乙醇基体改进ICP-MS法直接测定植物中的痕量As、Se、Sb和Te

建立了HNO3-H2O2高压密闭消解、2%乙醇基体改进电感耦合等离子体质谱法(ICP-MS)测定植物中As、Se、Sb和Te的新方法。探讨了乙醇基体对As、Se、Sb和Te信号的增敏效应,以2%乙醇作基体改进剂,各元素信号增敏因子在2~6之间。方法的检出限(3σ)分别为0.0450、2.49、0.0892、0.0202μg/L,相对标准偏差均小于3.6%。     

纯铜、纯镍中磷的ICP-MS法测定

试验了31 P的ICP MS法的测定条件 ,建立了纯铜、纯镍中微量磷的测定方法。采用基体匹配消除基体影响 ,方法检出限为 0 .5 4ng/mL ,测定下限为质量分数 5 .4× 1 0 - 4 % ,回收率为 93.5 %～ 1 0 2 %。对于w(P) <1× 1 0 - 3%和w(P)≥1× 1 0 - 3%的试样 ,其RSD(n =5 )分别为 1 5 %和 6.1 %。本法与光度法分析结果一致 ,较光度法快速、简便     

HG-ICP-MS同时测定生物样品中痕量As,Se,Hg

以HNO3为介质,采用自行研制的二级气液分离器代替易消耗的膜分离器,在优化的实验条件下,采用HG-ICP-MS实现了As,Se,Hg的同时测定,分别获得了0.022,0.016,0.009 ngmL的检出限。实验研究了二级气液分离器中的气液分离行为、样品酸度、NaBH4质量浓度和引入方式等因素对测定灵敏度和精密度的影响。实验的结果表明,HG-ICP-MS同时测定As,Se,Hg的主要干扰来自于Fe,cu等过渡金属离子,样品溶液中抗坏血酸-硫脲的加入可以掩蔽这些离子的干扰。利用所建立的方法测定了人发、灌木叶和大米粉标样中痕量的As,Se,Hg,结果与标准参考值相符。     

氢化物发生电感耦合等离子体发射光谱测定土壤样品中痕量砷锑铋

研究了氢化物发生ICP AES法测定土壤样品中痕量As、Sb和Bi的各种条件 ,拟定了分析方法。用本法对 4个土壤标样进行分析 ,结果与推荐值一致。方法的检出限为 (× 1 0 - 6) :As0 .0 7,Sb0 .0 3,Bi0 .0 2。     

电感耦合等离子体质谱测定中草药中痕量稀土元素的研究

本文报道了微波消解／ICP－MS测定中草药中痕量稀土元素的新方法。在优化实验条件下，方法的检出限为0.71-15.2pg/mL，相对标准偏差为0.80%-3.3%，加标回收率为87.4%-106%。该法具有操作简便、快速、灵敏度高、准确度好和多元素同时测定等优点。     

连续氢化物ICP-AES法测定土壤中痕量铅

以过硫酸铵－过氧化氢作氧化剂，将二价铅氧化为四价铅，与KBH4反应生成气态氢化物（PhH4)，由氩气导入等离子体中进行测定，采用正交 试验法优化分析条件，用标准加入法的结果经计算机多次迭代处理，以校正基体干扰，对国家土壤标准物质进行分析，结果满意。     

微波消解氢化物发生ICP—AES法测定川山紫中痕量硒

建立了微波消解连续氢化物发生ICP AES法测定川山紫中痕量硒的方法 ,系统地研究了微波消解、氢化物发生的最佳条件 ,方法简便快速 ,检出限为 0 .0 0 38μg·ml- 1,RSD为 1.13% (n =10 ,0 .5 4 7μg·g- 1Se) ,样品加标回收率为 99.2 4 %。     

石墨炉原子吸收光谱法测定高纯镍中痕量杂质砷

利用石墨炉原子吸收光谱法，在等温平台条件下测定了高纯镍中痕量杂质砷。方法的特征质量为1．9pg，相对标准偏差为1．4％，加标回收率为95％－103％。     

ICP—AES法测定镍基合金中合金元素含量

ＩＣＰ ＡＥＳ法灵敏度高 ,线性范围宽 ,并同时测定多种元素 ,已成为现代分析测试技术中一个重要的检测手段 ,广泛地应用在各个领域。由于核电用材镍基合金焊丝及焊带是以镍作为基体 ,硅、锰、铬、铁等元素含量较高 ,而钛、铝的含量却很低 ,其基体较复杂 ,各元素含量相差又较悬殊 ,所以给分析工作带来困难。本文采用ＰＳ 6型ＩＣＰ多道真空光谱仪 ,通过对镍基合金试样的溶解方法、等离子体发射光谱仪的工作参数、共存元素的干扰、离峰分析校正等进行了研究 ,从而制定了相应准确有效的方法 ,解决了生产检测的困难 ,结果满意[1] 。1　试验部分…     

