Synthesis and characterization of lithium manganese oxides with core-shell Li4Mn5O12@Li2MnO3 structure as lithium battery electrode materials

By a facile LiNO₃ flux method, lithium manganese oxide composites (xLi₄Mn₅O₁₂? yLi₂MnO₃) were synthesized using a hierarchical organization precursor of manganese dioxide. Li₄Mn₅O₁₂ and Li₂MnO₃ have spinel and rocksalt structures, respectively. The lithiation and structural transformation from the precursor to the composites occurred topotactically from exterior toward interior in the precursor particle with the increase of reaction time, and the composites had core-shell spinel@rocksalt structures in addition to the original hierarchical core-shell organization. The electrochemical measurements at 50 °C after 50 cycles confirmed that a typical spinel@rocksalt cathode had higher capacity retention (87.1%) than that with the composition close to the stoichiometric spinel (64.6%), indicating the Li₂MnO₃ shell can improve cycling stability for the composite electrode at elevated temperature.     

Synthesis of Manganese Oxide Microspheres by Ultrasonic Spray Pyrolysis and Their Application as Supercapacitors

Manganese oxide (MnO₂) microspheres are prepared using an ultrasonic spray pyrolysis (USP) process. A mixed solution of potassium permanganate and hydrochloric acid is nebulized into microsized droplets, which are then carried by air flow through a furnace tube. Each microdroplet serves as one microreactor and produces one microsphere. Upon heating, KMnO₄ is decomposed into MnO₂ microspheres; this synthetic process can easily be scaled up. Characterization of the MnO₂ microspheres by scanning electron microscopy, transmission electron microscopy, powder X‐ray diffraction, Raman spectroscopy, and X‐ray photoelectron spectra is described. Different morphologies of MnO₂ microspheres can be controlled by tuning the precursor concentrations (and ratios) and furnace temperatures. Microspheres synthesized at 150 °C give amorphous MnO₂ while synthesis at 500 °C yields crystalline α‐MnO₂. The electrochemical properties investigated by cyclic voltammetry give specific capacitance as high as 320 F g^?1, demonstrating promising properties as supercapacitors. In addition, these microspheres can be directly sprayed on conductive substrates, such as carbon fiber paper, and may have useful applications as a supercapacitor electrode coating. The supercapacitive properties of MnO₂ microspheres at higher charge and discharge rates can be improved by increasing the surface area coverage or coating them with a thin layer of conductive polymer.     

Chemical state of the surface of mechanically activated Mn<Subscript><Emphasis Type="Italic">m</Emphasis></Subscript>O<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript> oxides

X-ray photoelectron spectroscopy is used to study Mn₃O₄, Mn₂O₃, and MnO₂ manganese oxide surfaces subjected to mechanical activation by means of high intensity grinding. It is found that Mn₂O₃ is the most thermodynamically stable of these oxides; mechanical activation converts the surface layers of Mn₃O₄ and MnO₂ into this intermediate oxide. The chemical stability of activated Mn₂O₃ with respect to actions of the environment was considerably elevated. This result is explained in terms of features of the structural state of the mechanically activated surface.     

Micro‐Raman investigation of transition‐metal‐doped ZnO nanoparticles

We measured the Raman spectra of ZnO nanoparticles (ZnO‐NPs), as well as transition‐metal‐doped (5% Mn(II), Fe(II) or Co(II)) ZnO nanoparticles, with an average size of 9 nm. A typical Raman peak at 436 cm⁻¹ is observed in the ZnO‐NPs, whereas Zn_1−xMn_xO, Zn_1−xFe_xO and Zn_1−xCo_xO presented characteristic peaks at 661, 665 and 675 cm⁻¹, respectively. These peaks can be related to the formation of Mn₃O₄, Fe₃O₄ and Co₃O₄ species in the doped ZnO‐NPs. Moreover, these samples were analyzed at various laser powers. Here, we observed new vibrational modes (512, 571 and 528 cm⁻¹), which are specific to Mn, Fe and Co dopants, respectively, and ZnO‐NPs did not reveal any additional modes. The new peaks were interpreted either as disorder activated phonon modes or as local vibrations of Mn‐, Fe‐ and Co‐related complexes in ZnO. Copyright © 2007 John Wiley & Sons, Ltd.     

