Effect of Halide Salts of Alkali Metals on Crystallinity of Poly(vinyl Alcohol) Cryogels

The degree of crystallinity of poly(vinyl alcohol) in cryogels obtained by single freezing at–20°С followed by thawing of 13% aqueous solutions of the polymer bearing dissolved NaCl, KCl, CsCl, KBr, and KI in the concentration of 0.7 mol/kg is determined by attenuated total reflectance Fourier transform IR spectroscopy. It is established that the addition of NaCl, KCl, and CsCl to the poly(vinyl alcohol) solution leads to a substantial increase (by 1.5–1.7 times) in the degree of crystallinity in the cryogel prepared from this solution. The effect of KCl, KBr, and KI on the degree of crystallinity strongly depends on the salt anion. The replacement of the Cl^– anion by the larger Br^– anion reduces dramatically the crystallizing effect of the salt, while the even larger I^– anion, in contrast, reduces rather than increases the degree of crystallinity relative to that of the cryogel without a salt. The effect of the salts on the crystallinity of poly(vinyl alcohol) cryogels is explained by the simultaneous action of two processes. One of them facilitates crystallization and consists in the strengthening of dehydration of poly(vinyl alcohol) owing to competition between the polymer molecules and the salt ions for the liquid water molecules during its freezing. The other process hampers crystallization and is connected with a reduction in the water freezing point under action of the salt ions.     

An attenuation total reflectance fourier transform spectroscopic study of crystallinity in the bulk and on the surface of aqueous and aqueous salt cryogels of poly(vinyl alcohol)

The crystallinity of poly(vinyl alcohol) in the bulk and on the surface of cryogels of this polymer prepared in the form of thick disks from solutions in pure water and in water containing potassium chloride is studied via attenuation total reflectance FTIR spectroscopy. The crystallinity values of the upper and lower surfaces of the samples are found from the attenuation total reflectance IR spectra of these surfaces. To determine the crystallinity in the bulk, a sample is cut in half in the middle of its thickness to measure the spectrum of the cut surface. It is found that, in the bulk of a salt-free cryogel, the content of the crystalline phase of the polymer is significantly higher (by a factor of 1.5) than that on the surface. Addition of a salt increases the degree of crystallinity in the bulk and does not change the crystallinity of the surface. Cryogelation mechanisms explaining the increased crystallinity in the bulk of the cryogel and the crystallizing effect of the salt additive are proposed.     

Reduction of silver ions to silver with polyaniline/poly(vinyl alcohol) cryogels and aerogels

The macroporous conducting polymer cryogels were prepared by the oxidation of aniline hydrochloride in the frozen aqueous solutions of poly(vinyl alcohol) at ? 24 °C. Corresponding polyaniline aerogels supported with poly(vinyl alcohol) have been obtained after thawing of cryogels followed by freeze-drying. Silver was deposited on the composites using the ability of polyaniline to reduce silver ions after the immersion in silver nitrate solutions. Swollen cryogels were coated only on the surface with macroscopic silver particles due to the closed-pore structure in cryogels and limited penetration of silver ions into macropores. The diffusion of silver ions to freeze-dried aerogels was better and further improved by vacuum treatment. Silver microcubes were produced in the pores, the weight fraction of silver in dry composites being typically several per cent, a maximum 13 wt%. The conductivity of the aerogels compressed to pellets depended on the processing and the highest value was 0.27 S cm^?1. The aerogels containing silver were characterized in detail with Raman spectroscopy.     

Crystallization of poly(vinyl alcohol) during solvent removal: Infrared characterization and mathematical modeling

Crystallization of semicrystalline polymer films during drying has a significant effect on the rate of solvent removal. Understanding and controlling the crystallization kinetics is important in controlling residual solvent levels and drying kinetics. The degree of crystallinity of the poly(vinyl alcohol) films during multicomponent drying was investigated using Fourier transform infrared spectroscopy (FTIR). The 1141 cm^?1 band is sensitive to the degree of crystallinity of the polymer and the growth of intensity of this band was monitored as drying progressed. The results from the FTIR studies were comparable to the results obtained from differential scanning calorimetry. Studies were conducted to test the effect of initial solvent composition (water–methanol mixture), drying temperature, and polymer molecular weight on the rate of crystallization and the final crystallinity of the films. An increase in initial methanol composition increased the crystallization rate but did not affect the final degree of crystallinity. An increase in drying temperature and decrease in polymer molecular weight increased the rate of crystallization as well as the final degree of crystallinity. Based on the experimental data, rate constants for crystallization kinetics were extracted from our previously developed model based on free volume theory. The experimental data and the simulation results showed good agreement. The ability of the free volume theory to illustrate the crystallization behavior validated the model and improved its capability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 930–935, 2007     