Determination of As, Sb, Se, Te and Bi in milk by slurry sampling hydride generation atomic fluorescence spectrometry

A simple and fast analytical procedure has been developed for the determination of As, Sb, Se, Te and Bi in milk samples by hydride generation atomic fluorescence spectrometry (HG-AFS). Samples were treated with aqua regia for 10 min in an ultrasound water bath and pre-reduced with KBr for total Se and Te determination or with KI and ascorbic acid for total As and Sb, the determination of Bi being possible in all with or without pre-reduction. Slurries of samples, in the presence of antifoam A, were treated with NaBH₄ in HCl medium to obtain the corresponding hydrides, and AFS measurements were processed in front of external calibrations prepared and measured in the same way as samples. Results obtained by the developed procedure compare well with those found after microwave-assisted complete digestion of samples. The proposed method is simple and fast, and only 1 ml of milk is needed. The values obtained for detection limit are 2.5, 1.6, 3, 6 and 7 ng l⁻¹ for As, Sb, Se, Te and Bi respectively in the diluted samples, with average relative standard deviation values of 3.8, 3.1, 1.9, 6.4 and 1.2% for three independent analysis of a series of commercially available samples of different origin. Data found in Spanish market samples varied from 3.2±0.3 to 11.3±0.2 ng g⁻¹ As, from 3.1±0.2 to 11.6±0.4 ng g⁻¹ Sb, from 10.7±0.5 to 25.5±0.4 ng g⁻¹ Se, from 0.9±0.2 to 9.4±0.6 ng g⁻¹ Te and from 11.5±0.1 to 27.7±0.4 ng g⁻¹ Bi.     

Determination of As,Bi, Sb and Sn in conifer needles from various locations in Poland and Norway by hydride generation inductively coupled plasma atomic emission spectrometry

Hydride generation inductively coupled plasma atomic emission spectrometry (HG-ICP-AES) in the system with aerosolised sample introduction has been employed for the first time for analysis of conifer needles. Arsenic, bismuth, antimony and tin along with other trace elements were simultaneously determined in pine, spruce, yew and thuja foliage sampled from various locations in Poland and Norway. Quality of the measurements was assured by examination of two attested plant reference materials. The application of different analyte introduction techniques and interference effects from matrix elements, i.e. Na, K, Mg, Ca and transition metals in the analysis of needles are discussed.     

Possibilities and limits of the simultaneous determination of As, Bi, Ge, Sb, Se, and Sn by flow injection-hydride generation-inductively coupled plasma-time-of-flight mass spectrometry (FI-HG-ICP-TOFMS)

A simultaneous multi-elemental measurement of As, Bi, Ge, Sb, Se, and Sn was performed in this study by flow injection-hydride generation-inductively coupled plasma-time-of-flight mass spectrometry (FI-HG-ICP-TOFMS). An off-line pre-reduction treatment using a solution of 5% (m/v) KI and ascorbic acid for 15 min at 80 °C is described by presenting its advantages and disadvantages and compared with the results achieved without pre-reduction. Using optimised conditions the following figures of merit were achieved: limits of detection in the 0.08-0.54 ng ml⁻¹ range and relative standard deviations (RSD) of 1.7-6.7%, respectively. Applying the presented method, two certified reference materials (NIST 1643d freshwater and PACS-2 marine sediment) were analysed to demonstrate the suitability of the method for analysis of real samples. Results obtained from treated samples showed good agreement with certified values while the untreated ones considerably departed from them.     

Determination of tin in soil by continuous hydride generation and inductively coupled plasma mass spectrometry

A method was investigated for the determination of Sn in soil samples by KOH fusion followed by continuous hydride generation coupled with inductively coupled plasma mass spectrometry (HG-ICP-MS). Sample solutions in 3.0 M HCl were mixed in line with a solution of 2.4% NaBH₄ and 0.25 M KOH to generate stannane gas. The mixture was delivered continuously to a gas/liquid separator and the stannane gas was introduced into a Perkin-Elmer Sciex Elan 6000 ICP-MS for concentration measurements. A method detection limit of 0.45 mg/kg was sufficient for Sn levels commonly found in soil samples. Sn concentrations as low as 2.5 mg/kg were reproducibly measured in soil samples. Sample results by HG-ICP-MS agreed within ±17% relative difference to results by instrumental neutron activation analysis (INAA) and within ±6% relative difference to results by KOH fusion followed by inductively coupled plasma optical emission spectroscopy (ICP-OES).     