Yolk–Shell‐Structured Cu/Fe@γ‐Fe2O3 Nanoparticles Loaded Graphitic Porous Carbon for the Oxygen Reduction Reaction

Core–shell Cu/γ‐Fe₂O₃@C and yolk–shell‐structured Cu/Fe@γ‐Fe₂O₃@C particles are prepared by a facile synthesis method using copper oxide as template particles, resorcinol‐formaldehyde as the carbon precursor, and iron nitrate solution as the iron source via pyrolysis. With increasing carbonization temperature and time, solid γ‐Fe₂O₃ cores are formed and then transformed into Fe@γ‐Fe₂O₃ yolk–shell‐structured particles via Ostwald ripening under nitrogen gas flow. The composition variations are studied, and the formation mechanism is proposed for the generation of the hollow and yolk–shell‐structured metal and metal oxides. Moreover, highly graphitic carbons can be obtained by etching the metal and metal oxide nanoparticles through an acid treatment. The electrocatalytic activity for oxygen reduction reaction is investigated on Cu/γ‐Fe₂O₃@C, Cu/Fe@γ‐Fe₂O₃@C, and graphitic carbons, indicating comparable or even superior performance to other Fe‐based nanocatalysts.     

Magnetically‐Confined Fe‐Mn Bimetallic Oxide Encapsulation as an Efficient and Recoverable Adsorbent for Arsenic(III) Removal

Synthesis of bimetallic‐oxide‐encapsulated magnetic nanoparticles is still significantly challenging and has rarely been attempted previously, due to the effects of lattice mismatch, weak chemical interactions and variances in growth rates between different components, as well as the difficulty in process control for uniform co‐deposition. In the present work, Fe‐Mn bimetallic oxide (FMBO) nanoplatelet encapsulated magnetic nanoparticles (Mag‐FeMn) are prepared by controlled engineering of the interparticle coupling of Fe₃O₄ and FMBO, with its multifunctional capabilities highlighted in terms of the potentially superior As(III) sequestration and convenient recoverability. Multiple characterization techniques are employed to examine the derived morphologies and to accurately resolve both compositionally and magnetically the hierarchical structure in detail. The synthesized magnetic composites retain highly porous structure with the main components of Fe₂O₃, FeOOH, Fe₃O₄, and Mn₃O₄. Mag‐FeMn exhibits a quite competitive high capacity for As(III) capture (56.1 mg g^–1), whereby As(III) oxidation coupled with synchronous sorption contributes to the improved performance. The unique heterostructure of FMBO encapsulation with an embedded magnetic core would be applicable to help with rational synthesis of other bimetallic oxide encapsulated magnetic nanoparticles, and definitely shows promise for the development of new nanotechnology enabled approaches for adsorption‐based water purification.     

Plasmonics properties of trimetallic Al@Al2O3@Ag@Au and Al@Al2O3@AuAg nanostructures

Bimetallic and trimetallic nanoparticles have attracted significant attention in recent times due to their enhanced electrochemical and catalytic properties compared to monometallic nanoparticles. The numerical calculations using Mie theory has been carried out for three-layered metal nanoshell dielectric–metal–metal (DMM) system consisting of a particle with a dielectric core (Al@Al₂O₃), a middle metal Ag (Au) layer and an outer metal Au (Ag) shell. The results have been interpreted using plasmon hybridization theory. We have also prepared Al@Al₂O₃@Ag@Au and Al@Al₂O₃@AgAu triple-layered core–shell or alloy nanostructure by two-step laser ablation method and compared with calculated results. The synthesis involves temporal separations of Al, Ag, and Au deposition for step-by-step formation of triple-layered core–shell structure. To form Al@Ag nanoparticles, we ablated silver for 40 min in aluminium nanoparticle colloidal solution. As aluminium oxidizes easily in water to form alumina, the resulting structure is core–shell Al@Al₂O₃. The Al@Al₂O₃ particle acts as a seed for the incoming energetic silver particles for multilayered Al@Al₂O₃@Ag nanoparticles is formed. The silver target was then replaced by gold target and ablation was carried out for different ablation time using different laser energy for generation of Al@Al₂O₃@Ag@Au core–shell or Al@Al₂O₃@AgAu alloy. The formation of core–shell and alloy nanostructure was confirmed by UV–visible spectroscopy. The absorption spectra show shift in plasmon resonance peak of silver to gold in the range 400–520 nm with increasing ablation time suggesting formation of Ag–Au alloy in the presence of alumina particles in the solution.     

