Microstructure and Defect Characterization of Nanostructured Ni<Subscript>3</Subscript>Al

Summary.  Nanostructured Ni₃Al was produced by the inert gas condensation and in situ compaction technique and characterized by means of high-resolution transmission electron microscopy (HRTEM), X-ray diffraction, and density measurements. The defect structure was investigated using positron annihilation lifetime spectroscopy (PALS). It is shown that in some samples besides the cubic also the martensitic phase can be present. The defect structure can be divided into three major components: vacancy-like defects in the grain boundaries and nano-voids with a size of 1 nm as seen with PALS, and large pores with sizes up to 8 nm as seen with HRTEM. Furthermore, it is shown that an increasing compaction temperature leads to significantly smaller nano-voids. Received October 5, 2001. Accepted (revised) November 12, 2001     

Electrochemical study of spinel oxide systems with nominal compositions Ni1− x Cu x Co2O4 and NiCo2− y Cu y O4

Studies on the electrochemical behaviour of Ni_{1− x} Cu _x Co₂O₄ (x ≤ 0.75) and NiCo_{2− y} Cu _y O₄ (y ≤ 0.30) electrodes in 5 mol dm⁻³ KOH aqueous solutions are presented. The oxide layers have been prepared by thermal decomposition of aqueous nitrate solutions on nickel supports at 623 K. Powder samples were also prepared by thermal decomposition under the same conditions. The powder samples and the oxide layers were characterised by X-ray powder diffraction. The influence of the copper content on the voltammetric response of the electrodes and activity towards oxygen evolution reaction is analysed and correlated with the surface composition of the electrodes by means of X-ray photoelectron spectroscopy data. The analysis of the results reveals that the presence of Cu affects the electrode behaviour and its influence depends on which cation has been replaced. Received: 22 February 1999 / Accepted: 26 October 1999     

Structure and Magnetic Properties of Nickel–Zinc Ferrite Nanoparticles Prepared by Glass Crystallization Method

Summary. The magnetic and microstructure properties of Fe₂O₃–0.4NiO–0.6ZnO–B₂O₃ glass system, which was subjected to heat treatment in order to induce a magnetic crystalline phase (Ni_0.4Zn_0.6-Fe₂O₄ crystals) within the glass matrix, were investigated. DSC measurement was performed to reveal the crystallization temperature of the prepared glass sample. The obtained samples, produced by heat treatment at 765°C for various times (1, 1.5, 2, and 3 h), were characterized by X-ray diffraction, IR spectra, transmission electron microscopy, and vibrating sample magnetometer. The results indicated the formation of spinel Ni–Zn ferrite in the glass matrix. Particles of the ferrite with sizes ranging from 28 to 120 nm depending on the sintering time were observed. The coercivity values for different heat-treatment samples were found to be in the range from 15.2 to 100 Oe. The combination of zinc content and sintering times leads to samples with saturation magnetization ranging from 12.25 to 17.82 emu/g.     

Copper(II)-Catalyzed Decomposition of Hydrogen Peroxide: Catalyst Activation by Halide Ions

Summary.  The catalytic action of Cu(II) on the decomposition of H₂O₂ in near-neutrality aqueous solutions is activated by halide ions. The activation energies amount to 113±7 (parent reaction) and 69.9±1.4 (chloride-activated reaction) kJ · mol⁻¹. Free-radical chain mechanisms are proposed for both the parent reaction and the halide-activated reaction. The catalyst activation caused by halide ions is explained in terms of coordination of halide ligands by both Cu(II) and Cu(I), the coordination causing a higher stabilization of Cu(I) than of Cu(II). At low concentrations, Br⁻ causes an inhibition of the Cu(II)/H₂O₂ reaction. This is explained in terms of an increase of the rate of termination of the chain reaction due to the scavenging effect of OH radicals caused by Br⁻. Received March 27, 2001. Accepted (revised) May 25, 2001.     

