石墨烯修饰玻碳电极伏安法测定酪氨酸

制备了石墨烯修饰玻碳电极,研究了酪氨酸在修饰电极上的电化学行为.优化了包括支持电解质、溶液pH、修饰剂用量、富集电位及时间等测定条件.在0.1 mol·L-1pH 7.0的磷酸盐缓冲溶液中,峰电流与酪氨酸的浓度在3×10-6～1.2×10-4mol·L-1的范围内呈良好的线性关系,检出限为2 × 10-7 mol·L-...     

聚苯胺-石墨烯修饰玻碳电极同时测定邻苯二酚和对苯二酚

本文制备了聚苯胺-石墨烯修饰玻碳电极,并用循环伏安(CV)法和微分脉冲伏安(DPV)法研究了邻苯二酚(CC)和对苯二酚(HQ)在该修饰电极上的电化学行为。实验结果表明,相对于裸玻碳电极,HQ和CC在聚苯胺-石墨烯修饰电极上的氧化峰电流显著提高,氧化峰电位相差104.8mV,实现了CC和HQ的选择性测定。DPV法同时测定二酚时,HQ和CC分别在1.0×10-6~8.0×10-4 mol/L浓度范围内与其峰电流呈良好的线性关系,相关系数R分别为0.998、0.997,检出限(S/N=3)分别为1.0×10-7、8.0×10-8mol/L。将该方法用于模拟水样分析,回收率为95.3%~103.5%。     

氧化石墨烯/铁氰化铈修饰玻碳电极同时测定扑热息痛和咖啡因

采用滴涂法和电沉积法制备了氧化石墨烯/铁氰化铈(CeFe(CN)6)纳米复合膜修饰玻碳电极。用扫描电镜对氧化石墨烯和氧化石墨烯/CeFe(CN)6纳米复合膜进行了表征。分别用循环伏安法和差分脉冲伏安法研究了扑热息痛和咖啡因在修饰电极上的电化学行为。结果表明,在0.1 mol/L醋酸盐缓冲溶液(pH5.0)中,扑热息痛和咖啡因在此修饰电极上具有良好的电化学行为,扑热息痛和咖啡因分别在1.0×10-7～6.0×10-5mol/L和1.0×10-6～1.3×10-4mol/L浓度范围内与电化学响应信号呈良好的线性关系,相关系数分别为0.990和0.992;信噪比为3时,扑热息痛和咖啡因检出限分别为5.0×10-8mol/L和5.2×10-7mol/L。将本方法用于人尿样品分析,回收率为96.1%～105.4%。     

百草枯在氧化石墨烯修饰玻碳电极上的电化学行为及其差分脉冲伏安测定

将氧化石墨烯悬浮液(1g·L~(-1))10μL滴涂于玻碳电极表面,烘干后,在0.10mol·L~(-1)的KH_2PO_4溶液中于-0.9V还原600s制备了氧化石墨烯修饰玻碳电极,用扫描电子显微镜、透射电子显微镜和电化学方法对修饰电极进行了表征。用差分脉冲伏安法研究了百草枯在氧化石墨烯修饰电极上的电化学行为,发现此修饰电极对百草枯的还原有明显的电催化作用。百草枯在pH 7.5的磷酸盐缓冲溶液中,在氧化石墨烯修饰电极上产生催化还原反应,在差分脉冲伏安曲线上先后在-0.6,-0.1V处出现2个还原峰。因后者与底液的还原峰重叠,故测定中采用-0.6V处的还原峰电流为测量值。经试验,百草枯在修饰电极上的富集电位为-0.6V,富集时间为200s,选用的扫描速率为50 mV·s~(-1)。在最佳试验条件下百草枯浓度在9.00×10~(-7)～1.00×10~(-5) mol·L~(-1)和1.00×10~(-5)～5.00×10~(-5) mol·L~(-1)内与其在-0.6V处的还原峰电流呈线性关系,检出限(3s/k)为1.64×10~(-7) mol·L~(-1)。方法应用于农药中百草枯含量的测定,测定值与标示值相符,对土壤样品进行加标回收试验,回收率在89.5%～114%之间。     

纳米铂修饰玻碳电极对邻苯二酚的电化学氧化及测定

应用循环伏安法研究了邻苯二酚在纳米铂修饰玻碳(PtNPs/GC)电极上的电化学氧化行为。实验表明,PtNPs/GC电极对邻苯二酚有很强的电催化作用,其伏安扫描氧化峰电流随着温度的升高而增大,但氧化峰电位略有负移。常温下,邻苯二酚能自发在电极表面发生聚合反应,生成具有导电性的聚合膜,其催化氧化电流与邻苯二酚浓度在1.0×10-6mol/L~5.0×10-5mol/L范围内呈良好的线性关系,检出限为2.9×10-7mol/L。     

