Nonlinear vibration analysis of functionally graded beams considering the influences of the rotary inertia of the cross section and neutral surface position

In the paper work, the nonlinear vibration response of functionally graded (FG) Euler–Bernoulli beam resting on elastic foundation is studied. Based on von Kármán’s geometric nonlinearity, the partial differential governing equations describing the nonlinear vibration of FG Euler–Bernoulli beam are derived from Hamilton’s principle and are reduced to an ordinary nonlinear differential equation with quadratic and cubic nonlinear terms via Galerkin’s procedure. Due to unsymmetrical material variation along the thickness of FG beam, the neutral surface concept is proposed to remove the stretching and bending coupling effect and the rotary inertia of the cross section is incorporated to obtain an analytical solution. Numerical results are presented to show the effects of the nonlocal parameters and vibration amplitude on the frequency responses. This results may be useful in design and engineering applications.     

Refined theories may be needed for vibration analysis of structures with overhang

The effect of shear deformation and rotary inertia terms on the free vibration of a beam with overhang was investigated. A recently proposed modified Timoshenko-type equations of motion were used to analyze the vibration of the structure. Two different sets of boundary conditions, with either a fixed or hinged end support, were studied. The results were compared with those obtained for the classical Bernoulli–Euler beam theory. The comparison shows that for a hinged end beam with very long overhang, where the span between the supports is less than one tenth of the overall beam length, the classical theory significantly overestimates the values of the fundamental natural frequencies, even for isotropic shear rigidity. On the other hand, the span effect is reversed for the clamped end beam, for which a relatively significant difference between the classical theory and shear theory results may occur only for a long span. For transversely isotropic beams, the refined theory predictions of the fundamental natural frequencies may be much smaller than those obtained through the rigid shear theory, especially for short span hinged end beams and long span clamped end beams.     

Geometrically exact planar beams with initial pre-stress and large curvature: Static configurations,natural frequencies,and mode shapes

Within this paper, an analytical formulation is provided and used to determine the natural frequencies and mode shapes of a planar beam with initial pre-stress and large variable curvature. The static configuration, mode shapes, and natural frequencies of the pre-stressed beam are obtained by using geometrically exact, Euler–Bernoulli beam theory. The beam is assumed to be not shear deformable and inextensible because of its slenderness and uniform, closed cross-section, as well as the boundary conditions under consideration. The static configuration and the modal information are validated with experimental data and compared to results obtained from nonlinear finite-element analysis software. In addition to the modal analysis about general static configurations, special consideration is given to an initially straight beam that is deformed into semi-circular and circular static configurations. For these special circular cases, the partial differential equation of motion is reduced to a sixth-order differential equation with constant coefficients, and solutions of this system are examined. This work can serve as a basis for studying slender structures with large curvatures.     

Theoretical analysis of transient waves in a simply-supported Timoshenko beam by ray and normal mode methods

The dynamic transient responses of a simply-supported Timoshenko beam subjected to an impact force are investigated by two theoretical approaches – ray and normal mode methods. The mathematical methodology proposed in this study for the ray method enable us to construct the solution for the interior source problem and to extend to solve the complicated problem for the multi span of the Timoshenko beam. Numerical results based on these two approaches are compared. The comparison in this study indicates that the normal mode method is more computationally efficient than the ray method except for very short time after the impact. The long-time transient responses are easily calculated using the normal mode method. It is shown that the average long-time transient response converges to the corresponding static value. The Timoshenko beam theory is more accurate than the Bernoulli–Euler beam theory because it includes shear and rotary inertia. This study also provides the slender ratio for which the Bernoulli–Euler beam can be used for the transient-response analysis of the displacement. Moreover, the resonant frequencies obtained from finite element calculation based on the three-dimensional model are compared with the results calculated using the Timoshenko beam and Bernoulli–Euler beam theories. It is noted in this study that the resonant frequency can be accurately determined by the Timoshenko beam theory if the slender ratio is larger than 100, and by the Bernoulli–Euler beam theory if the slender ratio is larger than 400.     