Solvothermal Syntheses,Crystal Structures,and Properties of New [Mn(<Emphasis Type="BoldItalic">dien</Emphasis>)<Subscript>2</Subscript>]<Superscript>2+</Superscript> Complexes

Summary.  The two new compounds Mn(dien)₂[MoS₄] (1) and Mn(dien)₂[Mo₂O₂S₆] (2) (dien = diethylenetriamine) were prepared under solvothermal conditions. Both compounds were obtained as phase-pure products. The structures consist of new [Mn(dien)₂]²⁺ cations and isolated tetrahedral [MoS₄]²⁻ (1) or [Mo₂O₂S₆]²⁻ (2) anions. Between the anions and the cations, hydrogen bonding is observed. Compound 1 crystallizes in the tetragonal space group I (a = 10.219(2), c = 9.259(2) ?, Z = 2), whereas 2 crystallizes in the monoclinic space group P2₁/c (a = 8.703(2), b = 18.390(4), c = 14.603(3) ?, β = 103.18(3)°, Z = 4). The thermal behaviour of the thiomolybdates was investigated using difference thermoanalysis (DTA) and thermogravimetry (TG). Both compounds decompose under argon with a single endothermic signal in the DTA curve (peak maximum: 252 (1) and 242°C (2)). Received November 5, 2001. Accepted December 27, 2001     

Polyethylene-supported poly(acrylonitrile-co-methyl methacrylate)/nano-Al2O3 microporous composite polymer electrolyte for lithium ion battery

Nano-Al₂O₃ was doped in poly(acrylonitrile-co-methyl methacrylate) (P(AN-co-MMA)), and polyethylene(PE)-supported P(AN-co-MMA)/nano-Al₂O₃ microporous composite polymer electrolyte (MCPE) was prepared. The performances of the prepared MCPE for lithium ion battery use, including ionic conductivity, electrochemical stability, interfacial compatibility, and cyclic stability, were studied by scanning electron spectroscopy, linear sweep voltammetry, and electrochemical impedance spectroscopy. It is found that the nano-Al₂O₃ significantly affects the MCPE performances. Compared to the MCPE without any nano-Al₂O₃, the MCPE with 10 wt.% nano-Al₂O₃ reaches its best performances. Its ionic conductivity is improved from 2.0 × 10⁻³ to 3.2 × 10⁻³ S cm⁻¹, its decomposition potential is enhanced from 5.5 to 5.7 V (vs Li/Li⁺), and its interfacial resistance on lithium is reduced from 520 to 160 Ω cm². Thus, the battery performance is improved.     

Optical and electrical properties of copper alumina nanoparticles reinforced chlorinated polyethylene composites for optoelectronic devices

The incorporation of transition metal oxide fillers into the polymer matrix through solution mixing polymerization imparts enhanced electrical and thermal properties. The present work focused on the optical properties, crystallinity, thermal stability, temperature-dependent conductivity, dielectric constant and modulus of chlorinated polyethylene/copper alumina (CPE/Cu–Al₂O₃) nanocomposites. Optical absorption measured using an ultraviolet–visible (UV–visible) spectrometer shows enhanced intensity and a blue shift for CPE/Cu–Al₂O₃ nanocomposites. The bandgap energy of CPE/Cu–Al₂O₃ nanocomposites was lower than pure CPE and minimum bandgap energy was recorded for a 7 wt% composites. The X-ray diffraction demonstrates that Cu–Al₂O₃ nanoparticles were uniformly introduced into the CPE matrix. Thermogravimetric analysis (TGA) manifests improved thermal stability of nanocomposites. Dielectric properties decrease with frequency, whereas AC conductivity increases with frequency, and both AC conductivity and dielectric properties increase with temperature. The maximum AC conductivity and dielectric constant were obtained for 7 wt % nanofiller loaded sample. For all systems, the activation energy for electrical conductivity decreases with rising temperatures. The experimental dielectric constant values of CPE nanocomposites were correlated with different theoretical models. The Bruggeman model was in good agreement with the experimental permittivity. The impedance experiments showed a decreasing trend with temperature, indicating the semiconducting nature of prepared nanocomposites.     

