Synthesis, growth, optical, mechanical, dielectric and thermal properties of 4-chloro-4'-chlorobenzylidene aniline single crystal

The organic material 4-chloro-4′-chlorobenzylidene aniline (CCBA) was synthesized and confirmed by NMR and FTIR spectral analyses. CCBA crystal was grown from chloroform by slow evaporation at room temperature and the single crystal cell parameters were determined by single crystal X-ray diffraction method. The perfection of the grown crystal was analyzed by high resolution X-ray diffraction rocking curve analysis. Fluorescence spectrum indicated violet emission at 428 nm. The range of optical absorbance was ascertained by recording UV–vis–NIR spectrum. Load dependant microhardness measurements on this crystal revealed the mechanical behavior of the material. Stiffness constant, Meyer index and yield strength of CCBA crystal were calculated. Dielectric studies were carried out to estimate the dielectric parameters of the grown crystal in the frequency range from 100 Hz to 100 kHz. The thermal behavior of CCBA was investigated using differential scanning calorimetry (DSC) and no phase transition was identified in the temperature region 30–100 °C. Further, the CCBA crystal was subjected to open aperture Z-scan studies in order to investigate the third order nonlinear optical (NLO) properties of CCBA crystal.     

Growth and characterization of thiosemicarbazide hydrochloride: a semiorganic NLO material

Thiosemicarbazide hydrochloride (TSCHCL) was synthesized by mixing thiosemicarbazide and hydrochloride in 1:1 molar ratio in double distilled water. Single crystals of TSCHCL were grown by slow evaporation at room temperature and were characterized by single crystal X-ray diffraction study to determine the molecular structure and by FT-IR, ¹H and ¹³C NMR spectral analyses to confirm the synthesized compound. Thermogravimetric and differential thermal analyses reveal the thermal stability of the crystal. The transmission spectrum of TSCHCL showed that the crystal is transparent in the wavelength range 380–1100 nm. High resolution X-ray diffractometry (HRXRD) was employed to evaluate the perfection of the grown crystal. Mechanical properties of the grown crystal were studied using Vickers microhardness test. Second harmonic generation efficiency of the powdered TSCHCL was tested using Nd:YAG laser and is ∼1.5 times that of potassium dihydrogen orthophosphate.     

Fluidification of Concentrated Aqueous Colloidal Silica Suspensions by Adsorption of Low-Molecular-Weight Poly(ethylene oxide)

This paper deals with the effect of different low-molecular-weight poly(ethylene oxide)s on the rheology of concentrated aqueous colloidal silica suspensions (volume fraction >0.2) with the aim of obtaining well-dispersed media. Results are correlated with the physico-chemical characteristics of the systems that govern the ranges of the various operating interactions, i.e., mainly surface coverage, molecular weight of the polymer, and ionic strength of the medium. Optimization of the fluidification occurs to be strongly linked to these parameters. An unexpected effect of free polymer bulk concentration leads to improved fluidification when the characteristic lengths of the system are correctly adjusted; it has been interpreted in the frame of recent theories.     

Effect of structural stress on the intercalation rate of kaolinite

Particle size in kaolinite intercalation showed an inverse reactivity trend compared with most chemical reactions: finer particles had lower reactivity and some of the fine particles cannot be intercalated. Although this phenomenon was noted in the early 1960s and several hypotheses have been reported, there is no widely accepted theory about the unusual particle size response in the intercalation. We propose that structural stress is a controlling factor in the intercalation and the stress contributes to the higher reactivity of the coarser particles. In this study, we checked the structural deformation spectroscopically and indirectly proved the structural stress hypothesis. A Georgia kaolinite was separated into nine size fractions and their intercalations by hydrazine monohydrate and potassium acetate were investigated with X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) analyses. The apical Si-O band of kaolinite at 1115 cm(-1) shifted to 1124 cm(-1) when the mineral was intercalated to 1.03 nm by hydrazine monohydrate, and its strong pleochroic properties became much weaker. Similar reduction in pleochroism was observed on the surface OH bands of kaolinite after intercalation. Both the bending vibrations of the inner OH group at 914 cm(-1) and of the surface OH group at 937 cm(-1) shifted to 903 cm(-1) after intercalation by hydrazine. A new band for the inner OH group appeared at 3611 cm(-1) during the deintercalation of the 1.03 nm hydrazine kaolinite complex. Pleochroism change in the apical Si-O band suggested the tetrahedra had increased tilt with respect to the (001) plane. The tilt of the Si-O apical bond could occur only if the octahedra had also undergone structural rearrangement during intercalation. These changes in the octahedral and tetrahedral sheets represent some change in the manner of compensation for the structural misfit of the tetrahedral sheet and octahedral sheet. As the lateral dimensions of a kaolinite particle increases, the cumulative degree of misfit increases. Intercalation breaks the hydrogen bonds between layers and allows for the structure to reduce the accumulated stress in some other manner. The reversed size effect on intercalation probably was not caused by crystallinity differences as reported in the literature, because the Hinckley and Lietard crystallinity indices of the four clay fractions were very close to each other. Impurities, such as dickite- or nacrite-like phases are not significant in the studied sample as suggested by the XRD and IR results, they are not the main reasons for the lower reactivity of the finer particles.     

