Mechanism and kinetics of crystallization of α-Fe in amorphous Fe81B13Si4C2 alloy

The non-isothermal crystallization of α-Fe from Fe₈₁B₁₃Si₄C₂ amorphous alloy was investigated. The kinetic parameters of crystallization process were determined by Kissinger and Kissinger–Akahira–Sunose (KAS) methods. It was established that the kinetic parameters of transformation do not change with the degree of crystallization in the range of 0.1–0.7. The kinetic model of the crystallization process was determined using the Malek's procedure. It was established that the primary crystallization α-Fe phase from amorphous alloy can be described by Šesták–Berggren autocatalytic model with kinetic triplet E_a = 349.4.0 kJ mol⁻¹, ln A = 50.76 and f(α) = α^0.72(1 − α)^1.02.     

The oxidation mechanisms of Cu54Ni45Mn1 (Constantan) tapes: Kinetic analysis

The kinetic parameters, namely the triplet activation energy E_A, model function f(α) or g(α) and pre-exponential factor A of the oxidation of Constantan tapes in 1 atm of oxygen have been determined from both isothermal and non-isothermal thermogravimetry. For isothermal experiments, with temperatures ranging from 650 °C to 900 °C, the results from direct conversion of the weight increase as a function of the time and curve fitting, are compared with the isoconversion method. For the non-isothermal experiments, with heating rates from 1 °C/min to 20 °C/min, comparison is made between the Friedman differential method and the integral methods of Kissinger, Ozawa and Li and Tang. All methods give apparent activation energies with relative standard deviations as low as 3%. The results converge to the identification of three stages in the oxidation behaviour. A parabolic law for reaction extents α below 15% with E_A = 246 ± 7 kJ mol⁻¹, ln A = 14.3, is followed by two linear stages with E_A = 244 ± 4 kJ mol⁻¹ and ln A = 15.3 for 0.18 < α < 0.35 and E_A = 228 ± 15 kJ mol⁻¹, ln A ≈ 13 for α > 45%, respectively.     

Recombination of HCO and DCO ions with electrons

Recombination of HCO⁺ and DCO⁺ ions with electrons was studied in afterglow plasma. The flowing afterglow with Langmuir probe (FALP) apparatus was used to measure the recombination rate coefficients and their temperature dependencies in the range 150–270 K. To obtain a recombination rate coefficient for a particular ion, the dependencies on partial pressures of gases used in the ion formation were measured. The variations of α_HCO⁺(T) and α_DCO⁺(T) seem to obey the power law: α_HCO⁺(T) = (2.0 ± 0.6) × 10⁻⁷ (T/300)^−1.3 cm³ s⁻¹ and α_DCO⁺(T) = (1.7 ± 0.5) × 10⁻⁷ (T/300)^−1.1 cm³ s⁻¹ over the studied temperature range.     

Kinetic model of poly(3-hydroxybutyrate) thermal degradation from experimental non-isothermal data

The non-isothermal data given by TG curves for poly(3-hydroxybutyrate) (PHB) were studied in order to obtain a consistent kinetic model that better represents the PHB thermal decomposition. Thus, data obtained from the dynamic TG curves were suitably managed in order to obtain the Arrhenius kinetic parameter E according to the isoconversional F-W-O method. Once the E parameters is found, a suitable logA and kinetic model (f(α)) could be calculated. Hence, the kinetic triplet (E±SD, logA±SD and f(α)) obtained for the thermal decomposition of PHB under non-isothermal conditions was E=152±4 kJ mol⁻¹, logA=14.1±0.2 s⁻¹ for the kinetic model, and the autocatalytic model function was: f(α)=α^m(1−α)ⁿ=α^0.42(1−α)^0.56.     

Comparative evolved gas analytical and structural study on trans-diammine-bis(nitrito)-palladium(II) and platinum(II) by TG/DTA–MS, TG–FTIR, and single crystal X-ray diffraction