Electron Probe Microanalysis of Nitrogen in Glasses and Glass Ceramics

 A homogeneous (phosphate glass) and a heterogeneous (glass ceramic) material were chosen to develop a method for electron microprobe analysis of nitrogen in glasses and glass ceramics. The metaphosphate (50 mole-% P₂O₅, 25 mole-% BaO, 25 mole-% Rb₂O) base glass and the silicate glass (composition of the base glass: 6.9 mole-% Al₂O₃, 21.3 mole-% MgO, 47.3 mole-% SiO₂, 5.1 mole-% CaO, 19.4 mole-% AlN) were melted and cooled down to room temperature. In a second step, the two materials were nitrided by applying dry NH₃ in a special tube furnace. Up to 5 wt.-% of nitrogen could be introduced. The ability of energy dispersive (EDX) as well as wavelength dispersive (WDX) electron probe microanalysis to analyze low contents of light elements in combination with highly concentrated heavy elements was tested both for glasses and for glass ceramics. Measuring conditions had to be optimized to get reliable analytical results as well as to avoid radiation damage of the glasses which may occur especially in the case of wavelength dispersive X-ray analysis. The results were compared with two different analytical methods: inductive coupled plasma analysis and a commercial nitrogen-oxygen-analyzer (the specimen is decomposed by heating and the released gases are analyzed spectroscopically (O) and electrically (N)).     

Fabrication of TiO2/Ti nanotube electrode and the photoelectrochemical behaviors in NaCl solutions

Titanium oxide nanotube electrodes were successfully prepared by anodic oxidation on pure Ti sheets in 0.5 wt.% NH₄F + 1 wt.% (NH₄)₂SO₄ + 90 wt.% glycerol mixed solutions. Nanotubes with diameter 40–60 nm and length 7.4 μm were observed by field emission scanning electron microscope. The electrochemical and photoelectrochemical characteristics of TiO₂ nanotube electrode were investigated using linear polarization and electrochemical impedance spectroscopy techniques. The open-circuit potential dropped markedly under irradiation and with the increase of Cl⁻ concentrations. A saturated photocurrent of approximately 1.3 mA cm⁻² was observed under 10-W low-mercury lamp irradiation in 0.1 M NaCl solution, which was much higher than film electrode. Meanwhile, the highest photocurrent in NaCl solution implied that the photogenerated holes preferred to combine with Cl⁻. Thus, a significant synergetic effect on active chlorine production was observed in photoelectrocatalytic processes. Furthermore, the generation efficiency for active chlorine was about two times that using TiO₂/Ti film electrode by sol–gel method. Finally, the effects of initial pH and Cl⁻ concentration were also discussed.     

Direct Synthesis of Nanocrystalline Hydroxyapatite by Hydrothermal Hydrolysis of Alkylphosphates

Summary.  The influence of reaction conditions (temperature, type of catalyst, time) on the base-catalyzed reaction of mono-, di-, and trialkylphosphates (alkyl = methyl, ethyl, i-propyl, n-butyl) with Ca²⁺ ions and on the structure and composition of the reaction products was studied. The composition of the calcium phosphates depends mainly on the reaction temperature. At temperatures below 100°C, a nanocrystalline solid product transforming into dicalcium phosphate by heating (calcination) was found. Pure nanocrystalline hydroxyapatite was prepared by hydrothermal synthesis at 160°C from mono- and dialkylphosphates. The size of hydroxyapatite crystallites was about 1 nm, the particle size about 150 nm. Agglomerated particles of hydroxyapatite larger than 2 μm were prepared at 200°C. Hydrothermal reaction of trialkylphosphates with Ca²⁺ ions at 200°C produced CaHPO₄. The experimental results were used to propose a reaction mechanism for base-catalyzed hydrothermal reactions of alkylphosphates with Ca²⁺ ions. Received October 4, 2001. Accepted (revised) November 19, 2001     

