Investigation of Shock Wave Loading and Crater Creation by Means of Single and Double Targets in the PALS-Laser Experiment

The efficiency of crater creation for different types of Al targets, namely, single massive targets and double targets consisting of a foil or a disk placed before the massive target at a chosen distance (300 and 500 µm), is studied. Targets were irradiated by the PALS facility laser beam with E _L = 100 – 400 J at the first harmonic λ = 1315 nm, a focal spot radius of 125 µm, and pulse duration of 400 ps. Velocities of the accelerated foil’s fragments or disks and electron density distributions of the plasma streams are determined by means of three-frame interferometry. Shapes and volumes of craters are obtained using the crater replica technology and microscopy measurements. It is shown that direct laser action is the most efficient way of energy transfer to the massive target and the most efficient method of crater creation. Somewhat lower efficiencies of shock wave loading and crater creation in comparison with direct laser action are found in the case of double targets where the energy is transferred to the massive target by colliding laser-driven foils or disks. The efficiencies of such a colliding energy transfer are close to 60% for foils and 40% for disks. The experimental results are in a good agreement with two-dimensional hydrodynamic models of shock wave generation under direct laser action and laser-driven macroparticle impact.     

Optimization of EUV radiation yield from laser-produced plasma

We optimize the conversion of laser energy into extreme ultraviolet (EUV) radiation by tailoring the laser parameters for a laser-produced plasma generated from 20 μm diameter water droplets. It is shown that mass-limited targets require careful adaption of laser-pulse energy and laser-pulse duration separately, rather than laser intensity, which seems to be adequate for bulk targets. The optimal pulse duration scales with the droplet radius, and the optimal pulse energy with the droplet volume. With optimized parameters, we obtain a conversion efficiency of 0.23% in 4π and 2.5% bandwidth for 13 nm radiation, the future EUV lithography light. Received: 16 July 2001 / Revised version: 25 September 2001 / Published online: 7 November 2001     

Table-top kHz hard X-ray source with ultrashort pulse duration for time-resolved X-ray diffraction

The interaction of ultrashort laser pulses with solid state targets is studied concerning the production of short X-ray pulses with photon energies up to about 10 keV. The influence of various parameters such as pulse energy, repetition rate of the laser system, focusing conditions, the application of prepulses, and the chirp of the laser pulses on the efficiency of this highly nonlinear process is examined. In order to increase the X-ray flux, the laser pulse energy is increased by a 2nd multipass amplifier from 750 μJ to 5 mJ. By applying up to 4 mJ of the pulse energy a X-ray flux of 4×10¹⁰ Fe K _α photons/s or 2.75×10¹⁰ Cu K _α photons/s are generated. The energy conversion efficiency is therefore calculated to η _Fe≈1.4×10⁻⁵ and η _Cu≈1.0×10⁻⁵. The X-ray source size is determined to 15×25 μm². By focusing the produced X-rays using a toroidally bent crystal a quasi-monochromatic X-ray point source with a diameter of 56 μm×70μm is produced containing ≈10⁴ Fe K _α1 photons/s which permits the investigation of lattice dynamics on a picosecond or even sub-picosecond time scale. The lattice movement of a GaAs(111) crystal is shown as a typical application.     

Hard tissue ablation with a free running Er:YAG and a Q-switched CO2 laser: a comparative study

The Er:YAG and the CO₂ laser are competitors in the field of hard tissue ablation. The use of Er:YAG lasers (2.94 μm, pulse length _L of 100 to 200 μs) show smaller areas of thermal defects then ‘‘superpulsed’’ CO₂ lasers with pulse lengths of approximately 100 μs. Only the development of a Q-switched CO₂ laser (9.6 μm, τ_L=250 ns) allowed for similar results. In this paper new results for the Er:YAG and the Q-switched CO₂ laser under the influence of water spray will be presented. Several parameters are of special interest for these investigations: the specific ablation energy, which shows a minimum for the CO₂ laser at an energy density of 9 J/cm ² and a broad shallow minimum in the range of 10 to 70 J/cm² for the Er:YAG laser, and comparison of the cut-shape and depth. Surface effects and cutting velocity are discussed based on SEM pictures. Received: 19 July 2000 / Revised version: 1 November 2000 / Published online: 30 November 2000     

