A vertical heat pipe: an experimental and statistical study of the thermal performance in the presence of low-frequency vibrations

New experimental results present the effects of low-frequency vibrations in a vertical heat pipe. The thermal resistance was investigated under different heat transfer rates, filling ratios and frequencies, increase of which improved the thermal performance. The vibrations were effective 33.83 % on the performance, and the best performance was estimated using the L16 array of Taguchi method, and it was achieved with the thermal resistance 0.064 K/W in the frequency 30 Hz.     

The experimental study on flat plate heat pipe of magnetic working fluid

An effective thermal spreader can achieve uniform heat flux distribution and thus enhance heat dissipation of heat sinks. Flat plate heat pipe is one of the highly effective thermal spreaders. Magnetic fluid is liquid and can be moved by the force of magnetic field. Therefore, the magnetic fluid is suitable to be used as the working fluid of flat plate heat pipes which have a very small gap between evaporation and condensation surfaces. We prepared a disk-shaped wickless flat plate heat pipe, and the distance between evaporation and condensation surfaces is only 1 mm. From experimental study, the effect of heat flux and working fluid ratio on the performance of flat plate heat pipe is presented. Also we compared the experimental results between the performance of water and magnetic fluid as working fluids.     

Effect of pore size distribution in bidisperse wick on heat transfer in a loop heat pipe

The purpose of this article is to experimentally investigate the effect of different pore size distributions in bidisperse wicks upon the heat transfer performance in a LHP. Three bidisperse wicks and one monoporous wick were tested in a loop heat pipe. The pore size distributions of the bidisperse wicks were measured, and the results reflected the three different large/small pore size ratios. The experiments showed that the maximum heat load of the monoporous wick reached about 400 W; and the three bidisperse wicks showed improvements on the maximum heat load up to 570 W. For the monoporous wick, the evaporator heat transfer coefficients of 10 kW/m² K and total thermal resistance of 0.19°C/W were achieved at a high heat load of 400 W. For the better bidisperse wick, the evaporator heat transfer coefficients could attain about 23 kW/m² K and total thermal resistance of 0.13°C/W. The results also indicated that a smaller cluster size in a bidisperse structure created a small pore size ratio. It was also found that the bidisperse wick with smaller clusters had a better enhancement in terms of the evaporator heat transfer coefficient.     

The influence of pipe length on thermal statistics computed from DNS of turbulent heat transfer

We present results from direct numerical simulation of turbulent heat transfer in pipe flow at a bulk flow Reynolds number of 5000 and Prandtl numbers ranging from 0.025 to 2.0 in order to examine the effect of streamwise pipe length (πδ ≡ πD/2 ? L ? 12πδ) on the convergence of thermal turbulence statistics. Various lower and higher order thermal statistics such as mean temperature, rms of fluctuating temperature, turbulent heat fluxes, two-point auto and cross-correlations, skewness and flatness were computed and it is found that the value of L required for convergence of the statistics depends on the Prandtl number: larger Prandtl numbers requires comparatively shorter pipe length for convergence of most of the thermal statistics.     

The influence of pipe length on thermal statistics computed from DNS of turbulent heat transfer

We present results from direct numerical simulation of turbulent heat transfer in pipe flow at a bulk flow Reynolds number of 5000 and Prandtl numbers ranging from 0.025 to 2.0 in order to examine the effect of streamwise pipe length (πδ ≡ πD/2 ⩽ L ⩽ 12πδ) on the convergence of thermal turbulence statistics. Various lower and higher order thermal statistics such as mean temperature, rms of fluctuating temperature, turbulent heat fluxes, two-point auto and cross-correlations, skewness and flatness were computed and it is found that the value of L required for convergence of the statistics depends on the Prandtl number: larger Prandtl numbers requires comparatively shorter pipe length for convergence of most of the thermal statistics.     

Investigation and analysis on a cellular heat pipe flat solar heater

A new cellular heat pipe flat solar energy collector is introduced, and the thermal performance of the new solar heater comprised by water heat pipe or acetone heat pipe is tested. The results are compared with the performance of the evacuated glass tube solar heater. It is found that: the heat loss coefficient of the cellular heat pipe flat solar heater is 54% less than that of the evacuated glass tube solar heater, while the daily average efficiency of solar absorbency is 15% higher, when the water temperature of heating is lower than 65°C. In conclusion, the thermal performance of such new solar heater is better than that of evacuated glass tube solar heater or ordinary flat solar heater, both of which are still popular in China. This new solar energy application promises to be a prosperous technology.     

