serum albumin (BSA) as guest molecules on the microstructure of reversed micelles has been investigated with electrical conductivity measurements. CB as an affinity ligand was directly introduced to reversed micelles formed with a cationic surfactant, cetyltrimethylammonium bromide. The anionic CB has electrostatic interactions with the cationic surfactant and also has a strong binding affinity to BSA. The conductivity of reversed micellar systems increases gradually with the increase of temperature either with or without the addition of CB. The conductivity of reversed micellar systems increases with the addition of tributyl phosphate to the organic phase. No electrical percolation appears with an increase of temperature or water concentration. The conductivity of reversed micellar systems decreases with the addition of CB and decreases further with the addition of both CB and BSA. The conductivity of the organic phase is 3 orders of magnitude lower than that of the aqueous phase under the same CB concentration, which indicates that CB is probably confined to the closed microdomains of reversed micellar systems. The conductivity behavior of reversed micelles has not shown much difference with the methods used for the addition of CB either by the injection method or by phase transfer. Copyright 2000 Academic Press.     

The influence of ionic and nonionic surfactants on aggregative stability and electrical surface properties of aqueous suspensions of titanium dioxide

The influence of concentration of nonionic TRITON X-100 and anionic ATLAS G-3300 surfactants, and pH of medium on the size and zeta-potential of TiO2 particles in the water suspensions has been studied. Suspensions have been prepared by mixing of the titanium dioxide in the suitable mediums at 10 min and 6 h correspondingly. It was established, that the duration of mixing of the suspensions has an essential influence on the dependence of zeta-potential and size of particles versus concentration of surfactant. However, the duration of mixing does not influence the dependence of electrical conductivity and pH of the suspensions on concentration of surfactant. It is shown that anionic ATLAS G-3300 surfactant is more effective stabilizator of aqueous suspensions of titanium dioxide, than nonionic surfactants of TRITON X-100. It is found that hydrophobic interaction has important role in the processes of stabilization of suspensions for nonionic surfactant, and for anionic surfactant--moving of psi(delta)-planes into solution's depth.     

Synthesis and aggregation behavior of a hexameric quaternary ammonium surfactant

A star-shaped hexameric quaternary ammonium surfactant (PAHB), bearing six hydrophobic chains and six charged hydrophilic headgroups connected by an amide-type spacer group, was synthesized. The self-assembly behavior of the surfactant in aqueous solution was studied by surface tension, electrical conductivity, isothermal titration microcalorimetry, dynamic light scattering, cryogenic transmission electron microscopy, and NMR techniques. The results reveal that there are two critical aggregate concentrations during the process of aggregation, namely C(1) and C(2). The aggregate transitions are proved to be caused by the changes of the surfactant configuration through hydrophobic interaction among the hydrocarbon chains. Below C(1), PAHB may present a star-shaped molecular configuration due to intramolecular electrostatic repulsion among the charged headgroups, and large aggregates with network-like structure are observed. Between C(1) and C(2), the hydrophobic interaction among the hydrophobic chains may become stronger to make the hydrophobic chains of the PAHB molecules curve back and pack more closely, and then the network-like aggregates transfer to large spherical aggregates of ～100 nm. Beyond C(2), the hydrophobic interaction may become strong enough to cause the PAHB molecular configuration to turn into a pyramid-like shape, resulting in the transition of the spherical large aggregates to spherical micelles of ～10 nm. Interestingly, the PAHB displays high emulsification ability to linear fatty alkyls even at very low concentration.     

Effects of surfactants and pH of medium on zeta potential and aggregation stability of titanium dioxide suspensions

The effects of benzethonium chloride, sodium dodecylbenzenesulfonate, and 4-(1,1,3,3-(tetramethylbutyl)phenyl poly(ethylene glycol) on the zeta potential and aggregation stability of aqueous rutile-form titanium dioxide suspensions are studied in the pH range of 2–12. It is shown that the nonionic surfactant does not affect significantly the zeta potential and aggregation stability of the suspensions. The influence of ionic surfactants on the aggregation stability of the suspensions considerably depends on the pH of a medium. At pH values above the isoelectric point of titanium dioxide suspensions (pH₀ = 6.2), the suspensions demonstrate a high aggregation stability in the presence of the anionic surfactant, sodium dodecylbenzene-sulfonate (irrespective of its content), while, at pH < pH₀, the aggregation stability of the suspensions markedly increases with the surfactant concentration. In the presence of the cationic surfactant, benzethonium chloride, the aggregation stability of the suspensions is independent of the surfactant concentration at pH < pH₀, whereas, at pH > pH₀, it increases with the surfactant concentration.     

