低表面能侧基含氟聚合物*

含氟聚合物材料具有优异的热稳定性、极低的表面能、强化学稳定性和生物相容性等,在功能涂料、织物整理、微电子、汽车以及航空航天等领域具有很好的应用前景。本文综述了侧基含氟聚合物的主链、全氟烷基链、主链与全氟烷基链段间连接基团的结构对聚合物表面性能的影响,并总结了环境友好型低表面能侧基含氟聚合物的研究进展。     

含氟丙烯酸酯共聚物结晶性与涂膜表面润湿性能研究

以甲基丙烯酸2-全氟辛基乙酯( FOEMA)分别和不同烷烃链长丙烯酸酯(RA,CH2=CHCOOCnH2n+1,n=4,8,12,16,18)为单体,用自由基聚合法合成了一系列的含氟丙烯酸酯共聚物,通过X射线衍射(XRD)和示差扫描量热法(DSC)对共聚物进行了表征,发现结晶性与丙烯酸酯的烷烃链长度密切相关,当n=4,...     

含氟丙烯酸酯共聚物制备超疏水表面及其形成机理的研究

以丙烯酸全氟烷基乙基酯和甲基丙烯酸甲酯为共聚单体, 分别以用微乳液聚合法和溶液聚合法制备的无规共聚物和用可逆加成-断裂链转移制备的嵌段共聚物作为成膜共聚物, 并以1,1,2-三氟三氯乙烷作为溶剂, 采用溶剂挥发成膜法可以直接制备出超疏水膜, 聚合物膜对水的接触角可达160°. 改变聚合物结构和成膜条件, 探讨了该类超疏水膜的形成机理和影响因素. 发现膜的表面形貌和疏水性与共聚物的组成、结构、分子量以及成膜条件密切相关, 随着共聚物中氟含量的增大, 膜的表面形貌都趋于平滑; 而且, 无规共聚物比嵌段共聚物更易形成粗糙度好的膜; 同时, 较大的聚合物分子量和适宜的高的成膜温度都对形成粗糙结构有利.     

含氟丙烯酸酯-苯乙烯共聚物的制备及其表面性能的研究

研究了聚合工艺、含氟丙烯酸酯类单体种类和用量、苯乙烯和自由基引发剂用量及硅烷偶联剂、催化剂等因素对含氟丙烯酸酯-乙烯共聚物表面性能的影响。结果表明：聚合工艺、含氟丙烯酸酯类单体种类和用量对共聚物表面的憎水性能有显著的影响;采用延时滴加含氟丙烯酸酯类单体可提高共聚物膜表面的憎水性;随含氟丙烯酸酯类单体侧链含氟烷基的链长和氟原子数及含氟单体用量的增加,共聚物水接触角增大,吸水率下降;共聚物薄膜的硬度则与含氟丙烯酸酯类单体中α-取代基、侧链含氟烷基的链长和用量、苯乙烯用量、引发剂浓度等相关;硅烷偶联剂和催化交联剂的加入可提高共聚物薄膜的强度。     

含氟丙烯酸酯共聚物防粘剂的制备及其表面性能研究

以甲基异丁基甲酮为溶剂,偶氮二异丁腈为引发剂,全氟烷基乙基丙烯酸酯、丙烯酸十八酯、丙烯酸丁酯和甲基丙烯酸羟乙酯为原料,溶液聚合制得了均一的含氟丙烯酸酯共聚物防粘剂,并研究了其表面性能。结果表明:全氟烷基乙基丙烯酸酯单体的加入显著降低了共聚物的表面能,提高了共聚物膜的硬度、耐水、耐碱、耐溶剂等性能。当加入ω(氟单体)为30%时,表面能降低至14.7 mN/m,低于有机硅类防粘剂的表面能,含氟丙烯酸酯共聚物膜与压敏胶的的剥离力较低,剩余粘附率为93.2%,该共聚物膜的防粘等综合性能最好。     

优化含氟丙烯酸酯共聚物乳胶膜表面性能的方法研究

含氟丙烯酸酯乳液由于氟的引入具有优异的表面性能,在涂料、胶粘剂、纺织助剂等领域得到广泛应用.然而含氟单体成本较高,而且产物中乳化剂的存在影响了含氟丙烯酸酯乳液涂膜的抗污、疏水疏油等特性.如何采取有效措施提高含氟丙烯酸酯共聚物乳胶膜的表面性能,是其走向产业化急需解决的问题.针对这方面问题,本文主要从含氟单体的利用率、设计乳胶粒结构、共聚物链结构以及乳胶膜的后处理等方面对近年来的研究成果进行了综述.     

