Capillary electrochromatography–mass spectrometry determination of melamine and related triazine by-products using poly(divinyl benzene-alkene-vinylbenzyl trimethylammonium chloride) monolithic stationary phases

In this study, a capillary electrochromatography (CEC) method coupled either with UV or mass spectrometric detection was developed for the detection of trace-amounts of melamine and its related by-products (ammeline, ammelide, and cyanuric acid). A series of poly(divinyl benzene-alkene-vinylbenzyl trimethylammonium chloride) monolithic columns, which were prepared by a simple in situ polymerization with divinyl benzene (DVB), vinylbenzyl trimethylammonium chloride (VBTA) and different types of alkene monomers such as 1-octene, 1-dodecene or 1-octadecene were used as separation columns, with the poly(DVB-1-dodecene-VBTA) monolith as the optimal chromatographic material because it provided a better separation. The detection limits of four melamine derivatives were in the ranged of 0.6–2.18 mg L⁻¹ by the optimal CEC–UV mode, and were reduced from 2.2 to 19.4 μg L⁻¹ by the optimal CEC–MS mode. Finally, the proposed CEC methods successfully determined melamine contaminations (0.1 mg L⁻¹ per analyte) in several dairy products as test samples with analyte recovery range of 69–85% (intra-day) and 68–75% (inter-day), and with peak area reproducibility range of 4.3–8.6% and 8.7–15.6% for intra-day and inter-day, respectively. This is the first report for CEC separation coupled with MS detection applied in trace melamine residue analyses with a faster separation and comparable or even better detection ability than previous GC–MS, CE–MS, as well as LC–MS methods.     

Novel fabrication of on-column capillary inlet frits through flame induced sintering of stainless steel particles

A novel fritting technology was introduced for the fused-silica capillary. The technique involved sintering of stainless steel (SS) particles at the tip of capillary through flame heating. A simple butane gas based welding torch was used for sintering the SS particles. The new fritting technique, flame induced sintering of SS particles (FIS/SSP), was applied for making frits with different inlet diameters (75 μm, 100 μm, 250 μm and 530 μm). The changes in morphologies of SS particles during sintering process were identified by scanning electron microscopy (SEM). Frits with the length of 0.5-1 mm and capillaries with inner diameter about 50-100 μm were fabricated through suitable selection of experimental conditions (size of SS particles and heating mode). The frits prepared by FIS/SSP technique exhibited adequate separation properties and mechanical strength. Columns packed with C₁₈ particles were stable with these frits in a few important chromatographic operations. Frits prepared by FIS/SSP technique was used in three typical separation modes namely, capillary electrochromatography (CEC), p-assisted CEC (p-CEC) and low pressure liquid chromatography (LPLC). Importantly, no bubble formation was noticed with the frit over a period of one week. A good peak symmetry and high efficiency for separation were obtained using pressure-assisted CEC, p-CEC and low pressure-driven separation modes.     

Semi-micro-monolithic columns using macroporous silica rods with improved performance

Monolithic silica columns in semi-micro-format have been synthesized using poly(acrylic acid) as a phase-separation inducer via a sol–gel route. The absence of a thick skin layer accompanied by deformation of the micrometer-sized gelling skeletons on the outermost part of the macroporous silica rod contributed to improve the efficiency of monolithic silica columns as thick as 2.4 mm in diameter. The kinetic plot analysis revealed that monolithic silica columns with macropore diameter of 1 μm and skeleton thickness of 1 μm with decreased macroporosity behave similarly to columns packed with 3 μm particles with slightly lower back pressure.     

Multi-residue method for the determination of organochlorine pesticides in fish feed based on a cleanup approach followed by gas chromatography–triple quadrupole tandem mass spectrometry