Facile Synthesis of Gd(OH)3‐Doped Fe3O4 Nanoparticles for Dual‐Mode T1‐ and T2‐Weighted Magnetic Resonance Imaging Applications

The facile hydrothermal synthesis of polyethyleneimine (PEI)‐coated iron oxide (Fe₃O₄) nanoparticles (NPs) doped with Gd(OH)₃ (Fe₃O₄‐Gd(OH)₃‐PEI NPs) for dual mode T₁‐ and T₂‐weighted magnetic resonance (MR) imaging applications is reported. In this approach, Fe₃O₄‐Gd(OH)₃‐PEI NPs are synthesized via a hydrothermal method in the presence of branched PEI and Gd(III) ions. The PEI coating onto the particle surfaces enables further modification of poly(ethylene glycol) (PEG) in order to render the particles with good water dispersibility and improved biocompatibility. The formed Fe₃O₄‐Gd(OH)₃‐PEI‐PEG NPs have a Gd/Fe molar ratio of 0.25:1 and a mean particle size of 14.4 nm and display a relatively high r₂ (151.37 × 10^?3m ^?1 s^?1) and r₁ (5.63 × 10^?3m ^?1 s^?1) relaxivity, affording their uses as a unique contrast agent for T₁‐ and T₂‐weighted MR imaging of rat livers after mesenteric vein injection of the particles and the mouse liver after intravenous injection of the particles, respectively. The developed Fe₃O₄‐Gd(OH)₃‐PEI‐PEG NPs may hold great promise to be used as a contrast agent for dual mode T₁‐ and T₂‐weighted self‐confirmation MR imaging of different biological systems.     

Investigation on the electrochemical performances of Li<Subscript>4</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript> for battery applications

In this study, well-crystallized Li₄Mn₅O₁₂ powder was synthesized by a self-propagating combustion method using citric acid as a reducing agent. Various conditions were studied in order to find the optimal conditions for the synthesis of pure Li₄Mn₅O₁₂. The precursor obtained was then annealed at different temperatures for 24 h in a furnace. X-ray diffraction results showed that Li₄Mn₅O₁₂ crystallite is stable at relatively low temperature of 400 °C but decompose to spinel LiMn₂O₄ and monoclinic Li₂MnO₃ at temperatures higher than 500 °C. The prepared samples were also characterized by FESEM and charge-discharge tests. The result showed that the specific capacity of 70.7 mAh/g was obtained within potential range of 4.2 to 2.5 V at constant current of 1.0 mA. The electrochemical performances of Li₄Mn₅O₁₂ material was further discussed in this paper.     

Synthesis of MnO2 nanoparticles from sonochemical reduction of MnO4− in water under different pH conditions

MnO₂ was synthesized by sonochemical reduction of MnO₄⁻ in water under Ar atmosphere at 20 °C, where the effects of solution pH on the reduction of MnO₄⁻ were investigated. The obtained XRD results showed that poor crystallinity δ-MnO₂ was formed at pH 2.2, 6.0 and 9.3. When solution pH was increased from 2.2 to 9.3, the morphologies of δ-MnO₂ changed from aggregated sheet-like or needle-like structures to spherical nanoparticles and finally to cubic or polyhedron nanoparticles. After further irradiation, MnO₂ was readily reduced to Mn²⁺. It was confirmed that H₂O₂ and H atoms formed in the sonolysis of water acted as reductants for both reduction for MnO₄⁻ to MnO₂ and MnO₂ to Mn²⁺. The optimum irradiation time for the effective synthesis of MnO₂ was 13 min at pH 2.2, 9 min at pH 6.0, 8 min at pH 9.3, respectively.     