Effect of alkali halide salt additives on the structure of poly(vinyl alcohol) films cast from aqueous solutions

The molecular structures of poly(vinyl alcohol) films cast from polymer aqueous solutions (1 mol/L) containing 0.1 mol/L of LiCl, NaF, NaCl, KCl, CsCl, KBr, and KI salts are studied via FTIR spectroscopy. The addition of any of these salts except LiCl leads to an increase in the degree of crystallinity of poly(vinyl alcohol) in a film by a factor of 1.3–1.6. In contrast, LiCl significantly decreases the crystallinity of the polymer. It is found that, in the IR spectra of the films containing salt additives, the position of the maximum in the band of the stretching vibrations of OH groups of the polymer is shifted relative to its position in the IR spectra of the films free of salt additives. The magnitude and direction of this band shift depend on the types (anion or cation) and radii of ions comprising salts. The observed effects are interpreted in terms of existing ideas on the interactions of salt ions with the OH groups of water and other hydroxyl-containing molecules.     

Determination of crystallinity of swollen poly(vinyl alcohol) by laser Raman spectroscopy

Laser Raman spectra of atactic poly(vinyl alcohol) (PVA) after heat treatment and/or swelling in water have been obtained. An amorphous Raman band is observed at 1124 cm^?1, while a crystalline Raman band is found at 1147 cm^?1. A new method for crystallinity determination is proposed, in which the amorphous band is used instead of the crystalline band. The method is superior to others for water-swollen PVA samples. Laser Raman spectra of swollen PVA revealed that swelling causes destruction of a major fraction of the crystalline regions and the remaining intact crystalline part increases with increasing temperature of heat treatment.     

Direct Electrochemistry and Electrocatalysis of Hemoglobin Immobilized in a Polymeric Ionic Liquid Film

A polymer film based on polymeric ionic liquid, which was poly(1‐vinyl‐3‐butylimidazolium chloride) (poly(ViBuIm⁺Cl^?)for short), was firstly used as matrix to immobilize hemoglobin (Hb). FTIR and UV‐vis spectra demonstrated that the native structure of Hb was well preserved after entrapped into the polymer film. The Hb immobilized in the poly(ViBuIm⁺Cl^?) film showed a fast direct electron transfer for the Hb‐Fe^III/Fe^II redox couple. Based on the direct electron transfer of the immobilized Hb, polyvinyl alcohol (PVA)/Hb/poly(ViBuIm⁺Cl^?)/GC electrode displayed good sensitivity and wide linear range for the detection of H₂O₂. The linear range of the PVA/Hb/poly(ViBuIm⁺Cl^?)/GC electrode to H₂O₂ is from 3.5 to 224 μM with a limit of detection of 1.17 μM. Such an avenue, which integrated polymeric ionic liquid and redox protein via a simple method, may provide a novel and efficient platform for the fabrication of biosensors, biofuel cells and other bioelectrochemical devices.     

Dispersity and stability of foams obtained from poly(vinyl alcohol) solution and the properties of resulting foamed cryogels

Foams have been generated from aqueous poly(vinyl alcohol) solution by two different methods: dispersion (mechanical) method, i.e., by bubbling a gas through a porous medium into the aqueous poly(vinyl alcohol) solution, and the condensation (chemical) method, i.e., by performing a gas-generating reaction directly in the polymer solution. The effect of the formation method on foam stability and dispersity has been studied. The foam produced by the condensation method of foaming the aqueous poly(vinyl alcohol) solution with nitrogen is more stable and finely dispersed and has a higher expansion ratio than that obtained by bubbling the gas through the polymer solution. Foamed cryogels have been formed by freezing-thawing the foam resulting from the chemical reaction in the polymer solution. The values of the elasticity modulus, melting temperature, and thermal conductivity of the cryogels have been determined.     