The excitation mechanism of rare-earth ions in silicon nanocrystals

A detailed investigation on the excitation mechanisms of rare-earth (RE) ions introduced in Si nanocrystals (nc) is reported. Silicon nanocrystals were produced by high-dose 80-keV Si implantation in thermally grown SiO₂ followed by 1100 °C annealing for 1 h. Subsequently some of the samples were implanted by 300-keV Er, Yb, Nd, or Tm at doses in the range 2×10¹²–3×10¹⁵ /cm². The energy was chosen in such a way to locate the RE ions at the same depth where nanocrystals are. Finally an annealing at 900 °C for 5 min was performed in order to eliminate the implantation damage. These samples show intense room-temperature luminescence due to internal 4f shell transitions within the RE ions. For instance, luminescence at 1.54 μm and 0.98 μm is observed in Er-doped nc, at 0.98 μm in Yb-doped nc, at 0.92 μm in nc and two lines at 0.78 μm and 1.65 μm in Tm-doped nc. Furthermore, these signals are much more intense than those observed when RE ions are introduced in pure SiO₂ in the absence of nanocrystals, demonstrating the important role of nanocrystals in efficiently exciting the REs. It is shown that the intense nc-related luminescence at around 0.85 μm decreases with increasing RE concentration and the energy is preferentially transferred from excitons in the nc to the RE ions which, subsequently, emit radiatively. The exact mechanism of energy transfer has been studied in detail by excitation spectroscopy measurements and time-resolved photoluminescence. On the basis of the obtained results a plausible phenomenological model for the energy transfer mechanism emerges. The pumping laser generates excitons within the Si nanocrystals. Excitons confined in the nc can either give their energy to an intrinsic luminescent center emitting at around 0.85 μm nor pass this energy to the RE 4f shell, thus exciting the ion. The shape of the luminescence spectra suggests that excited rare-earth ions are not incorporated within the nanocrystals and the energy is transferred at a distance while they are embedded within SiO₂. Rare-earth excitation can quantitatively be described by an effective cross section σ_eff taking into account all the intermediate steps leading to excitation. We have directly measured σ_eff for Er in Si nc obtaining a value of ≈2×10⁻¹⁷ cm². This value is much higher than the cross section for excitation through direct photon absorption (8×10⁻²¹ cm²) demonstrating that this process is extremely efficient. Furthermore, the non-radiative decay processes typically limiting rare-earth luminescence in Si (namely back-transfer and Auger) are demonstrated to be absent in Si nc further improving the overall efficiency of the process. These data are reported and their implications. Received: 9 April 1999 / Accepted: 10 April 1999 / Published online: 2 June 1999     

Micro-lens arrays generated by UV laser irradiation of doped PMMA

Micro-lenses with well-defined optical parameters are generated on polymethylmethacrylate (PMMA) substrates doped with diphenyltriazene (DPT) by controlled use of a swelling effect generated under conditions of subablative excimer laser illumination. The surface profiles depend on the laser spot size and energy density. A sensitively balanced combination of matrix softening, substrate volume expansion due to photochemical nitrogen release, and surface tension is responsible for the final shape of the lenses. Complete arrays of identical lenses with 15 μm diameters and a focal length of 30 μm are produced by irradiation of (0.25 wt. %) DPT-PMMA with a single laser pulse at a wavelength of 308 nm and a fluence of 3 J/cm². It is shown experimentally and theoretically that appropriate volume expansion is possible without introducing internal light scattering due to the formation of small bubbles. Received: 7 April 1999 / Accepted: 8 April 1999 / Published online: 5 May 1999     

Laser ablation and micropatterning of thin TiN coatings

Laser ablation of thin TiN films deposited on steel substrates has been studied under wide-range variation of irradiation conditions (pulsewidth, wavelength, energy density and spot size). It has been demonstrated that both picosecond (150–300 ps) and nanosecond (5–9 ns) laser pulses were suitable for controllable ablation and microstructuring of a 1-μm-thick TiN film unlike longer 150-ns pulses. The ablation rate was found to be practically independent of the wavelength (270–1078 nm) and pulsewidth (150 ps–9 ns), but it increased substantially when the size of a laser spot was reduced from 15–60 μm to 3 μm. The laser ablation technique was applied to produce microstructures in the thin TiN films consisting of microcraters with a typical size of 3–5 μm in diameter and depth less than 1 μm. Tests of lubricated sliding of the laser-structured TiN films against a steel ball showed that the durability of lubricated sliding increased by 25% as compared to that of the original TiN film. Received: 28 July 1999 / Accepted: 17 April 2000 / Published online: 20 September 2000     