Adsorption behavior of oxyethylated surfactants at the air/water interface

The low-shear viscosity eta(0) of colloidal suspensions of acrylic latex or silica in aqueous gelatin has been measured at a temperature above the sol-gel transition. Measurements were made on dilution of a concentrated suspension with water or a gelatin solution. Thus, either the gelatin : colloid ratio was maintained or it was varied at constant aqueous gelatin concentration. Systems were studied with four lime-processed gelatins of different molecular weights at two concentrations of added salt. In addition, the latex particle size and the thickness of the adsorbed gelatin layer were measured by photon correlation spectroscopy (PCS) under dilute conditions. The dependence of the low-shear viscosity eta(0) on particle concentration was exponential and did not follow the well-established Krieger-Dougherty model for simple hard-sphere suspensions over the concentration range studied. A simple phenomenological model, eta(0)=eta(o)10(phi(e)/phi(s)), was found to predict the behavior well. Here, eta(o) is the viscosity of a gelatin solution of the corresponding solution concentration, phi(e) is proportional to the volume fraction of the particles, and phi(s) is a scaling factor, which was determined to have a value of 0.85. With this value of phi(s), the dimensions determined from PCS could be used to predict the viscosity values.     

Characterization of micelle formation of dodecyldimethyl-N-2-phenoxyethylammonium bromide in aqueous solution

Aggregation behavior of dodecyldimethyl-N-2-phenoxyethylammonium bromide commonly called domiphen bromide (DB) was studied in aqueous solution. The Krafft temperature of the surfactant was measured. The surfactant has been shown to form micellar structures in a wide concentration range. The critical micelle concentration was determined by surface tension, conductivity, and fluorescence methods. The conductivity data were also employed to determine the degree of surfactant counterion dissociation. The changes in Gibb's free energy, enthalpy, and entropy of the micellization process were determined at different temperature. The steady-state fluorescence quenching measurements with pyrene and N-phenyl-1-naphthylamine as fluorescence probes were performed to obtain micellar aggregation number. The results were compared with those of dodecyltrimethylammonium bromide (DTAB) surfactant. The micelle formation is energetically more favored in DB compared to that in DTAB. The 1H-NMR spectra were used to show that the 2-phenoxyethyl group, which folds back onto the micellar surface facilitates aggregate formation in DB.     

Surfactant--polymer aggregates formed by sodium dodecyl sulfate, poly(N-vinyl-2-pyrrolidone), and poly(ethylene glycol)

The interaction of sodium dodecyl sulfate (SDS) in aqueous solution with poly(N-vinyl-2-pyrrolidone) (M(w) = 55,000 g/mol) in the presence of poly(ethylene glycol) (M(w) = 8000 g/mol) is investigated by electrical conductivity, zeta potential measurements, viscosity measurements, fluorescence spectroscopy, and small-angle X-ray scattering (SAXS). The results indicate that SDS-polymer interaction occurs at low surfactant concentration, and its critical aggregation concentration is fairly dependent on polymer composition. The polymer-supported micelles have average aggregation numbers dependent on surfactant concentration, are highly dissociated when compared with aqueous SDS micelles, and have zeta potentials that increase linearly with the fraction of PVP at constant SDS concentration. The analysis of the SAXS measurements indicated that the PVP/PEG/SDS system forms surface-charged aggregates of a cylindrical shape with an anisometry (length to cross-section dimension ratio) of about 3.0.     

Electrical Properties Investigation in PA12/PANI Composites

Summary: Volume conducting PA-12 based composites powders were chemically prepared by in situ polymerization and aniline doping at room temperature. These kinds of polyamide / PANI composites were investigated regarding their electrical properties. Their ac and dc electrical properties measured in the frequency range of 10⁻²–10⁷ Hz are reported and the frequency dependence of electrical conductivity was investigated as a function of PANI concentration leading to the determination of the conductivity. The experimental conductivity was found to increase continuously with PANI content and explained by percolation theory with a relatively low percolation threshold of about 0.4 wt.%. The dielectric behavior of various PANI polymer composites has been characterized by the critical frequency ω_c (denoting the crossover from the dc plateau of the conductivity to its frequency dependent ac behaviour). Modelling the conductivity behavior versus volume fraction using Slupkowski approach has revealed that the considered parameters are not sufficient to describe the electrical conductivity behavior.     