Raman spectral study of solid and dissolved poly(vinyl alcohol) and ethylene-vinyl alcohol copolymer

We have measured the Raman spectra of ethylene-vinyl alcohol copolymer (EVOH) and poly(vinyl alcohol) (PVOH). Spectra of 88% hydrolyzed PVOH were examined from the partially crystalline solid, from PVOH dissolved in both H₂O and D₂O, and from films precipitated from these solutions. The spectrum in H₂O differs from that of the starting material by disappearance of sharp bands having Raman shift values of 1146 and 1093 cm^?1, strengthening of a band near 915 cm^?1, decrease in frequency of bands at 480, 1356, and 1441 cm^?1, and increase in frequency of bands at 369, 413, 1023, 1371, and 2910 cm^?1. The spectrum of the film shows partial reversal of these trends. With D₂O as the solvent, the band shifts are slightly different from those listed above and new bands appear. These changes are indicative of loss of crystallinity, change in stereochemistry, and partial deuteration of hydroxyl during dissolution of this PVOH sample at room temperature. © 1994 John Wiley & Sons, Inc.     

Reaction of poly(vinyl alcohol) with superoxide anion

Reaction of pol(vinyl alcohol) (PVA) with superoxide anion was carried out in a dimethyl sulfoxide solution at 40°C under nitrogen and changes in the yield of recovered polymer, molecular weight, and chemical structure were examined. Appreciable decreases in the yield of recovered polymer and molecular weight were observed during the reaction, which indicated that a main chain scission of the polymer had occurred. Residual acetyl groups identified by the absorption peaks at ca. 1720 and 1250 cm^?1 in infrared (IR) spectra were removed rapidly and β-diketone groups identified by the peaks at ca. 1640 and 1560 cm^?1 in IR spectra and at ca. 255 nm in ultraviolet (UV) spectra were formed during the reaction. Formation of carboxylate groups was also assumed. The reaction mechanism was discussed on the basis of the results obtained.     

A study of cryostructuring of polymer systems. 45. Effect of porosity of dispersed filler on physicochemical characteristics of composite poly(vinyl alcohol) cryogels

Composite cryogels simulating the properties of waterproof screens of hydraulic structures, such as protruding dykes and dams, have been obtained by a cryogenic treatment (freezing at –10…–30°C followed by incubation in the frozen state for 12 h and defrosting at a rate of 0.03°C/min) of suspensions of calcium-carbonate-containing (marble or coquina) or cellulose-containing (microcrystalline cellulose or sawdust) particles in aqueous poly(vinyl alcohol) solutions. Viscometric examinations of initial suspensions have shown that adhesion contacts arise between filler particles, as well as discrete and continuous phases, already at the stage of suspension preparation, thereby affecting the properties of resulting cryogels. This is most pronounced when high-porosity sawdust is used as a filler. It has been shown that all the dispersed materials used in the work are “active” fillers for poly(vinyl alcohol) cryogels, these fillers increasing the rigidity of the formed composites. Therewith, porous particles, into which the polymer solution can penetrate, are more efficient. The dependence of the composite rigidity on the temperature of the cryogenic treatment has, as a rule, a bell-shaped pattern with a maximum in the region of –20°C. Being tested for water permeability, the obtained model composite cryogels have exhibited pronounced antifiltration properties (the filtration coefficient is ≤(1–2) × 10^–9 cm/s), thus indicating that such materials are promising for solving problems relevant to the protection of fascine hydraulic structures from erosion with snow water.     

Synthesis and characterization of poly(phosphon acetal) derivatives of poly(vinyl alcohol)

Preparation of poly(phosphonoacetals) (PPA) by transacetalation of poly(vinyl alcohol) with diethyl-phosphonoacetal is described. PPA with a degree of substitution of 60% is an alcoholsoluble polymer with a glass transition temperature (T_g) of 67°C. High resolution ¹H and ¹³C NMR spectra reveal the presence of hemiacetals alongside the six-membered acetal ring with an approximate ratio of 2:8 of these substituents. A possible correlation between the microtacticity of the parent PVA and the structure of PPA is indicated; the syndiotactic and isotactic sequences on the parent polymer controls the relationship between the two pendant groups.     

