Physical and mechanical properties of graphene oxide/polyethersulfone nanocomposites

The aim of this study was to investigate physical and mechanical properties of graphene oxide (GO)/polyethersulfone (PES) nanocomposite films. The films were produced by solution casting method. The mechanical properties of composite films were evaluated by tensile test. A significant enhancement in the mechanical properties of neat PES films was obtained incorporating a small amount of GO loading (0.05–1 wt.%). The highest tensile strength was observed at 1 wt.% of GO. Comparisons were made between experimental data and the Halpin–Tsai model predictions for the tensile strength and modulus of GO/PES composites. The effect of an orientation factor on model predictions was also acquired. The hydrophilicity of the nanocomposite was evaluated by assessing contact angle and enhanced wet ability of the films was obtained with increasing the amount of GO up to 1%. The morphology of the nanocomposites was investigated using scanning electron microscopy and transmission electron microscopy and the results revealed a good dispersion of GO in the PES matrix. The thermal behavior of the composite was also studied. Thermal stability of composites was increased by adding the GO. Copyright © 2013 John Wiley & Sons, Ltd.     

LDPE／EVA共混体系的结晶行为

本文通过DSC、WAXD、偏光显微镜、DMA等方法,对LDPE/EVA共混体系进行了研究。结果表明,EVA可使LDPE的熔融峰温提高15℃。并在LDPE结晶过程中起稀释剂作用。LDPE/EVA共混体系为非晶相相容。     

高密度聚乙烯／低密度聚乙烯／乙烯－醋酸乙烯共聚物共混体系的结晶行为

通过ＤＳＣ和ＷＡＸＤ研究了高密度聚乙烯／低密度聚乙烯／乙烯－醋酸乙烯共聚物（ＨＤＰＥ／ＬＤＰＥ／ＥＶＡ）三元共混体系的热行为和结晶性能。发现当ＨＤＰＥ含量小于４０％时，ＥＶＡ对ＬＤＰＥ起稀释剂作用，促进ＨＤＰＥ、ＬＤＰＥ的晶相分离，使ＨＤＰＥ、ＬＤＰＥ单独结晶．当ＨＤＰＥ含量高于４０％时，ＬＤＰＥ片晶进入ＨＤＰＥ晶相。形成与ＬＤＰＥ在片晶水平上的共晶。     

高密度聚乙烯／低密度聚乙烯／乙烯—醋酸乙烯共聚物共混体系的结晶行为

通过ＤＳＣ和ＷＡＸＤ研究了高密度聚乙烯／低密度聚乙烯／乙烯－醋酸乙烯共聚物（ＨＤＰＥ／ＬＤＰＥ／ＥＶＡ）三元共混体系的热行为和结晶性能，发现当ＨＤＰＥ含量小于４０％时，ＥＶＡ对ＬＤＰＥ起稀释剂作用，促进ＨＤＰＥ、ＬＤＰＥ的晶相分离，使ＨＤＰＥ、ＬＤＰＥ单独结晶，当ＨＤＰＥ含量高于４０％时，ＬＤＰＥ片晶入进ＨＤＰＥ晶相，形成与ＬＤＰＥ在片晶水平上的共晶。     

钨酸铋/还原氧化石墨烯二氧化氮传感器的研制EI北大核心CSCD

The bismuth tungstate / reduced graphene oxide (Bi2 WO6 / rGO) composite material was synthesized by a simple and one-step hydrothermal method, and the nitrogen dioxide gas sensor was prepared based on this material. The crystal phase, morphology and microstructure of composite were studied by XRD, Raman spectra, SEM and TEM,respectively, which confirmed that composite of Bi2 WO6 and rGO was successfully synthesized, and Bi2 WO6 / rGO composite material with flower-like superstructure was obtained. The composite material was loaded on the interdigital electrode to prepare the nitrogen dioxide gas sensor, while the properties of gas sensor were systemically investigated by using homemade gas-sensing test device. The results indicated that the Bi2 WO6 / rGO composite gas sensor had higher selectivity, higher response value and better long-term stability. The response value of Bi2 WO6 / rGO composite gas sensor was 28. 35% towards 47. 03 mg / m3 NO2, which was 3. 5 times of pure rGO gas sensor. The response time was 55 s with the recovery time of 549 s and the detection limit of 62 μg / m3. © 2022, Youke Publishing Co.,Ltd. All rights reserved.     