亲水单体对聚氨酯-含氟丙烯酸酯复合乳液颗粒和表面性能的影响

为了提高聚氨酯-丙烯酸酯聚合物的耐水性和耐溶剂性, 将N-甲基二乙醇胺(MDEA)扩链的交联聚氨酯丙酮溶液作为反应介质, 以苯乙烯、丙烯酸丁酯、含氟丙烯酸酯(FA)为单体, 过氧化苯甲酰为引发剂, 通过溶液聚合相转化法制得新型阳离子聚氨酯-含氟丙烯酸酯复合乳液. 研究了MDEA对聚合物水分散液的乳胶粒径、Zeta电位以及乳胶膜表面性能的影响, 并用FTIR, TEM对聚合物的结构和乳胶粒形态进行了表征. 结果表明, MDEA的添加利于降低乳胶粒径, 但对乳胶膜的疏水性能有不利影响, 当MDEA的质量分数为13.15%时, FPUA乳胶粒的形态呈球形, 粒径约为253 nm, 乳胶膜的表面自由能低于25.1 mJ/m², 接触角衰减速率约为0.38 (º)/min. 另外, 乳胶膜的高温处理能够使表面自由能降低11.5%以上.     

有机硅、氟高分子表面活性剂在建材中的应用发展

综述了有机硅、含氟高分子表面活性剂及含有机硅氟的高分子表面活性剂的种类和研究进展,介绍了它们在涂料工业、塑料工业等建材领域中的应用。     

脂环含氟环氧化合物的光固化及其性能研究

脂环环氧树脂是高活性的光固化材料,但折射率、介电常数以及耐水性方面需要改进。本文对比研究了两种脂环型含氟环氧化合物1,4-双(2,3-环氧环己基氧基)四氟丁烷(TCE)和1,6-双(2,3-环氧环己基氧基)八氟己烷(OCE),并与结构相近的商品脂环环氧树脂ERL-4221比较了光固化动力学,动态力学、热、光学以及表面能性能。TCE和OCE具有类似ERL-4221的高光固化反应活性,提高固化反应温度对含氟环氧化合物的速率和转化率的促进作用更明显;DMA以及TGA测试的结果显示,光固化的含氟环氧化合物C-TCE和C-OCE的玻璃化转变温度都高于150℃,分子链更柔软,耐热性略优于C-ERL-4221;接触角测试结果表明,氟原子取代提高了材料表面的疏水和疏油性,氟含量越高,表面能越低;光固化的C-TCE和C-OCE在可见-近红外波段光学透明。表明TCE和OCE作为先进可光固化材料有极大的应用前景。     

热处理对超疏水性含氟丙烯酸酯共聚物膜表面性能的影响

以微乳液聚合法和溶液聚合法制备丙烯酸全氟烷基乙基酯和甲基丙烯酸甲酯的共聚物, 以1,1,2-三氟三氯乙烷为溶剂, 采用溶剂挥发成膜法直接制备出超疏水膜, 并研究120 ℃热处理对超疏水膜表面性能的影响. 对于用乳液聚合方法制备的超疏水膜, 随着热处理时间的延长, 滚动角表现出先逐渐增大直至完全不能滚动, 然后重新回复到极小滚动角的特殊变化过程, 而静态接触角只是略微减小, 完全不同于热处理对平滑的含氟聚合物表面接触角的影响. 扫描电镜结果显示, 聚合物膜表面形貌对应出现从微/纳复合粗糙结构到微孔粗化并重新形成微/纳复合多层粗糙结构的变化.     

非共价键自组装制备聚对苯撑乙炔/聚丙烯酸水溶性荧光纳米粒子及其光物理行为研究

通过功能化聚对苯撑乙炔(含羟基与氨基)和聚丙烯酸之间的非共价键自组装制备了一系列含共轭聚合物的水溶性荧光纳米粒子, 并进行了相关结构和光学性质表征. 研究表明, 纳米粒子的大小和聚丙烯酸/聚对苯撑乙炔质量比直接相关. 光物理性质研究表明, 形成水溶性纳米粒子后, 疏水的聚苯撑乙炔链在纳米粒子中易于形成π-链间聚集, 其光物理性质与其在薄膜态时相似.     

Photo-grafting Poly(acrylic acid) onto Poly(lactic acid) Chains in Solution

Poly(lactic acid)(PLA)is one of the most important bio-plastics,and chemical modification of the already-polymerized poly(lactic acid)chains may enable optimization of its material properties and expand its application areas.In this study,we demonstrated that poly(lactic acid)can be readily dissolved in acrylic acid at room temperature,and acrylic acid can be graft-polymerized onto poly(lactic acid)chains in solution with the help of photoinitiator benzophenone under 254 nm ultraviolet(UV)irradiation.Similar photo-grafting polymerization of acrylic acid(PAA)has only been studied before in the surface modification of polymer films.The graft ratio could be controlled by various reaction parameters,including irradiation time,benzophenone content,and monomer/polymer ratios.This photo-grafting reaction resulted in high graft ratio(graft ratio PAA/PLA up to 180%)without formation of homopolymers of acrylic acid.When the PAA/PLA graft ratio was higher than 100%,the resulting PLA-g-PAA polymer was found dispersible in water.The pros and cons of the photo-grafting reaction were also discussed.     