Rheology and Permeability of Crosslinked Polyacrylamide Gel

Gels produced by crosslinking polyacrylamide solutions with chromium (III) have been characterized by dynamic rheology studies. To vary the gel strength, different polymer concentrations were used, while keeping the temperature, salinity, and crosslinker concentration constant. Both the loss and storage moduli increased with the polymer concentration for this gel system. The storage modulus at the end of the gelation was used to characterize the gel strength. Steady-state water flow experiments through gel-filled capillary tubes were performed, with the aim of linking the gel strength and flow behavior. The permeability was found to be a function of the water flow rate (velocity) and polymer concentration. Two parameters were used to characterize the flow behavior, intrinsic gel permeability and elasticity index, which are each functions of the polymer concentration. However, only one parameter is needed to fully identify the flow and rheological gel properties, as the elasticity index and storage modulus are linked by a power-law relationship. The loss modulus and intrinsic permeability are correlated with the storage modulus and elasticity index, respectively. A theoretical model for this behavior linking both gel properties based on the dual domain structure was used to demonstrate that the flow and rheological behavior of the gel are indeed related and that the gel strength controls the water permeability. Implications for prediction of flow of water through gels emplaced in a porous medium are discussed.     

Adsorption of 1,4-Benzenedithiol on Gold and Silver Surfaces: Surface-Enhanced Raman Scattering Study

The adsorption behavior of 1,4-benzenedithiol (1,4-BDT) on colloidal gold and silver surfaces has been investigated by means of surface-enhanced Raman scattering (SERS). 1,4-BDT chemisorbed dissociatively on both gold and silver surfaces but as mono- and dithiolate, respectively. Regardless of the bulk concentration of 1,4-BDT, only a monolayer was assembled on the silver surface with a flat orientation by forming two Ag–S bonds. On the gold surface, the monothiolate species,1,4-BDT⁻¹, appeared to assume a rather flat orientation at a very low surface coverage, but as the surface coverage was increased, the adsorbate took a perpendicular orientation. Furthermore, when the bulk concentration of 1,4-BDT was close to that required for a full-monolayer coverage limit, a band assignable to the S–S stretching vibration appeared at 536 cm⁻¹ in the gold sol SERS spectra. A separate ellipsometry measurement performed with vacuum-evaporated gold substrates revealed that up to tetralayers could be assembled on gold in 1 mM n-hexane solution of 1,4-BDT while at best a bilayer formed in either methanol or ethanol solution. The different adsorbate structure of 1,4-BDT on gold and silver was overall quite comparable to that of p-xylene-α,α′-dithiol.     

Influence of Sodium Periodate and Tyrosinase on Binding of Alginate to Adlayers of Mytilus edulis Foot Protein 1

Mytilus edulis foot protein 1 (Mefp-1) is the most well-characterized component of this sea mussel's adhesive plaque. The plaque is a condensed, heterogeneous mixture consisting of a large proportion of cross-linked biopolymers that bonds the mussel to a chosen mooring. Mefp-1 is densely populated with lysine and -3,4-dihyroxyphenylalanine ( -dopa) residues incorporated into a repeating amino acid sequence motif. It has been proposed that one plaque cross-linking reaction is the nucleophilic addition of the ε-amino groups of the lysine residues into the oxidized catechol (o-diphenol) functionality (quinone) of the -dopa residues. In order to determine if this reaction occurs in adlayers of Mefp-1, a previously developed assay for ε-amino groups was applied. Adlayers of Mefp-1 were exposed to an oxidant, either the enzyme, mushroom tyrosinase, or sodium periodate. Binding of alginate to adlayers was used to probe for accessibility of ε-amino groups. It was found that lysine residues lose the ability to bind alginate after exposure to sodium periodate, but that this loss is not clearly due to a reaction with -dopa residues. There is a slight decrease of binding of alginate to adlayers of Mefp-1 exposed to either active or thermally deactivated mushroom tyrosinase, probably due to the obstruction of binding sites by bound enzyme. Adsorption kinetics of mushroom tyrosinase onto adlayers of Mefp-1 for active and thermally inactivated enzyme were nearly identical. Attenuated total reflection Fourier transform infrared spectroscopy was used to characterize these interactions at a germanium (Ge) interface.     