Catalytic Spectrophotometric Determination of Molybdenum

Summary.  A highly selective, sensitive, and simple catalytic method for the determination of molybdenum in natural and waste waters was developed. It is based on the catalytic effect of Mo(VI) on the oxidation of 2-aminophenol with H₂O₂. The reaction is monitored spectrophotometrically by tracing the oxidation product at 430 nm after 10 min of mixing the reagents. Addition of 800 μg · cm⁻³ EDTA conferred high selectivity; however, interfering effects of Au(III), Cr(III), Cr(VI), and Fe(III) had to be eliminated by a reduction and co-precipitation procedure with SnCl₂ and Al(OH)₃. Mo(VI) shows a linear calibration graph up to 11.0 ng · cm⁻³; the detection limit, based on the 3S _b-criterion, is 0.10 ng · cm⁻³. The unique selectivity and sensitivity of the new method allowed its direct application to the determination of Mo(VI) in natural and waste waters. Received April 11, 2001. Accepted (revised) June 18, 2001     

Quantitative determination of element concentrations in industrial oxide materials by laser-induced breakdown spectroscopy

Calibration-free laser-induced breakdown spectroscopy (CF-LIBS) method is employed for quantitative determination of oxide concentrations in multi-component materials. Industrial oxide materials from steel industry are laser ablated in air, and the optical plasma emission is collected by spectrometers and gated detectors. The temperature and electron number density of laser-induced plasma are determined from measured LIBS spectra. Emission lines of aluminium (Al), calcium (Ca), iron (Fe), manganese (Mn), magnesium (Mg), silicon (Si), titanium (Ti), and chromium (Cr) of low self-absorption are selected, and the concentration of oxides CaO, Al₂O₃, MgO, SiO₂, FeO, MnO, TiO₂, and Cr₂O₃ is calculated by CF-LIBS analysis. For all sample materials investigated, we find good match of calculated concentration values (C _CF) with nominal concentration values (C _N). The relative error in oxide concentration, e _r = |C _CF − C _N|/C _N, decreases with increasing concentration and it is e _r ≤ 100% for concentration C _N ≥ 1 wt.%. The CF-LIBS results are stable against fluctuations of experimental parameters. The variation of laser pulse energy over a large range changes the error by less than 10% for major oxides (C _N ≥ 10 wt.%). The results indicate that CF-LIBS method can be employed for fast and stable quantitative compositional analysis of multi-component materials.     

Kinetic Determination of Iodide Based on its Effect on the Hydrogen Peroxide Oxidation of Triflupromazine

Summary.  A new selective, sensitive, and simple kinetic method is developed for the determination of trace amounts of iodide. The method is based on the catalytic effect of iodide on the reaction of triflupromazine (TFP) with H₂O₂. The reaction is followed spectrophotometrically by tracing the oxidation product at 498 nm within 1 min after addition of H₂O₂. The optimum reaction conditions are TFP (0.4 × 10⁻³ M), H₂SO₄ (1.0M), H₃PO₄ (2.0M), and H₂O₂ (1.6M) at 30°C. Following this procedure, iodide can be determined with a linear calibration graph up to 4.5 ng ċ cm⁻³ and a detection limit of 0.04 ng ċ cm⁻³, based on the 3 S_b criterion. The method can also be applied to the determination of iodate and periodate ions. Determination of as little as 0.2, 1.0, 2.0, and 4.0 ng ċ cm⁻³ of I⁻, IO₃ ^-, or IO₄ ^- in aqueous solutions gave an average recovery of 98% with relative standard deviations below 1.6% (n = 5). The method was applied to the determination of iodide in Nile river water and ground waters as well as in various food samples after alkaline ashing treatment. The method is compared with other catalytic spectrophotometric procedures for iodide determination. Received January 19, 2001. Accepted (revised) March 12, 2001     