A study of loop heat pipe with biporous wicks

The purpose of this study is to investigate the effects of various bimodal pore size distributions of biporous wicks for a loop heat pipe (LHP). The study was conducted following a statistical method using a two-level factorial plan involving three variables (particle size of pore former:74–88 and 125–149 μm Na₂CO₃, pore former content:20% by volume and 25% by volume, sintering temperature:700 and 750°C). Finally, the heat transport capability of the LHP between monoporous wicks and biporous wicks has been investigated. Experimental results show that, at the sink temperature of 10°C and the allowable evaporator temperature of 80°C, the heat transfer capacity of the better biporous wick achieved 200 W and the total thermal resistance was 0.31°C/W. The performance is enhanced about 60%, compared to a monoporous wick for 125 W and 0.53°C/W. Therefore, LHPs with biporous wicks are very attractive for high heat flux applications in the future.     

Experimental investigation of plastic finned-tube heat exchangers,with emphasis on material thermal conductivity

In this paper, two modified types of polypropylene (PP) with high thermal conductivity up to 2.3 W/m K and 16.5 W/m K are used to manufacture the finned-tube heat exchangers, which are prospected to be used in liquid desiccant air conditioning, heat recovery, water source heat pump, sea water desalination, etc. A third plastic heat exchanger is also manufactured with ordinary PP for validation and comparison. Experiments are carried out to determine the thermal performance of the plastic heat exchangers. It is found that the plastic finned-tube heat exchanger with thermal conductivity of 16.5 W/m K can achieve overall heat transfer coefficient of 34 W/m² K. The experimental results are compared with calculation and they agree well with each other. Finally, the effect of material thermal conductivity on heat exchanger thermal performance is studied in detail. The results show that there is a threshold value of material thermal conductivity. Below this value improving thermal conductivity can considerably improve the heat exchanger performance while over this value improving thermal conductivity contributes very little to performance enhancement. For the finned-tube heat exchanger designed in this paper, when the plastic thermal conductivity can reach over 15 W/m K, it can achieve more than 95% of the titanium heat exchanger performance and 84% of the aluminum or copper heat exchanger performance with the same dimension.     

Predict the temperature distribution in gas-to-gas heat pipe heat exchanger

A theoretical model has been developed to investigate the thermal performance of a continuous finned circular tubing of an air-to-air thermosyphon-based heat pipe heat exchanger. The model has been used to determine the heat transfer capacity, which expresses the thermal performance of heat pipe heat exchanger. The model predicts the temperature distribution in the flow direction for both evaporator and condenser sections and also the saturation temperature of the heat pipes. The approach used for the present study considers row-by-row heat-transfer in evaporator and condenser sections of the heat pipe heat exchanger.     

Experimental investigation on flow and heat transfer performance of a novel heat fin-plate radiator for electronic cooling

Within the electronics industry, high degree of integration and enhanced performance has led to high heat dissipation electronic devices. This has identified the future development of very high heat flux components. In this paper, a novel and high efficient diffusion welded heat fin-plate radiator (HFPR) was proposed and designed. Various parameters affect the thermal performance of HFPR. The effect of three parameters: the working fluid filling ratios (8% < FR < 70%), the vacuum degrees (0.001 Pa < VD < 0.1 Pa), and the air flow velocities (0.5 m/s < u < 6 m/s) were investigated experimentally. Using distilled water and ethanol as working fluids, a series of tests were carried out to find the influence of the above parameters on steady-state heat transfer characteristics of HFPR. The experimental results indicated that the filling ratio and vacuum degree had a significant influence on thermal performance of HFPR. Also compared with cooling performance using distilled water and ethanol, the HFPR cooling component using distilled water had a stronger heat dissipation capacity for the same filling ratio. The results also can provide a basis for optimal design of HFPR structure.     

Thermal performance of an open loop closed end pulsating heat pipe

This paper presents an experimental study of an open loop pulsating heat pipe (OLPHP) of 0.9 mm inner diameter. The performance characterization has been done using four working fluids at vertical and horizontal orientations. Water, Methanol, 2-Propanol and Acetone has been employed as the working fluid with 50% fill ratio. The experimental results indicate a strong influence of gravity and thermo physical properties of the working fluids on the performance of OLPHP. Considering all the working fluids used, Water has shown better thermal performance in vertical orientation while Methanol has shown better performance in horizontal orientation. All the working fluids perform better at horizontal orientation.     

