Thermal analysis study of flavonoid solid dispersions having enhanced solubility

Purposes of this paper were to prepare and study new drug delivery systems for both flavanone glycosides and their aglycones based on solid-dispersion systems. These compounds are poor water soluble drugs, so an enhancement of their dissolution is a high priority. Solid-dispersion systems were prepared using PVP, PEG and mannitol as drug carrier matrices. Characterizations of these dispersions were done by differential scanning calorimeter (DSC) and X-ray diffraction (XRD). The glass transition (T_g) temperature of PVP was only recorded in the DSC thermograms of PVP solid-dispersions of both flavanone glycosides and their aglycones, while in case of PEG and mannitol solid-dispersions endotherms of both glycosides and aglycones were noticed with low peak intensity, indicating that high percent of drug is in amorphous state. The XRD patterns of all PVP solid-dispersions of aglycones show typical amorphous materials, but XRD patterns of their glycosides reveal the presence of crystalline material. However, in all solid dispersions shifts in T_g of PVP as well as T_m of PEG were observed, indicating the existence of some interactions between drugs and matrices. SEM and TEM microscopy revealed that PVP/aglycone flavanone compounds are nanodispersed systems while all the other solid dispersions are microcrystalline dispersions. The solubility of both flavanone glycosides and their aglycones was directly affected by the new physical state of solid dispersions. Due to the amorphous drug state or nano-dispersions in PVP matrices, the solubility was enhanced and found to be 100% at pH 6.8 in the nano-dispersion containing 20 mass% of aglycones. Also solubility enhancement was occurred in solid dispersions of PEG and mannitol, but it was lower than that of PVP nano-dispersions due to the presence of the drug compounds in crystalline state in both matrices.     

Succinic or glutaric anhydride modified linear unsaturated (epoxy) polyesters

A series of N-alkyl-N-alkyl′-pyrrolidinium-bis(trifluoromethanesulfonyl) imide (TFSI⁻) room temperature ionic liquids (RTILs) has been investigated by means of thermogravimetric analysis (TG), differential scanning calorimetry, FT-IR spectroscopy, and X-ray diffraction analysis. These compounds exhibit a thermal stability up to 548–573 K. The mass loss starting temperature, T _ml, falls in a narrow range of temperatures: 578–594 K. FT-IR spectra, performed before and after 24 h isothermal experiments at 553 and 573 K, have confirmed their great thermal stability. Below the ambient temperature, these compounds exhibit a complex behavior. N-methyl-N-propyl-pyrrolidinium-TFSI is the sole liquid which crystallizes without forming any amorphous phase even after quenching in liquid nitrogen. Its crystalline phase has a melting point, T _m, of 283 ± 1 K. When the amorphous solid is heated, the N-butyl-N-ethyl-pyrrolidinium-TFSI presents a glass transition temperature, T _g, at 186 K followed by a cold crystallization, T _cc, at 225 K, and a final T _m at 262 K. The N-butyl-N-methyl-pyrrolidinium-TFSI exhibits a T _g between 186 and 181 K, its cold crystallization leading to two different solid phases. Solid phase I has a melting point T _I,m = 252 K and phase II, T _II,m = 262 K. When the amorphous phase is obtained at a cooling rate of 10 K/min, its T _cc is 204 K, and a metastable solid phase (III) is obtained which transforms into the phase II at 226 K. However, when the sample is quenched, the amorphous phase transforms into phase II at T _cc = 217 K and phase I at 239 K. P₁₅-TFSI exhibits the most complicated pattern as, on cooling, it leads to both a crystallized phase at 237 K and an amorphous phase at 191 K. On heating, after a T _g at 186 K and a T _cc at 217 K, two solid–solid phase transitions are observed at 239 K and 270 K, the final T _m being 279 K.     

THE EFFECTS OF IRRADIATION ON THE THERMAL PROPERTIES OF SEMI-CRYSTALLINE POLYAMIDES

Irradiation crosslinking of semi-crystalline polyamides was performed by high energy electronswith various dosages. It is known that the melting behavior of the polymers after irradiation is acomplex phenomenon. In company with the wide angle X-ray diffraction and DSC data of irradiatedand unirradiated polyamides it is possible to develop the local order and perfection of the crystallinitiesslightly which resulted from introduction of intermolecular crosslinking in amorphous region, incl-uding in amorphous-crystalline interface and crystalline defect regions due to irradiation. It canbe explained that slight increase of melting temperature (T_m) and heat of fusion (△H_f) with increasingdosage for both of higher crystallinity nylon 4 and nylon 6. For irradiated lower crystallinity nylons,in contrast, the T_m and △H_f decrease obviously with increasing dosage. In this case, radiation cross-linking "freeze in" the pre-existing morphology, and then the prevention for reorganization duringheating is a dominant effect. The T_m from the second melting for all of the samples were depressed,corresponding with Flory theory. Therefore the crosslinks imposed on the molecules restrainedthe molecular mobility, and that not only depresses the crystallinity but also increases the imperfec-tion of crystallites when the radiated polymer melted and then recrystallized. These are also reflectedin the depression of heat and entropy of fusion as well as the appearance of double melting peakson the DSC thermograms.     