A multi-residue method for the determination of organochlorine pesticides in fish feed samples was developed and optimized. The method is based on a cleanup step of the extracted fat, carried out by liquid–liquid extraction on diatomaceous earth cartridge with n-hexane/acetonitrile (80/20, v/v) followed by solid phase extraction (SPE) with silica gel–SCX cartridge, before the identification and quantification of the residues by gas chromatography–triple quadrupole tandem spectrometry (GC–MS/MS). Performance characteristics, such as accuracy, precision, linear range, limits of detection (LOD) and quantification (LOQ), for each pesticide were determined. Instrumental LODs ranged from 0.01 to 0.11 μg L⁻¹, LOQs were in the range of 0.02–0.35 μg L⁻¹, and calibration curves were linear (r² > 0.999) in the whole range of explored concentrations (5–100 μg L⁻¹). Repeatability values were in the range of 3–15%, evaluated from the relative standard deviation of six samples spiked at 100 μg kg⁻¹ of fat, and in compliance with that derived by the Horwitz's equation. No matrix effects or interfering substances were observed in fish feed analyses. The proposed method allowed high recoveries (92–116%) of spiked extracted fat samples at 100 μg kg⁻¹, and very low LODs (between 0.02 and 0.63 μg kg⁻¹) and LOQs (between 0.05 and 2.09 μg kg⁻¹) determined in fish feed samples.     

Large-scale pesticide testing in olives by liquid chromatography–electrospray tandem mass spectrometry using two sample preparation methods based on matrix solid-phase dispersion and QuEChERS

In this work we have evaluated the performance of two sample preparation methodologies for the large-scale multiresidue analysis of pesticides in olives using liquid chromatography–electrospray tandem mass spectrometry (LC–MS/MS). The tested sample treatment methodologies were: (1) liquid–liquid partitioning with acetonitrile followed by dispersive solid-phase extraction clean-up using GCB, PSA and C₁₈ sorbents (QuEChERS method – modified for fatty vegetables) and (2) matrix solid-phase dispersion (MSPD) using aminopropyl as sorbent material and a final clean-up performed in the elution step using Florisil. An LC–MS/MS method covering 104 multiclass pesticides was developed to examine the performance of these two protocols. The separation of the compounds from the olive extracts was achieved using a short C₁₈ column (50 mm × 4.6 mm i.d.) with 1.8 μm particle size. The identification and confirmation of the compounds was based on retention time matching along with the presence (and ratio) of two typical MRM transitions. Limits of detection obtained were lower than 10 μg kg⁻¹ for 89% analytes using both sample treatment protocols. Recoveries studies performed on olives samples spiked at two concentration levels (10 and 100 μg kg⁻¹) yielded average recoveries in the range 70–120% for most analytes when QuEChERS procedure is employed. When MSPD was the choice for sample extraction, recoveries obtained were in the range 50–70% for most of target compounds. The proposed methods were successfully applied to the analysis of real olives samples, revealing the presence of some of the target species in the μg kg⁻¹ range. Besides the evaluation of the sample preparation approaches, we also discuss the use of advanced software features associated to MRM method development that overcome several limitations and drawbacks associated to MS/MS methods (time segments boundaries, tedious method development/manual scheduling and acquisition limitations). This software feature recently offered by different vendors is based on an algorithm that associates retention time data for each individual MS/MS transition, so that the number of simultaneously traced transitions throughout the entire chromatographic run (dwell times and sensitivity) is maximized.     

Electrically assisted capillary liquid chromatography using a silica monolithic column

A silica monolithic capillary column was linked to an open capillary of the same internal diameter via a Teflon sleeve to form a duplex column to investigate the combination of chromatography and electrophoresis in the mode of electrically assisted capillary liquid chromatography (eCLC). Using a commercial CE instrument with an 8.5 cm long, 100 μm i.d. reversed phase silica monolithic section and a window 1.5 cm beyond the end of this in a 21.5 cm open section, a minimum plate height of 9 μm was obtained in capillary liquid chromatography (CLC) mode at a low driving pressure of 50 psi. In eCLC mode, high speed and high resolution separations of acidic and basic compounds were achieved with selectivity tuning based on the flexible combination of pressure (0–100 psi) and voltage. Taking advantage of the excellent permeability of silica monolithic columns, use of a step flow gradient enabled elution of compounds with different charge state.     