Application of nanofluids to a heat pipe liquid-block and the thermoelectric cooling of electronic equipment

Microprocessor power dissipation is constantly increasing. An increase in microprocessor size has also resulted in higher heat fluxes. The growth of information technology has rapidly increased over the past few years, causing an increase in the demand for a microprocessor that has a very high computing ability. The previous generation of central processing units (CPU) had 1.17 billion transistors planted in it, which indicates that a significant amount of heat was generated. The total heat dissipation resulting from a high end CPU is approximately 110-140 W, which will increase if the CPU voltage and frequency increase. Conventional air-cooled cooling systems are no longer adequate to remove these heat fluxes. For a number of applications, direct air-cooling systems will have to be replaced or enhanced by other high performance compact cooling techniques. In this study, the application of nanofluids as the working fluid on a heat pipe liquid-block combined with thermoelectric cooling is investigated. The type and effect of volume concentrations of nanofluids, coolant temperature, and thermoelectricsystem as heat pumps of a PC on the CPU’s temperature are considered. The results obtained from this technique are compared to those from other conventional cooling techniques. The heat pipe liquid-block combined with the thermoelectric system has a significant effect on heat transfer from the CPU. The higher thermal performance heat pipe liquid-block and thermoelectric cooled system with nanofluids proved its potential as a working fluid.     

Theoretical investigation on thermal performance of heat pipe flat plate solar collector with cross flow heat exchanger

Based on the heat transfer characteristics of absorber plate and the heat transfer effectiveness-number of heat transfer unit method of heat exchanger, a new theoretical method of analyzing the thermal performance of heat pipe flat plate solar collector with cross flow heat exchanger has been put forward and validated by comparisons with the experimental and numerical results in pre-existing literature. The proposed theoretical method can be used to analyze and discuss the influence of relevant parameters on the thermal performance of heat pipe flat plate solar collector.     

Experimental investigation of the coherent structures in a spirally corrugated pipe

Previous numerical and theoretical results (Chen et al., 2019; Liu et al., 2018; Zhao et al., 2019) based on the optimization theory of convective heat transfer reveal that the optimized flow structures in a straight circular pipe enhancing convective heat transfer are multiple longitudinal vortices. This conclusion encourages us to find out whether such flow structures really exist in some enhanced heat transfer pipes by means of advanced experimental techniques. Therefore, a typical enhanced heat transfer pipe was selected, namely a spirally corrugated pipe, and stereoscopic particle image velocimetry (SPIV) was employed to measure its internal instantaneous flow field. Moreover, the proper orthogonal decomposition (POD) method was used to extract the large-scale coherent structures from the measured instantaneous velocity fields. Besides the spirally corrugated pipe, the fully developed turbulent flow in a straight pipe was also analyzed as benchmark of the enhanced heat transfer pipes. The results reveal that longitudinal whirling flow with multi-vortices is formed in both the fully developed turbulent flow field of the straight pipe and the spirally corrugated one. It is thus easy to explain the heat transfer enhancement mechanism of the above flow structures from the perspective of momentum transfer. The flow structures of the fully developed turbulent flow in a straight pipe are quite similar to the optimal flow pattern from the optimization theory. More specifically, multiple longitudinal vortices are spontaneously generated due to turbulence without external heat transfer enhancement techniques. Furthermore, the flow structures similar to multiple longitudinal vortices also exist in the spirally corrugated pipe, although these flow structures deviate from symmetric multiple vortices. Moreover, the flow structures in the spirally corrugated pipe are much more energetic than those in the fully developed turbulent flow in a straight pipe. This is probably the reason why a spirally corrugated pipe can enhance heat transfer compared with a straight circular pipe.     

Thermal performance of a carbon fiber composite material heat sink in an FC-72 thermosyphon

This study analyzes the use of a carbon fiber epoxy heat sink for evaporator surface enhancement in a FC-72 thermosyphon. The pin-fin heat sink features 945 small-cross-section (1.27 mm by 0.965 mm) fins fabricated with an integral base plate. These fins have a high thermal conductivity (500 W/m K) along the length of the fin. The influence of heat load, thermosyphon fill volume, and condenser operating temperature on the overall thermal performance is examined. The results of this experiment provide significant insight into the possible implementation and potential benefits of carbon-fiber heat sink technology in two-phase flow leading to significant improvements in thermal management strategies for advanced electronics.     