Standard enthalpy of formation of 3,4,5-trimethoxybenzoic acid

The energy of combustion of crystalline 3,4,5-trimethoxybenzoic acid in oxygen at T=298.15 K was determined to be -4795.9±1.3 kJ mol^-1 using combustion calorimetry. The derived standard molar enthalpies of formation of 3,4,5-trimethoxybenzoic acid in crystalline and gaseous states at T=298.15 K, Δ_fH_m ^Θ (cr) and Δ_fH_m ^Θ (g), were -852.9±1.9 and -721.7±2.0 kJ mol^-1, respectively. The reliability of the results obtained was commented upon and compared with literature values. This revised version was published online in August 2006 with corrections to the Cover Date.     

Solidification of molten zinc chloride

Solidification of molten zinc chloride was studied both experimentally and theoretically. By isothermal thermal analysis the time needed for the melt to crystallize at a given temperature ranging between 453 and 553 K was determined and the data obtained were compared with those of a calculated TTT curve. The extremum coordinates (temperature T _N, time t _N) of the curve, critical cooling rate v _CR, interfacial energy σ, and an additional parameter of kinetics barrier for nucleation ɛ were determined as T _N=508 K, t _N=7.29 s, v _CR=11.38 K s⁻¹, σ=0.11956 J m⁻² and ɛ=0.5712. By non-isothermal method the critical cooling rate of glass formation was determined as 1.25 K s⁻¹.     

Nimesulide/cyclodextrin/PEG 6000 ternary complexes: physico-chemical characterization, dissolution studies and bioavailability in rats

Purpose Ternary solid dispersions were prepared in order to estimate the effect of a double hydrophilization by cyclodextrins and PEG 6000 on nimesulide apparent characteristics. Ternary solid dispersions of nimesulide, cyclodextrins and PEG 6000 were characterized using DSC, FT-IR, dissolution studies and evaluating the bioavailability in rats. Methods Ternary solid dispersions were prepared either using native powders or using a preformed inclusion complex of nimesulide and cyclodextrin. Inclusion complexes and pure drug were used as references. Circulating nimesulide was measured out in rat plasma after orally administration of our different products (ternary solid dispersions, inclusion complexes and pure drug). Results An improvement of the nimesulide dissolution rate was obtained with inclusion complexes and ternary solid dispersion. In rat plasma, inclusion complexes and ternary solid dispersion improved T _max. Conclusions A second hydrophilization of inclusion complexes by PEG 6000 does not allow to achieve better results concerning nimesulide concentration in rat plasma or in dissolution studies than with inclusion complexes alone.     

Alternating-current ionic conduction and dielectric relaxation of poly(vinylidene fluoride) at high temperatures

Dielectric properties of poly(vinylidene fluoride) have been studied in the frequency range 20 Hz to 1 MHz and between 100 and 220°C, during heating and cooling. The dielectric constant and loss change abruptly at the temperature T_m corresponding to the melting point. At lower frequencies, two types of ionic conductin are observed. One appears below T_m and is attributed to interfacial polarization. The other occurs above T_m and is related to electrode polarization. These results suggest that a crystalline polymer is a heterogeneous medium for ionic transport, while the melt is a homogeneous medium. From these results, the nature of ac ionic conduction in crystalline polymers is discussed. At high frequency, the α relaxation is observed below T_m. It is due to the molecular motion in the crystalline region and disappears at T_m.     

Thermal properties of post-consumer PET processed in presence of phosphites

Thermal properties of recycled triphenylphosphite (TPP) chain extended poly(ethylene terephthalate) (PET) was investigated. As the TPP concentration increases, both reaction residues and molecular mass increase affecting significantly the thermal properties and crystallization behavior of the material. The presence of TPP residues did not affect the crystalline melt temperature (T _m), but modified the glass transition temperature (T _g), the crystallization temperature on heating (T _hc) and the crystallization temperature on cooling (T _cc). In the samples submitted to extraction with acetone, the properties were influenced by molecular mass changes, probably due to the presence of some insoluble reaction residue. The thermal stability of the sample purified by extraction after chain extension was comparable to that of the non-extended sample when heating was carried out under nitrogen atmosphere.This revised version was published online in November 2005 with corrections to the Cover Date.     

