Influence of fluctuations on thermal conductivity of high-Tc YBa2Cu3O7−δ superconductor

To study a behavior of the thermal conductivity near T_c specific heat and thermal diffusivity of the YBa₂Cu₃O_7−δ high-T_c ceramics were simultaneously measured. Close to T_c = 92.30 K the thermal diffusivity and the thermal conductivity discovered minima and the specific heat – maximum. Quantitative analysis of the influence of thermodynamical fluctuations showed the same power laws with Gaussian exponent equal to 0.5 and existing of crossover from the 3D Gaussian to 3D XY critical behavior in the specific heat and thermal conductivity at the approach to T_c. To explain the minimum in thermal conductivity at T_c we propose a mechanism of scattering of phonons on the superconducting fluctuations.     

Temperature dependence of the critical current in YBa2Cu3O7−δ and Bi2Sr2Ca1Cu2O8 Josephson junctions

We have studied the stationary Josephson effect on YBa₂Cu₃O_7−δ (T_c=90 K) and Bi₂Sr₂Ca₁Cu₂ O₈ (T_c=80 K and 87 K for two samples of different origin) ceramic based junctions. The temperature dependence of the critical current near T_c has been found as I_c≈(T_c-T) for the Y-Ba-Cu-O samples indicating that they should be classified as S-N-I-N-S type junctions. The I-V curves of the Bi-Sr-Ca-Cu samples show the typical behaviour of S-I-S structures. Using Ambegaokar-Baratoff's theory for Bi₂Sr₂Ca₁Cu₂O₈, the temperature dependence of the superconducting state gap Δ(T) was calculated and it was evaluated that 1.452Δ(0)/k_BT_c3.5.     

Temperature dependence of the exafs spectrum in YBa2Cu3O7−δ compounds

The temperature dependence of the extended X-ray absorption fine structure (EXAFS) is studied in the high T_c superconductors, YBa₂Cu₃O_7−δ. The measurements were done at the Cu K-edge for samples of two orthorhombic phases (T_c≈90 K and ≈58 K, respectively) and a nonsuperconducting tetragonal phase. Interatomic distances and mean square relative displacements σ² for Cu-O bonds are determined by the least squares refinement. The results indicate that values of σ² increase near T_c for both the orthorhombic samples. It is concluded that this anomalous behavior related to T_c is caused by an anomalous vibration of oxygen atoms in the Ba-O layer. Changes in the Cu-O distances from 300 to 20 K are not found.     

Realization and properties of ramp-type YBa2Cu3O7−δ/Au/Nb junctions

All-thin-film ramp type Josephson junctions between YBa₂Cu₃O_7−δ and Nb have been fabricated. This procedure allows connections between high-T_c and low-T_c superconductors at different crystal sides of the high-T_c superconductor on one chip, which is of great interest for novel phase devices. A thin Au layer is incorporated as a chemical barrier to avoid oxygen transfer from the YBa₂Cu₃O_7−δ to the Nb. Critical current densities up to 600 A/cm² are obtained at T=4.2 K, with typical R_nA values of 0.8 μΩ cm². The variation of the magnetic field dependence of the critical current with the angle between the junction barrier and the YBa₂Cu₃O_7−δ crystal axes is explained by considering a predominant d_x²−y² order parameter symmetry of the YBa₂Cu₃O_7−δ. The successful fabrication of these junctions allows the implementation of novel superconducting electronics, such as complementary Josephson circuitry or proposed qubit concepts, using the unconventional order parameter symmetry of the high-T_c superconductor.     

Electrical transport and superconductivity in the Al2O3-Bi2Sr1.8Ca1.2Cu2Oy and MgO-Bi2Sr1.8Ca1.2Cu2Oy composites

We have measured the resistivities of Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites with the nominal Bi₂Sr_1.8Ca_1.2Cu₂O_y volume fraction, ₂₂₁₂, ranging from 0.15 to 1.00. For the Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu ₂O_y composites, we find for the samples with ₂₂₁₂≥0.6 that the superconducting transition temperature, T_c, is not disturbed by the addition of Al₂O₃. For ₂₂₁₂<0.3, no zero-resistivity state is observed. For the MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites, T_c is barely disturbed for the samples with ρ₂₂₁₂≥0.7. No superconducting state is observed for the samples with ρ₂₂₁₂<0.35. The variation of (300 K) with ρ₂₂₁₂ indicates a three-dimensional percolating Bi-Sr-Ca-Cu-O matrix occurring at ρ₂₂₁₂≈0.19 and ≈0.15 in Al₂O₃-Bi₂Sr_1.8Ca_1.2 Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y, respectively. Both resistivity and magnetization measurements suggest that the reactions of Bi₂Sr_1.8Ca_1.2Cu₂O_y with MgO are weaker than with Al₂O₃.     

