Electroanalysis of myoglobin and hemoglobin with a boron-doped diamond electrode

The electrochemical behavior of myoglobin (Mb) and hemoglobin (Hb) was investigated with a boron-doped diamond (BDD) electrode by cyclic voltammetry. In acetate buffer solutions, the oxygen reduction at the BDD electrode showed a very high overpotential while the reduction of Mb or Hb was observed in the more positive potential region. Owing to the electrocatalytic reaction of O₂ and the participation of H⁺ following the electrochemical reduction of ferric proteins, the voltammetric responses for Mb and Hb on the BDD electrode in the negative going scans became remarkable in acidic buffer solutions in air. The peak current was linearly proportional to the concentration of Mb in the range 1×10⁻⁶–2×10⁻⁵ M or the concentration of Hb from 1×10⁻⁶ to 1×10⁻⁵ M.     

Adsorption stripping voltammetry of phenol at Nafion-modified glassy carbon electrode in the presence of surfactants

In this paper, a new voltammetric method for the determination of phenol is described. In pH 8.00 phosphate buffer and in the presence of long-chain cationic surfactant—cetyltrimethylammonium bromide—phenol has a very sensitive oxidation peak at 0.47 V (vs. SCE) on the Nafion-modified glassy carbon electrode (GCE). The experimental parameters, such as supporting electrolyte and pH values, amounts of Nafion, varieties and concentration of surfactants, accumulation potential and time, as well as scan rate were optimized. The peak current is linear with the concentration of phenol in the range from 8×10⁻⁹ to 1×10⁻⁵ M, and the detection limit is 1×10⁻⁹ M after being accumulated at −0.50 V (vs. SCE) for 3 min. Trace levels of phenol in water samples were determined by using this voltammetric method, the average recovery was calculated to be 99.56%.     

Anodic voltammetric behaviors of methotrexate at a glassy carbon electrode and its determination in spiked human urine

The anodic voltammetric behavior of methotrexate was studied at glassy carbon electrode in acetate buffer (pH = 3.6) solution using cyclic, square-wave voltammetric and chronocoulometric techniques. The oxidation of methotrexate is an irreversible diffusion-controlled process. The oxidation mechanism was proposed and discussed in this work. The dependence of the current on pH, the concentration and nature of buffer, and instrumental parameters were investigated to optimize the experimental conditions for the determination of methotrexate. It was found that in the range of 8.0 × 10⁻⁷–2.0 × 10⁻⁵ mol/L, the currents measured by square-wave voltammetry presented a good linear property as a function of the concentrations of methotrexate. In addition, validation parameters, such as reproducibility, sensitivity and recovery were evaluated as well. The proposed method was also successfully applied for the determination of methotrexate in diluted human urine with good satisfactory.     

A novel poly(taurine) modified glassy carbon electrode for the simultaneous determination of epinephrine and dopamine

A novel taurine modified glassy carbon electrode was prepared by electropolymerization method. The electrochemical behaviors of epinephrine (EP) and dopamine (DA) at the modified electrode were studied by cyclic voltammetry. The modified electrode exhibited enhanced sensitivity and excellent electrochemical discrimination to DA and EP. The cathodic peaks of the two species were well-separated with a potential difference of about 390 mV, so the poly(taurine) modified electrode was used for simultaneous voltammetric measurement of EP and DA by differential pulse voltammetry. Under the optimum conditions, the cathodic peak currents were linear to concentrations of EP and DA in the range of 2.0 × 10⁻⁶ to 6.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁶ to 8.0 × 10⁻⁴ mol L⁻¹, respectively. The detection limits for EP and DA were 3.0 × 10⁻⁷ and 1.0 × 10⁻⁷ mol L⁻¹, respectively. Because the oxidation of ascorbic acid (AA) is an irreversible reaction at modified electrode, the interference of AA for determining EP and DA was eliminated. The modified electrode has been satisfactorily used for the simultaneous determination of EP and DA in pharmaceutical injections.     