General Synthesis and Lithium Storage Properties of Metal Oxides/MnO2 Hierarchical Hollow Hybrid Spheres

Metal oxides/MnO₂ hierarchical hollow hybrid nanostructures have attracted significant attention because of their wide potential applications. However, the exploration of a general synthetic approach for fabricating hierarchical hollow hybrid nanostructures is still a great challenge. Herein, a “penetration‐carbonization and reduction‐coating–annealing” route is presented for the generalized synthesis of metal oxides/MnO₂ hierarchical hollow hybrid spheres, including NiO/MnO₂, Co₃O₄/MnO₂, and CuO/MnO₂. Because of the unique hierarchical hollow hybrid nanostructures, NiO/MnO₂ nanomaterials possess a desirable capacity (1520 mA h g⁻¹) and outstanding cyclic stability (909 mA h g⁻¹ at the 200th cycle) as Li‐ion battery anode materials. The work reported herein can not only pave the way for the generalized synthetic strategy of metal oxides/MnO₂ hierarchical hollow hybrid nanostructures, but also provide a promising application of NiO/MnO₂ nanomaterials for Li‐ion battery anode.     

A study of modified Fe3O4 nanoparticles for the synthesis of ionic ferrofluids

XRD and XPS analyses revealed that a Fe(NO₃)₃·9H₂O layer formed outside γ-Fe₂O₃ particles when Fe₃O₄ nanoparticles were treated with ferric nitrate. The particle density differed for untreated and treated particles and was not uniform for the latter. The specific saturation magnetization of both treated and untreated particles was used to estimate the thickness of the Fe(NO₃)₃·9H₂O layer and the average density of the treated particles. The density of the treated particles was used to calculate the density of ferrofluids of different particle volume fractions. These values are in agreement with measured results. Therefore, the particle volume fraction can be designed to synthesize acid ionic ferrofluids based on Fe₃O₄ nanoparticles using Massart's method.     

Surface-modified Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript> nanoparticles with LaF<Subscript>3</Subscript> as cathode for Li-ion battery

The LaF₃-coated Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ nanoparticles were synthesized via co-precipitation method followed by simple chemical deposition process. The crystal structure, particle morphology, and electrochemical properties of the bare and coated materials were studied by XRD, SEM, TEM, charge–discharge tests. The results showed that the surface coating on Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ nanoparticles were amorphous LaF₃ layer with a thickness of about 10–30 nm. After the surface modification with LaF₃ films, the coating layer served as a protective layer to suppress the side reaction between the positive electrode and electrolyte, and the Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ oxide demonstrated the improved electrochemical properties. The LaF₃-coated Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ electrode delivered the capacities of 270.5, 247.9, 197.1, 170.0, 142.7, and 109.5 mAh g^?1 at current rates of 0.1, 0.2, 0.5, 1, 2, and 5 C rate, respectively. Besides, the capacity retention was increased from 85.1 to 94.8 % after 100 cycles at 0.5 C rate. It implied surface modification with LaF₃ played an important role to improve the cyclic stability and rate capacity of the Li-rich nickel manganese oxides.     

Synthesis of tailored WO3 and WOx (2.9 < x < 3) nanoparticles by adjusting the combustion conditions in a H2/O2/Ar premixed flame reactor

Flame synthesis of WO₃ and WO_x (2.9 < x < 3) nanoparticles is carried out by adding a dilute concentration of WF₆ as precursor in a low-pressure H₂/O₂/Ar premixed flame reactor. The reactor is equipped with molecular-beam sampling and particle mass spectroscopy (PMS) to determine particle composition and sizes as a function of height above burner. Varying the H₂/O₂ ratio allowed us to tune the stoichiometry of the product. With a H₂/O₂ ratio of 0.67 white colored stoichiometric WO₃ is formed, whereas the H₂/O₂ ratio >0.8 yields blue colored non-stoichiometric WO_x (2.9 < x < 3) nanoparticles. The size of nanoparticles can be controlled by varying the residence time in the high-temperature zone of the reactor as observed by molecular-beam sampling with subsequent analysis using PMS. Transmission electron microscopy (TEM) images of as-synthesized nanoparticles show that particles are non-agglomerated and have an almost spherical morphology. The X-ray diffraction (XRD) pattern of the as-synthesized material indicates that the powders exhibit poor crystallinity, however, subsequent thermal annealing of the sample in air changes its structure from amorphous to crystalline phase. It is observed that particles with sub-stoichiometric composition (WO_x) show higher conductivity compared to the stoichiometric WO₃ sample.     