Detailed study on identification and thermal decomposition of solid title compounds 1 and 2 crystallized from the used aqueous ammonia solutions of Pd(NH₃)₂(NO₂)₂ and Pt(NH₃)₂(NO₂)₂, has been carried out. Beyond the composition of complexes 1 and 2, their trans square planar configuration have already been recognized by reference IR spectra and powder XRD patterns, nevertheless their exact molecular and crystal structure as of trans-Pd(NH₃)₂(NO₂)₂ (1, Pd-NN) and trans-Pt(NH₃)₂(NO₂)₂ (2, Pt-NN) has been determined by single crystal X-ray diffraction (R = 0.0515 and 0.0341), respectively. Despite their compositional and configuration analogy, they crystallize in different crystal systems and space groups. The crystals of 1 (Pd-NN) are triclinic (space group No. 2, P-1, a = 5.003(1) Å, b = 5.419(1) Å, c = 6.317(1) Å, α = 91.34(2)°, β = 111.890(10)°, γ = 100.380(10)°), while those of 2 (Pt-NN) are monoclinic (space group No. 5, C2, a = 7.4235(16) Å, b = 9.130(2) Å, c = 4.4847(10) Å, β = 99.405(7)°).The pyrolytic processes of 1 and 2 (which might be sensitive to shock and heat) have been followed by simultaneous thermogravimetric and differential thermal analysis (TG/DTA), while the evolved gaseous species have been traced in situ by online coupled TG/DTA–EGA–MS and TG–EGA–FTIR instruments in He and air. Pd and Pt powders, forming as final solid products in single step, are captured and checked by TG and XRD. Whilst the unified evolved gas analyses report evolution of N₂, H₂O, NH₃, N₂O, NO, and NO₂ gases as gaseous product components in the exothermic decomposition of both trans-Pd(NH₃)₂(NO₂)₂ (1) and trans-Pt(NH₃)₂(NO₂)₂ (2) starting from ca. 230 and 220 °C, in sealed crucibles with a pinhole on the top, respectively.     

A novel 18-metallacrown-6 complex: Synthesis, structural characterization and magnetic properties

The novel 18-metallacrown-6 complex, with the formula of [Mn₆(C₁₁H₁₁N₂O₃)₆(CH₃CH₂OH)₆]·3C₃H₇NO·2CH₃CH₂OH (1) (pmshz = N-propanoyl-3-methyl-salicylhydrazide), has been prepared and characterized. The self-assembled, manganese complex assumes a nearly planar cyclic structure with an [Mn–N–N]₆ backbone. Due to the coordination, the ligand enforces the stereochemistry of the Mn³⁺ ions as a propeller shape with alternating …ΔΛΔΛ… configurations. The magnetic properties of the metallacrown molecule are characterized by a weak antiferromagnetic exchange interaction between the Mn³⁺ ion spins with S = 2 in the cyclic system.     

Molybdenum(VI) network polymers based on anion–π interaction and hydrogen bonding: Synthesis, crystal structures and oxidation catalytic application

A crystallographic investigation of anion–π interactions and hydrogen bonds on the preferred structural motifs of molybdenum(VI) complexes has been carried out. Two molybdenum(VI) network polymers MoO₂F₄·(Hinca)₂ (1) and MoO₂F₃(H₂O)·(Hinpa) (2), where inca = isonicotinamide and inpa = isonipecotamide, have been synthesized, crystallographically characterized and successfully applied to alcohol oxidation reaction. Complex 1 crystallizes in the monoclinic space C2/c: a = 16.832(3) Å, b = 8.8189(15) Å, c = 12.568(2) Å, β = 118.929(3)°, V = 1560.1(5) Å³, Z = 4. Complex 2 crystallizes in the triclinic space P-1: a = 5.459(2) Å, b = 9.189(4) Å, c = 12.204(5) Å, α = 71.341(6)°, β = 81.712(7)°, γ = 77.705(7)°, V = 564.8(4) Å³, Z = 2. Complex 1 consists of hydrogen bonding and anion–π interactions, both of which are considered as important factors for controlling the geometric features and packing characteristics of the crystal structure. The geometry of the sandwich complex of [MoO₂F₄]²⁻ with two pyridine rings indicates that the anion–π interaction is an additive and provides a base for the design and synthesis of new complexes. For complex 2, the anions and the protonated inpa ligands form a 2D supramolecular network by four different types of hydrogen contacts (N–HF, N–HO, O–HF and O–HO). The catalytic ability of complexes 1 and 2 has also been evaluated by applying them to the oxidation of benzyl alcohol with TBHP as oxidant.     

Kinetics of Direct Reduction of Chrome Iron Ore

The kinetics of direct reduction of artificial chrome iron ore was studied by isothermal and non-isothermal methods. In the initial, middle and final periods, the reaction is controlled by nucleation and growth, a phase boundary reaction, and diffusion, respectively. In the main reaction region, the kinetic equation is 1–(1–)^1/3=kt and the apparent activation energy is 270 kJ mol^–1. The kinetic mechanisms found with the isothermal and non-isothermal methods do not differ, and the activation energy values are approximately the same. However, the non-isothermal method can demonstrate the kinetic process completely.This revised version was published online in November 2005 with corrections to the Cover Date.     