FTIR assessment of poly(ethylene oxide) irradiated in solid state,melt and aqeuous solution

FTIR spectroscopy was used to study poly(ethylene oxide), PEO, irradiated in solid and molten aggregate states and as aqueous solutions of various concentrations. The changes in shape and width of –C–O–C– complex absorption intensities at around 1112 cm^?1 were the most prominent. On irradiation of solid samples in contact with air shrinking of –C–O–C– complex and increase in its absorption intensities indicated predominant degradation. Crosslinking prevailed on irradiation of molten PEO and of its aqueous solutions in nitrogen atmosphere and manifested itself as widening of –C–O–C– absorption and decrease of corresponding intensities. Partial or complete merging of CH₂ wagging vibrations at 1342 cm^?1 and 1360 cm^?1 that are characteristic of crystalline PEO into a single absorption at around 1350 cm^?1 indicated amorphization what was observed for samples that had reduced degree of crystallinity determined by differential scanning calorimetry. DSC could not discriminate between degradation and crosslinking while the changes in width and shape of –C–O–C– complex were independent of the changes in crystallinity. Comparison of FTIR spectra of the same PEO samples obtained as thin film and as KBr pellets revealed that pellet preparation results in a number of spectral artefacts.     

Study of cryostructurization of polymer systems VII. Structure formation under freezing of poly(vinyl alcohol) aqueous solutions

Rheological properties of the cryogels produced by freezing of concentrated aqueous solutions of poly(vinyl alcohol) have been studied. These properties were shown to depend on the polymer concentration in the initial solution, on PVA molecular weight, cryostructurization duration and temperature. Electron microscopy demonstrates the heterogeneous porous structure of these cryogels and the dependence of the observed pattern on the conditions of formation of the studied objects.     

Fourier-transform infrared studies of polymer blends. II. Poly(ϵ-caprolactone)–poly(vinyl chloride) system

Fourier-transform infrared (FTIR) studies of the poly(?-caprolactone) (PCL)–poly(vinyl chloride) (PVC) blend system are presented. The results indicate that there are specific interactions between the PCL and PVC in both the molten and solid states which could be responsible for the apparent compatibility of the amorphous component of these blends. Additionally, FTIR difference spectra are presented to illustrate the potential of this technique for following the kinetics of crystallinity in polymer blend systems.     

Photo‐Induced Electron Transfer Between Photosystem 2 via Cross‐linked Redox Hydrogels

Photosystem 2 (PS2) that catalyses light driven water splitting in photosynthesis was ‘wired’ to electrode surfaces via osmium‐containing redox polymers based on poly(vinyl)imidazol. The redox polymer hydrogel worked as both immobilization matrix and electron acceptor for the enzyme. Upon illumination, the enzymatic reaction could be switched on and a catalytic current was observed at the electrode. The catalytic current is directly dependent on the intensity of light used for the excitation of PS2. A typical current density of 45 μA cm^?2 at a light intensity of 2.65 mW cm^?2 could be demonstrated with a significantly improved operational stability.     

Studies on Synthesis and Effect of Dopants on Conductivity and Morphology of Organically Soluble Poly(o-anisidine)

Synthesis of poly(o-anisidine) doped with various protonic acids by using ammonium persulphate as oxidizing agent were carried out in aqueous acid media. Influences of protonic acids on the physicochemical properties were investigated. The various process parameters were optimized to obtain poly(o-anisidine) in the conducting salt phase form. The results are discussed with references to different protonic acids. It was observed that poly(o-anisidine) is highly soluble in organic solvents, such as m-cresol and N-methyl pyrrolidinone (NMP). The polymers were characterized by UV-Visible, FTIR, SEM, XRD and conductivity measurements. A result shows that, different types of dopant acids HCl, H₂SO₄ and HClO₄ affect the morphology and electrical conductivity of the polymer. The electrical conductivity of the polymer follows the order HCl >H₂SO₄>HClO₄. Thus the effect of dopant ion type and the size of its negative ions influence the physico-chemical properties. UV-Vis absorption spectra shows peaks at 740–783 nm with shoulder at 380–420 nm as characteristic peaks for the emeraldine salt (ES) phase of poly(o-anisidine) POA. The FTIR spectra show a broad and intense band at ～2800–3001 cm^?1 and ～1159–1170 cm^?1 that account for the formation of ES phase of the polymer. The X-ray diffraction spectra show a characteristic peak at 20–30^o, 2θ range which reveals partial crystalline structure. The conductivity of the poly(o-anisidne) salt was found to be in the range of 10^?3 to 10^?2 S/cm. SEM studies of poly(o-anisidine) doped with HCl shows the continuous granular uniform morphology with sub-micrometer evenly distributed particles of size ～100–200 nm.     