Silylating Agents Grafted onto Silica Derived from Leached Chrysotile

Silica from leached chrysotile fibers (SILO) was silanized with trialkoxyaminosilanes to yield inorganic–organic hybrids designated SILx (x=1–3). The greatest amounts of the immobilized agents were quantified as 2.14, 1.90, and 2.18 mmol g⁻¹ on SIL1, SIL2, and SIL3 for –(CH₂)₃NH₂,–(CH₂)₃NH(CH₂)₂NH₂, and –(CH₂)₃NH(CH₂)₂NH(CH₂)₂NH₂ groups attached to the inorganic support. The infrared spectra for all modified silicas showed the absence of the Si–OH deformation mode, originally found at 950 cm⁻¹, and the appearance of asymmetric and symmetric C–H stretching bands at 2950 and 2840 cm⁻¹. Other important bands associated with the organic moieties were assigned to ν_as(NH) at 3478 and ν_sym(NH) at 3418 cm⁻¹. The NMR spectrum of the solid precursor material suggested two different kinds of silicon atoms: silanol and siloxane groups, between −90 and 110 ppm; however, additional species of silicon that contain the organic moieties bonded to silicon at −58 and −66 ppm appeared after chemical modification. These modified silicas showed a high adsorption capacity for cobalt and copper cations in aqueous solution, in contrast to the original SILO matrix, confirming the unequivocal anchoring of silylating agents on the silica surface.     

Transport Properties of Compact Clays: I. Conductivity and Permeability

Conductivity and permeability of model and natural clays have been studied experimentally. Local properties such as porosity and zeta potentials were measured as functions of the electrolyte solutions. Whenever possible, experimental data were compared to numerical data obtained for random packings of grains of arbitrary shape, and a good agreement was found between them.     

Electroosmotic Flow of a General Electrolyte Solution through a Fibrous Medium

Although hydrotropy is extensively used in industry, the molecular mechanism of hydrotropic solubilization has not been completely elucidated yet. In this paper the interaction between a nonionic surfactant (ethoxylated fatty alcohol containing between five and six oxyethylenic units) and sodium p-toluene sulfonate is examined. Surface tension measurements confirm that the hydrotropic effect occurs at a concentration in which the hydrotropes self-associate. Photon correlation spectroscopy studies show that for this concentration of hydrotropes a drastic reduction in the surfactant micellar radius occurs. Furthermore the luminescence of the hydrotrope used as a fluorescence probe indicates that at low concentrations p-toluene sulfonate dissolves in the surfactant micelles but beyond the minimum concentration for hydrotropic solubilization the hydrotrope is present in the aqueous phase. These results suggest that the hydrotropic effect is related to alterations in the water structure induced by the hydrotrope molecules and to the presence of hydrotrope aggregates that furnish an appropriate niche for the surfactant amphiphile.     

The Heavy-Atom Effect on the Photophysics of Aromatic Hydrocarbons in the Presence of Solid Clays

The exchange of the original cation present on a Laponite clay (usually Na⁺) for heavy atoms such as Rb⁺, Cs⁺, and Tl⁺ significantly alters the emission characteristics of some aromatic hydrocarbons (p-terphenyl, naphthalene, pyrene, and biphenyl). The increase of the atomic mass of the cation induces a decrease of the fluorescence emission simultaneous with an increase of the emission in the region of lower energies of the spectra, ascribed to the phosphorescence of those hydrocarbons. Time-resolved experiments for the pyrene–clay system showed a decrease of singlet lifetimes for the heavier atoms. Hydrocarbon aggregates were also detected from both the emission spectra and the time-resolved studies. The “excimer-like” emission showed longer lifetimes (10–25 ns) than the monomolecular hydrocarbons (1–3 ns), as already found for other similar systems. The amount of aggregates increased for the heavier cations due to the smaller surface available on the clay particles. Experiments increasing the amount of Tl⁺ in samples containing a constant concentration of naphthalene allowed evaluation of the distance between the heavy atoms and the probe on the clay surface. The Perrin model treatment was used and resulted in approximately R₀=9.2 Å.     