Vapor pressure, kinetics and enthalpy of sublimation of bis(2,2,6,6-tetramethyl-3,5-heptanedionato)copper(II)

The kinetics of sublimation of bis(2,2,6,6-tetramethyl-3,5-heptanedionato)copper(II), [Cu(tmhd)₂] was studied by non-isothermal and isothermal thermogravimetric (TG) methods. The non-isothermal sublimation activation energy values determined following the procedures of Friedman, Kissinger, and Flynn–Wall methods yielded 93 ± 5, 67 ± 2, and 73 ± 4 kJ mol⁻¹, respectively and the isothermal sublimation activation energy was found to be 97 ± 3 kJ mol⁻¹ over the temperature range of 375–435 K. The dynamic TG run proved the complex to be completely volatile and the equilibrium vapor pressure (p_e)_T of the complex over the temperature range of 375–435 K determined by a TG-based transpiration technique, yielded a value of 96 ± 2 kJ mol⁻¹ for its standard enthalpy of sublimation (Δ_subH°).     

Effect of chelating agent on the oxidation rate of PCP in the magnetite/H2O2 system at neutral pH

The complex [Rh(CO)₂Cl]₂ reacts with two molar equivalent of pyridine carboxylic acids ligands Py-2-COOH(a), Py-3-COOH(b) and Py-4-COOH(c) to yield rhodium(I) dicarbonyl chelate complex [Rh(CO)₂(L^/)](1a) {L^/ = η²-(N,O) coordinated Py-2-COO⁻(a^/)} and non-chelate complexes [Rh(CO)₂ClL^//](1b,c) {L^// = η¹-(N) coordinated Py-3-COOH(b), Py-4-COOH(c)}. The complexes 1 undergo oxidative addition (OA) reactions with different electrophiles such as CH₃I, C₂H₅I, C₆H₅CH₂Cl and I₂ to give penta coordinated Rh(III) complexes of the types [Rh(CO)(CORⁿ)XL^/], {n = 1,2,3; R¹ = CH₃(2a); R² = C₂H₅(3a); X = I and R³ = CH₂C₆H₅ (4a); X = Cl}, [Rh(CO)I₂L^/](5a), [Rh(CO)(CORⁿ)ClXL^//] {R¹ = CH₃(6b,c); R² = C₂H₅(7b,c); X = I and R³ = CH₂C₆H₅ (8b,c); X = Cl} and [Rh(CO)ClI₂L^//](9b,c). The complexes have been characterized by elemental analysis, IR and ¹H NMR spectroscopy. Kinetic data for the reaction of 1a–b with CH₃I indicate a first order reaction. The catalytic activity of 1a–c for the carbonylation of methanol to acetic acid and its ester is evaluated and a higher turn over number (TON = 810–1094) is obtained compared with that of the well-known commercial species [Rh(CO)₂I₂]⁻ (TON = 653) at mild reaction conditions (temperature 130 ± 5 °C, pressure 35 ± 5 bar).     

Structural studies of cyclic ureas: 2. Enthalpy of formation of parabanic acid

Thermophysical and thermochemical studies have been carried out for crystalline parabanic acid. The thermophysical study was made by differential scanning calorimetry, DSC, over the temperature interval between T = (263 and 473) K. Two phase transitions were found: at T = (392.3 ± 1.6) K with the enthalpy of transition of (2.1 ± 0.4) kJ · mol⁻¹ and at T = (509.8 ± 1.5) K, when the compound was scanned to its fusion temperature. The standard (p = 0.1 MPa) molar enthalpy of formation, at T = 298.15 K, for crystalline parabanic acid was determined using static-bomb combustion calorimetry as −(590.2 ± 1.0) kJ · mol⁻¹. The standard molar enthalpy of sublimation, at T = 298.15 K, was derived from the variation of their vapour pressures, measured by the Knudsen-effusion method, with the temperature. These two thermochemical parameters yielded the standard molar enthalpy of formation in the gaseous phase, at T = 298.15 K, as −(470.8 ± 1.2) kJ · mol⁻¹.     

