Glucose biosensors prepared by electropolymerization of p-chlorophenylamine with and without Nafion

Two different glucose biosensors for the amperometric determination of glucose, based on poly(p-chlorophenylamide) (PCPA) and bilayer film of PCPA and Nafion (PCPA/Nafion), are successfully developed. These two biosensors show linear amperometric responses to glucose ranging from 2.0×10⁻⁴ to 3.5×10⁻² mol l⁻¹ and 5.0×10⁻⁴ to 7.5×10⁻² mol l⁻¹, respectively, with the same correlation coefficient of 0.9988. Effects of polymerization potential and polymerization time on the performance of enzyme sensors are studied. It is found that PCPA, as a non-conducting polymer, can largely reduce the influence of electroactive interferents. Introduction of inner Nafion membrane not only further eliminates the influence of ascorbic acid on the sensor response but also increases electrode stability.     

Surface characterizations of poly(ethylene terephthalate) film modified by a carbohydrate-bearing photoreactive azide group

Grafting of a carbohydrate UV-reactive molecule, the β-d-galactopyranosyl-(1-4)-1-N-[2-(4-azidophenyl amino)-ethylamino]-1-deoxy-d-glucitol (AzPhLac), has been achieved on poly(ethylene terephthalate) film. The dependence of surface density and yield of grafted AzPhLac have been studied versus the number of moles of UV-treated AzPhLac via the deposit of a drop of solution with a known volume and concentration. A nearly complete grafting of initial AzPhLac molecules was reached for the lowest concentration and lowest volume of solution deposit conditions. Grafting density values in the range of 29-181 nmol/cm² confirm the polymeric nature of the grafted layer. FTIR-ATR demonstrated the heterogeneity in thickness of the grafted surface due to the drop-deposit method and solvent evaporation process. AFM (imaging) allowed us to find a correlation between grafting density and rms roughness. Water-contact angle and AFM (contact mode) gave further evidence of the hydrophilic nature of the extreme surface.     

A novel poly(3,4-ethylenedioxythiophene)-ionic liquid composite coating for the headspace solid-phase microextraction and gas chromatography determination of several alcohols in soft drinks

A novel poly(3,4-ethylenedioxythiophene)-ionic liquid (i.e., 1-hydroxyethyl-3-methyl imidazolium-bis[(trifluoromethyl)sulfonyl]imide) composite film was electrodeposited on a Pt wire for headspace solid-phase microextraction. The film showed nodular structure and had large specific surface. In addition, it displayed high thermal stability (up to 300 °C) and durable property (could be used for more than 200 times). Coupled with gas chromatography-flame ionization detection, the resulting fiber was applied to the headspace solid-phase microextraction and determination of several alcohols (i.e., linalool, nonanol, terpineol, geraniol, decanol and dodecanol). It presented higher extraction capability in comparison with the poly(3,4-ethylenedioxythiophene) and commercial polydimethylsiloxane/divinylbenzene fiber. Under the optimized conditions, the linear ranges exceeded three magnitudes with correlation coefficients above 0.9952 and the low limits of detection were 34.2–81.3 ng L⁻¹. For different alcohols the repeatabilities (defined as RSD) were <5.8% and <7.8% for single fiber (n = 5) and fiber-to-fiber (n = 4), respectively. The proposed method was applied to the determination of these alcohols in real samples with acceptable recoveries from 81.1% to 106.6%.     

Isolation and characterization of poly(butylene succinate)-degrading fungi

We isolated 12 poly(butylene succinate) (PBSu)-degrading fungi from various soil environments. Among the isolates, the NKCM1706 strain exhibited the fastest degradation rate for the PBSu film (10.5 μg cm⁻² h⁻¹). Phylogenetic analysis revealed that this strain is closely related to Aspergillus fumigatus (internal transcribed spacer (ITS) identity, 100%). Further, this strain exhibited PBSu-hydrolytic activity in the presence of poly(?-caprolactone) (PCL), PBSu, and poly(butylene succinate-co-adipate) (PBSA). On adding this strain into the soil sample, the PBSu degradation rate accelerated approximately sixfold, suggesting that this strain plays a crucial role in PBSu degradation in actual soil environments. In addition to PBSu, the NKCM1706 strain could degrade PBSA, poly(ethylene succinate) (PESu), poly(3-hydroxybutyrate) (P(3HB)), and PCL.     