Thermodynamic quantities of surface formation of aqueous electrolyte solutions. V. Aqueous solutions of aliphatic amino acids

The surface tension of aqueous solutions of glycine, L-alanine, L-valine, and L-leucine has been observed using the drop volume method as a function of temperature and concentration. The L-leucine molecules form an adsorbed film, while glycine affects the water surface in accordance with simple salts which dissociate into cations and anions completely. The surface tension data have been analyzed in view of K. Motomura's thermodynamic treatment (J. Colloid Interface Sci.64, 348 (1978)), and the thermodynamic quantities relevant to the surface have been shown systematically.     

Efficient Photocatalytic Degradation of Environmental Pollutants with Mass-Produced ZnS Nanocrystals

Photocatalytic degradation of water pollutants using nanometersized semiconductor colloids is an emerging area of environmental remediation. The synthesis of semiconductor nanocrystals (NCs), however, can be costly and result in low product yields. For large-scale photocatalytic application in environmental remediation, cost-effective production of the semiconductor NCs would be ideal. Demonstrated in this report is the efficient photocatalytic degradation of p-nitrophenol (pNP) and Acid Orange 7 (AO7) using ZnS nanocrystals (3 to 5 nm diameter) produced in gram quantities with >50% product yield. The pNP half-life in ZnS nanocrystal photocatalyzed reactions was about 1.95 to 2.45 min, whereas in comparable TiO₂ reactions, the pNP half-lives were in the range of 12 to 15 min. Absorption spectra of the photocatalysis reactions suggested the decolorization of pNP without any noticeable formation of phenolic intermediates, implying a mechanism that involves a pNP ring opening via a radical mediated attack. Likewise, the degradation of AO7 was suggested to occur via an oxidative pathway involving hydroxyl radicals formed at the photocatalyst/liquid interface. Optimum conditions for AO7 degradation such as pH, photocatalyst-to-AO7 ratio, and photocatalyst surface passivation were similar to those for pNP. By demonstrating efficient mineralization of these model pollutants using mass-produced ZnS nanocrystals, we hope to lay the foundations necessary for development of large-scale, field-applicable systems.     

Substituent Effects on Binding Constants of Carotenoids to n-Heptane/AOT Reverse Micelles

The absorption spectra of 6′-apo-β-caroten-6′-ol (1), 6′-apo-β-caroten-6′-oic acid (2), and ethyl 6′-apo-β-caroten-6′-oate (3) were analyzed in homogeneous media and in reversed micelles of AOT (sodium 1,4-bis(2-ethylhexyl) sulfosuccinate) in n-heptane. The possible solute–solvent interactions of these compounds were analyzed in pure solvents by Taft and Kamlet's solvatochromic comparison method. These carotenoids show sensitivity similar to that of medium polarity-polarizability as measured by π*. Moreover, the absorption spectra of carotenoid 3 and to much less extent carotenoid 2 display broadening of the visible bands induced by polar solvents characteristic of carotenoids that contain a carbonyl functional group in conjugation with the carbon–carbon π-electron system. They are also sensitive to the ability of the solvent to accept protons in a hydrogen bond interaction measured by β. This sensitivity follows the expected order: 2>1>3. In the reverse micellar system, while the spectra for 3 remain unchanged, the intensity of the absorption band characteristic of n-heptane for 1 and 2 decreases as the AOT concentration increases, and a new band develops. This new band is attributed to the solute bound to the micelle interface. These changes allowed us to determine the binding constant (K_b) between these compounds and AOT. At W₀=[H₂O]/[AOT]=0 the values of K_b of 326±5 and 6.2±0.3 were found for the acid 2 and the alcohol 1, respectively. The strength of binding is interpreted considering their hydrogen-bond donor ability and the solubility in the organic pseudophase. For 1K_bdecreases as W₀ is increased, while for 2 no variation was observed. These effects are discussed in terms of carotenoid–water competition for interfacial binding sites.     

Assembly of Alternated Multivalent Ion/Polyelectrolyte Layers on Colloidal Particles. Stability of the Multilayers and Encapsulation of Macromolecules into Polyelectrolyte Capsules

Alternating adsorption of multivalent ions and oppositely charged polyelectrolytes on colloid particles has been investigated. Multilayer films composed of Tb³⁺/polysterene sulfonate (PSS) and 4-pyrene sulfate/polyallylamine (PAH) were successfully assembled on polysterene sulfonate (PS) and melamine formaldehyde (MF) latex particles. The amount of assembled material was estimated by fluorescence and the linear growth of the film versus the number of layers was demonstrated. These multilayers are not stable and can be decomposed by salt and temperature. Dissolution of MF particles leads to formation of hollow capsules consisting of multivalent ion/polyelectrolyte multilayers. Comparative analysis of the capsules was done by confocal and scanning force microscopy. Complex hollow spheres consisting of Tb³⁺/PSS or 4-PS/PAH as an inner shell and stable PSS/PAH as an outer shell were produced. Due to selective permeability of the outer shell after degradation of the inner shell the multivalent ions are released out of the capsule while the polyelectrolytes fill the capsule interior. This is indicative of swelling of the capsule by osmotic pressure. The filled capsules were studied by confocal and scanning electron microscopy. Possibilities of encapsulating macromolecules in defined amounts per capsule are discussed.     