Electrocatalytic Oxidation and Determination of Norepinephrine at Poly(Cresol Red) Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) was modified with electropolymerized films of cresol red in pH 5.6 phosphate buffer solution (PBS) by cyclic voltammetry (CV). The modified electrode shows an excellent electrocatalytic effect on the oxidation of norepinephrine (NE). The peak current increases linearly with the concentration of NE in the range of 3×10^?6–3×10^?5 M by the differential pulse voltammetry. The detection limit was 2×10^?7 M. The modified electrode can also separate the electrochemical responses of norepinephrine and ascorbic acid (AA). The separation between the anodic peak potentials of NE and AA was 190 mV by the cyclic voltammetry. And the responses to NE and AA at the modified electrode were relatively independent.     

Electrocatalytic response of dopamine at a dl-homocysteine self-assembled gold electrode

The gold electrode self-assembled with the homocysteine monolayer (Hcy/Au) is demonstrated to catalyze the electrochemical response of dopamine (DA) by cyclic voltammetry. A pair of well-defined redox waves was obtained and the calculated standard rate constant (k_s) is 2.1×10⁻² cm/s at the self-assembled electrode. The reduction peak of DA can be used to determine the concentration of DA in presence of ascorbic acid (AA) owing to the Hcy/Au also catalyzing the electrochemical oxidation of AA.     

Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

Improvement of alternariol monomethyl ether detection at gold electrodes modified with a dodecanethiol self-assembled monolayer

The electro-oxidation of alternariol monomethyl ether (AME), one of the main metabolites of the Alternaria genus mycotoxins, is studied at 1-dodecanethiol (DDT)-modified gold electrodes, in acetonitrile (ACN) – aqueous phosphate buffer solutions of different pH values, by using cyclic (CV) and square-wave (SWV) voltammetries. The AME voltammetric response at the bare electrode suffers from two drawbacks: it appears at potentials close to the onset of gold oxide formation, and it is hampered by a fouling of the electrode surface due to the accumulation of oxidized products. These shortcomings are circumvented by the use of DDT-coated electrodes, since the intervening monolayer inhibits gold oxide formation and surface passivation by the electrochemical products, without affecting the oxidation kinetics of AME significantly. Diagnostic criteria based on the voltammetric peak parameters show that the electrochemical behavior of AME at the modified electrode is mainly controlled by reactant diffusion from solution, with a weak adsorption of both the mycotoxin and its oxidation products at monolayer defects. Calibration curves were constructed from the AME square-wave voltammetric response and a detection limit of 9.1 × 10⁻⁸ mol dm⁻³ was determined, which is about three times smaller than a previous estimate at platinum and glassy carbon electrodes, and about fifty times smaller than the limit derived from measurements carried out at a polyphenol oxidase-modified carbon paste electrode.     

Electrochemical behavior of dopamine at a quercetin-SAM-modified gold electrode and analytical application

A stable quercetin–thioglycolic acid-modified gold electrode (Qu–TCA/Au) was prepared as a self-assembled monolayer (SAM) and its electrochemical behavior was investigated by electrochemical methods. In 0.05-M phosphate buffer solution (pH 7.0) quercetin exhibits quasi-reversible signals at the Qu–TCA/Au electrode. The stability of the quercetin-modified gold electrode is very good. The quercetin self-assembled monolayer is an effective mediator for the oxidation of dopamine, which was investigated by cyclic voltammetry and differential pulse voltammetry. Ascorbic acid does not interfere with determination of dopamine at an electrode modified with a mixture of quercetin–thioglycolic acid and quercetin–11-mercaptoundecanoic acid. This modification allows dopamine to be determined in the presence of ascorbic acid in the range from 3×10^–5 to 3×10^–4 M. The detection limit is 1×10^–6 M. Scanning electrochemical microscopy (SECM) was employed to study the electrochemical performances of the modified gold electrode indicating different feedback modes at differently modified surfaces.     