多场作用下输流单层碳纳米管的动力学特性

以非局部弹性理论为基础,采用欧拉-伯努利梁模型,考虑管型区域内滑移边界条件以及碳纳米管的小尺度效应,应用哈密顿原理获得了温度场与轴向磁场共同作用下的输流单层固支碳纳米管（SWCNT）的振动控制方程以及边界条件,依靠微分变换法（DTM法）对此高阶偏微分方程进行求解,通过数值计算研究了多场中单层固支输流碳纳米管的振动与失稳问题。结果表明：温度场、轴向磁场强度、Knudsen数及小尺度参数都会对系统振动频率以及失稳临界流速产生影响。     

Exact solution for axial and transverse dynamic response of functionally graded nanobeam under moving constant load based on nonlocal elasticity theory

This paper aims to analyze the axial and transverse dynamic response of a functionally graded nanobeam under a moving constant load. The governing equations are obtained using the Hamilton principle and nonlocal Euler–Bernoulli beam theory. The mechanical properties vary in the thickness direction. The simply supported boundary condition is assumed and using the Laplace transform, the exact solution for the transverse and axial dynamic response is presented. Some examples were used to analyze nonlocal parameters such as power law index of FG materials, aspect ratio and the velocity of a moving constant load and also their influence on axial and transverse dynamic and maximum deflections. By obtaining a good agreement between the presented natural frequencies in this study and previous works, the results of this study are validated.     

Stability of fluid conveying nanobeam considering nonlocal elasticity

In this study, the nonlocal Euler–Bernoulli beam theory is employed in the vibration and stability analysis of a nanobeam conveying fluid. The nanobeam is assumed to be traveling with a constant mean velocity along with a small harmonic fluctuation. In the considered analysis, the effects of the small-scale of the nanobeam are incorporated into the equations. By utilizing Hamilton’s principle, the nonlinear equations of motion including stretching of the neutral axis are derived. Damping effect is considered in the analysis. The closed form approximate solution of nonlinear equations is solved by using the multiple scale method, a perturbation technique. The effects of the different value of the nonlocal parameters, mean speed value and ratios of fluid mass to the total mass as well as effects of the simple–simple and clamped–clamped boundary conditions on the linear and nonlinear frequencies, stability, frequency–response curves and bifurcation point are presented numerically and graphically. The solvability conditions are obtained for the three distinct cases of velocity fluctuation frequency. For all cases, the stability areas of system are constructed analytically.     

Effects of rotary inertia on sub- and super-critical free vibration of an axially moving beam

The most important issue in the vibration study of an engineering system is dynamics modeling. Axially moving continua is often discussed without the inertia produced by the rotation of the continua section. The main goal of this paper is to discover the effects of rotary inertia on the free vibration characteristics of an axially moving beam in the sub-critical and super-critical regime. Specifically, an integro-partial-differential nonlinear equation is modeled for the transverse vibration of the moving beam based on the generalized Hamilton principle. Then the effects of rotary inertia on the natural frequencies, the critical speed, post-buckling vibration frequencies are presented. Two kinds of boundary conditions are also compared. In super-critical speed range, the straight configuration of the axially moving beam loses its stability. The buckling configurations are derived from the corresponding nonlinear static equilibrium equation. Then the natural frequencies of the post-buckling vibration of the super-critical moving beam are calculated by using local linearization theory. By comparing the critical speed and the vibration frequencies in the sub-critical and super-critical regime, the effects of the inertia moment due to beam section rotation are investigated. Several interesting phenomena are disclosed. For examples, without rotary inertia, the study overestimates the stability of the axially moving beam. Moreover, the relative differences between the super-critical fundamental frequencies of the two theories may increase with an increasing beam length.     

Explicit frequency equations of free vibration of a nonlocal Timoshenko beam with surface effects

Considerations of nonlocal elasticity and surface effects in micro-and nanoscale beams are both important for the accurate prediction of natural frequency. In this study, the governing equation of a nonlocal Timoshenko beam with surface effects is established by taking into account three types of boundary conditions: hinged–hinged, clamped–clamped and clamped–hinged ends. For a hinged–hinged beam, an exact and explicit natural frequency equation is obtained. However, for clamped–clamped and clamped–hinged beams, the solutions of corresponding frequency equations must be determined numerically due to their transcendental nature. Hence, the Fredholm integral equation approach coupled with a curve fitting method is employed to derive the approximate fundamental frequency equations, which can predict the frequency values with high accuracy. In short,explicit frequency equations of the Timoshenko beam for three types of boundary conditions are proposed to exhibit directly the dependence of the natural frequency on the nonlocal elasticity, surface elasticity, residual surface stress, shear deformation and rotatory inertia, avoiding the complicated numerical computation.     