Effects of functionalized multiwalled carbon nanotubes on the morphologies and mechanical properties of PP/EVA blend

The maleic anhydride‐grafted multiwalled carbon nanotubes (MWCNTs‐g‐MA) have been introduced into polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) blend. To clearly describe the effects of MWCNTs‐g‐MA on the morphology and mechanical properties of PP/EVA blends, the selective distribution of MWCNTs‐g‐MA in the blends is realized through different sample preparation methods, namely, MWCNTs‐g‐MA disperse in EVA phase and MWCNTs‐g‐MA disperse in PP matrix. The results show that the distribution of MWCNTs‐g‐MA has an important effect on the final morphology of EVA and the crystallization structure of PP matrix. Compared with PP/EVA binary blend, distribution of MWCNTs‐g‐MA in PP matrix induces the aggregation of EVA phase at high EVA content and the decrease of spherulite diameters of PP matrix simultaneously. However, when MWCNTs‐g‐MA are dispersed in the EVA phase, they induce more homogeneous distribution of EVA, and the crystallization behavior of PP is slightly affected by MWCNTs‐g‐MA. The corresponding mechanical properties including impact strength and tensile strength are tested and analyzed in the work. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1481–1491, 2009     

Intercalation effects in LDPE/o-montmorillonites nanocomposites

Typical montmorillonite clays (Cloisite^® Na⁺, Cloisite^® 30B) were modified by treatment with octadecyl ammonium chloride (ODC) and successive additions of octadecylamine (ODA). XRD analyses of the modified clays indicated an increase of the basal spacing of the (0 0 1) planes depending on the ODC or ODA additions.Nanocomposites were prepared by dispersing the modified clays (3% w/w concentration) in LDPE, using a Brabender mixer. XRD measurements of the obtained products indicated in some cases the achievement of intercalation effects, which were confirmed by TEM analysis.Some thermal, mechanical, dynamic-mechanical and rheological properties were evaluated and correlated to the degree of intercalation.     

Thermal stability and flame retardancy of LDPE/EVA blends filled with synthetic hydromagnesite/aluminium hydroxide/montmorillonite and magnesium hydroxide/aluminium hydroxide/montmorillonite mixtures

The combination of organophillised montmorillonite (MMT), synthetic hydromagnesite and aluminium hydroxide (ATH) as flame retardant system for polyethylene-based materials was studied and compared with a similar system with magnesium hydroxide, ATH and MMT. The thermal stability and the flame retardant properties were evaluated by thermogravimetric analysis (TGA), differential thermal analysis (DTA), limiting oxygen index (LOI) and cone calorimeter tests. The results indicated that the addition of montmorillonite makes it possible to reduce the total filler content to achieve the flame retardant requirements. The thermal stability of filled LDPE/EVA blends increases to a higher extent for the samples containing MMT. In the cone calorimeter tests we observed a reduction of the peak heat release rate for the sample containing montmorillonite in comparison with a sample with higher filler loading without this nanoclay. An increase of the stability of the char formed could be responsible for this favourable behaviour when montmorillonite is added.In addition, mechanical properties significantly improved for the composites containing montmorillonite both for the filler loading reduction and the reinforcement effect of the nanoclay.     

Internal structure and linear viscoelastic properties of EVA/asphalt nanocomposites

The effect of the addition of two different organoclays as a third component in polymer-modified asphalts has been investigated. Ternary mixtures were prepared by adding clay and poly(ethylene-co-vinyl acetate) to the asphalt, either separately, or in the form of a premixed master batch. The performed characterizations allowed the determination of how the two methods of mixing influence the interactions between asphalt and polymer and therefore the final rheological properties. In particular, it was shown that the clay had a compatibilizing effect on asphalt and polymer and that a high compatibility between clay and polymer led to a better dispersion of the polymer in the asphalt, thus influencing the final rheological properties of the studied systems.     

Thermal stability and flammability properties of heterophasic PP-EP/EVA/organoclay nanocomposites

A study on the thermal behavior and flammability properties of the heterophasic polypropylene-(ethylene-propylene) copolymer (PP-EP)/poly(ethylene vinyl acetate) (EVA)/montmorillonite nanocomposite is presented. Nanoclay nanocomposites were prepared using a twin screw extruder. Both the fluidity of the EVA phase and compatibility conditions between PP-EP and EVA were used in order to obtain the required nanocomposites. Therefore, no additional compatibilizer was required to achieve the clay dispersion. Products exhibited the partially exfoliated/intercalated nanoclay dispersion. Thermogravimetric analyses indicated that nanoclays retard thermal degradation depending on nanoclay concentration. The retarding process was assigned to the exfoliation and dispersion of the silicate layers which impeded heat diffusion to the macromolecules. Thermal studies, under non-isothermal crystallization, indicated the lack of influence of nanoclay on the thermal behavior. Flammability characteristics were however affected by the nanoclay layers which overall generated flame retardation both in the EVA host and in the complex nanocomposites.     