Effects of humidity,imidization history,and thickness on water sorption behavior of poly(p-phenylene biphenyltetracarboximide) films

Poly(p-phenylene biphenyltetracarboximide) films with various thicknesses were prepared from the poly(amic acid) precursor by thermal imidization at 230–400°C for 1–10 h under a nitrogen atmosphere. The water sorption in the films was measured at 25°C over 22–100% relative humidity using a Cahn microbalance as a function of film thickness and thermal imidization history. The water diffusion in all the films followed nearly Fickian process despite the morphological heterogeneity due to the ordered and less ordered phases. The diffusion coefficient and water uptake varied in 0.85 × 10^?10 ? 7.50 × 10^?10 cm²/s and 0.12–2.4 wt %, respectively, depending upon humidity, film thickness, and imidization history. Both diffusion coefficient and water uptake increased with increasing humidity, but decreased as imidization temperature and time increased. With increasing film thickness, the diffusion coefficient increased whereas the water uptake decreased. The water sorption behavior was interpreted with the consideration of morphological variations, such as polymer chain order, in-plane orientation, and intermolecular packing order due to the film thickness and imidization history. © 1995 John Wiley & Sons, Inc.     

Pattern formation of polyimide by using photosensitive polybenzoxazole as a top layer

A versatile method for positive-type patterning of polyimide (PI) based on a two-layer photosensitive poly(benzoxazole) (PSPBO) and poly(amic acid) (PAA) film has been developed to provide a promising material in the field of microelectronics. This patterning system consisted of a pristine PAA thick bottom-layer and a poly(o-hydroxy amide) (PHA) thin top layer with 9,9-bis[4-(tert-butoxycarbonyl-methyloxy)phenyl]fluorene (TBMPF) as a dissolution inhibitor, and (5-propylsulfonyloxyimino-5H-thiophene-2-ylidene)-(2-methylphenyl)-acetonitrile (PTMA) as a photoacid generator (PAG). The PHA and PAA were prepared from 4,4′-(hexafluoroisopropylidene)-bis(o-aminophenol) and 4,4′-oxybis(benzoic acid) derivatives, and 3,3′,4,4′-biphenyltetracarboxylic dianhydride and 4,4′-oxydianiline, respectively, in N,N-dimethylacetamide. This two-layer system based on PHA (150-nm thickness) and PAA (1.5-μm thickness) showed high sensitivity of 35 mJ/cm² and high contrast of 10.3 when exposed to a 365 nm line (i-line), post-baked at 100 °C for 2 min, and developed in a 2.38 wt.% tetramethylammonium hydroxide aqueous solution/5 wt.% iso-propanol at 25 °C. A clear positive image of a 4-μm line-and-space pattern was printed on a film which was exposed to 100 mJ/cm² of i-line by a contact-printing mode and fully converted to the corresponding PBO/PI pattern upon heating at 350 °C, confirmed by FT-IR spectroscopy. This two-layer system could be applied to the patterning of various PAAs.     

Poly(3-methylthiophene)/palladium sub-micro-modified sensor electrode. Part II: Voltammetric and EIS studies, and analysis of catecholamine neurotransmitters, ascorbic acid and acetaminophen

Promising voltammetric sensors based on the modification of Pt and poly(3-methylthiophene) (PMT) electrodes with Pd nanoparticles were achieved for the determination of catecholamine neurotransmitters, ascorbic acid and acetaminophen. Electrochemistry of the indicated compounds was studied at these electrodes and interesting electrocatalytic effects were found. Furthermore, simple, easily prepared one electrochemical step Pd-modified Pt electrode (Pt/Pd) is reported for the first time. Cyclic voltammetry (CV) and chronocoulometry (CC) were used for the determination of the apparent diffusion coefficients in different electrolytes at these electrodes and the values are in the range from 10⁻⁴ to 10⁻⁵ cm² s⁻¹. Furthermore, it was found that the method of polymer formation had a substantial effect on the synergism between the polymer film and the loaded metal particles towards the oxidation of dopamine (DA) in different supporting electrolytes. This was confirmed by the CV, CC and EIS (electrochemical impedance spectroscopy) as well as SEM (Scanning Electron Microscopy) results. Pt and PMT electrodes modified with Pd nanoparticles showed excellent results for the simultaneous determination of tertiary and quaternary mixtures of the studied compounds.     