Antireflection structures written by excimer laser on CVD diamond

Two-dimensional antireflective periodical microstructures for the IR range are fabricated on the surface of CVD diamond films. These structures are created using an ArF excimer laser (λ=193 nm) and a direct writing scheme consisting of a beam collimator and a microscope objective to focus the beam onto the sample. Two different arrays are investigated. One has a spacing of 3 μm and is produced with single shots and the other one has a spacing of 4 μm and is produced with three shots per spot. The hole depth and shape are measured with an atomic force microscope (AFM). The optical transmittance and the scattering properties of the structure at 10.6 μm are reported for a CO₂ laser beam. With a spectrometer further transmission measurements in the range of 5 to 20 μm are performed. Received: 16 September 1999 / Accepted: 11 October 1999 / Published online: 24 March 2000     

New short-wavelength laser emissions from partially deuterated methanol isotopes

The partially deuterated isotopes of methanol, CH₂DOH and CHD₂OH, have been reinvestigated as sources of far-infrared (FIR) laser emissions using an optically pumped molecular laser (OPML) system recently designed for wavelengths below 150 μm. With this system, 10 new FIR laser emissions from these isotopes ranging from 32.8 to 174.6 μm have been discovered. This includes the shortest known OPML emission from CHD₂OH, at 32.8 μm. These lines are reported with their operating pressure, polarizations relative to the CO₂ pump laser and wavelengths, measured to ±0.5 μm. In addition, polarizations for three previously observed FIR laser lines from CHD₂OH were measured for the first time. This paper is dedicated to the memory of Dr. K.M. Evenson, a pioneer in the field for his role in the development of optically pumped molecular lasers and their use in laser frequency measurements and the laser magnetic resonance technique. His scientific expertise, guidance, mentoring and friendship will be greatly missed. Received: 27 March 2002 / Published online: 8 May 2002     

Stimulated rotational Raman scattering at multiwavelength under tea CO2 laser pumping with a multiple-pass cell

Stimulated rotational Raman scattering (SRRS) at multiwavelength pumped by TEA CO₂ laser was demonstrated in this paper. Raman mediums were cooled by liquid-N₂ and a multiple-pass cell (MPC) with 25 passes was designed and used. When the para-H2 was pumped by single-longitudinal-mode (SLM) circular polarized TEA CO₂ laser on 10P(20), 9P(20), and 10R(20), 50 mJ 16.95 μm, 350 mJ 14.44 μm, and 536 mJ 16.9 μm radiations were obtained, corresponding to energy conversion efficiency of 1.2, 11.7, and 13.4%, respectively. When the ortho-D₂ was pumped by CO₂ laser on 10R(18), 108 mJ 12.57 μm Raman laser was obtained with energy conversion efficiency of 2.9%.     

A Raman laser system for multi-wavelength satellite laser ranging

~~A Raman laser system for multi-wavelength satellite laser ranging@K.Hamal$Czech Technical University in Prague,Czech @I.Prochazka$Czech Technical University in Prague,Czech @J.Blazej$Czech Technical University in Prague,Czech1. Yang Fumin, Chen Wanzhen, Zhang Zhongping et al., Satellite laser ranging experiment with sub-centimeter single-shot ranging precision at Shanghai Observatory, Science in China, Ser. A, 2002, 32(10): 935-939. 2. Degnan, J. J., Millimeter accurac…     

A cw room-temperature Ho,Tm:YLF laser pumped at 1.682 μm

We present the results obtained with a Ho,Tm:YLF crystal grown at a new crystal growth facility in Pisa. The optical quality of the sample has been tested by studying its performance as the active medium of a laser operating at 2.06 μm. We employed three different pump laser sources: a Ti:sapphire, a diode (both tuned at 793 nm) and, for the first time, a continuous-wave Co:MgF₂ laser, tuned at 1.682 μm. At room temperature the best slope efficiency was 30 % in the case of “red” pumping, and 59 % in the case of “infrared” excitation. The typical lasing threshold is about 100 mW. Received: 14 March 2001 / Revised version: 15 June 2001 / Published online: 19 September 2001     