TiO2-石墨烯-Nafion复合膜修饰玻碳电极同时测定多巴胺和尿酸

利用在玻碳电极上修饰了TiO2-石墨烯-Nafion复合膜制得的修饰电极进行多巴胺(DA)和尿酸(UA)的同时测定。用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了该修饰电极的电化学行为。在pH为7.0的磷酸盐缓冲液(PBS)中,修饰电极对于DA和UA的电化学氧化具有良好的电催化性能。DA和UA的氧化峰电流分别在2～120和60～300μmol/L浓度范围内呈良好的线性关系,检出限分别为0.066和0.102μmol/L。实验结果表明,TiO2-石墨烯-Nafion复合膜修饰电极显著提高了检测的灵敏度,并表现出良好的选择性和重现性。     

石墨烯/铁氰化钴复合膜修饰玻碳电极同时测定对苯二酚、邻苯二酚和间苯二酚

采用滴涂法和电沉积法制备了石墨烯/铁氰化钴复合膜修饰玻碳电极. 用扫描电镜对该纳米复合膜进行了表征.用循环伏安法研究了对苯二酚(HQ)、邻苯二酚(CT)和间苯二酚(RS)在修饰电极上的电化学行为. 实验结果表明, 相对于裸玻碳电极和石墨烯修饰电极, HQ, CT 和RS 在石墨烯/铁氰化钴修饰电极上的氧化峰电流显著提高. 利用差分脉冲伏安法测定, HQ, CT 和RS 分别在1.0×10^－6～1.5×10^－4 mol/L, 1.0×10^－6～2.0×10^－4 mol/L 和3.5×10^－6～2.5×10^－4 mol/L浓度范围内与氧化峰电流呈良好的线性关系, 相关系数分别为0.991, 0.993 和0.992. 信噪比为3 时, HQ, CT 和RS 检出限分别为2.0×10^－7, 2.1×10^－7 和3.5×10^－7 mol/L. 将该方法用于水样分析, 回收率为95.6%～106.1%.     

聚苏木精修饰玻碳电极测定酪氨酸

通过在玻碳电极上电聚合聚苏木精的方法制备了聚苏木精修饰电极,研究了酪氨酸在修饰电极上的电化学行为。在0.1 mol/L磷酸盐缓冲溶液(pH3.0)中,富集电位为-0.3 V,富集时间为180 s,氧化峰电流与酪氨酸的浓度在5.0×10-6～1.0×10-4mol/L的范围内呈良好的线性关系,检出限为3.0×10-7mo...     

苏丹红Ⅰ在壳聚糖-氧化石墨烯自组装膜修饰玻碳电极上的电化学行为及其测定

制备了壳聚糖-氧化石墨烯自组装膜修饰玻碳电极(CS-GO/GC),并用电化学阻抗法进行表征,研究了苏丹红Ⅰ在该修饰电极上的电化学行为。实验结果表明,苏丹红Ⅰ在该修饰电极上出现了1个氧化峰,为不可逆电化学反应。在50～250 mV.s-1扫速范围内,氧化峰电流与扫速呈线性关系,该电极过程受吸附控制,苏丹红Ⅰ在修饰电极上的电子转移数和质子数均为1,扩散系数为1.70×10-6cm2.s-1。采用差分脉冲伏安法对苏丹红Ⅰ进行测定,结果表明,苏丹红Ⅰ浓度与其氧化峰电流在6.0×10-8～5.0×10-6mol/L范围内呈良好的线性关系,相关系数为0.995,检出限为4.45×10-8mol/L。该修饰电极具有良好的重现性和稳定性,可简便、快捷、灵敏地检测咸鸭蛋黄中苏丹红Ⅰ的含量。     

银掺杂聚L-甲硫氨酸修饰电极同时测定对苯二酚和邻苯二酚

用循环伏安法制备了银掺杂聚L-甲硫氨酸修饰玻碳电极,研究了对苯二酚和邻苯二酚在该修饰电极上的电化学行为,建立了同时测定对苯二酚和邻苯二酚的新方法.研究发现,在pH=5.0的磷酸盐缓冲溶液中,扫速为100 mV/s时,对苯二酚和邻苯二酚在银掺杂聚L-甲硫氨酸修饰玻碳电极上均出现1对氧化还原峰,峰电位分别为:Epa=0.228 V、Epc =0.162 V和Epa=0.347 V、Epc =0.287 V,二者的氧化峰电位差达119 mV,还原峰差达125 mV.在最佳的条件下,用差分脉冲伏安法同时测定邻苯二酚和对苯二酚的线性范围为3.00 ×10-6～1.00 ×10-4mol/L,检出限为8.0×10-7 mol/L(对苯二酚)和5.0×10-7 mol/L(邻苯二酚).此法用于废水样中对苯二酚和邻苯二酚的测定,获得满意结果.     