Reversible Transformation between Amorphous and Crystalline States of Unsaturated Polyesters by Cis–Trans Isomerization

An aliphatic polyester has been prepared from ethylene oxide and maleic anhydride that undergoes reversible transformation between amorphous (T_g=18 °C) and crystalline (T_m=124 °C) states through cis–trans isomerization of the C=C bonds in the polymer backbone without any change in either the molecular weight or dispersity of the polymer. A similar transformation was also observed in chiral unsaturated polyesters formed from enantiopure terminal epoxides, such as epichlorohydrin, phenyl glycidyl ether, and (2,3‐epoxypropyl)benzene. These unsaturated polyesters with 100 % E‐configuration in the crystalline state were prepared by quantitative isomerization of their Z‐configuration analogues in the presence of a catalytic amount of diethylamine, while in the presence of benzophenone, irradiation with 365 nm UV light resulted in the transformation of about 30 % trans‐alkene to cis‐maleate form, thereby affording amorphous polyesters.     

Studies of miscibility,transesterification and crystallization in blends of poly(ethylene terephthalate) and Poly(ethylene-2,6-naphthalene dicarboxylate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene-2,6-naphthalene dicarboxylate) (PEN) were obtained by coprecipitation from solution followed by melt-pressing for different timest _mand quenching in iced water. When the melt-pressing time was 0.2 and 0.5 min, two glass transition temperaturesT _gwere observed by means of dynamic mechanical analysis (DMA), indicating that there are two phases present, a PEN-rich phase and a PET-rich phase. The differential scanning calorimetry (DSC) curves show two crystallization peaks and two melting peaks which, according to wide-angle x-ray scattering (WAXS) measurements, can be attributed to PET and PEN, respectively. In the case oft _m=2 min or longer, a single value ofT _gand thus a single phase is found to exist. Fort _m=10 min and 45 min no crystallization and melting at all is observed during heating with 10°C/min, indicating that a copolyester of PET and PEN has been formed by transesterfication during melt-pressing.Time-resolved WAXS measurements during isothermal crystallization show that, in the blend, the half-time of crystallization of PET is different from that of PEN, and not the same as that which is found in the pure polymer.Dedicated with best wishes to Prof. Dr. E.W. Fischer on the occasion of his 65th birthday     

Synthesis and Characterization of Polymides Containing Oxyalkylene Linkages

As part of a program on impact/solvent resistant structural resins for potential use on commercial airplanes, a series of new polyimides containing flexibilizing ethylenedioxy units was prepared. These materials were synthesized by the reaction of aromatic dianhydrides such as 3,3′, 4,4′-benzophenonetetracarboxylic dianhydride (BTDA) with diamines containing ethylene-dioxy linkages such as bis [2-(3-aminophenoxy)ethyl] ether (BAEE). The glass transition temperature (T_g ) and crystalline melting temperature (T_m ) of these polymers varied from 155 to 246°C and 236 to 460°C, respectively. Work concentrated on the polymer from BTDA and BAEE which had a T_g of 155°C and a T_m of 236°C. This polymer has been shown to be an excellent adhesive. For example, titanium-to-titanium tensile shear specimens were evaluated under a variety of test conditions and gave 25°C values of 54 MPa and 93°C values of 38 MPa. This polyimide also exhibited good resistance to hydraulic fluid but crazed upon exposure to paint stripper. Recent work has focused on the development of soluble systems that can be annealed into crystalline states. Thus, the polyimide prepared from BTDA and bis [2-(3-methyl-4-aminophenoxy)ethyl] ether can be obtained in a highly soluble amorphous form that undergoes crystallization upon heating.     

Crystallization of micelles and matrix in dilute diblock copolymer/homopolymer solutions