Micelle formation by N-alkyl-N-methylpyrrolidinium bromide in aqueous solution

The micellization of the ionic liquid N-alkyl-N-methylpyrrolidinium bromide (C(n)MPB, n = 12, 14 and 16) in aqueous solutions was investigated by surface tension measurements, electrical conductivity and static luminescence quenching. The effectiveness of the surface tension reduction (Π(cmc)), maximum surface excess concentration (Γ(max)) and the minimum area (A(min)) occupied per surfactant molecule at the air/water interface can be obtained from the surface tension measurements at 25 °C. The critical micelle concentration (cmc) at different temperatures and a series of thermodynamic parameters (ΔG, ΔH and ΔS) of micellization were evaluated from electrical conductivity measurements in the temperature range of 25-45 °C. The thermodynamic parameters show that the micelle formation is entropy-driven at low temperature and enthalpy-driven at high temperature. Furthermore, the micelle aggregation number (N(agg)) of C(n)MPB was calculated according to the Turro-Yekta method through static luminescence quenching and found that N(agg) (49, 55, and 59) increased with the hydrophobic chain length of C(n)MPB.     

Aggregation behavior of single-walled carbon nanotubes in dilute aqueous suspension

The aggregation behavior of colloidal single-walled carbon nanotubes (SWNT) in dilute aqueous suspensions was investigated using a novel light scattering measurement technique. The aggregation of SWNT in three suspensions was examined: (1) nanotubes after acid treatment; (2) as-received nanotubes stabilized by a nonionic surfactant; and (3) acid-treated nanotubes with nonionic surfactant. Continuous light scattering measurements of the SWNT suspensions (probing the 38-436 nm length scale) made over two weeks showed that the nanotubes in each sample formed networks with fractal-like structures. The as-received nanotubes were stable over the measurement period, while the acid-treated nanotube suspension showed greater dispersion variability over time, yielding looser structures at large length scales and more compact structures at smaller length scales. The addition of surfactant to the acid-treated suspension significantly enhanced nanotube dispersion.     

Synthesis and micellar properties of 1-decyl-2,3-dimethylimidazolium bromide surfactant in water and water-ethanolamine mixtures at 298.15 K

1-Decyl-2,3-dimethylimidazolium bromide (ddmimBr) has been synthesized by the reaction of 1,2-dimethylimidazole and 1-bromodecane. Micellization of ddmimBr surfactant in water (W) and water-ethanolamine (W-EA) with the weight percent of EA changing within the range 0-39.79%, has been investigated at 298.15 K. Information about the influence of the added EA on the critical micelle concentration (CMC) was obtained through density and surface tension measurements. This last provides information about the dependence of the surface excess concentration, the minimum area per surfactant molecule and the surface pressure at the CMC on the added weight percentage of organic solvent. The effect of binary aqueous mixtures of W-EA on the apparent molar volume (phi V) of the ddmimBr has been investigated. The apparent molar volume upon aggregation (Delta phi V) shows a maximum at about 15 wt% of EA, this behavior is discussed in terms of the changes of the solvent structure. Partial specific volume data, obtained by density measurements, indicate that the fraction of solvent molecules interact with the surfactant remained roughly constant.     

Ammonium ionic liquid as modulator of the critical micelle concentration of ammonium surfactant at aqueous solution: conductimetric and dynamic light scattering (DLS) studies

We report measurements of self aggregation in aqueous solution of an ionic liquid (IL), didecyl-dimethylammonium nitrate ([DDA][NO(3)]) and a surfactant hexadecyl-trimethylammonium bromide (CTAB) and of mixtures of these two salts. The electrical conductivity and dynamic light scattering (DLS) measurements were used for the characterization of the aggregation process. The conductivity measurements were performed at three temperatures. The critical micelle concentration (CMC) was determined at different temperatures and at different ratio of two salts. The effect of IL on the micellization of CTAB has been discussed. Our results suggest that organized structures formed by CTAB and [DDA][NO(3)] self assembly in domains of several hundred nanometers size. The micellar solubility of the salicylic acid in mixed salt aqueous solutions was determined to probe the physical properties of these assemblies. We have observed, that the micellar solubility enhancement was only slightly influenced by the nature of micelles present in aqueous solution. This proves that salicylic acid solubilization is enthalpy driven.     