Controlled flame synthesis of αFe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles: effect of flame configuration,flame temperature,and additive loading

Superparamagnetic iron oxide nanoparticles are used in diverse applications, including optical magnetic recording, catalysts, gas sensors, targeted drug delivery, magnetic resonance imaging, and hyperthermic malignant cell therapy. Combustion synthesis of nanoparticles has significant advantages, including improved nanoparticle property control and commercial production rate capability with minimal post-processing. In the current study, superparamagnetic iron oxide nanoparticles were produced by flame synthesis using a coflow flame. The effect of flame configuration (diffusion and inverse diffusion), flame temperature, and additive loading on the final iron oxide nanoparticle morphology, elemental composition, and particle size were analyzed by transmission electron microscopy (TEM), high-resolution TEM (HR-TEM), energy dispersive spectroscopy (EDS), and Raman spectroscopy. The synthesized nanoparticles were primarily composed of two well known forms of iron oxide, namely hematite αFe₂O₃ and magnetite Fe₃O₄. We found that the synthesized nanoparticles were smaller (6–12 nm) for an inverse diffusion flame as compared to a diffusion flame configuration (50–60 nm) when CH₄, O₂, Ar, and N₂ gas flow rates were kept constant. In order to investigate the effect of flame temperature, CH₄, O₂, Ar gas flow rates were kept constant, and N₂ gas was added as a coolant to the system. TEM analysis of iron oxide nanoparticles synthesized using an inverse diffusion flame configuration with N₂ cooling demonstrated that particles no larger than 50–60 nm in diameter can be grown, indicating that nanoparticles did not coalesce in the cooler flame. Raman spectroscopy showed that these nanoparticles were primarily magnetite, as opposed to the primarily hematite nanoparticles produced in the hot flame configuration. In order to understand the effect of additive loading on iron oxide nanoparticle morphology, an Ar stream carrying titanium-tetra-isopropoxide (TTIP) was flowed through the outer annulus along with the CH₄ in the inverse diffusion flame configuration. When particles were synthesized in the presence of the TTIP additive, larger monodispersed individual particles (50–90 nm) were synthesized as observed by TEM. In this article, we show that iron oxide nanoparticles of varied morphology, composition, and size can be synthesized and controlled by varying flame configuration, flame temperature, and additive loading.     

Preparation of magnetic nanoparticles by pulsed plasma chemical vapor synthesis

FePt nanoparticle is expected as a candidate for the magnetic material of the high density recording media. We attempted to synthesize FePt alloy nanoparticles using 13.56 MHz glow discharge plasma with the pulse operation of a square-wave on/off cycle of plasma discharge to control the size of nanoparticles. Vapors of metal organics, Biscyclopentadienyl iron (ferrocene) for Fe and (Methylcyclopentadienyl) trimethyl platinum for Pt, were introduced into the capacitively coupled flow-through plasma chamber, which consisted of shower head RF electrode and grounded mesh electrode. Synthesis experiments were conducted at room temperature under the conditions of pressure 0.27 Pa, source gas concentration 0.005 Pa, gas residence time 0.5 s and plasma powers 60 watts. Pulse width for plasma duration was chosen from 0.5 to 30 s and plasma off period was 4 s to each pulse operation. Visual observations during the particle growth showed plasma emission in the bulk region was increased with the particle growth. These were theoretically explained by using the model for both transient particle charging in the plasma and single particle behavior in the stationary plasma as well as assuming the similarity between the negative charged particle and negative gas containing plasma. Synthesized nanoparticles were directly collected onto TEM grid, which was placed just below the grounded mesh electrode in the plasma reactor downstream. TEM pictures showed two kinds of particles in size, one of which was nanometer size and isolated with crystal structures and the other appeared agglomerate of nanometer size particles. The size of agglomerated particle was controlled in the 10–120 nm range by varying the plasma-on time from 0.5 to 30 s, although the nanometer size particles did not change. The composition of FePt alloy particles could be altered by adjusting the source gas feed ratio. Also magnetization of FePt nanoparticles was measured by use of SQUID (superconducting quantum interference device) magnetometry measurements. As-synthesized FePt nanoparticles did not exhibit loop-shape characteristic, which indicated superpamagnetic property. Annealed nanoparticles with the composition of Fe₅₈Pt₄₂ at 650°C in atmospheric hydrogen showed clear hysterisis loop with the coercivity as large as 10 KOe.     