Poly(isonicotinic acid) modified glassy carbon electrode for electrochemical detection of norepinephrine

A glassy carbon electrode (GCE) was modified with electropolymerized films of isonicotinic acid in pH 5.6 phosphate buffer solution (PBS) by cyclic voltammetry (CV). The modified electrode showed an excellent electrocatalytical effect on the oxidation of norepinephrine (NE). In PBS of pH 7.4, the oxidation current increased linearly with two concentration intervals of NE, one is 4.0×10⁻⁷ to 1.0×10⁻⁵ M, the other is 1.0×10⁻⁵ to 2.0×10⁻⁴ M. The detection limit (S/N=3) obtained by DPV was 6.0×10⁻⁹ M. Then the modified electrode was used to determine NE in an excess of ascorbic acid (AA) by difference pulse voltammetry. The peak potentials recorded in a PBS of pH 7.4 were −68 and +111 mV versus SCE for AA and NE, respectively. The high selectivity and sensitivity for NE was found to be due to the very distinct attracting interaction between NE cations and the negtively charged poly(isonicotinic acid) film in pH 7.4 PBS. The proposed method exhibited good recovery and reproducibility.     

Simultaneous electrochemical determination of norepinephrine,ascorbic acid and uric acid using a graphene modified glassy carbon electrode

This paper describes the simultaneous determination of ascorbic acid (AA), norepinephrine (NE) and uric acid (UA) using a graphene modified glassy carbon electrode (GME) in pH 4.0 phosphate buffer solution. The electrochemical behaviors of AA, NE and UA at a bare glassy carbon electrode (GCE) and the GME were studied by cyclic voltammetry. Bare GCE failed to resolve the voltammetric signals of AA, NE and UA in a mixture, whereas the GME not only resolved their voltammetric signals, but also exhibited excellent electrocatalytic activity towards their electrochemical oxidation. The oxidation peak currents of AA, NE and UA were linearly proportional to their concentrations over the range of 1.0.0–1000.0, 0.6–45.0 and 1.0–100.0 μM, respectively, and their detection limits were 1.2, 0.10 and 0.60 μM, respectively, The modified electrode is of excellent sensitivity and selectivity, and has been satisfactorily used for the simultaneous determination of AA, NE and UA in their ternary mixture.     

Voltammetric Sensor for the Determination of Parathion Using an Electropolymerized Poly(Carmine) Film Electrode

A voltammetric sensor for the determination of parathion has been developed based on the use of a poly(carmine) film electrode. The reduction of parathion at the poly(carmine) modified glassy carbon electrode (GCE) is studied by cyclic voltammetry (CV) and linear scan voltammetry (LSV). Parathion yields a well-defined reduction peak at a potential of −0.595 V on the poly(carmine) modified GCE in pH 6.0 phosphate buffer solution (PBS). Compared with that on a bare GCE, the reduction peak current of parathion is significantly enhanced. All the experimental parameters are optimized for the determination of parathion. The reduction peak current is linear with the parathion concentration in the range of 5.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol L⁻¹, and the detection limit is 1.0 × 10⁻⁸ mol L⁻¹.     

Voltammetric study of the interaction of lomefloxacin (LMF)–Mg(II) complex with DNA and its analytical application

The voltammetric behavior of the LMF-Mg(II) complex with DNA at a mercury electrode is reported for the first time. In NH₃–NH₄Cl buffer (pH=9.10), the adsorption phenomena of the LMF–Mg(II) complex were observed by linear sweep voltammetry. The mechanism of the electrode reaction was found to be a reduction of LMF in the complex, and the composition of the LMF–Mg(II) complex is 2:1. In the presence of calf thymus DNA (ctDNA), the peak current of LMF–Mg(II) complex decreased considerably, and a new well-defined adsorptive reduction peak appeared at −1.63 V (vs. SCE). The electrochemical kinetic parameters and the binding number of LMF–Mg(II) with ctDNA were also obtained. Moreover, the new peak currents of LMF–Mg(II)–DNA system increased linearly correlated to the concentration of DNA in the 4.00×10⁻⁷–2.60×10⁻⁶ g ml⁻¹ range when the concentrations of LMF–Mg(II) complex was fixed at 5.00×10⁻⁶ mol l⁻¹, with the detection limits of 2.33×10⁻⁷ g ml⁻¹. An electrostatic interaction was suggested by electrochemical method.     