Interaction between the water soluble poly{1,4-phenylene-[9,9-bis(4-phenoxy butylsulfonate)]fluorene-2,7-diyl} copolymer and ionic surfactants followed by spectroscopic and conductivity measurements

The interaction has been studied in aqueous solutions between a negatively charged conjugated polyelectrolyte poly{1,4-phenylene-[9,9-bis(4-phenoxybutylsulfonate)]fluorene-2,7-diyl} copolymer (PBS-PFP) and several cationic tetraalkylammonium surfactants with different structures (alkyl chain length, counterion, or double alkyl chain), with tetramethylammonium cations and with the anionic surfactant sodium dodecyl sulfate (SDS) by electronic absorption and emission spectroscopy and by conductivity measurements. The results are compared with those previously obtained on the interaction of the same polymer with the nonionic surfactant C12E5. The nature of the electrostatic or hydrophobic polymer-surfactant interactions leads to very different behavior. The polymer induces the aggregation with the cationic surfactants at concentrations well below the critical micelle concentration, while this is inhibited with the anionic SDS, as demonstrated from conductivity measurements. The interaction with cationic surfactants only shows a small dependence on alkyl chain length or counterion and is suggested to be dominated by electrostatic interactions. In contrast to previous studies with the nonionic C12E5, both the cationic and the anionic surfactants quench the PBS-PFP emission intensity, leading also to a decrease in the polymer emission lifetime. However, the interaction with these cationic surfactants leads to the appearance of a new emission band (approximately 525 nm), which may be due to energy hopping to defect sites due to the increase of PBS-PFP interchain interaction favored by charge neutralization of the anionic polymer by cationic surfactant and by hydrophobic interactions involving the surfactant alkyl chains, since the same green band is not observed by adding either tetramethylammonium hydroxide or chloride. This effect suggests that the cationic surfactants are changing the nature of PBS-PFP aggregates. The nature of the polymer and surfactant interactions can, thus, be used to control the spectroscopic and conductivity properties of the polymer, which may have implications in its applications.     

Enhanced separation of Compound Xueshuantong capsule using functionalized carbon nanotubes with cationic surfactant solutions in MEEKC

A novel additive of multi‐walled carbon nanotubes (MWNTs) dispersed with cationic surfactants or mixed cationic/anionic surfactants was used for MEEKC separation of eight phenolic compounds, four glycosides, and one phenanthraquinone. In this context, several parameters affecting MEEKC separation were studied, including the dispersion agents of MWNTs, MWNTs content, oil type, SDS concentration, and the type and concentration of cosurfactant. Compared with conventional MEEKC, the addition of all types of MWNTs dispersions using single or mixed cationic surfactant solutions in running buffers was especially useful for improving the separation of solutes tested, as they influenced the partitioning between the oil droplets and aqueous phase due to the exceptional electrical properties and large surface areas of MWNTs. Use of cationic surfactant‐coated MWNTs (6.4 μg/mL) as the additive in a microemulsion buffer (0.5% octanol, 2.8% SDS, 5.8% isopropanol, and 5 mM borate buffer) yielded complete resolution of 13 analytes. The proposed method has been successfully applied for the detection and quantification of the studied compounds in a complex matrix sample (Compound Xueshuantong capsule).     

Conductometric and Gravimetric Studies of the Kinetics of Graphite Sedimentation in Aqueous Dispersions

The kinetics of graphite sedimentation in aqueous dispersions is studied using conductometric and gravimetric techniques. Triton X-305, a nonionic surfactant, is used to regulate the aggregation of hydrophobic graphite particles and to stabilize the system. The differences in the kinetics of the change in the weight and conductivity of sediments depending on the surfactant concentration are discussed. It is shown that insulating films of low conductivity are formed around particles at a concentration corresponding to coating of graphite particles with a monolayer of the surfactant and the conductivity of the sediments sharply decreases. At a higher surfactant concentration, which corresponds to the critical micellization concentration, compact sediments are formed; their conductivity first decreases and then increases in the process of restructuring. The change in the sediment structure as a function of the surfactant concentration is discussed.