Microwave absorption and paracoherence excess conductivity studies in high-Tc superconductors

Single phase polycrystalline samples of La_1.8Sr_0.2CuO₄, YBa₂Cu₃O_7−δ and Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_y high-T_c superconductors have been studied using XRD, SEM, EDAX, (T), χ_AC and EPR techniques. Detailed investigations on low-field-dependent microwave absorption have been carried out in order to investigate the effects of field exposure, field cooling, zero field cooling and amplitude of field variation on the samples. The results have been discussed on the basis of granular model via Josephson junctions of high-T_c superconductors. Over and above, paracoherence excess conductivity analysis has been carried out in all the three samples. The critical exponent (γ) estimated for all the three samples in close vicinity to their respective transition temperatures has an excellent agreement with the theoretically predicted value for 3-dimensional XY-ferromagnet (γ = 1.33 for D = 3, N = 2).     

Surface atomic imaging of La2CuO4 and superconducting Tl2Ba2Ca2Cu3O10

Surface structures of the high T_c oxide superconductors Tl₂Ba₂Ca₂Cu₃O₁₀ and La₂CuO₄ have been studied by high resolution electron microscopy. In addition to the single atomic layer of La on the (113) surface observed previously, several atomic layers of the C-form of La₂O₃ were found to coat the (001) surfaces of La₂CuO₄. Surface reconstruction with the incorporation of excess Ba on the (110) surface of Tl₂Ba₂Ca₂Cu₃O₁₀ has been observed together with a stepped (11l) surface produced by a combination of the (110) and (001) planes. The (001) surface of Tl₂Ba₂Ca₂Cu₃O₁₀ was also found to terminate with a Ba-O layer. Possible mechanisms for the formation of these surface structures are discussed.     

Origin of intrinsic Josephson coupling in the cuprates and its relation to order parameter symmetry: An incoherent hopping model

Experiments on the cuprate superconductors demonstrate that these materials may be viewed as a stack of Josephson junctions along the direction normal to the CuO₂ planes (the c-axis). In this paper, we present a model which describes this intrinsic Josephson coupling in terms of incherent quasiparticle hopping along the c-axis arising from wave-function overlap, impurity-assisted hopping, and boson-assised hopping. We use this model to compute the magnitude and temperature T dependence of the resulting Josephson critical current j_c(T) for s- and d-wave superconductors. Contrary to other approaches, d-wave pairing in this model is compatible with an intrinsic Josephson effect at all hole concentrations and leads to j_c(T) T at low T. By parameterizing our theory with c-axis resistivity data from YBa₂Cu₃O_7−δ (YBCO), we estimate j_c(T) for optimally doped and underdoped members of this family. j_c(T) can be measured either directly or indirectly through microwave penetration depth experiments, and current measurements on Bi₂Sr₂CaCu₂O₈ and La_2−xSr_xCuO₄ are found to be consistent with s-wave pairing and the dominance of assisted hopping processes. The situation in YBCO is still unclear, but our estimates suggest that further experiments on this compound would be of great help in elucidating the validity of our model in general and the pairing symmetry in particular.     

Oxyanion derivatives of cuprate superconductors superconducting 123 phosphates

While YSr₂Cu₃O₇ cannot be prepared under ambient conditions, partial substitution of the phosphate group for copper, as in YSr₂Cu_2.8(PO₄)_0.2O_y, stabilizes this phase in the orthorhombic structure, but the material is not superconducting. Superconductivity in YSr₂Cu_2.8(PO₄)_0.2O_y is obtained by increasing the hole concentration through partial substitution of Y by Ca, as in Y_0.7Ca_0.3Sr₂Cu_2.8(PO₄)_0.2O_y (T_c≈40 K). By incorporating the phosphate group in orthorhombic YBaSrCu₃O ₇, a stable tetragonal derivative of the formula YBaSrCu_2.8(PO₄)_0.2O_y (T_c≈ 47 K) has been prepared; the T_c increases to 70 K by partial substitution of Y by Ca as in Y_0.7Ca_0.3BaSrCu_2.8(PO₄)_0.2O_y.     

Trapping mechanism of superconductivity suppression induced by Pr substitution in the Ho1−xPrxBa2Cu3O7−δ system

Pr concentration dependence of the superconducting transition temperature T_c in the Ho_1−xPr_xBa₂Cu₃O_7−δ system is determined from measurements of DC electrical resistance. This dependence coincides with that for the parallely studied Y_1−xPr_xBa₂Cu₃O_7−δ reference system. Both systems have the same value of the critical concentration x_c=0.58, in accordance with nearly equal ionic radii of Ho³⁺ and Y³⁺ ions. It has been shown that the T_c(x) curve can be described with a single mechanism based on a decreasing number of sheet holes trapped by Pr^IV-ions, if one takes also into account that the number of these ions changes with x.     