Experimental investigation on the photovoltaic–thermal solar heat pump air-conditioning system on water-heating mode

An experimental study on operation performance of photovoltaic–thermal solar heat pump air-conditioning system was conducted in this paper. The experimental system of photovoltaic–thermal solar heat pump air-conditioning system was set up. The performance parameters such as the evaporation pressure, the condensation pressure and the coefficient of performance (COP) of heat pump air-conditioning system, the water temperature and receiving heat capacity in water heater, the photovoltaic (PV) module temperature and the photovoltaic efficiency were investigated. The experimental results show that the mean photovoltaic efficiency of photovoltaic–thermal (PV/T) solar heat pump air-conditioning system reaches 10.4%, and can improve 23.8% in comparison with that of the conventional photovoltaic module, the mean COP of heat pump air-conditioning system may attain 2.88 and the water temperature in water heater can increase to 42 °C. These results indicate that the photovoltaic–thermal solar heat pump air-conditioning system has better performances and can stably work.     

Delay in response of turbulent heat transfer against acceleration or deceleration of flow in a pipe

To predict the heat transfer enhancements that result from the application of a pulsating flow in a pipe, we experimentally investigated the turbulent heat transfer variations produced in response to sudden accelerations or decelerations to flows within a pipe. To accomplish this, the Reynolds numbers with the valve open (Re₁) and close (Re₀) were systematically varied in the range of 8,000 ≤ Re₁ ≤ 34,000 and 700 ≤ Re₀ ≤ 23,000, respectively, and in-pipe spatiotemporal heat transfer variations were measured using infrared thermography simultaneously with temporal variations to the in-pipe flow properties. Based on the experimental results, it was found that the heat transfer delays that occur in response to accelerations or decelerations can be characterized using the corresponding time lag Δt and first-order time constant τ. The values of Δt and τ can be expressed as non-dimensional forms of Δt/(ν/u_τ²) and τ/(R/u_τ), respectively, where u_τ is the pipe wall friction velocity, ν is the kinematic viscosity of the fluid, and R is the pipe radius.     

Performance analysis of wick-assisted heat pipe solar collector and comparison with experimental results

The performance of heat pipe solar collector is investigated theoretically and experimentally. The system employs wick-assisted heat pipe for the heat transfer from the absorber (evaporator) to a heat exchanger (condenser). The heat pipe is made with a copper tube and the evaporator section is finned with aluminium plate. Theoretical model predicts the outlet water from heat exchanger, heat pipe temperature and also the thermal efficiency of solar collector. The results are compared with experimental data.     

Theoretical analysis to investigate thermal performance of co-axial heat pipe solar collector

The thermal performance of co-axial heat pipe solar collector which consist of a collector 15 co-axial heat pipes surrounded by a transparent envelope and which heat a fluid flowing through the condenser tubes have been predicted using heat transfer analytical methods. The analysis considers conductive and convective losses and energy transferred to a fluid flowing through the collector condenser tubes. The thermal performances of co-axial heat pipe solar collector is developed and are used to determine the collector efficiency, which is defined as the ratio of heat taken from the water flowing in the condenser tube and the solar radiation striking the collector absorber. The theoretical water outlet temperature and efficiency are compared with experimental results and it shows good agreement between them. The main advantage of this collector is that inclination of collector does not have influence on performance of co-axial heat pipe solar collector therefore it can be positioned at any angle from horizontal to vertical. In high building where the roof area is not enough the co-axial heat pipe solar collectors can be installed on the roof as well as wall of the building. The other advantage is each heat pipe can be topologically disconnected from the manifold.     

Average Nusselt number correlation in the thermal entrance region of steady and pulsating turbulent pipe flows

Empirical correlation has been developed for local and average Nusselt numbers in the thermal entrance region of steady and pulsating turbulent air-flows in a pipe. The correlation was based on experimental data obtained from experiment carried out on a pipe heated under uniform heat flux conditions. The rate of flow was periodically varied at frequencies ranging from 1 Hz to 13 Hz while the average Reynolds number varied from 6400 to 42000. Received on 20 October 1998