Electrochemical behavior of α-Keggin-type nanoparticles,Co(en)<Subscript>3</Subscript>(PMo<Subscript>12</Subscript>O<Subscript>40</Subscript>), in polyethylene glycol

The electrochemical behavior of α-Keggin-type nanoparticles, Co(en)₃(PMo₁₂O₄₀) (abbreviated as PMo₁₂-Co), have been studied in poly(ethylene glycol) for four different molecular weights (PEG, average MW 400, 600, 1000, and 2000 g mol^–1) and containing LiClO₄ (O/Li=100/1) supporting electrolyte. The diffusion coefficients of the PMo₁₂-Co nanoparticles were determined using a microelectrode by chronoamperometry for PEG of different molecular weights that were used to describe the diffusion behavior of PMo₁₂-Co nanoparticles in different phase states. Moreover, the conductivity of the composite system increases upon addition of PMo₁₂-Co nanoparticles, which was measured by an a.c. impedance technique. FT-IR spectra and DSC were used to follow the interactions of PEG-LiClO₄-PMo₁₂-Co, and well described the reason that the PMo₁₂-Co nanoparticles could promote the conductivity of the PEG-LiClO₄-PMo₁₂-Co system. Electronic Publication     

Voltammetric Determination of Hydroquinone using β‐Cyclodextrin/Poly(N‐Acetylaniline)/Carbon Nanotube Composite Modified Glassy Carbon Electrode

Abstract

An electrochemical sensor for hydroquinone (HQ) using β‐cyclodextrin/poly(N‐acetylaniline)/carbon nanotube composite (β‐CD/PAA/MWNTs) modified glassy carbon electrode has been successfully developed. Based on the synergistic effect of MWNTs and conducting PAA polymer and the accumulation effect of β‐CD, the analytical response of the β‐CD/PAA/MWNTs film to the electrochemical behavior of HQ was better than that of a β‐CD/PAA film, a PAA/MWNTs film, a PAA film, or a bare glassy carbon (GC) electrode. Under the conditions chosen, the anodic currents increased linearly with HQ concentration from 1×10^?6 to 5×10^?3 mol l^?1 and the detection limit was 8×10^?7 mol l^?1. This electrochemical sensor showed excellent reproducibility, stability and recovery for the determination of HQ.     

Development and characterization of a titanosilicate ETS-10-coated optical fiber reactor towards the photodegradation of methylene blue

An optical fiber reactor (OFR) system containing uniformly distributed quartz fibers coated with titanosilicate ETS-10 crystals was investigated. Optimum ETS-10 film thickness (～1.5 μm) and coating length (15 cm) were determined from the light propagation analysis in a single ETS-10-coated fiber. The nearly constant value of the attenuation coefficient (α ≈ 0.10 cm^?1) for films with different thickness indicated uniform fiber surface coverage with these films. The extinction coefficient, ?, decreased from ～1.6 to ～1.0 μm^?1 with ETS-10 film thickness increasing from ～0.5 to ～1.5 μm, which suggested less contact per unit film thickness between light and ETS-10 crystals inside thicker films, likely due to their lower crystal packing density. Photodegradation of methylene blue (MB) conducted in the OFR showed higher photocatalytic activity for thicker ETS-10 films. Although higher MB photodegradation rates were obtained at higher light intensity, the apparent quantum efficiency, Φ, decreased with increasing light intensity. This is consistent with the charge separation mechanism for MB photodegradation in the UV light range investigated. All ETS-10 samples investigated showed ～4–5 times higher Φ values in the OFR than in the slurry reactor, likely due to the unique light/photocatalyst/reactant contact and high fiber packing density in the OFR.     