Simultaneous determination of hydroquinone and catechol at PASA/MWNTs composite film modified glassy carbon electrode

A poly-amidosulfonic acid and multi-wall carbon nanotubes composite (PASA/MWNTs) modified electrode has been constructed by electropolymerization on glassy carbon electrode (GCE). The electrochemical behaviors of hydroquinone (HQ) and catechol (CC) were investigated using cyclic and differential pulse voltammetries (DPVs) at the prepared electrode. Separation of the reductive peak potentials for HQ and CC was about 120 mV in pH 6.0 phosphate buffer solution (PBS), which makes it suitable for simultaneous determination of these compounds. In the presence of 1.0 × 10⁻⁴ mol L⁻¹ isomer, the reductive peak currents of DPV are proportional to the concentration of HQ in the range of 6.0 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹, and to that of CC in the range of 6.0 × 10⁻⁶ to 7.0 × 10⁻⁴ mol L⁻¹. When simultaneously changing the concentration of both HQ and CC, the linear concentration range of HQ (or CC) is 6.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ (or 6.0 × 10⁻⁶ to 1.8 × 10⁻⁴ mol L⁻¹), and the corresponding detection limits are 1.0 × 10⁻⁶ mol L⁻¹. The proposed method has been applied to simultaneous determination of HQ and catechol in water sample, and the results are satisfactory.     

Simultaneous determination of uric acid and ascorbic acid at a ferrocenium–thioglycollate modified electrode

Self-assembled monolayers (SAMS) of chemisorbed thioglycollate on a gold electrode surface have been used as a base interface for the electrostatic adsorption of ferrocenium ion. Electrochemical impedance spectra (EIS) and cyclic voltammetry (CV) were used to evaluate the electrochemical properties of the supramolecular film. The bare gold electrode failed to distinguish the oxidation peaks of ascorbic acid (AA) and uric acid (UA) in phosphate buffer solution (PBS, pH 7.0), while the ferricinium–thioglycollate modified electrode could separate them efficiently. In differiential pulse voltammetric measurements, the prepared gold electrode could separate AA and UA signals, allowing the simultaneous determination of AA and UA. Under optimal conditions and within the linear range of 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ M, the detection limits of AA and UA achieved were 2.0 × 10⁻⁷ and 1.0 × 10⁻⁷ M, respectively. The applicability of the prepared electrode was demonstrated by measuring AA and UA in human urine without any pretreatment. Figure Fabrication process for the modified electrode     

Determination of 4-methylbenzilidene camphor in sunscreen by square wave voltammetry in media of cationic surfactant

The voltammetric behavior of 4-methylbenzelidene camphor (MBC) was studied by square wave voltammetry (SWV) using mercury electrode. The experimental condition that provided the highest peak current with the best reduction signal definition of MBC was found in Britton-Robinson buffer and cationic surfactants, cetyltrimethylammoniun bromide (CTABr). A single peak of MBC reduction was observed at − 1.21 V versus Ag/AgCl. The developed methodology was applied for determination of MBC in commercial sunscreen SPF 15, 20 and 30 and for the simultaneous determination when other protection agents were associated, such as benzophenone-3 (BENZO) and octyl methoxycinammate (OMC). Both methodologies had shown good determination values for the analyzed samples. The calculated detection limit was 2.99 × 10^− 9 mol L^− 1 and the quantification limit was 9.98 × 10^− 9 mol L^− 1.     

Voltammetric Studies of Propylthiouracil at a Carbon-Paste Electrode Modified with Cobalt(II)-4-chlorosalophen: Application to Voltammetric Determination in Pharmaceutical and Clinical Preparations

A carbon-paste electrode chemically modified with a Schiff-base complex of cobalt (cobalt(II)-4-chlorosalophen, CoClSal) is utilized to investigate the voltammetric response of propylthiouracil (PTU). The mechanism of electrocatalytic oxidation of the compound is investigated by means of cyclic voltammetric studies applying various pHs to the buffered solutions. The modified electrode exhibits effective catalytic properties that lower the anodic overpotential and enhance the rate of electron transfer for the electrochemical oxidation of PTU. The results of the cyclic voltammetric (CV) and differential pulse voltammetric (DPV) techniques showed that the modified electrode exhibits good selectivity for discriminating between the anodic wave of PTU and some biological thiols (e.g. cysteine) which may be present in human serum samples. DPV is used as a very sensitive electroanalytical method for the detection of trace amounts of PTU in pharmaceutical and clinical preparations. The results showed that the anodic peak current for the analyte in DPV varies linearly with the concentration of PTU in the range of 7.5 × 10⁻⁶ to 7.5 × 10⁻⁴ M (RSD for the slope of calibration curve <4%, n = 6).     