Determination of As, Sb, Bi and Hg in water samples by flow-injection inductively coupled plasma mass spectrometry with an in-situ nebulizer/hydride generator

A simple and very inexpensive in-situ nebulizer/hydride generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of As, Sb, Bi and Hg in water samples. The application of hydride generation ICP-MS alleviated the sensitivity problem of As, Sb, Bi and Hg determinations encountered when the conventional pneumatic nebulizer was used for sample introduction. The sample was introduced by flow injection to minimize the deposition of solids on the sampling orifice. The elements in the sample were reduced to the lower oxidation states with L-cysteine before being injected into the hydride generation system. This method has a detection limit of 0.003, 0.003, 0.017 and 0.17 ng ml⁻¹ for As, Bi, Sb and Hg, respectively. This method was applied to determine As, Sb, Bi and Hg in a CASS-3 nearshore seawater reference sample, a SLRS-2 riverine water reference sample and a tap water collected from National Sun Yat-Sen University. The concentrations of the elements were determined by standard addition method. The precision was better than 20% for most of the determinations.     

Optimization of selenium determination in plant samples by hydride generation and axial view inductively coupled plasma atomic emission spectrometry

The use of hydride generation coupled with axial view inductively couple plasma atomic emission spectrometry was presented for the determination of selenium in plant samples. The chemical factors affecting potentially the hydride generation efficiency (hydrochloric acid, sodium borohydride and sodium hydroxide concentrations) were assessed through investigation of chemical interference, accuracy and repeatability. The accuracy of measurements was not affected by elements present in high concentration in the plant matrix (K, Ca, Mg, and P). No interference was also observed with transition metals. Using a real sample (maize) with standard additions, decreases of recoveries were sometimes observed for 0.1% (m/v) NaOH, and attained 13.8% in the most unfavourable case. The final accuracy of the method was verified by using two certified reference materials: CRM 402 (white clover) and CRM 279 (sea lettuce). No statistically significant differences were obtained between the measured concentrations and the certified values. The optimized method was found sensitive (detection limit 0.15 μg l⁻¹), reliable and repeatable (R.S.D. between 1.3% and 4.0%).     

Determination of trace lead by hydride generation-inductively coupled plasma-mass spectrometry

A newly developed hydride generation-inductively coupled plasma-mass spectrometry (HG-ICP-MS) system was employed to determine trace amounts of lead in geological and biological samples. Laboratory-made single-stage and double-stage gas-liquid separators (GLSs) were investigated in order to replace the consumable membrane-GLS. Possible reasons were given why double-stage GLSs were superior over the single-stage ones according to the factors such as GLS volume and configuration, carrier gas inlet mode and flow rate. Interferences in liquid and vapor phase from concomitant ions and their products were investigated employing different flow mani-folds. Memory effects contributed to the blank values, but could be reduced employing a special wash protocol. Internal and external standardization were combined to improve the accuracy of the method, with bismuth as the internal standard according to its similarity with lead in the HG-ICP-MS system. Compared with ICP-MS and hydride generation-atomic fluorescence spectrometry (HG-AFS) methods, the system performance of HG-ICP-MS was characterized with improved detection limit to 0.002 ng/ml and acceptable short- and long-term stabilities. The linear dynamic range of this method was up to 50 ng/ml lead. Three Chinese national certified reference materials: poplar leaves, human hair and copper ore, were analyzed for method validation, and the results agreed well with the certified values. At last, the method was also employed to determine wide range of lead concentrations in lightweight limestone and nervous tissue samples from infants of albino rats with recoveries between 95 and 105% (n=10).     

顺序注射氢化物发生-原子荧光光谱法同时测定硒和砷的研究

建立了一种顺序注射氢化物发生-原子荧光光谱法测定试样中Se和As的方法,同时讨论了共存离子的干扰情况.在最佳实验条件下,Se和As的检出限分别为0.16和0.095 μg/L,加标回收率为92.4%～104.7%.     

The determination of antimony and arsenic concentrations in fly ash by hydride generation inductively coupled plasma optical emission spectrometry

Hydride generation inductively coupled plasma optical emission spectrometry (HG-ICP-OES) was used in the determination of As and Sb concentrations in fly ash samples. The effect of sample pre-treatment reagents and measurement parameters used for hydride generation was evaluated. Due to memory effects observed, the appropriate read delay time was adjusted to 60 s resulting in RSDs 0.6% and 2.3% for As and Sb, respectively. The most suitable volumes of pre-reduction reagents for 10 mL of sample were 4 mL of KI/ascorbic acid (5%) and 6 mL of HCl (conc.). The determination of Sb was significantly interfered by HF, but the interference could be eliminated by adding 2 mL of saturated boric acid and heating the samples to 60 °C at least 45 min. The accuracy of the method was studied by analyses of SRM 1633b and two fly ash samples with the recovery test of added As and Sb. As high a recovery as 96% for SRM 1633b was reached for As using 193.696 nm with two-step ultrasound-assisted digestion. A recovery rate of 103% was obtained for Sb using 217.582 nm and the pre-reduction method with the addition of 2 mL of saturated boric acid and heating. The quantification limits for the determination of As and Sb in the fly ash samples using two-step ultrasound-assisted digestion followed with HG-ICP-OES were 0.89 and 1.37 mg kg⁻¹, respectively.