Improvement of solid phase microextraction fiber assembly and interface for liquid chromatography

Modifications were made on commercial SPME fiber assembly and SPME–LC interface to improve the applicability of SPME for LC. Polyacrylonitrile (PAN)/C18 bonded fuse silica was used as the fiber coating for LC applications because the fiber coating was not swollen in common LC solvents at room temperature. The inner tubing of SPME fiber assembly was replaced with a 457 μm outside diameter (o.d.) solid nitinol rod. And the coated fiber (o.d. 290 μm) was installed onto the nitinol rod. The inner diameter (i.d.) of the through hole of the ferrule in the SPME–LC interface was enlarged to 508 μm to accommodate the nitinol rod. The much larger inner rod protected the fiber coating from being stripped when the fiber was withdrawn from the SPME–LC interface. The system was evaluated in term of pressure test, desorption optimization, peak shape, carryovers, linear range, precision, and limit of detection (LOD) with polycyclic aromatic hydrocarbons (PAHs) as the test analytes. The results demonstrated that the improved system was robust and reliable. It overcame the drawbacks, such as leak of solvents and damage of fiber coatings, associated with current SPME fibers and SPME–LC interface. Another sealing mechanism was proposed by sealing the nitinol rod with a specially designed poly(ether ether ketone) (PEEK) fitting. The device was fabricated and tested for manual use.     

Use of multiple-reaction monitoring ratios for identifying incompletely resolved fentanyl homologs and analogs via ultra-high-pressure liquid chromatography–tandem mass spectrometry

Fentanyl and 16 of its corresponding homologs and analogs were distinguished using ultra-high-pressure liquid chromatography–tandem mass spectrometry (UHPLC–MS/MS). A 1.7 μm Acquity BEH C18 column (150 mm × 2.1 mm) was used with a 1% formic acid (pH 2.2), methanol gradient. Multiple-reaction monitoring (MRM) was employed for MS/MS detection. All selected fentanyl-related compounds, including incompletely resolved compounds, were uniquely identified using retention times and dual MRMs.     

Optimisation of a headspace-solid-phase micro-extraction method for simultaneous determination of organometallic compounds of mercury,lead and tin in water by gas chromatography–tandem mass spectrometry

In this work, a headspace-solid-phase micro-extraction (HS-SPME) combined with gas chromatography–mass spectrometry (GC–MS) method for multielemental speciation of organometallic compounds of mercury, lead and tin in water samples was upgraded by the introduction of tandem mass spectrometry (MS/MS) as detection technique. The analytical method is based on the ethylation with NaBEt₄ and simultaneous headspace-solid-phase micro-extraction of the derivative compounds followed by GC–MS/MS analysis. The main experimental parameters influencing the extraction efficiency such as derivatisation time, extraction time and extraction temperature were optimized. The overall optimum extraction conditions were the following: a 50 μm/30 μm divinyl-benzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) SPME fibre, 150 min derivatisation time, 15 min extraction time, sample agitation at 250 rpm and 40 °C extraction temperature. The analytical characteristics of the HS-SPME method combined with GC–MS and GC–MS/MS were evaluated. The combination of both techniques HS-SPME and GC–MS/MS allowed to attain lower limits of detection (4–33 ng l⁻¹) than those obtained by HS-SPME–GC–MS (17–45 ng l⁻¹). The proposed method presented good linear regression coefficients (r² > 0.9970) and repeatability (4.8–21.0%) for all the compounds under study. The accuracy of the method measured as the average percentage recovery of the compounds in spiked river water and seawater samples was higher than 80% for all the compounds studied, except for monobutyltin in the river water sample. A study of the uncertainty associated with the analytical results was also carried out.     

Validation and use of a fast sample preparation method and liquid chromatography–tandem mass spectrometry in analysis of ultra-trace levels of 98 organophosphorus pesticide and carbamate residues in a total diet study involving diversified food types