Fractional visco-elastic Euler–Bernoulli beam

Aim of this paper is the response evaluation of fractional visco-elastic Euler–Bernoulli beam under quasi-static and dynamic loads. Starting from the local fractional visco-elastic relationship between axial stress and axial strain, it is shown that bending moment, curvature, shear, and the gradient of curvature involve fractional operators. Solution of particular example problems are studied in detail providing a correct position of mechanical boundary conditions. Moreover, it is shown that, for homogeneous beam both correspondence principles also hold in the case of Euler–Bernoulli beam with fractional constitutive law. Virtual work principle is also derived and applied to some case studies.     

Stability analysis of internally damped rotating composite shafts using a finite element formulation

This paper deals with the stability analysis of internally damped rotating composite shafts. An Euler–Bernoulli shaft finite element formulation based on Equivalent Single Layer Theory (ESLT), including the hysteretic internal damping of composite material and transverse shear effects, is introduced and then used to evaluate the influence of various parameters: stacking sequences, fiber orientations and bearing properties on natural frequencies, critical speeds, and instability thresholds. The obtained results are compared with those available in the literature using different theories. The agreement in the obtained results show that the developed Euler–Bernoulli finite element based on ESLT including hysteretic internal damping and shear transverse effects can be effectively used for the stability analysis of internally damped rotating composite shafts. Furthermore, the results revealed that rotor stability is sensitive to the laminate parameters and to the properties of the bearings.     

Axial-flexural coupled vibration and buckling of composite beams using sinusoidal shear deformation theory

A finite element model based on sinusoidal shear deformation theory is developed to study vibration and buckling analysis of composite beams with arbitrary lay-ups. This theory satisfies the zero traction boundary conditions on the top and bottom surfaces of beam without using shear correction factors. Besides, it has strong similarity with Euler–Bernoulli beam theory in some aspects such as governing equations, boundary conditions, and stress resultant expressions. By using Hamilton’s principle, governing equations of motion are derived. A displacement-based one-dimensional finite element model is developed to solve the problem. Numerical results for cross-ply and angle-ply composite beams are obtained as special cases and are compared with other solutions available in the literature. A variety of parametric studies are conducted to demonstrate the effect of fiber orientation and modulus ratio on the natural frequencies, critical buckling loads, and load-frequency curves as well as corresponding mode shapes of composite beams.     

Correction of local elasticity for nonlocal residuals: application to Euler–Bernoulli beams

Complications exist when solving the field equation in the nonlocal field. This has been attributed to the complexity of deriving explicit forms of the nonlocal boundary conditions. Thus, the paradoxes in the existing solutions of the nonlocal field equation have been revealed in recent studies. In the present study, a new methodology is proposed to easily determine the elastic nonlocal fields from their local counterparts without solving the field equation. This methodology depends on the iterative-nonlocal residual approach in which the sum of the nonlocal fields is treaded as a residual field. Thus, in this study the corrections of the local linear and nonlinear elastic fields for the nonlocal residuals in materials are presented. These corrections are formed based on the general nonlocal theory. In the context of the general nonlocal theory, two distinct nonlocal parameters are introduced to form the constitutive equations of isotropic elastic continua. In this study, it is demonstrated that the general nonlocal theory outperforms Eringen’s nonlocal theory in accounting for the impacts of the material’s Poisson’s ratio on its mechanics. To demonstrate the effectiveness of the proposed approach, the corrections of the local static bending, vibration, and buckling characteristics of Euler–Bernoulli beams are derived. Via these corrections, bending, vibration, and buckling behaviors of simple-supported nonlocal Euler–Bernoulli beams are determined without solving the beam’s equation of motion.     

On the plastic buckling of curved carbon nanotubes

This research, for the first time, predicts theoretically static stability response of a curved carbon nanotube(CCNT) under an elastoplastic behavior with several boundary conditions. The CCNT is exposed to axial compressive loads. The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy.The elastoplastic stress-strain is concerned with Ramberg–Osgood law on the basis of deformation and flow theories of plasticity. To seize the nano-mechanical behavior of the CCNT, the nonlocal strain gradient elasticity theory is taken into account. The obtained differential equations are solved using the Rayleigh–Ritz method based on a new admissible shape function which is able to analyze stability problems. To authorize the solution, some comparisons are illustrated which show a very good agreement with the published works. Conclusively, the best findings confirm that a plastic analysis is crucial in predicting the mechanical strength of CCNTs.     