The crystallization, morphology, and crystalline structure of dilute solid solutions of tetrahydrofuran–methyl methacrylate diblock copolymer (PTHF-b-PMMA) in poly(ethylene oxide) (PEO) and PTHF have been studied with differential scanning calorimetry (DSC), X-ray, and optical microscopy. This study provides a new insight into the crystallization behavior of block copolymers. For the dilute PTHF-b-PMMA/PEO system containing only 2 to 7 wt % of PTHF content, crystallization of the PTHF micellar core was detected both on cooling and on heating. Compared the crystallization of the PTHF in the dilute solutions with that in the pure copolymer, it was found that the crystallizability of the PTHF micellar core in the solution is much greater than that of the dispersed PTHF microdomain in the pure copolymer. The stronger crystallizability in the solution was presumably due to a softened PMMA corona formed in the solution of the copolymer with PEO. However, the “soft” micelles formed in the solution (meaning that the glass transition temperatures (T_g) of the micelle is lower than the T_m of the matrix phase) showed almost no effects on the spherulitic morphology of the PEO component, compared with that of the pure PEO sample. In contrast, significant effects of the micelles with a “hard” PMMA core (meaning that the T_g of the core is higher than the T_m of the PTHF homopolymer) on the nucleation, crystalline structure, and spherulitic morphology were observed for the dilute PTHF-b-PMMA/PTHF system. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2961–2970, 1998     

Low surface energy polymers and surface-active block polymers. III. Adamantyl-containing polymers

Two adamantyl-containing oxazoline monomers. 2-(1-adamantyl)-2-oxazoline, A , and 2-(1-adamantylmethyl)-2-oxazoline, B , were synthesized, and polymerized in 1,2-dichlorobenzene to give polymers PA and PB respectively. Both polymers are highly crystalline and showed very high T_m's (269°C for PA and 320°C for PB ) and little solubility in common organic solvents. Annealed PA showed a critical surface tension of 23.6 dyne/cm. PB was not soluble in the many organic solvents tested at room temperature. Due to its high T_m and insolubility, contact angle measurements on PB were impossible. Diblock copolymers based on different weight ratios of A and 2-ethyl-2-oxazoline, E , showed relatively narrow molecular weight distribution (MWD) when methyl p-nitrobenzenesulfonate, I , was used as initiator. After annealing, diblock polymers with B/I = 7, 10, or 12 showed T_m's (200–281°C); after quenching the same samples showed T_c's (160–171°C), which were lower than that of pure PB , 215°C. The quenched diblocks showed single T_g's (63–82°C) which implies that these short blocks are compatible. Diblock polymer with B/I = 5 and E/I = 20 was amorphous and displayed inverse emulsifying ability in styrene + water emulsion polymerization. BEB type triblock polymers prepared using ethylene glycol dinosylate as initiator had broader MWD and higher T_m's compared to their diblock counterparts with the same B/E wt% and B/I ratios. These triblock polymers were not completely soluble in styrene and/or water and therefore could not be used as emulsifying agents.     

Thermodynamic and kinetic behaviour of salicylsalicylic acid

The thermal behaviour of salicylsalicylic acid (CAS number 552-94-3) was studied by differential scanning calorimetry (DSC). The endothermic melting peak and the fingerprint of the glass transition were characterised at a heating rate of 10°C min^-1. The melting peak showed an onset at T _on = 144°C (417 K) and a maximum intensity at T _max = 152°C (425 K), while the onset of the glass transition signal was at T _on = 6°C. The melting enthalpy was found to be Δ_mH = 28.9±0.3 kJ mol^-1, and the heat capacity jump at the glass transition was ΔC _P = 108.1±0.1 J K^-1mol^-1. The study of the influence of the heating rate on the temperature location of the glass transition signal by DSC, allowed the determination of the activation energy at the glass transition temperature (245 kJ mol^-1), and the calculation of the fragility index of salicyl salicylate (m = 45). Finally, the standard molar enthalpy of formation of crystalline monoclinic salicylsalicylic acid at T = 298.15 K, was determined as Δ_fH_m ^o(C₁₄H₁₀O₅, cr) = - (837.6±3.3) kJ mol^-1, by combustion calorimetry. This revised version was published online in August 2006 with corrections to the Cover Date.     

Calorimetric study and thermal analysis of crystalline nicotinic acid

As one primary component of Vitamin B₃, nicotinic acid [pyridine 3-carboxylic acid] was synthesized, and calorimetric study and thermal analysis for this compound were performed. The low-temperature heat capacity of nicotinic acid was measured with a precise automated adiabatic calorimeter over the temperature rang from 79 to 368 K. No thermal anomaly or phase transition was observed in this temperature range. A solid-to-solid transition at T _trs=451.4 K, a solid-to-liquid transition at T _fus=509.1 K and a thermal decomposition at T _d=538.8 K were found through the DSC and TG-DTG techniques. The molar enthalpies of these transitions were determined to be Δ_trs H _m=0.81 kJ mol^-1, Δ_fus H _m=27.57 kJ mol^-1 and Δ_d H _m=62.38 kJ mol^-1, respectively, by the integrals of the peak areas of the DSC curves. This revised version was published online in August 2006 with corrections to the Cover Date.     