This paper reports a comprehensive sensitive multi-residue liquid chromatography–tandem mass spectrometry (LC–MS/MS) method for detection, identification and quantitation of 73 pesticides and their related products, a total of 98 analytes, belonging to organophosphorus pesticides (OPPs) and carbamates, in foods. The proposed method makes use of a modified QuEChERS (quick, easy, cheap, effective, rigged, and safe) procedure that combines isolation of the pesticides and sample clean-up in a single step. Analysis is performed by liquid chromatography-electrospray ionization–tandem mass spectrometry operated in the multiple reaction monitoring (MRM) mode, acquiring two specific precursor-product ion transitions per target compound. Two main fragment ions for each pesticide were obtained to achieve the identification according to the SANCO guidelines 10684/2009. The method was validated with various food samples, including edible oil, meat, egg, cheese, chocolate, coffee, rice, tree nuts, citric fruits, vegetables, etc. No significant matrix effect was observed for tested pesticides, therefore, matrix-matched calibration was not necessary. Calibration curves were linear and covered from 1 to 20 μg L⁻¹ for all compounds studied. The average recoveries, measured at 10 μg kg⁻¹, were in the range 70–120% for all of the compounds tested with relative standard deviations below 20%, while a value of 10 μg kg⁻¹ has been established as the method limit of quantitation (MLOQ) for all target analytes. Similar trueness and precision results were also obtained for spiking at 200 μg kg⁻¹. Expanded uncertainty values were in the range 21–27% while the HorRat ratios were below 1. The method has been successfully applied to the analysis of 700 food samples in the course of a baseline monitoring study of OPPs and carbamates.     

Magnetically immobilized frits for the preparation of packed columns used in capillary electrochromatography

Fabrication of porous frits to retain stationary phases is a critical issue in column preparation for capillary electrochromatography (CEC). In this work, porous frits were prepared by applying an external magnetic field to magnetically responsive particles placed inside a fused-silica capillary. Three batches of uniform magnetite spheres with particle diameters of 0.3, 0.4, and 0.6 μm and saturation magnetization values of 73.03, 74.41, and 77.83 emu/g, respectively, were used as frit particles and octadecyl- and phenyl-bonded silica gels were packed successfully into frit-containing capillaries. The performance of the resulting magnetically immobilized frits and packed columns was evaluated. The electroosmotic mobilities in capillaries containing outlet frit only were found to be reduced by 2–4% whereas the plate heights of an unretained marker increased by 30–50% as compared to those in open capillaries. These variations are believed to be associated with the inhomogeneities of the packed structure of the frits. The magnetically immobilized frits showed adequate mechanical strength to withstand the flow drag force, allowing separation in capillaries packed with 5-μm stationary phases up to 10–15 cm, thus rendering column efficiency and reproducibility comparable with those obtained with sintered frits. Taken together, retaining frits made of uniform magnetite particles serves as a viable alternative to sintered frits for column preparation, which offers several distinct advantages such as ease of preparation, improved durability as compared to sintered frits where the removal of the polyimide coating makes the packed column susceptible to breakage, and use of large-bore capillaries for semipreparative separations.     

Preparation of C18 composite solid-phase microextraction fiber and its application to the determination of organochlorine pesticides in water samples

In this work, a C18 composite solid-phase microextraction (SPME) fiber was prepared with a new method and applied to the analysis of organochlorine pesticides (OCPs) in water sample. A stainless steel wire (o.d. 127 μm) was used as the substrate, and a mixture of the C18 particle (3.5 μm) and the 184 silicone was used as the coating material. During the process of fiber preparation, a section of capillary column was used to fix the mixture onto the stainless steel wire and to ensure the constant of coating thickness. The prepared fiber showed excellent thermal stability and solvent resistance. By coupling with gas chromatography–mass spectrometry (GC–MS), the fiber exhibited wide linearity (2–500 ng L⁻¹) and good sensitivity for the determination of six OCPs in water samples, the OCPs tested included hexachlorobezene, trans-chlordane, cis-chlordane, o,p-DDT, p,p-DDT and mirex. Not only the extraction performance of the newly prepared fiber was more than seven times higher than those of commercial fibers, the limits of detections (LODs) (0.059–0.151 ng L⁻¹) for OCPs achieved under optimized conditions were also lower than those of reported SPME methods. The fiber was successfully applied to the determination of OCPs in real water samples by using developed SPME–GC–MS method.     