An electropolymerized Nile Blue sensing film-based nitrite sensor and application in food analysis

This paper reports a poly-Nile Blue (PNB) sensing film based electrochemical sensor and the application in food analysis as a possible alternative for electrochemical detection of nitrite. The PNB-modified electrode in the sensor was prepared by in situ electropolymerization of Nile Blue at a prepolarized glassy carbon (GC) electrode and then characterized by cyclic voltammetry (CV) and pulse voltammetry in phosphate buffer (pH 7.1). Several key operational parameters affecting the electrochemical response of PNB sensing film were examined and optimized, such as polarization time, PNB film thickness and electrolyte pH values. As the electroactive PNB sensing film provides plenty of active sites for anodic oxidation of nitrite, the nitrite sensor exhibited high performance including high sensitivity, low detection limit, simple operation and good stability at the optimized conditions. The nitrite sensor revealed good linear behavior in the concentration range from 5.0 × 10⁻⁷ mol L⁻¹ to 1.0 × 10⁻⁴ mol L⁻¹ for the quantitative analysis of nitrite anion with a limit of detection of 1.0 × 10⁻⁷ mol L⁻¹. Finally, the application in food analysis using sausage as testing samples was investigated and the results were consistent with those obtained by standard spectrophotometric method.     

Electrochemistry and voltammetric determination of tannic acid on a single-wall carbon nanotube-coated glassy carbon electrode

The voltammetric behavior of tannic acid (TA) on a single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode has been investigated by cyclic voltammetry. TA can generate a well-defined anodic peak on the modified electrode at around 0.42 V (vs. SCE) in 0.10 M phosphate buffer solutions (pH = 4.0). The electrochemical reaction involves 1e transfer, accompanied by one proton. The electrode process is controlled by adsorption. The parameters affecting the response of TA, such as solution pH, accumulation time and accumulation potential are optimized for the determination of TA. Under the optimum conditions, the peak current changes linearly with the TA concentration in the range of 5.0 × 10⁻⁸–1.0 × 10⁻⁶ M. The lowest detectable concentration of TA is 8.0 × 10⁻⁹ M after 180 s accumulation. This method has been successfully applied to the determination of TA in tea and beer samples. In addition, the influence of potential interferents is examined. In the presence of bovine serum albumin, the peak current of TA decreases linearly due to the formation of a super-molecular complex.     

Electrochemical behavior of a covalently modified glassy carbon electrode with aspartic acid and its use for voltammetric differentiation of dopamine and ascorbic acid

Aspartic acid was covalently grafted on to a glassy carbon electrode (GCE) by amine cation radical formation in the electrooxidation of the amino-containing compound. X-ray photoelectron spectroscopic (XPS) measurement and cyclic voltammetric experiments proved the aspartic acid was immobilized as a monolayer on the GCE. Electron transfer to Fe(CN)₆^4– in solution of different pH was studied by cyclic voltammetry. Changes in solution pH resulted in the variation of the charge state of the terminal group; surface pK_a values were estimated on the basis of these results. Because of electrostatic interactions between the negatively charged groups on the electrode surface and dopamine (DA) and ascorbic acid (AA), the modified electrode was used for electrochemical differentiation between DA and AA. The peak current for DA at the modified electrode was greatly enhanced and that for AA was significantly reduced, which enabled determination of DA in the presence of AA. The differential pulse voltammetric (DPV) peak current was linearly dependent on DA concentration over the range 1.8×10^–6–4.6×10^–4 mol L^–1 with slope (nA mol^–1 L) and intercept (nA) of 47.6 and 49.2, respectively. The detection limit (3) was 1.2×10^–6 mol L^–1. The high selectivity and sensitivity for dopamine was attributed to charge discrimination and analyte accumulation. The modified electrode has been used for determination of DA in samples, in the presence of AA, with satisfactory results.