Modelling a micro-cantilever vibrating in vacuum,gas or liquid under thermal base excitation

The dynamic behaviour of a micro-cantilever that is transversely excited at its base is investigated in this paper. The base actuation is provided by thermal cycles via taking the advantage of thermal expansion. The Euler–Bernoulli equation along with corresponding boundary conditions is used to model the continuous cantilever beam. The resultant boundary value problem takes into account the thermal expansion and stiffness of the actuator at the base as well as the effect of the surrounding gas or liquid. A closed-form analytical model is developed to compute natural frequencies, mode shapes, and harmonic response of the vibrating cantilever, in addition to an integral function for quality factor. The model is validated via a finite element (FE) analysis using ANSYS commercial package. This validation shows that the proposed model can properly predict the cantilever's vibrating behaviour.     

Analytical solutions for thermal vibration of nanobeams with elastic boundary conditions

A nonlocal Euler beam model with second-order gradient of stress taken into consideration is used to study the thermal vibration of nanobeams with elastic boundary.An analytical solution is proposed to investigate the free vibration of nonlocal Euler beams subjected to axial thermal stress.The effects of the nonlocal parameter,thermal stress and stiffness of boundary constraint on the vibration behaviors of nanobeams are revealed.The results show that natural frequencies including the thermal stress are lower than those without the thermal stress when temperature rises.The boundary-constrained springs have significant effects on the vibration of nanobeams.In addition,numerical simulations also indicate the importance of small-scale effect on the vibration of nanobeams.     

基于应变梯度中厚板单元的石墨烯振动研究

基于应变梯度理论建立了单层石墨烯等效明德林(Mindlin) 板动力学方程,推导了四边简支明德林中厚板自由振动固有频率的解析解. 提出了一种考虑应变梯度的4 节点36 自由度明德林板单元,利用虚功原理建立了单层石墨烯的等效非局部板有限元模型. 通过对石墨烯振动问题的研究,验证了应变梯度有限元计算结果的收敛性. 运用该有限元法研究了尺寸、振动模态阶数以及非局部参数对石墨烯振动特性的影响. 研究表明,这种单元能够较好地适用于研究考虑复杂边界条件石墨烯的尺度效应问题. 基于应变梯度理论的明德林板所获得石墨烯的固有频率小于基于经典明德林板理论得到的结果. 尺寸较小、模态阶数较高的石墨烯振动尺度效应更加明显. 无论采用应变梯度理论还是经典弹性本构关系,考虑一阶剪切变形的明德林板模型预测的固有频率低于基尔霍夫(Kirchho) 板所预测的固有频率.      

In-plane bending vibration analysis of a rotating beam with multiple edge cracks by using the transfer matrix method

Meccanica - In this study, the effects of cracks on the natural frequencies of a rotating Bernoulli–Euler beam are investigated using a new numerical method in which these effects can be...     

Free vibration of functionally graded beams based on both classical and first-order shear deformation beam theories

The free vibration of functionally graded material （FGM） beams is studied based on both the classical and the first-order shear deformation beam theories. The equations of motion for the FGM beams are derived by considering the shear deforma- tion and the axial, transversal, rotational, and axial-rotational coupling inertia forces on the assumption that the material properties vary arbitrarily in the thickness direction. By using the numerical shooting method to solve the eigenvalue problem of the coupled ordinary differential equations with different boundary conditions, the natural frequen- cies of the FGM Timoshenko beams are obtained numerically. In a special case of the classical beam theory, a proportional transformation between the natural frequencies of the FGM and the reference homogenous beams is obtained by using the mathematical similarity between the mathematical formulations. This formula provides a simple and useful approach to evaluate the natural frequencies of the FGM beams without dealing with the tension-bending coupling problem. Approximately, this analogous transition can also be extended to predict the frequencies of the FGM Timoshenko beams. The numerical results obtained by the shooting method and those obtained by the analogous transformation are presented to show the effects of the material gradient, the slenderness ratio, and the boundary conditions on the natural frequencies in detail.