Electrochemical and Spectroelectrochemical Studies on Pyridoxine Hydrochloride Using a Poly(methylene blue) Modified Electrode

The electrochemical redox processes of pyridoxine hydrochloride (VB₆) at a poly(methylene blue) film modified glass carbon electrode (PMBE) in a phosphate buffer solution (PBS, pH 8.0) were studied by cyclic voltammetry. The VB₆ electrode reaction with quasi‐reversible characteristics was diffusion‐controlled at low scan rates and adsorption‐controlled at high scan rates. The anodic peak current positive to 0.6 V (vs. SCE) was found to be proportional to the concentration of VB₆ in the range of 0.010 to 1.03 mg?mL^?1 with a detection limit of 1.34 μg mL^?1. Fluorescence and UV‐vis absorption spectroelectrochemical measurements suggest that the pyridine ring was not destroyed over the potential range from ?0.8 to 1 V (vs. SCE), and the electrocatalytic generation of pyridoxal was anodically started at 0.57 V.     

Diffusion and partition coefficients of small organic solvents in molten miscible polymer blends: Correlations with thermodynamic interactions

The transport properties of small organic molecules in molten poly(vinyl chloride) (PVC)/atactic poly(methyl methacrylate) (PMMA) blends and their homopolymers were studied with inverse gas chromatography. The elution profiles resulting from various organic solvents and different experimental conditions were used for measuring diffusion and partition coefficients. With the van Deemter equation and retention volumes at infinite dilution, diffusion coefficients of 10^?7 to 10^?8 cm²/s and partition coefficients of 10–50 were calculated. The dependence of the diffusion and partition coefficients on experimental variables such as the blend concentration, temperature, and solute nature was examined. The presence of PMMA in PVC blends affected the sorption behavior of the PVC matrix up to a certain concentration. Beyond that, it was hard to derive any composition–diffusivity dependence. On the contrary, the diffusion and partition coefficients were greatly influenced by changes in the temperature and by the nature of the solute. For those solutes (e.g., chlorinated hydrocarbons) showing stronger interactions with polymer blends (higher negative values for the Flory–Huggins interaction parameter χ₁₍₂₃₎), higher diffusion and partition coefficients were obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 267–279, 2004     

Differential pulse voltammetric determination of trace Te(IV) at a poly(3,3′-diaminobenzidine) film modified gold electrode in flow systems

Electropolymerization of 3,3′-diaminobenzidine on a gold surface gave an adherent, stable film of poly(3,3′-diaminobenzidine) (PDAB). This polymer film retained the complexational functionalities of its monomer, demonstrating preconcentration abilities for several ions, including Se(IV) and Te(IV). In particular, in this work, continuous flow and flow injection methods were developed for the sensitive and selective determination of Te(IV). The optimized method for the continuous flow mode had a detection limit of 5.6×10⁻⁹ mol l⁻¹ for 10 min preconcentration. Typical relative standard deviations for six consecutive determinations were 1.82 and 2.56% for Te(IV) concentrations of 1.0×10⁻⁶ and 5.0×10⁻⁸ mol l⁻¹, respectively (10 min preconcentration). The method was applied to the determination of Te(IV) in real samples.     

Studies on Synthesis and Effect of Dopants on Conductivity and Morphology of Organically Soluble Poly(o-anisidine)