Thermal transport in the oxygenated magnetic superconductor, Eu1.5Ce0.5RuSr2Cu2O10+δ

The thermal conductivity and thermopower are reported for a hole doped Eu_1.5Ce_0.5RuSr₂Cu₂O_10+δ sample that has been annealed at 1100 K under an oxygen pressure of 54 atm. At T_c=45 K superconductivity and weak ferromagnetism coexist (T_m=180 K). Weak features in the thermopower, S(T), and thermal conductivity, κ(T), are observed both at T_m and at T^*=140 K. The thermopower begins to decrease sharply toward zero at T_c, and there is an extremely sharp increase of about 30% in the thermal conductivity at T_c. This “first order” transition may be related to the sudden appearance of a spontaneous vortex phase at T_c. A small shoulder is observed in κ(T) in the temperature range T=5–13 K.     

Systematic thermopower measurements of the thallium cuprates Tl(Ba,Sr)2Cam−1CumO2m+3−δ and Tl2Ba2Cam−1CumO2m+4+δ

The thermoelectric power (TEP) S versus temperature has been systematically investigated for several series of the superconducting cuprates Tl(Ba,Sr)₂Ca_m−1Cu_mO_2m+3−δ (m = 2, 3) and Tl₂Ba₂Ca_m−1Cu_mO_2m+4+δ (m = 1, 2, 3). The consideration of the S(T_c) curves allows two important points to be found evidence for. The first one deals with the fact that all these superconducting thallium cuprates are systematically overdoped whatever T_c, and whatever the number of Cu or Tl layers; no underdoped superconducting cuprate could be obtained. The second point shows that there exist two classes of Tl cuprates: the weakly overdoped cuprates that exhibit a T_{c max} ≥ 100 K (all the triple copper layer cuprates and the 2212 cuprates) and those which can be heavily doped that exhibit a T_{c max} ≤ 90 K (the 2201 and the 1212 cuprates). The different behavior of thallium cuprates compared to YBa₂Cu₃O_7−δ and to bismuth cuprates is discussed.     

Intergranular properties of YBCO and BSCCO ceramic superconductors at low fields

Isothermal low-field AC susceptibility measurements have been used to analyze the intergranular critical current density J_c(T) on sintered, non-oriented YBa₂Cu₃O_7−δ and Bi₂Sr₂CaCu₂O_8+δ ceramic samples at zero field. Below the critical temperature, potential variations, J_c(T) ≈ (1−t_j)^m with t_j = T/T_j, have been found, T_j being the onset of grain's coherence, but with different exponents, supporting that different mechanisms limit the intergranular J_c values. Moreover, the effect of texture has been also considered on Bi₂Sr₂CaCu₂O_8+δ ceramics grown by the laser floating zone method, which have stronger intergranular junctions. Their high-temperature behaviour is limited by intrinsic effects, while at low temperatures the quality of the junctions is the limiting factor. The temperature dependence of the χ′(h₀) extrapolation at zero filed has also been correlated with the evolution of the intergranular penetration depth, λ_J(T).     

Study of the magnetic properties of single-crystal Ba0.6K0.4BiO3

The magnetic properties of single-crystal Ba_0.6K_0.4BiO₃ were studied. The results show that this isotropic superconductor (cubic structure with T_c ≈ 32 K) exhibits irreversibility and relaxation properties similar to those observed in the layered, high temperature superconductors. For fields above 0.1 T, an irreversibility line B_irr = B_irr (0) (1 − t)ⁿ with n = 3/2 and B_irr (0) = 20 T is observed. The comparison among several superconducting systems with different anisotropies suggests that the irreversibility line is unlikely to be the melting line for the YBa₂Cu₃O_7−δ.     

Electrical transport properties of dense bulk YBa2Cu4O8 produced by hot isostatic pressing

Highly dense sintered YBa₂Cu₄O₈ has been produced by hot isostatic pressing (HIP). The electrical resistivity of this material has been measured as a function of temperature T and pressure in the range 40–650 K and 0–0.7 GPa. Both the temperature dependence and the pressure dependence of are found to be well described by a model based on the standard Bloch-Grüneisen theory. It is pointed out that is liner in T only under isobaric conditions, while is strongly nonlinear in all high-T_c superconductors under isochoric (constant volume) conditions. The critical current density of the material is 900 A/cm² at 4 K, while the resistivity is 630 μΩ cm at 294 K.     