Molar heat capacity and thermodynamic properties of 1,2-cyclohexane dicarboxylic anhydride [C8H10O3]

The molar heat capacity C _p,m of 1,2-cyclohexane dicarboxylic anhydride was measured in the temperature range from T=80 to 390 K with a small sample automated adiabatic calorimeter. The melting point T _m, the molar enthalpy Δ_fus H _m and the entropy Δ_fus S _m of fusion for the compound were determined to be 303.80 K, 14.71 kJ mol⁻¹ and 48.43 J K⁻¹ mol⁻¹, respectively. The thermodynamic functions [H _T-H _273.15] and [S _T-S _273.15] were derived in the temperature range from T=80 to 385 K with temperature interval of 5 K. The thermal stability of the compound was investigated by differential scanning calorimeter (DSC) and thermogravimetry (TG), when the process of the mass-loss was due to the evaporation, instead of its thermal decomposition.     

Polyamides from trans-4-octen-1,8-dioic and trans-2-trans-6-octadien-1,8-dioic acids

Novel polyamides from trans-4-octen-1,8-dioic acid (4-OD) and trans-2-trans-6-octadien-1,8-dioic acid (2,6-ODD) ad linear aliphatic diamines or piperazine were prepared in good yields by low-temperature polycondensation. The polymers obtained were investigated by infrared spectroscopy, x-ray diffraction, and differential scanning calorimetry. Polyamides from 4-OD show high molecular weights and crystallinities and T_m above 500°K, whereas those from 2,6-ODD are very weakly crystalline and decompose without melting in nitrogen at temperatures higher than 550°K. DSC studies revealed in the case of 4-OD polymers with odd diamines, a multiple peak phenomenon in the melting region, strongly dependent from the heating rate. Some hypotheses consistent with this behavior are briefly discussed, and it is concluded that the phenomenon arises from melt recrystallization occurring during the DSC scan.     

Structural and thermodynamic features of the polyhydroxybutyrate physical gels

The structural and thermal properties of polyhydroxybutyrate (PHB) gels in dimethylformamide (DMF) are presented and discussed. The dilute and semi-dilute mixed PHB/DMF system undergoes a phase separation on cooling at a temperature T_gel, producing a gel in which the crystalline fraction is of the order of 50-60% and the diffraction pattern is that of disperse nano-crystals, with the same unit cell of the pure crystalline PHB. Upon heating, two melting peaks are normally observed at T_m1 and T_m2 (always higher than T_gel). Shapes of the peaks, temperatures and enthalpies of melting depend slightly on scanning rate on heating but on the procedure of gel preparation. Reproducibility and reversibility have always been found with repeated thermal cycles. A thermodynamic phase diagram is therefore constructed and discussed, although the morphology of the system may be subject to the experimental conditions under which the gel is prepared.     

Influence of alkyl tail length on self-organisation of side-chain liquid crystalline polymers with biphenyl hemiphasmidic mesogens

A new and simple series of side-chain liquid crystalline polymethacrylates containing biphenyl hemiphasmidic mesogens based on 4-[(3,4,5-trialkan)-1-carbonylbenzoate]biphenyl (denoted as PT_mBMA, m = 6, 8, 10, 12, 14, 16, 18, m refers to the carbon number of alkoxy tails) groups was designed and successfully synthesised via free radical polymerisation. The phase structures and transitions of the polymers were investigated by the combination of techniques including differential scanning calorimetry, polarizing microscope, one-dimensional/two-dimensional wide-angle X-ray diffraction, and small-angle X-ray scattering. The experimental results revealed that the liquid crystalline phase structures and behaviours of the polymers were found to be strongly dependent on the alkyl tail length (m). When m = 6, the PT_mBMA formed a stable smectic phase above T_g. When m = 8, 10, 12, 14, 16, 18, the sample presented a hexagonal columnar mesophase (Φ_h), suggesting that the alkyl length has played an important role in the phase behaviours of hemiphasmidic side-chain liquid crystalline polymers.     

Ambient temperature thermotropic liquid crystalline viologen bis(triflimide) salts

Two dicationic salts with bis(triflimide) as counterions exhibited crystal-to-smectic liquid crystalline phase transitions (T _m=41 and 37°C) and smectic-to-isotropic liquid phase transitions (T _i=112, 136°C). They had a broad liquid crystalline phase range (71–99°C) and an excellent range of thermal stability (360–364°C). Their mixtures of various compositions also displayed liquid crystalline properties from r.t. to an extended range of temperatures. They exhibited fluorescence in 1, 2-dimethoxyethane and methanol.