Polyfurfural-Electrochemically Reduced Graphene Oxide Modified Glassy Carbon Electrode for the Direct Determination of Nitrofurazone

An electrochemical sensor based on a polyfurfural-electrochemically reduced graphene oxide modified glassy carbon electrode has been developed for the sensitive and rapid determination of nitrofurazone. The morphologies and properties of the sensor were characterized by electrochemical impedance spectroscopy, scanning electron microscopy, cyclic voltammetry, and differential pulse voltammetry (DPV). In pH 7.0 Britton–Robinson buffer solution, the as-prepared polyfurfural-electrochemically reduced graphene oxide modified glassy carbon electrode shows excellent electrocatalytic performance for the electrochemical reduction of nitrofurazone, and the reduction peak current is about 9.45, 1.31, and 1.25 times higher than that of the bare glassy carbon electrode, polyfurfural modified glassy carbon electrode, and electrochemically reduced graphene oxide modified glassy carbon electrode, respectively. The DPV determination of nitrofurazone indicates that the linear range and detection limit of nitrofurazone are 1–50 and 0.25?µmol/dm³, respectively. In addition, this sensor exhibits high selectivity, reproducibility, stability, and also was successfully used to directly determine nitrofurazone in the commercial antibacterial lotion with comparative sensitivity to high-performance liquid chromatography, showing its promising application prospects.     

Electrochemical Detection of Alloxan on Reduced Graphene Oxide Modified Glassy Carbon Electrode

Alloxan is a toxic reagent that strongly induces the diabetes by destroying insulin‐producing β‐cells in the pancreas of living organisms. The reduction product of alloxan is dialuric acid, which is responsible for the intracellular generation of ROS to enhance the stress in living cells to cause kidney disease or diabetic nephropathy. Herein, we studied for the first time the electrochemical properties of alloxan on reduced graphene oxide modified glassy carbon electrode (rGO/GCE) in 0.1 M phosphate buffer solution (PBS) at pH 7. The obtained results were compared with graphene oxide modified GCE (GO/GCE) and bare GCE surfaces. The modified rGO/GCE showed well defined redox couple with 10 fold increase in both reduction as well as oxidation peak current for alloxan than that of GO/GCE and bare GCE. Differential pulse voltammetry (DPV) technique shows the linear increase in both oxidation and reduction peak current of alloxan in the range of 30 μM to 3 mM with LOD of 1.2 μM. An amperometric signal of alloxan is also increases with respect to each addition of 50 μM of alloxan on rGO/GCE at constant potential of ?0.05 V. The linear range of alloxan is observed between 50 μM to 750 μM (S/N=3). This kind of rGO/GCE surface is more suitable platform or sensor matrix for estimating unknown concentration of alloxan molecule in the real biological systems.     

聚对氨基苯磺酸/石墨烯修饰玻碳电极伏安法测定痕量汞

制备了对氨基苯磺酸/石墨烯复合膜修饰电极,研究了汞在修饰电极上的电化学行为。 在0.1 mol/L、pH=4.0的磷酸盐缓冲液中,以此修饰电极为工作电极,在-1.2 V搅拌富集5 min,用差分脉冲伏安法测定0.31 V处的溶出峰电流。 结果表明,该电极显著提高了汞离子的电化学响应信号。 在优化条件下,峰电流与Hg2+的浓度在1.0×10-6~5.0×10-4 mol/L范围内呈良好的线性关系,相关系数为0.995。 方法的检出限为5.0×10-7 mol/L。 将该法用于水样中痕量汞的测定,回收率为92.2%~105.2%。     

Electrochemical Determination of Dopamine Using a Poly(3,4-Ethylenedioxythiophene)-Reduced Graphene Oxide-Modified Glassy Carbon Electrode

Poly(3,4-ethylenedioxythiophene) was deposited on a reduced graphene oxide-decorated glassy carbon electrode through an electrochemical polymerization. The resulting glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene) electrode was applied as an electrochemical biosensor for the determination of dopamine in the presence of ascorbic acid and uric acid. The material deposited on glassy carbon electrode was investigated in terms of morphology and structural analysis. The comparison of electrochemical behavior of the glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene) electrode with the glassy carbon electrode-graphene oxide, glassy carbon electrode-reduced graphene oxide, and glassy carbon electrode-poly(3,4-ethylenedioxythiophene) electrodes exhibited high electrocatalytic activity for dopamine detection. Electrochemical kinetic parameters of glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene), including the charge transfer coefficient α (0.49) and electron transfer rate constant k_s (1.04), were determined and discussed. The glassy carbon electrode-reduced graphene oxide-poly(3,4-ethylenedioxythiophene) electrode was studied for the determination of dopamine by differential pulse voltammetry and exhibited a linear range from 19.6 to 122.8?µM with a sensitivity of 3.27?µA?µM^?1?cm^?2 and a detection limit of 1.92?µM. The developed biosensor exhibited good selectivity toward dopamine with high reproducibility and stability.     