Interparticle interaction effects on magnetic behaviors of hematite (α-Fe2O3) nanoparticles

The interparticle magnetic interactions of hematite (α-Fe₂O₃) nanoparticles were investigated by temperature and magnetic field dependent magnetization curves. The synthesis were done in two steps; milling metallic iron (Fe) powders in pure water (H₂O), known as mechanical milling technique, and annealing at 600 °C. The crystal and molecular structure of prepared samples were determined by X-ray powder diffraction (XRD) spectra and Fourier transform infrared (FTIR) spectra results. The average particle sizes and the size distributions were figured out using transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The magnetic behaviors of α-Fe₂O₃ nanoparticles were analyzed with a vibrating sample magnetometer (VSM). As a result of the analysis, it was observed that the prepared α-Fe₂O₃ nanoparticles did not perform a sharp Morin transition (the characteristic transition of α-Fe₂O₃) due to lack of unique particle size distribution. However, the transition can be observed in the wide temperature range as “a continuously transition”. Additionally, the effect of interparticle interaction on magnetic behavior was determined from the magnetization versus applied field (σ(M)) curves for 26±2 nm particles, dispersed in sodium oxalate matrix under ratios of 200:1, 300:1, 500:1 and 1000:1. The interparticle interaction fields, recorded at 5 K to avoid the thermal interactions, were found as ∼1082 Oe for 26±2 nm particles.     

Carbon‐Encapsulated Tube‐Wire Co3O4/MnO2 Heterostructure Nanofibers as Anode Material for Sodium‐Ion Batteries

This study presents a general approach for the synthesis of carbon‐encapsulated wire‐in‐tube Co₃O₄/MnO₂ heterostructure nanofibers (Co₃O₄/MnO₂@C) via electrospinning followed by calcination. The as‐synthesized Co₃O₄/MnO₂@C is investigated as the sodium‐ion batteries anode material, which not only exhibits a high reversible capacity of 306 mAh g⁻¹ at 100 mA g⁻¹ over 200 cycles, but also shows a cycling stability of 126 mAh g⁻¹ after 1000 cycles at a high current density of 800 mA g⁻¹. The excellent electrochemical performance can be ascribed to the contribution from carbon‐encapsulated outer‐tube Co₃O₄ and inner‐wire MnO₂ heterostructures, which offer a large internal space and good electrical conductivity. The present work can be helpful in providing new insights into heterostructures for sodium‐ion batteries and other applications.     

Wet chemical synthesis and characterization of pure and cerium doped Dy2O3 nanoparticles

Pure and cerium doped Dy₂O₃ nanoparticles were prepared by wet chemical synthesis route. The particles were subjected to thermal, structural, morphological and optical property studies. The calcination temperature was chosen based on the decomposition of the samples revealed by TG studies. EDS and FTIR results confirmed the presence of cerium in the Dy₂O₃ system. The particle size calculated from Williamson-Hall plot was consistent with TEM results. The effect of cerium as a dopant on the UV–vis absorption and photoluminescence intensity has been studied. XRD and PL analyses demonstrate that the cerium ions uniformly substitute dysprosium sites in Dy₂O₃ lattice and hence influence the optical properties.     

Electrochemical reaction of 5 V cathode LiNi0.4Mn1.6O4

LiNi_0.4Mn_1.6O₄ was prepared under air and oxygen atmospheres using fine Mn₃O₄ particle and large MnO₂ particle at various temperatures. The sample prepared from Mn₃O₄ at 750 °C under air or oxygen atmosphere exhibited an ideal electrochemical behavior, which was based on three redox couples of Mn³⁺/Mn⁴⁺, Ni²⁺/Ni³⁺, and Ni³⁺/Ni⁴⁺. On the other hand, the sample prepared from MnO₂ had a larger capacity at 4 V plateau and smaller one at 5 V plateau. However, when using oxygen atmosphere, the sample exhibited more ideal behavior, which is similar to the sample prepared from Mn₃O₄. This means that some defects exist in LiNi_0.4Mn_1.6O₄, depending on preparation conditions. In order to confirm this point, the chemical composition and the valence state of Mn of the prepared sample was analyzed. From these results, it can be said that electrochemical reactions of LiNi_0.4Mn_1.6O₄ are well explained based on three redox couples of Mn³⁺/Mn⁴⁺, Ni²⁺/Ni³⁺, and Ni³⁺/Ni⁴⁺ by considering a presence of oxygen defects.