Method validation and comparison of acetonitrile and acetone extraction for the analysis of 169 pesticides in soya grain by liquid chromatography–tandem mass spectrometry

An acetonitrile-based extraction method for the analysis of 169 pesticides in soya grain, using liquid chromatography–tandem mass spectrometry (LC–MS/MS) in the positive and negative electrospray ionization (ESI) mode, has been optimized and validated. This method has been compared with our earlier published acetone-based extraction method, as part of a comprehensive study of both extraction methods, in combination with various gas chromatography–(tandem) mass spectrometry [GC–MS(/MS)] and LC–MS/MS techniques, using different detection modes. Linearity of calibration curves, instrument limits of detection (LODs) and matrix effects were evaluated by preparing standards in solvent and in the two soya matrix extracts from acetone and acetonitrile extractions, at seven levels, with six replicate injections per level. Limits of detection were calculated based on practically realized repeatability relative standard deviations (RSDs), rather than based on (extrapolated) signal/noise ratios. Accuracies (as % recoveries), precision (as repeatability of recovery experiments) and method limits of quantification (LOQs) were compared. The acetonitrile method consists of the extraction of a 2-g sample with 20 mL of acetonitrile (containing 1% acetic acid), followed by a partitioning step with magnesium sulphate and a subsequent buffering step with sodium acetate. After mixing an aliquot with methanol, the extract can be injected directly into the LC–MS/MS system, without any cleanup. Cleanup hardly improved selectivity and appeared to have minor changes of the matrix effect, as was earlier noticed for the acetone method. Good linearity of the calibration curves was obtained over the range from 0.1 or 0.25 to 10 ng mL⁻¹, with r² ≥ 0.99. Instrument LOD values generally varied from 0.1 to 0.25 ng mL⁻¹, for both methods. Matrix effects were not significant or negligible for nearly all pesticides. Recoveries were in the range 70–120%, with RSD ≤ 20%. If not, they were still mostly in the 50–70% range, with good precision (RSD ≤ 20%). The method LOQ values were most often 10 μg kg⁻¹ for almost all pesticides, with good repeatability RSDs. Apart from some minor pros and cons, both compared methods are fast, efficient and robust, with good method performances. The two methods were applied successfully in a routine analysis environment, during surveys in 2007 and 2008.     

Determination of eight penicillin antibiotics in pharmaceuticals,milk and porcine tissues by nano-liquid chromatography

This study describes the ability of nanoscale liquid chromatography (nano-LC) coupled with UV or mass spectrometry (MS) for the simultaneous determination of eight common penicillin antibiotics (amoxicillin, ampicillin, penicillin G, penicillin V, oxacillin, cloxacillin, nafcillin and dicloxacillin) in commercial samples (pharmaceuticals, milk, porcine tissues (liver and kidney)) for the first time. Material types of the on-column polymeric frits (polystyrene-based and polymethacrylate-based monoliths) and the packed stationary phase materials (C8 and C18 particles of 3 μm) used in the nano-LC for the influence of penicillin separation were evaluated. The nano-LC and MS parameters such as the composition and flow rate of mobile phase, capillary voltage and temperature of dry gas were examined in order to acquire high separation resolution and detection sensitivity for penicillin analyses. Furthermore, a home-made in-line filter (a nylon membrane of 0.2 μm pore size), was first used to connect with the flow cell of high sensitivity UV detector or the nanoelectrospray needle in MS detection. The result indicated it could effectively improve the reproducibility of penicillin mass signals or prolong the lifetime of the flow cell. The nano-LC methods provided good quantitative precisions in the range of 89.5–111.2% for UV detection at 0.5 μg/mL penicillins, and 83. 1–94.9% for MS detection at 5 μg/L penicillins), respectively, as well as offered stable retention repeatabilities (the relative standard deviation (RSD) of retention time was lower 0.30% in both the UV and MS detections). Compared to other LC–MS methods, the proposed nano-LC systems provided better detection sensitivity for these penicillins (the limits of detection (LOD) was of 2.27–4.06 μg/L for UV mode, and 0.01–0.51 μg/L for MS mode) when either UV or MS detector was employed.     