Kinetic studies on the hydrogenation of nitrate in water using Rh/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Rh-Cu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Liquid-phase reduction NO ₃ ⁻ using monometallic and bimetallic catalysts (5% Rh/Al₂O₃, 5% Rh-0.5% Cu/Al₂O₃, 5% Rh-1.5% Cu/Al₂O₃, 5% Rh-5% Cu/Al₂O₃ and a physical mixture of 5% Rh/Al₂O₃ and 1.5% Cu/Al₂O₃) was studied in a slurry reactor operating at atmospheric pressure. Kinetic measurements were performed for a low concentration of nitrate (0.4 × 10⁻³−3.2 × 10⁻³ mol dm⁻³) and the temperature range 293–313 K. From the experimental data, it was found that the reduction of nitrate is first order with respect to nitrate. On the basis of the rate constants, the apparent activation energy was established using a graphic method. Published in Russian in Kinetika i Kataliz, 2007, Vol. 48, No. 6, pp. 881–886. This article was submitted by the authors in English.     

Electrochemical performances of inorganic membrane coated electrodes for li-ion batteries

In the present study, we prepared new Li-ion batteries with inorganic membrane-coated electrodes fabricated by the direct coating of a 400-nm-sized Al₂O₃ particles onto the anodes and studied their charge–discharge characteristics for the first time. Being made of 94 wt.% Al₂O₃ powder and 6 wt.% polymeric binder, the membranes on the anodes showed excellent wettability with the liquid electrolytes, due to their high porosity and capillarity. The Li-ion batteries prepared by the assembly of the inorganic membrane-coated electrodes showed excellent charge–discharge behavior compared to conventional Li-ion batteries with a polymeric separator. However, their high-rate performance was affected by the binder contents in the inorganic membranes. The thermal properties of the Li-ion battery with the inorganic membrane-coated electrodes were compared with those of a conventional one with a polymeric separator.     

Ultrasound technique as a tool for high-rate incorporation of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> in NiCo layers

NiCo–Al₂O₃ composite coatings were prepared by electrodeposition in a sulfamate plating bath containing Al₂O₃ particles to be co-deposited under sonication. For reliable determination of the microstructure, detailed studies on composite cross-sections were carried out by energy-dispersive spectrometer (matrix composition, particle content) and FE-SEM/electron backscattered diffraction data (particle distribution, grain size), accompanied by XRD analyses concerning texture, lattice parameter, grain size, and residual stress. The NiCo matrix with a Co/Co + Ni ratio up to 0.4 is a face-centered cubic solid solution with <100> and <110> fiber textures. The distribution of the particles (size 250 nm) was well-dispersed and enhanced up to 15 wt.% by ultrasound application during plating. Vickers hardness increased up to 50% by dispersion hardening. First-order residual stress in the matrix increased with rising Co content, thus decreasing wear resistance and revealing the complex of composite properties with partially opposite effects.     