Towards new lasers in Ti:Er:LiNbO3 waveguides: a study of the excited Er3+ states

Detailed excited state absorption measurements under pumping at 980 nm and 1.5 μm together with conventional absorption and emission spectroscopy is employed to investigate optical transitions of Er³⁺ in Ti:LiNbO₃ channel-waveguides. The experimental data were evaluated using the Judd–Ofelt method giving parameters close to those in the bulk. The good agreement between theoretical prediction and measurements allows us to calculate cross section, lifetimes, and branching ratios. Based on these results we developed and tested a model which is able to predict the conditions for which laser operation at 550 nm and 2.7 μm will be possible under 980 nm pumping. Received: 9 December 1998 / Revised version: 8 January 1999 / Published online: 24 March 1999     

The influence of vibrational excitation on the burning voltage of a pulsed electric discharge in HF laser working media

The burning voltages of an intermediate pressure self-sustained volume discharge (SSVD) in SF₆ and SF₆-C₂H₆ mixtures irradiated by a 10.6 μm pulse TEA CO₂ laser, have been measured on varying the laser fluences over a wide range. The delay between the voltage application and the laser pulse onset is 4 μs, and the laser pulse lasts ∼3 μs. The considerable rise observed in the discharge voltages with increasing absorbed specific laser radiation energy, is due to electron attachment to vibrationally excited molecules of SF₆. Different processes of relaxation of the vibrational energy stored in SF₆ molecules are analyzed and the relevant characteristic times are numerically assessed. The gas heating process owing to vibration-translation energy exchange is qualitatively described in terms of the “thermal explosion”. The relation between the “explosion” and delay times determines the peculiarities of electron attachment to vibrationally excited SF₆ molecules. The burning voltages of a submicrosecond non-irradiated SSVD in the above-mentioned media versus the specific electric energy deposited are also measured. They are compared to those of a laser-illuminated SSVD at commensurable specific laser energy depositions. It is concluded that electron attachment to the discharge-produced vibrationally excited SF₆ molecules is not capable of noticeably affecting the discharge voltages of a submicrosecond non-irradiated SSVD. PACS 42.55 Ks; 52.80     

Mid-infrared trace gas detection using continuous-wave difference frequency generation in periodically poled RbTiOAsO4

A tunable mid-infrared continuous-wave (cw) spectroscopic source in the 3.4–4.5 μm region is reported, based on difference frequency generation (DFG) in a quasi-phase-matched periodically poled RbTiOAsO₄ (PPRTA) crystal, DFG power levels of 10 μW were generated at approximately 4 μm in a 20-mm long PPRTA crystal by mixing two cw single-frequency Ti:Al₂O₃ lasers operating near 713 nm and 871 nm, respectively, using a laser pump power of 300 mW. A quasi-phase-matched infrared wavelength-tuning bandwidth (FWHM) of ∼12 cm^-1 and a temperature tuning rate of 1.02 cm^-1/°C were achieved. Experimental details regarding the feasibility of trace gas detection based on absorption spectroscopy of CO₂ in ambient air using this DFG radiation source are also described. Received: 23 October 2000 / Revised version: 22 January 2001 / Published online: 27 April 2001     

Characterisation of laser-produced tungsten plasma using optical spectroscopy method

This paper describes results of spectroscopic investigation of laser-produced tungsten plasma. The laser intensity on the target surface reached up to 30 GW/cm² depending on the focusing conditions. Optical spectra emitted from plasma plumes which were formed under vacuum conditions in front of the tungsten target due to the interaction of Nd-YAG laser pulses (1.06 μm, 0.5 J), were characterised by means of an optical spectrometer (λ/Δλ= 900) in the wavelength range from 300 to 1100 nm. The spectra were recorded automatically with the use of a CCD detector with exposition time varied from 100 ns to 50 ms. On the basis of WI and WII lines it was possible to estimate electron temperature and electron density which corresponded to the expansion phase of the plasma. T_e and N_e were measured as 1.1 eV and 8×10¹⁶ cm^-3, respectively. The spectra collected by the ion energy analyser showed that the plasma included tungsten ions up to 6+ ion charge. Signals from the ion collector allowed to estimate the average value of ion energy of tungsten as 4.6 keV. Basing on this value the electron temperature corresponding to the initial stage of the plasma formation was estimated to be about 320 eV. Optical microscope investigation showed that laser irradiation caused structural changes on the surface of the target.     