One step carbon nanotubes-based solid-phase extraction for the gas chromatographic–mass spectrometric multiclass pesticide control in virgin olive oils

This article presents a novel application of carbon nanotubes for the determination of pesticides (chlortoluron, diuron, atrazine, simazine, terbuthylazin-desethyl, dimetoathe, malathion and parathion) in virgin olive oil samples. For this purpose, two carbon nanotubes, multi-walled and carboxylated single-walled, were evaluated, the later being the most appropriate for the aim of the work. The sorbent (30 mg) was packed in 3-mL commercial cartridge and the virgin olive oil samples diluted (20%, v/v) in hexane were passed through it. After a washing step with 3 mL of hexane to remove the sample matrix, the pesticides were eluted with 500 μL of ethyl acetate. In order to achieve lower detection limits, the eluent was evaporated under a nitrogen stream and the residue reconstituted in 50 μL of the same solvent. Aliquots of 2 μL of the extract were directly injected into the GC–MS system for analysis. The low limits of detection achieved, between 1.5 and 3.0 μg L⁻¹, permit the application of the method to control the presence of these pollutants in very restrictive samples such as the ecological virgin olive oil. In addition to the sensitivity enhancement, the solid-phase extraction procedure is rather simple as it involves a single preconcentration–elution step, which allows sample processing in less than 8 min. Moreover, the cartridge can be reused at least 100 times without losing performance. The method was applied to the determination of the pesticides in two monovarietal and one ecologic commercial extra virgin olive oil samples. Two pesticides were detected in each of the monovarietal virgin olive oils while the ecological sample resulted to be a pesticide-free one.     

The performance of hybrid monolithic silica capillary columns prepared by changing feed ratios of tetramethoxysilane and methyltrimethoxysilane

The effect of a feed ratio of methyltrimethoxysilane (MTMS) to tetramethoxysilane (TMOS) was studied to improve the performance of a hybrid monolithic silica capillary column with 100-μm i.d. in HPLC in a range MTMS/TMOS (v/v) = 10/90–25/75. The domain size was also varied by adjusting the amount of PEG to control permeability (K = 2.8 × 10⁻¹⁴–6.9 × 10⁻¹⁴ m²). Evaluation of the performance for those capillary columns following octadecylsilylation proved an increase in retention factor (k) and a decrease in steric selectivity α(triphenylene/ortho-terphenyl) with the increase in MTMS content in the feed. The effect of the feed ratio was also observed in porosity and hydrophobic property of the C18 stationary phase from the results of size exclusion chromatography (SEC) and reversed phase characterization. The monolithic silica capillary columns prepared under new preparation conditions were able to produce a plate height of 4.6–6.0 μm for hexylbenzene in a mobile phase acetonitrile/water = 80/20 at a linear velocity of 2 mm/s. Consequently, it was possible to prepare hybrid monolithic silica capillary columns with higher performance than those reported previously while maintaining the retention factors in a similar range by reducing the MTMS/TMOS ratio and increasing the total silane concentration in feed.     

On-line stacking and sweeping capillary electrophoresis for detecting heroin metabolites in human urine

Heroin metabolites including morphine, codeine, and 6-acetylmorphine were determined by cation-selective exhaustive injection and sweeping micellar electrokinetic chromatography (CSEI–sweep-MEKC). Liquid–liquid extraction was used for urine pretreatment. An uncoated fused silica capillary (Ld = 30 cm, 50 μm ID) was filled with phosphate buffer (50 mM, pH 2.5) containing 30% methanol, then high conductivity buffer (100 mM phosphate, 41.3 kPa for 18 s) was followed. Samples were injected electrokinetically (20 kV, 300 s). The sweeping and separation were performed at −25 kV using phosphate buffer (20 mM, pH 2.5) and 80 mM sodium dodecyl sulfate. The baseline separation was done within 10 min. During method validation, the calibration curves were linear over a range of 50–500 ng/mL (r ≧ 0.994). The RSD and RE values in intra-day and inter-day assays were all below 20%, which showed good precision and accuracy. Their detection limits were 10 ng/mL (S/N = 3). The optimized method was applied to determine real urine samples from addicts. These samples were confirmed by liquid chromatography/mass spectrometry.     