Colloid stability of electrostatically stabilized sols

 The dependence of the stability of SiO₂ and Al₂O₃ sols on the pH of their medium has been studied. Vapor adsorption isotherms on powders were prepared from acidic and basic sols, the immersion enthalpy (heat) of samples containing preadsorbed water have been determined and, also, the reversibility of the sol ⇌ xerogel transformation, i.e. the peptizability of the powders, has been investigated. Based on the flocculation values determined with KCl, the sols have been classified into three groups. The stability of highly hydrophilic sols (acidic SiO₂- and Al₂O₃-sols) is ensured by a thick continuous diffuse lyosphere formed around the particles, as the continuity principle by Ostwald–Buzágh suggests. In this case, no electric charge is needed for ensuring stability. These sols are thermodynamically stable (group 1). Sols with medium stability are stabilized by the electrical double layer around the particles and by 1–2 layers of adsorbed water. The flocculation value of these sols is determined by the electrostatic interaction, whereas the peptizability of the flocs is related to formation of water layers. Such sols are the basic SiO₂- and Al₂O₃-sols (group 2). Sols of low stability are of hydrophobic nature. Their flocculation value with 1:1 electrolytes is smaller than 0.1 molkg^-1. The transformation process sol ⇒ floccule ⇒ xerogel is mostly irreversible. There are a lot of such sols (group 3). The existence of a hydrosphere is proved by the almost identical value of the hydration energy for both the acidic and the basic SiO₂ sols, in spite of an order of magnitude difference in the flocculation value. The remnants of adsorbed water after drying hinders sintering of the particles and ensures the peptizability of powders. The highly hydrophilic sols (sequence of hydrophilicity: SiO₂> Al₂O₃>FeO OH ⋅ 0.5 H₂O) are all oxides which are formed in acidic media. Received: 25 May 1997 Accepted: 13 October 1997     

Electronic Structure and Size of TiO2 Nanoparticles of Controlled Size Prepared by Aerosol Methods

Summary.  A complete characterization of nanostructures has to deal both with electronic structure and dimensions. Here we present the characterization of TiO₂ nanoparticles of controlled size prepared by aerosol methods. The electronic structure of these nanoparticles was probed by X-ray absorption spectroscopy (XAS), the particle size by atomic force microscopy (AFM). XAS spectra show that the particles crystallize in the anatase phase upon heating at 500°C, whereas further annealing at 700°C give crystallites of 70% anatase and 30% rutile phases. Raising the temperature to 900°C results in a complete transformation of the particles to rutile. AFM images reveal that the mean size of the anatase particles formed upon heating at 500°C is 30 nm, whereas for the rutile particles formed upon annealing at 900°C 90 nm were found. The results obtained by these techniques agree with XRD data. Received October 5, 2001. Accepted (revised) December 6, 2001     

Structure and Magnetic Properties of Nickel–Zinc Ferrite Nanoparticles Prepared by Glass Crystallization Method

The magnetic and microstructure properties of Fe₂O₃–0.4NiO–0.6ZnO–B₂O₃ glass system, which was subjected to heat treatment in order to induce a magnetic crystalline phase (Ni_0.4Zn_0.6-Fe₂O₄ crystals) within the glass matrix, were investigated. DSC measurement was performed to reveal the crystallization temperature of the prepared glass sample. The obtained samples, produced by heat treatment at 765°C for various times (1, 1.5, 2, and 3 h), were characterized by X-ray diffraction, IR spectra, transmission electron microscopy, and vibrating sample magnetometer. The results indicated the formation of spinel Ni–Zn ferrite in the glass matrix. Particles of the ferrite with sizes ranging from 28 to 120 nm depending on the sintering time were observed. The coercivity values for different heat-treatment samples were found to be in the range from 15.2 to 100 Oe. The combination of zinc content and sintering times leads to samples with saturation magnetization ranging from 12.25 to 17.82 emu/g.     

Catalytic Combustion of Ethyl Acetate over Al2O3- Ce0.5Zr0.5O2 Supported Metal Oxide Catalysts

The catalysts for the combustion of ethyl acetate were prepared using Fe, Co, Cu, Cr, and Mn metal oxide as active components supported on Al₂O₃-Ce_0.5Zr_0.5O₂ mixed oxides and characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), oxygen storage capacity measurement, BET surface area, XPS measurement, and activity test. According to the results of characterization, it was found that Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) catalysts presented excellent activity for the catalytic combustion of ethyl acetate, because of the more reducible species and high reducibility of the catalysts. For ethyl acetate oxidation, more than 99% conversion was achieved at 245 °C over catalysts Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio), indicating that the catalysts had great potential for wide use.