CO2 laser-induced plasma CVD synthesis of diamond

2 laser maintenance of a stationary optical discharge in a gas stream, exhausting over a substrate into the air (laser plasmatron). Nano- and polycrystalline-diamond films were deposited on tungsten substrates from atmospheric-pressure Xe(Ar):H₂:CH₄ gas mixtures at flow rates of 2 ?/min. A 2.5-kW CO₂ laser focused beam produced plasma. The deposition area was about 1 cm² and growth rates were up to 30–50 μm/h. Peculiarities and advantages of laser plasmatrons are discussed. Received: 15 January 1998/Accepted: 16 January 1998     

Diode-pumped passively Q-Switched intracavity OPO with a folded cavity configuration

We present in this report an efficient KTP-based intracavity optical parametric oscillator driven by a diode-pumped Nd:GdVO₄/Cr:YAG passively Q-switched laser. For the first time, a novel folded cavity configuration was employed to set the KTP and Cr:YAG crystals separately at different fundamental beam waists. Based on the ABCD-matrix theory and by taking the thermal lens effect into account, the laser cavity was well optimized to enhance the OPO performance. A diode pump threshold as low as 1.2 W and a maximum signal (1.57 μm) average output power up to 560 mW have been achieved. Efficient energy transfer in the IOPO leads to short pulse duration (1.8–2.6 ns) and high peak power (6.8 kW) output at 1.57 μm. Additionally, the correlation dynamics between the pump laser and the OPO was analyzed in detail.     

Phase transformation during surface ablation of cobalt-cemented tungsten carbide with pulsed UV laser

Surface ablation of cobalt-cemented tungsten carbide hard metal has been carried out in this work using a 308 nm, 20 ns XeCl excimer laser. Surface microphotography and XRD, as well as an electron probe have been used to investigate the transformation of phase and microstructure as a function of the pulse-number of laser shots at a laser fluence of 2.5 J/cm². The experimental results show that the microstructure of cemented tungsten carbide is transformed from the original polygonal grains of size 3 μm to interlaced large, long grains with an increase in the number of laser shots up to 300, and finally to gross grains of size 10 μm with clear grain boundaries after 700 shots of laser irradiation. The crystalline structure of the irradiated area is partly transformed from the original WC to βWC_1-x, then to αW₂C and CW₃, and finally to W crystal. It is suggested that the undulating ‘hill–valley’ morphology may be the result of selective removal of cobalt binder from the surface layer of the hard metal. The formation of non-stoichiometric tungsten carbide may result from the escape of elemental carbon due to accumulated heating of the surface by pulsed laser irradiation. Received: 13 July 2000 / Accepted: 27 October 2000 / Published online: 10 January 2001     

A 9.5-W 82-MHz-repetition-rate picosecond optical parametric generator with cw diode laser injection seeding

We report on an injection-seeded 9.5-W 82-MHz-repetition-rate picosecond optical parametric generator (OPG) based on a 55 mm long crystal of periodically poled lithium niobate (PPLN) with a quasi-phase-matching (QPM) grating period of 29.75 μm. The OPG is excited by a continuously diode pumped mode-locked picosecond Nd:YVO₄ oscillator-amplifier system. The laser system generates 7 ps pulses with a repetition rate of 82.3 MHz and an average power of 24 W. Without injection-seeding the total average output power of the OPG is 8.9 W, which corresponds to an internal conversion efficiency of 50%. The wavelengths of the signal and idler waves were tuned in the range 1.57–1.64 μm and 3.03–3.3 μm, respectively, by changing the crystal temperature from 150 °C to 250 °C. Injection seeding of the OPG at 1.58 μm with 4 mW of single frequency continuous-wave radiation of a distributed-feedback (DFB) diode laser increases the OPG output to 9.5 W (53% conversion efficiency). The injection seeding increases the pulse duration and reduces the spectral bandwidth. When pumped by 10 W of 1.06 μm laser radiation, the duration of the signal pulses increased from 3.6 ps to 5.5 ps while the spectral bandwidth is reduced from 4.5 nm to 0.85 nm. Seeding thus improved the time-bandwidth product from 1.98 to a value of 0.56, much closer to the Fourier limit. Received: 29 April 2002 / Published online: 8 August 2002