Development of counter current salting-out homogenous liquid–liquid extraction for isolation and preconcentration of some pesticides from aqueous samples

In this paper, a new version of salting-out homogenous liquid–liquid extraction based on counter current mode combined with dispersive liquid–liquid microextraction has been developed for the extraction and preconcentration of some pesticides from aqueous samples and their determination by gas chromatography–flame ionization detection. In order to perform the method, aqueous solution of the analytes containing acetonitrile and 1,2-dibromoethane is transferred into a narrow bore tube which is filled partially with NaCl. During passing the solution through the tube, fine droplets of the organic phase are produced at the interface of solution and salt which go up through the tube and form a separated layer on the aqueous phase. The collected organic phase is removed and injected into de-ionized water for more enrichment of the analytes. Under the optimum extraction conditions, the method shows broad linear ranges for the target analytes. Enrichment factors and limits of detection for the selected pesticides are obtained in the ranges of 3480–3800 and 0.1–5 μg L⁻¹, respectively. Relative standard deviations are in the range of 2–7% (n = 6, C = 50 or 100 μg L⁻¹, each analyte). Finally, some aqueous samples were successfully analyzed using the developed method.     

Single solid phase extraction method for the simultaneous analysis of polar and non-polar pesticides in urine samples by gas chromatography and ultra high pressure liquid chromatography coupled to tandem mass spectrometry

A new multiresidue method has been developed and validated for the simultaneous extraction of more than two hundred pesticides, including non-polar and polar pesticides (carbamates, organochlorine, organophosphorous, pyrethroids, herbicides and insecticides) in urine at trace levels by gas and ultra high pressure liquid chromatography coupled to ion trap and triple quadrupole mass spectrometry, respectively (GC-IT-MS/MS, UHPLC-QqQ-MS/MS). Non-polar and polar pesticides were simultaneously extracted from urine samples by a simple and fast solid phase extraction (SPE) procedure using C₁₈ cartridges as sorbent, and dichloromethane as elution solvent. Recovery was in the range of 60-120%. Precision values expressed as relative standard deviation (RSD) were lower than 25%. Identification and confirmation of the compounds were performed by the use of retention time windows, comparison of spectra (GC-amenable compounds) or the estimation of the ion ratio (LC-amenable compounds). For GC-amenable pesticides, limits of detection (LODs) ranged from 0.001 to 0.436 μg L⁻¹ and limits of quantification (LOQs) from 0.003 to 1.452 μg L⁻¹. For LC-amenable pesticides, LODs ranged from 0.003 to 1.048 μg L⁻¹ and LOQs ranged from 0.011 to 3.494 μg L⁻¹. Finally, the optimized method was applied to the analysis of fourteen real samples of infants from agricultural population. Some pesticides such as methoxyfenozide, tebufenozide, piperonyl butoxide and propoxur were found at concentrations ranged from 1.61 to 24.4 μg L⁻¹, whereas methiocarb sulfoxide was detected at trace levels in two samples.     

Quantitative determination of triclocarban in wastewater effluent by stir bar sorptive extraction and liquid desorption–liquid chromatography–tandem mass spectrometry

Triclocarban is an antimicrobial and antibacterial agent found in personal care products and subsequently is a prevalent wastewater contaminant. A quantitative method was developed for the analysis of triclocarban in wastewater effluents using stir bar sorptive extraction–liquid desorption (SBSE–LD) followed by liquid chromatography–tandem mass spectrometry (LC–MS/MS) by means of an electrospray interface. A stir bar coated with polydimethylsiloxane (PDMS) is placed within a vial containing wastewater effluent and is stirred for an hour at room temperature. The PDMS stir bar is then placed in a LC vial containing methanol and is desorbed in a sonicator bath. The methanol is evaporated to dryness and reconstituted in 75% methanol. Spike and recovery experiments in groundwater that did not contain native concentrations of triclocarban were performed at 0.5 μg/L and were 93 ± 8%. Recoveries in wastewater effluent that were corrected for the background levels of triclocarban were 92 ± 2% and 96 ± 5%, respectively, when spiked with 0.5 and 5 μg/L of triclocarban. The precision of the method as indicated by the relative standard error was 2%. The limit of quantitation was 10 ng/L. The SBSE–LD–LC/MS/MS method was applied to wastewater effluent samples collected from northeast Ohio. Triclocarban was quantitated in all five effluent samples, and its concentration ranged from 50 to 330 ng/L. The described method demonstrates a simple, green, low-sample volume, yet, sensitive method to measure triclocarban in aqueous matrices.