Understanding isothermal semicrystalline polymer drying: Mathematical models and experimental characterization

The drying mechanism of semicrystalline poly(vinyl alcohol) (PVA) was investigated. PVA samples of various molecular weights were crystallized by annealing at temperatures slightly above the glass transition temperature of PVA, and swollen in water for different time periods. The water volume fraction in the sample was measured using a buoyancy technique. The samples were dried in air at constant temperatures, and the drying kinetics were investigated using thermogravimetric analysis. The change in degree of crystallinity of the swollen polymer during drying was measured by differential scanning calorimetry (DSC) as well as by Fourier transform infrared spectroscopy (FTIR). The degree of crystallinity of the samples increased during drying, which in turn was found to alter the drying rate. The drying kinetics were faster at higher temperatures, for lower molecular weights, and for lower degrees of crystallinity. A mathematical model was developed to predict drying rates of semicrystalline polymers by considering the crystallization kinetics during drying. The model predictions included the thickness of the polymer sample, the degree of crystallinity of the polymer, and the water weight loss as functions of drying time. Model predictions were found to agree reasonably well with the experimental results. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2771–2780, 1998     

Long branching in poly(vinyl acetate) and poly(vinyl alcohol). II. Polymerization of vinyl acetate in the presence of crosslinked poly(vinyl alcohol)

It is a common view that poly(vinyl acetate) has many branches at the acetyl side group, but that the corresponding poly(vinyl alcohol) has little branching. In order to study the branching in poly(vinyl acetate) and poly(vinyl alcohol) which is formed by chain transfer to polymer, the polymerization of ¹⁴C-labeled vinyl acetate in the presence of crosslinked poly(vinyl acetate), which was able to be decrosslinked to give soluble polymers, was investigated at 60°C and 0°C. This system made it possible to separate as well as to distinguish the graft polymer from the newly polymerized homopolymer. Furthermore, the degree of grafting onto the acetoxymethyl group and onto the main chain were estimated. It became clear that, in the polymerization of vinyl acetate, chain transfer to the polymer main chain takes place about 2.4 times as frequently at 60°C as that to the acetoxy group and about 4.8 times as frequently at 0°C.     

ATR‐FTIR Kretschmann spectroscopy for interfacial studies of a hidden aluminum surface coated with a silane film and epoxy I. Characterization by IRRAS and ATR‐FTIR

Interfacial analysis is essential in many areas of interest, for instance within the ongoing research on environmentally friendly pretreatments of metal surfaces. While studies of the hidden interface between a metal and polymer top‐coat are of great importance, properties of a surface confined between two media are difficult to analyze in detail. Within the two parts of this study, ATR‐FTIR spectroscopy in the Kretschmann geometry is employed as the main analytical tool to study the interface between a thermo‐cured epoxy and aluminum pretreated with a silane film. The technique requires model systems based on thin metal films, but in contrast to most analytical techniques it permits the analysis of a hidden interface. Initial characterization of the silane film formed from a pH‐regulated γ‐APS and BTSE solution was conducted by both ATR‐FTIR Kretschmann and IRRAS spectroscopy. Absorption bands were obtained at 1250–900 cm^?1, assigned to Si? O functionalities, and at ～1570 and ～1410 cm^?1 assigned to acetate existing as a counter‐ion to γ‐APS. After application of the epoxy film, interfacial alterations were detected upon thermal curing including the densification of the epoxy film, the dehydration of aluminum and the formation of molecular epoxy reaction products. Few alterations could be assigned to the silane film. Calculated spectra derived from optical data can verify experimental results and aid data interpretation, and effects of metal oxidation of aluminum were confirmed by introducing gold as an additional substrate. The results showed that ATR‐FTIR Kretschmann spectroscopy is clearly a valuable tool for the study of hidden interfaces of stratified media. Copyright © 2011 John Wiley & Sons, Ltd.