A review on the mechanical,electrical and EMI shielding properties of carbon nanotubes and graphene reinforced polycarbonate nanocomposites

Recently, it has been found that carbon nanotubes (CNTs) and graphene could prove to be the most promising carbonaceous fillers in polymers nanocomposites field because of their better structural and functional properties. Their uniform dispersion in polymer matrix leads to significant improvements in their several properties. This paper reviews the effect of nanofillers, ie, CNTs, derivatized CNTs, and graphene on the polycarbonate nanocomposite and its application in aerospace, automobile, sports, electronic sectors, and various industries. The comparative analysis of carbon‐based fillers on the different properties of polycarbonate nanocomposites is also included.     

Studies on the mechanism for the sudden mechanical property drops of graphene/polymer nanocomposites

Graphene/polymer nanocomposites (GPNCs) have gained intense research interest in recent years. Graphene can improve the properties of the nanocomposites at low loadings, but usually causes sudden drops in the mechanical properties of the nanocomposites at similarly low loadings, risking the performance, reproducibility, and batch stability of the nanocomposites. This problem has been troubling the GPNCs field for years, but it is difficult to solve mainly because the mechanism of the sudden mechanical property drops has not been well documented yet. Here, we present a systematic study on this problem. At first, a statistical study was made to provide an overview of the sudden mechanical property drops. It was found that the sudden mechanical property drops were almost independent of the surface modification of graphene, and the in situ polymerization method sometimes leads to lower critical concentration than the solvent blending and melt blending methods. Then, we demonstrated a cutting‐off mechanism which unveiled that the formation of a continuous or semicontinuous network of graphene throughout the polymeric matrix was the main cause of the sudden mechanical property drops, and the low critical concentration of the sudden mechanical property drops was mainly due to the large aspect ratio of graphene. Finally, future research prospects were proposed. Overall, our work has provided new understandings and insights to the mechanical properties of GPNCs.     

硼掺杂还原态氧化石墨烯催化剂的制备及其蒽催化加氢性能的研究

制备了一系列硼掺杂的还原氧化态石墨烯催化剂并应用于蒽加氢反应。结果表明，随着催化剂处理温度的升高，催化剂中有序碳结构会发生变化，硼会取代材料骨架中的碳，进而影响蒽和氢气的吸附活化。经硼改性后，催化剂对蒽加氢反应表现出了很高的加氢活性，蒽的最高转化率可达97%，深度加氢产物八氢蒽的最高选择性可达19%。     

Towards high‐performance biopackaging: barrier and mechanical properties of dual‐action polycaprolactone/zinc oxide nanocomposites

The properties of nanocomposites of biodegradable polycaprolactone containing zinc oxide (ZnO) nanoparticles with diverse morphologies, that is, ZnO nanospheres, nanorods, and nanodisks are investigated. It is demonstrated for the first time that the dual action of the ZnO nanoparticles reduces the gas permeability of the nanocomposites via two mechanisms: first by the creation of a tortuous path and second by gas adsorption. Depending on the morphology of the particles, the oxygen permeability can be reduced by more than 60%. Tensile tests show that the nanocomposites remain very ductile. The nominal strain for all nanocomposites is higher than 500% before fracture occurs. The Young's modulus and tensile strength of the nanocomposites increase at higher ZnO concentrations. This behavior is more pronounced in the case of ZnO nanorods. As a result, the incorporation of ZnO nanoparticles into (bio)polymers provides an opportunity to manufacture polymer‐based nanocomposite materials, resulting in the production of high‐performance (bio)packaging. Copyright © 2011 John Wiley & Sons, Ltd.     

A facile approach to obtaining PVDF/graphene fibers and the effect of nanoadditive on the structure and properties of nanocomposites

The key factors in the design of nanocomposites include obtaining a good adhesion between components and homogeneous dispersion of the nanoadditive in the polymer matrix. Direct mixing of graphene with polymers which are then processed by melt compounding method results in strong tendency of nanoadditive to agglomerate. The article presents a new approach to obtaining poly(vinylidene fluoride)/graphene (PVDF/rGO) nanocomposites in the form of fibers. This method is characterized by the use of graphene oxide (GO) dispersed in the plasticizer instead of graphene. The combination of the fibers forming process with simultaneous reduction of GO to rGO allowed the authors to obtain nanocomposites with graphene homogeneously dispersed in the polymer matrix. Moreover, addition of graphene resulted in formation of β-phase in the nanocomposites, which is characteristic for PVDF and responsible for pyroelectric and piezoelectric properties of this polymer.     