Synthesis of poly(o-anisidine) doped with various protonic acids by using ammonium persulphate as oxidizing agent were carried out in aqueous acid media. Influences of protonic acids on the physicochemical properties were investigated. The various process parameters were optimized to obtain poly(o-anisidine) in the conducting salt phase form. The results are discussed with references to different protonic acids. It was observed that poly(o-anisidine) is highly soluble in organic solvents, such as m-cresol and N-methyl pyrrolidinone (NMP). The polymers were characterized by UV-Visible, FTIR, SEM, XRD and conductivity measurements. A result shows that, different types of dopant acids HCl, H₂SO₄ and HClO₄ affect the morphology and electrical conductivity of the polymer. The electrical conductivity of the polymer follows the order HCl >H₂SO₄>HClO₄. Thus the effect of dopant ion type and the size of its negative ions influence the physico-chemical properties. UV-Vis absorption spectra shows peaks at 740–783 nm with shoulder at 380–420 nm as characteristic peaks for the emeraldine salt (ES) phase of poly(o-anisidine) POA. The FTIR spectra show a broad and intense band at ～2800–3001 cm^?1 and ～1159–1170 cm^?1 that account for the formation of ES phase of the polymer. The X-ray diffraction spectra show a characteristic peak at 20–30^o, 2θ range which reveals partial crystalline structure. The conductivity of the poly(o-anisidne) salt was found to be in the range of 10^?3 to 10^?2 S/cm. SEM studies of poly(o-anisidine) doped with HCl shows the continuous granular uniform morphology with sub-micrometer evenly distributed particles of size ～100–200 nm.     

The effect of ionic strength on the diffusion of 125I in Gaomiaozi bentonite

The diffusion of ¹²⁵I^? in compacted Gaomiaozi (GMZ) bentonite was investigated by capillary in-diffusion method. Apparent and effective diffusion coefficients and accessible porosity of iodide in GMZ bentonite were obtained, and the effect of ionic strength on diffusion parameters was studied. The apparent diffusion coefficients of iodide in compacted GMZ bentonite are in the range of 1.0–6.0 × 10^?10 m² s^?1 under the conditions of dry bulk density 1,500 kg m^?3 and temperature 298 K, and increase with increasing ionic strength. This effect was explained through the analysis of microscopic structure of compacted bentonite. The iodide can only diffuse in unbound interparticle pore solution of compacted bentonite. The apparent diffusion coefficient is a function of accessible porosity which is decided by the thickness of diffusion double layer, and the thickness is in turn controlled by ionic strength.     

Thermoreversible gelation in polymer systems—I : The sol-gel transition in dilute poly(vinyl chloride) gels

The gel to sol transition temperature (T_m) has been obtained at several concentrations between 25 g l⁻¹ and 140 g l⁻¹ for six different samples of poly(vinyl chloride) in dioxan and at concentrations of 63 g l⁻¹ and 92 g l⁻¹ for a particular sample of poly(vinyl chloride) in several solvents.     

Diffusivity enhancement of water vapor in poly(vinyl alcohol)–fumed silica nano-composite membranes: Correlation with polymer crystallinity and free-volume properties

The diffusion coefficients of water vapor in poly(vinyl alcohol)–fumed silica (PVA–FS) nano-composite membranes were determined using the gravimetric method. Water vapor was observed to diffuse more rapidly in membranes with increased FS content. The vapor diffusion coefficient was determined as 1.2 × 10⁻¹³ m²/s in pure PVA and was observed to increase to 3.0 × 10⁻¹³ m²/s in PVA composites containing 30% FS nano-particles. The free-volumes of PVA–FS membranes were characterized using positron annihilation lifetime (PAL) spectroscopy. PAL results showed that both the ortho-positronium (o-Ps) lifetime and intensity increased with the addition of FS. The intensity (I₃) was found to be higher than the estimated value determined from the linear combination of the data from pristine PVA and FS, and correlated excellently with the polymer amorphous content. The PAL results indicate that a higher FS content in PVA increases the free-volume hole size (a volume increase from 40 to 55 Å³) and free-volume hole density (an I₃ increase from 23 to 28%), resulting in a higher fractional free-volume in the nano-composites. The increase in the relative polymer free-volume with higher FS content was associated with a decrease in the PVA crystallinity, as determined from differential scanning calorimetry measurements. It is postulated that the incorporated FS nano-particles interrupt polymeric chain packing and retard crystallization during membrane formation. More crystalline segments were transformed into amorphous regimes in the nano-composites containing more FS. A correlation between water diffusivity and the fractional free-volume was obtained, and the water diffusivity was successfully expressed by the free-volume theory.     