Novel sintering behavior of polystyrene nanolatex particles in the filming process

The filming process of polystyrene nanolatex (NPS) particles was studied by a combination of various methods. For a constant annealing time of 1 h, the AFM images showed that the deformation and interdiffusion temperatures of NPS particles were ca. 90 and 100-110 degrees C, respectively. In spin-lattice relaxation measurements of solid state NMR, it is found that T1L, T1S, and PL increased significantly after annealing at 90 and 100 degrees C for 1 h. DSC results showed that there was a exothermic peak near Tg after annealing for 1 h at the elected temperatures below 95 degrees C; otherwise, the exothermic peak disappeared after annealing at 100 degrees C or above. The apparent density of NPS increased suddenly in the temperature range of 90-110 degrees C. The results indicated that the macromolecules are highly constrained in NPS particles, leading to higher conformational energy, with more free volume and segments less restricted, which are the driving forces for the particles sintering at a lower temperature compared to the micro-PS particles with larger diameter.     

Flow of Multicomponent Electrolyte Solutions through Narrow Pores of Nanofiltration Membranes

The slow flow of a multicomponent electrolyte solution in a narrow pore of a nanofiltration membrane is considered. The well-known semiempirical method of subdivision of electrical potential into quasi-equilibrium and streaming parts and the definition of streaming concentrations and pressure are discussed. The usefulness of this tool for solving the electrohydrodynamic equations is shown and justified: the use of a small parameter enables a system of electrohydrodynamic partial differential equations to be reduced to a system of ordinary differential equations for streaming functions. Boundary conditions for streaming functions at both the capillary inlet and outlet are derived. The proposed model is developed for the flow of a multicomponent electrolyte solution with an arbitrary number of ions. This is coupled with (i) the introduction of specific interactions between all ions and the pore wall and (ii) the inclusion of the dissociation of water in both conservation and transport equations. Effective distribution coefficients of ions are introduced that are functions of both the specific interaction potentials and the surface potential of the nanofiltration membrane material. The axial dependency of surface potential is expressed by the use of a charge regulation model from which the discontinuity in electric potential and ion pore concentrations at the pore inlet and outlet can be described.A relation between the frequently used capillary and homogeneous models of nanofiltration membranes is developed. An example of application of the homogeneous model for interpretation of experimental data on nanofiltration separation of electrolyte solutions is presented, which shows a reasonable predictive ability for the homogeneous model.     

Application of the JKR Method to the Measurement of Adhesion to Langmuir-Blodgett Cellulose Surfaces

The JKR method has been applied for studying adhesion between poly(dimethylsiloxane) (PDMS) caps and Langmuir–Blodgett cellulose surfaces including the substrate, hydrophobized mica, and two flat mineral surfaces, bare mica and glass. The self-adhesion of PDMS caps and oxidized PDMS caps are included as a reference to compare with literature data. The results of the measurements have been compared with previous studies using the surface force apparatus and similar systems. A satisfactory agreement is obtained for simple systems showing no, or very limited, hysteresis between loading and unloading curves. In several cases, however, a large hysteresis is found between loading and unloading curves, with a larger adhesion measured from the pull-off force than from the JKR-curve determined on loading. This is, for instance, the case for PDMS against cellulose. The situation is analogous to that found in wetting studies showing a large hysteresis between advancing and receding contact angles.     

Photochromic Inorganic/Organic Self-Assembled Superlattice Films

Phosphotungstic acid (PW₁₂) and 1,10-diaminodecane (1,10-DAD) molecules have been alternatively assembled on 3-aminopropyltriethyoxysilane modified quartz or silicon substrate to form multicomposite mutilayer thin films by the molecular deposition technique. Thus-obtained films were characterized by UV-visible, XRD, X-ray reflection (XRR), and XPS spectra. Results show that the layer-by-layer self-assembly of PW₁₂ and 1,10-DAD leads to a well-ordered superlattice-layered structure with a d-spacing of 3.19 nm, which exhibits extremely exciting photochromic properties. Based on the experimental data, a presumable interlayer structural model has also been suggested.