Poly(lactic acid) nanocomposites with various organoclays. I. Thermomechanical properties,morphology, and gas permeability

The thermomechanical properties, morphology, and gas permeability of hybrids prepared with three types of organoclays were compared in detail. Hexadecylamine–montmorillonite (C₁₆–MMT), dodecyltrimethyl ammonium bromide–montmorillonite (DTA‐MMT), and Cloisite 25A were used as organoclays in the preparation of nanocomposites. From morphological studies using transmission electron microscopy, most clay layers were found to be dispersed homogeneously in the matrix polymer, although some clusters or agglomerated particles were also detected. The initial degradation temperature (at a 2% weight loss) of the poly(lactic acid) (PLA) hybrid films with C₁₆–MMT and Cloisite 25A decreased linearly with an increasing amount of organoclay. For hybrid films, the tensile properties initially increased but then decreased with the introduction of more of the inorganic phase. The O₂ permeability values for all the hybrids for clay loadings up to 10 wt % were less than half the corresponding values for pure PLA, regardless of the organoclay. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 94–103, 2003     

氧化石墨烯的制备及低温还原研究

用化学氧化法制备氧化石墨烯,并用一种新型的低温化学还原方法将其还原。用红外光谱、拉曼光谱、X射线衍射、X射线光电子能谱、扫描电镜、原子力显微镜等多种手段表征氧化石墨烯和还原氧化石墨烯的结构与形貌。结果表明,即使在低温条件下,壳聚糖依然可以还原氧化石墨烯,从而预示,在低温条件下,能够在同一环境下实现氧化石墨烯的还原和石墨烯的应用。     

Graphene oxide/epoxy composites with enhanced fracture toughness for liquid hydrogen storage

Graphene oxide (GO)/epoxy composites cured by aliphatic dibasic acids have been prepared. The influences of structure of aliphatic dibasic acid and loading of GO on curing process and mechanical properties of epoxy composites were studied. The results show that the reaction activities, gel time of corresponding epoxy-acid system and tensile strength of the formed epoxy resins decrease with the increase of the chain length of aliphatic dibasic acids. Both fracture toughness (>1.96 MPa⋅m^1/2) and elongations at break (>6%) increase with the increase of the chain length of aliphatic dibasic acids. The introduction of GO is helpful to increase the mechanical properties and the gas transmission coefficient of GO/epoxy composites. A maximum of tensile strength and elongations at break were obtained when the loading of GO is 0.6 wt%. The gas transmission coefficient of GO/epoxy composite increases with the increase of GO loading. The excellent mechanical properties and gas leakage resistance coefficient of the formed epoxy composites provides potential application in many fields where conventional brittle epoxy resins are inapplicable.     

Ionic liquid functionalized graphene oxide for enhancement of styrene‐butadiene rubber nanocomposites

Ionic liquid 1‐allyl‐3‐methyl‐imidazolium chloride (AMICl) is used to fine‐tune the surface properties of graphene oxide (GO) sheets for fabricating ionic liquid functionalized GO (GO‐IL)/styrene‐butadiene rubber (SBR) nanocomposites. The morphology and structure of GO‐IL are characterized using atomic force microscope, X‐ray diffraction, differential scanning calorimetry, X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, UV‐vis spectra and Raman spectra. The interaction between GO and AMICl molecules as well as the effects of GO‐IL on the mechanical properties, thermal conductivity and solvent resistance of SBR are thoroughly studied. It is found that AMICl molecules can interact with GO via the combination of hydrogen bond and cation–π interaction. GO‐IL can be well‐dispersed in the SBR matrix, as confirmed by X‐ray diffraction and scanning electron microscope. Therefore, the SBR nanocomposites incorporating GO‐IL exhibit greatly enhanced performance. The tensile strength, tear strength, thermal conductivity and solvent resistance of GO‐IL/SBR nanocomposite with 5 parts per hundred rubber GO‐IL are increased by 505, 362, 34 and 31%, respectively, compared with neat SBR. This method provides a new insight into the fabrication of multifunctional GO‐based rubber composites. Copyright © 2016 John Wiley & Sons, Ltd.     

GO/PVA nanocomposites with significantly enhanced mechanical properties through metalion coordination

In this study, a simple and efficient way is demonstrated to create strong interfacial interaction between graphene oxide(GO) filler and poly(vinyl alcohol)(PVA) matrix through metal ion coordination. The coordination bonding provides efficient load transfer during the tensile process, and enhances the mechanical properties of the nanocomposites significantly. After being coordinated with Cu(Ⅱ) ions, GO/PVA composites show much higher Young's moduli and yield stresses than pure PVA and noncoordinated GO/PVA. UV–vis and FTIR spectra are performed to confirm the successful coordination between GO and PVA. Ethylene diamine tetraacetic acid disodium salt(EDTA-2 Na) is used to confirm the important role of coordination in enhancing the composites. This research provides a new approach to manufacture polymer-matrix nanocomposites with significantly improved mechanical performances.