Diffusive desorption of small solute molecules from amorphous polymers: poly(methyl methacrylate), poly (vinyl acetate) and poly(n-alkyl 2-cyanoacrylates)

Diffusion coefficients of some aromatic substances in poly(vinyl acetate) and poly(methyl methacrylate) have been measured from desorption rates into aqueous buffers from solid solutions of diffusant in cast polymer films. With ordinary spectrophotometric instrumentation, extension of the measurable range of the diffusion coefficient at infinite dilution to below 10^?21 m² sec^?1 is sometimes possible. Measures values below 10^?12 m² sec^?1 are generally much more quickly obtained, and are apparently at least as reproducible as those obtained by time-lag methods, permitting differential effects of diffusant molecular weight and shape to be studied, with solutes of higher molecular weight than those to which previous published studies were confined. Diffusion coefficients of the same solutes in a number of poly(n-alkyl 2-cyanoacrylates) were measured by desorption from polymer particles and films. The rank order and general dependence of diffusivity upon molecular weight and shape is similar in all three polymers. There is a tendency for the ionic and basic solutes to become bound, probably by covalent linkage, to poly(n-alkyl 2-cyanoacrylate) molecular chain ends.     

The Determination of Salbutamol Sulfat Based on a Flow‐Injection Coupling Irreversible Biamperometry at Poly(aminosulfonic acid)‐Modified Glassy Carbon Electrode

Abstract

The present work describes the development of a simple and efficient method for electrochemical analysis determination of SBS using polymer film coated modified electrode. A glassy carbon electrode (GCE) is successfully modified with electropolymerized film of aminosulfonic acid (ASA) in pH 6.8 phosphate buffer solution (PBS). Cyclic voltammetry (CV) were used to study the electrochemical properties of the polymer film and the appropriate condition for electropolymerization process. The voltammetric behavior of SBS at the PASA GC CMEs has been investigated, the results suggest that the PASA GC CMEs have good effect of electrocatalytic oxidation action to SBS, also propose the mechanism toward SBS. The flow‐injection irreversible biamperometry analysis method was studied under the applied potential difference of 0 V to determinate SBS. In 0.1 mol l^?1 (pH 6.80) phosphate buffer solution, a sensitive and irreversible oxidation peak was obtained at the PASA GC CMEs. Under the optimum conditions, SBS can be determined from the range 2.0×10^?6 to 1.0×10^?3 mol · 1^?1 with the sampling frequency of 100 samples per hour. The detection limit for SBS is 6.5×10^?7 mol l^?1 and the RSD for 20 replicate determinations of 4.0×10^?5 mol l^?1 SBS is 1.85%. The method is simple, with high selective rapid and sensitive. The method is applied to the determination of SBS in the drug with satisfactory results. Moreover, the physiologically common interferents (i.e., sucrose, lactose, citric acid, and citrate) negligibly affected the response of SBS. The PASA GC CMEs film‐coated electrode exhibited a stable and sensitive response to salbutamol sulfat in the presence of electrocatalysis oxidation.     

Proton transport properties in hybrid membranes investigated by ac-electrogravimetry

In this paper, a hybrid organic/inorganic membrane, based on poly(VDF-co-HFP) polymer associated to mesostructured modified silica and made through sol–gel techniques, was characterized by using ac-electrogravimetry. In order to perform experiments, a polypyrrole–heteropolyanion doped mediator film was inserted between the working electrode of the microbalance and the hybrid membrane. This mediator film, which is characterized by mixed conducting properties, is necessary to provide proton transfer between the different interfaces and in that way, the proton transport inside the hybrid film which is only an ionic conducting material. Proton transfer and transport was characterized through ac-electrogravimetry and an original theoretical approach was developed for extracting the attractive parameters. The change of the exchanged species concentration and the diffusion coefficient of the protons in the hybrid membrane, were estimated, for the first time, according to the applied potential. These studies pointed out that the low conductivity value in this hybrid membrane is related to i) the low diffusion coefficient of proton (10^? 7 cm² s^? 1) in this membrane associated, ii) the low concentration of proton in the membrane (0.4 meq g^? 1).