茶碱在石墨烯/磷钨酸修饰电极上的电化学行为及测定

采用滴涂法制备了石墨烯/磷钨酸修饰电极(GO-PTA/GCE),运用循环伏安法研究了茶碱(THEO)在该修饰电极上的电化学行为,并讨论了修饰剂石墨烯和磷钨酸的配比及用量、底液种类及浓度、扫速对其测定的影响。运用交流阻抗法研究修饰前后电极表面的特性。结果表明,在0.02 mol/L H2SO4溶液中,THEO在该修饰电极上于1.185 V出现一不可逆氧化峰,且在100~800 mV/s范围内,其峰电流与扫速平方根(v1/2)呈线性关系,表明该电极过程为受扩散控制的不可逆过程。THEO在该修饰电极上的电子转移数n=1,有效面积A=0.116 9 cm2,扩散系数D=6.675×10-5cm2/s。在优化实验条件下,采用差分脉冲伏安法对THEO进行定量测定,发现THEO的峰电流与其浓度在6.0×10-7~1.0×10-4mol/L范围内呈良好的线性关系,检出限可达5.5×10-7mol/L。采用该法对水样中THEO进行检测,回收率为92.6%~106.3%。     

Elecrochemical Determination of Ethanol by a Palladium Modified Graphene Nanocomposite Glassy Carbon Electrode

Pristine palladium nanoparticles were decorated on graphene nanosheets for the development of a low-cost, nonenzymatic ethanol sensor. The nanocomposite was characterized by ultraviolet–visible absorbance spectroscopy, infrared spectroscopy, and field emission scanning electron microscopy equipped with energy dispersive X-ray spectroscopy. Cyclic voltammetry and chronoamperometry were used to quantify ethanol in alkaline media. A graphene palladium nanocomposite-modified glassy carbon electrode provided a detection limit of 2?mM with a linear dynamic range of 2–210?mM for ethanol determination. The nanocomposite exhibited excellent stability for 100 cyclic voltammetry scans. Ethanol oxidation was performed across a range of temperatures, unlike enzymatic based sensors. Moreover, the catalytic material showed a low activation energy and low onset potentials for the oxidation of ethanol. Interference studies with congeners of ethanol in fermentation chambers showed good selectivity for the analyte. The enhanced catalytic activity for ethanol detection involves the combination of pristine palladium nanoparticles with the enhanced conductivity of graphene.     

多巴胺在电沉积石墨烯修饰碳分子线电极上的电化学测定

以分子线二苯乙炔为修饰剂和粘合剂制备了一种新型的碳糊电极-碳分子线电极(CMWE),并以其为基底电极采用电化学还原法将石墨烯(GR)沉积到CMWE表面得到电沉积石墨烯修饰碳分子线电极(GR/CMWE)。考察了多巴胺(DA)在该修饰电极上的电化学行为。实验结果显示DA在GR/CMWE上出现了1对峰形良好的氧化还原峰,与裸电极相比,该氧化还原峰的电流增大,峰电位差减小,表明修饰电极对DA的电化学反应有催化作用。在最佳实验条件下峰电流与DA浓度在8.0×10-7~2.0×10-3mol/L范围内呈良好的线性关系,检出限(3σ)为2.55×10-7mol/L。将该电极用于多巴胺注射液样品的检测,结果满意。     

邻苯二酚和对苯二酚在钴氢氧化物膜修饰玻碳电极上的选择性测定

通过镀膜/循环伏安法制备了钴氢氧化物膜修饰的玻碳电极。该修饰电极对邻苯二酚(CA)和对苯二酚(HQ)具有较强的电催化活性。考察了支持电解质酸度对邻苯二酚和对苯二酚电化学响应的影响,选用0.1 mol/LPBS(pH 10.0)作为支持电解质。利用差示脉冲伏安法(DPV)对邻苯二酚和对苯二酚进行选择性检测,当两者浓度同时改变时,邻苯二酚和对苯二酚在6～100μmol/L范围内氧化峰电流与其浓度呈良好的线性关系,检出限分别为2×10–7,5×10–7mol/L(S/N=3)。钴氢氧化物膜电极具有较好的稳定性、重现性及较强的抗干扰能力,将此修饰电极应用于模拟水样中邻苯二酚和对苯二酚的测定,回收率为95.4%～100.4%。