High critical current density YBa2Cu3O7−δ tapes prepared by the surface-oxidation epitaxy method

YBa₂Cu₃O_7−δ (YBCO) films with high critical current density (J_c) were successfully fabricated on nickel tapes buffered with epitaxial NiO. NiO was prepared on the textured nickel tape by the surface-oxidation epitaxy (SOE) method. We have reported so far a critical temperature (T_c) of 87 K and J_c=4–6×10⁴ A/cm² (77 K, 0 T) for the YBCO films on NiO/Ni tapes. To enhance the superconducting properties of the YBCO films on the SOE-grown NiO, depositions of thin oxide cap layers such as YSZ, CeO₂, and MgO on NiO were investigated. These oxide cap layers were epitaxially grown on NiO and provided the template for the epitaxial growth of YBCO films. Substantially improved data of T_c=88 K and J_c=3×10⁵ A/cm² (77 K, 0 T) and 1×10⁴ A/cm² (77 K, Hc, 4 T) were obtained for YBCO film on NiO, by using a MgO cap layer with a thickness of 50 nm. The method described in this paper is a simple way to produce long YBCO tape conductors with high-J_c values.     

Phase diagrams of YBa2Cu4O8 and YBa2Cu3.5O7.5 in the pressure range 1 bar≤PO2≤3000 bar

The P-T-x phase diagram of the pseudobinary system (Y-Ba-Cu-O)-O₂ has been further investigated in the oxygen pressure range between 1 and 3000 bar. The stability ranges of the phases YBa₂Cu₄O₈ (124), YBa₂Cu_3.5O_7.5−x (123.5) and YBa₂Cu₃O_7−x (123) have been determined. Long duration experiments showed that the 123 phase is not stable at least down to 7 bar≤P≤20 bar oxygen and 900°C. It is not clear whether at lower pressures and temperatures the 123 phase is thermodynamically stable or metastable due to low reaction rates. In the presence of excess CuO, the 124 is the stable phase. The melting of 124 pellets at P_O2=2800 bar shows that even at this pressure the 124 compound melts incongruently. Using the phase diagram data we could change the T_c of 123.5 from 16 to 70 K by varying systematically the nonstoichiometry. Due to a narrow homogeneity range the T_c of 124 remained constant but is different for powder pellets (81 K) and for crystals (70 K), probably due to the influence of the flux. Single crystals of both 124 and 123.5 with dimensions up to 4 mm were grown from the flux under high oxygen pressure.     

Magnetization study of polycrystalline YBa2AlxCu(3−x)O7−δ (x = 0.05, 0.10 and 0.20) compounds

Superconductivity in polycrystalline YBa₂Al_xCu_(3−x)O_7−δ materials was characterized by dynamic AC and quasistatic DC magnetometry. Intragranular persistent current density and low-loss intergranular critical current density were deduced using DC and AC techniques, respectively. Addition of aluminum produced modest increases in the intragranular persistent current for x < 0.2, but drastically reduced the intergranular critical current density for x = 0.2. The critical temperature T_c for superconductivity decreased only 4% for Al content up to x = 0.2.     

Hole distribution and madelung energy in the high-Tc oxide superconductors

Evidence is presented that in high-T_c superconductors the electrostatic interaction as expressed by the Madelung energy is the key factor in determining the charge distribution and in particular the distribution of the holes between the CuO₂-planes and other structural subunits. Specifically, this explains the phase diagram (T_c as a function of oxygen content and oxidizing power) of cation-substituted YBa₂Cu₃O_6+y and the oxygen ordering in YBa₂Cu₃O_6.5. Moreover, we argue that the dependence of T_c on strontium content in La_2−xSr_xCuO₄ is similarly due to the fact that holes go into the (La,Sr)O-sheets as well as into the CuO₂-planes.     

Superconductivity, Ca content and oxygen deficiency of Ga(Sr,Ca)2(Yb,Ca)Cu2O7

Superconducting transition temperature (T_c), Ca content and oxygen deficiency are studied on GaSr_1.8Ca_0.2Yb_1−xCa_xCu₂O₇ (x≤0.35). Superconducting samples with T_c=52 K are prepared after the annealing at 20 MPa of oxygen. The T_c is reduced through a slight oxygen loss accompanied by annealing in air above 650°C. The oxygen loss suggests the presence of short Cu–O chains in the GaO₄ slab. The formal valence of planar Cu required for the appearance of superconductivity depends on oxygen and Ca contents. The critical formal Cu valences are 2.105 and 2.125 for the samples annealed in air at 600°C and at 835°C, respectively. The values are higher than those of usual high-T_c superconductors. This can be explained by a high concentration of localized holes in the CuO₅ slab.