Synthesis and Properties of IPN Hydrogels Based on Konjac Glucomannan and Poly（acrylic acid）

As a random copolymer of β-(1,4) linked D-mannose and D-glucose, konjac gluco- mannan (KGM) is a naturally occurring water-soluble polysaccharide, and has been paid attention in the field of drug controlled release carriers potentially used in colon1,2. …     

Poly(acrylic acid)-silicon Hybrids Prepared via a RAFT-mediated Process and Covalent Immobilization of Glucose Oxidase

A surface modification technique was proposed for the modification of silicon surface with glucose oxidase (GOD). The silicon surface was first graft copolymerized with acrylic acid (AAc) via surface-initiated reversible addition-fragmentation chain-transfer (RAFT)-mediated process. With the aid of a water-soluble carbodiimide, GOD was then covalently immobilized on the silicon surface through the amide linkage between the amino group of GOD and the carboxyl group of the grafted AAc polymer. The changes in the surface composition after polymer grafting and enzyme immobilization on the silicon surface were investigated using X-ray photoelectron spectroscopy (XPS). The amount of GOD immobilized could be varied by changing the thickness of the polymer layer and the immobilization time. The GOD-functionalized silicon hybrids are potential useful in the application of the silicon-based biosensors.     

疏水缔合水溶性聚合物P(DMDAAC-NVP-IOA)与萘普生相互作用及释药性

以水为介质,采用自由基胶束聚合制备了二甲基二烯丙基氯化铵(DMDAAC)、N-乙烯基吡咯烷酮(NVP)和丙烯酸异辛酯(IOA)三元共聚疏水缔合水溶性聚合物P(DMDAAC-NVP-IOA),测定了聚合物的聚电解质性质和疏水缔合性质.应用IR、XRD、DSC测试技术研究了各组分的相互作用.结果表明,所制备的P(DMDAAC-NVP-IOA)同时具有聚电解质和疏水缔合特性.随P(DMDAAC-NVP-IOA)量增加,IR分析中萘普生羧基的羰基伸缩振动峰1 684 cm-1处峰变宽、强度明显减弱;XRD分析中的12°～29°间衍射峰逐渐变宽、变小直至消失;DSC分析中只有1个转变曲线,P(DMDAAC-NVP-IOA)与萘普生之间存在分子级相互作用.在pH=7.4磷酸盐缓冲液中,疏水缔合水溶性聚合物具有药物缓释特性,可用扩散-溶解模型进行最佳拟合.     

Network Paired Polymers Based on Poly(acrylic acid)

Network paired polymers (interpolymers) capable of limited swelling in aqueous media accompanied by the formation of polyelectrolyte hydrogels exhibiting рН and thermal sensitivity are synthesized by the reactions of poly(acrylic acid) with poly(methyl methacrylate) and poly(N-vinylcaprolactam) modified by the introduction of anchor oxirane moieties.     

Effect of pH on Poly(acrylic acid) Solution Polymerization

The free-radical redox-initiated aqueous solution polymerization of fully and partially neutralized acrylic acid was carried out at room temperature under full exposure to air. The effect of neutralization degree on the polymerization rate and product properties was studied. Increasing neutralization of the reaction mixture with sodium hydroxide resulted in greater conversion of acrylic acid to sodium acrylate. The rate of polymerization, determined from a gravimetric off-line water removal technique, was shown to decrease significantly with decreasing degree of neutralization. Molecular weight also decreased with decreasing degree of neutralization. The glass transition temperature and hydrophilicity of the polymer product decreased with increasing degree of neutralization. In-line infrared monitoring was also used to monitor the reaction progress and was shown to be an effective tool for this purpose.     

Synthesis and characterization of Poly(N-isopropylacrylamide)/Poly(acrylic acid) semi-IPN nanocomposite microgels

A novel pH- and temperature-sensitive nanocomposite microgel based on linear Poly(acrylic acid) (PAAc) and Poly(N-isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was synthesized by a two-step method. First, PNIPA microgel was prepared via surfactant-free emulsion polymerization by using inorganic clay as a crosslinker, and then AAc monomer was polymerized within the PNIPA microgel. The structure and morphology of the microgel were confirmed by FTIR, WXRD and TEM. The results indicated that the exfoliated clay platelets were dispersed homogeneously in the PNIPA microgels and acted as a multifunctional crosslinker, while the linear PAAc polymer chains incorporated in the PNIPA microgel network to form a semi-interpenetrating polymer network (semi-IPN) structure. The hydrodynamic diameters of the semi-IPN microgels ranged from 360 to 400 nm, which was much smaller than that of the conventional microgel prepared by using N,N′-methylenebis(acrylamide) (MBA) as a chemical crosslinker, the later was about 740 nm. The semi-IPN microgels exhibited good pH- and temperature-sensitivity, which could respond independently to both pH and temperature changes.