A computational study and fragment analysis of the back-bonding in Titanocenyl Complexes containing a five-member L,L′-cyclic ligand, L,L′ = O,O′; S,S′ or Se,Se′

A DFT computational study is performed on different Cp₂Ti^IV(L,L′-BID) complexes with L,L′-BID = dioxolene, dithiolene or diselenolene. A fragment analysis of the titanocene-ligand bonding in the DFT optimized geometries showed that out of plane folding for maximum Ti ← L π donation increases Cp₂Ti^IV(O,O′-BID) (35°) < Cp₂Ti^IV(S,S′-BID) (43–49°) < Cp₂Ti^IV(Se,Se′-BID) (48–53°).     

Standard molar enthalpies of formation of 2-, 3- and 4-cyanobenzoic acids

The standard (p = 0.1 MPa) molar enthalpies of formation of 2-, 3- and 4-cyanobenzoic acids were derived from their standard molar energies of combustion, in oxygen, at T = 298.15 K, measured by static bomb combustion calorimetry. The Calvet high temperature vacuum sublimation technique was used to measure the enthalpies of sublimation of 2- and 3-cyanobenzoic acids. The standard molar enthalpies of formation of the three compounds, in the gaseous phase, at T = 298.15 K, have been derived from the corresponding standard molar enthalpies of formation in the condensed phase and standard molar enthalpies for phase transition. The results obtained are −(150.7 ± 2.0) kJ · mol⁻¹, −(153.6 ± 1.7) kJ · mol⁻¹ and −(157.1 ± 1.4) kJ · mol⁻¹ for 2-cyano, 3-cyano and 4-cyanobenzoic acids, respectively. Standard molar enthalpies of formation were also estimated by employing two different methodologies: one based on the Cox scheme and the other one based on several different computational approaches. The calculated values show a good agreement with the experimental values obtained in this work.     

Nitric oxide and singlet oxygen photo-generation by light irradiation in the phototherapeutic window of a nitrosyl ruthenium conjugated with a phthalocyanine rare earth complex

The photochemical, photophysical and photobiological studies of a mixture containing cis-[Ru(H-dcbpy⁻)₂(Cl)(NO)] (H₂-dcbpy = 4,4′-dicarboxy-2,2′-bipyridine) and Na₄[Tb(TsPc)(acac)] (TsPc = tetrasulfonated phthalocyanines; acac = acetylacetone), a system capable of improving photodynamic therapy (PDT), were accomplished. cis-[Ru(H-dcbpy⁻)₂(Cl)(NO)] was obtained from cis-[Ru(H₂-dcbpy)₂Cl₂]·2H₂O, whereas Na₄[Tb(TsPc)(acac)] was obtained by reacting phthalocyanine with terbium acetylacetonate. The UV–Vis spectrum of cis-[Ru(H-dcbpy⁻)₂(Cl)(NO)] displays a band in the region of 305 nm (λ_max in 0.1 mol L⁻¹ HCl)(π–π*) and a shoulder at 323 nm (MLCT), while the UV–Vis spectrum of Na₄[Tb(TsPc)(acac)] presents the typical phthalocyanine bands at 342 nm (Soret λ_max in H₂O) and 642, 682 (Q bands). The cis-[Ru(H-dcbpy⁻)₂(Cl)(NO)] FTIR spectrum displays a band at 1932 cm⁻¹ (Ru–NO⁺). The cyclic voltammogram of the cis-[Ru(H-dcbpy⁻)₂(Cl)(NO)] complex in aqueous solution presented peaks at E = 0.10 V (NO^+/0) and E = −0.50 V (NO^0/−) versus Ag/AgCl. The NO concentration and ¹O₂ quantum yield for light irradiation in the λ > 550 nm region were measured as [NO] = 1.21 ± 0.14 μmol L⁻¹ and ø_OS = 0.41, respectively. The amount of released NO seems to be dependent on oxygen concentration, once the NO concentration measured in aerated condition was 1.51 ± 0.11 μmol L⁻¹ The photochemical pathway of the cis-[Ru(H-dcbpy⁻)₂(Cl)(NO)]/Na₄[Tb(TsPc)(acac)] mixture could be attributed to a photoinduced electron transfer process. The cytotoxic assays of cis-[Ru(H-dcbpy^-)₂(Cl)(NO)] and of the mixture carried out with B16F10 cells show a decrease in cell viability to 80% in the dark and to 20% under light irradiation. Our results document that the simultaneous production of NO and ¹O₂ could improve PDT and be useful in cancer treatment.     

Coordination chemistry of di-2-pyridylketone. Synthesis, spectroscopic investigations, X-ray studies and DFT calculations of Re(III) and Re(V) complexes

The paper presents a combined experimental and computational study of Re(III) and Re(V) complexes containing di-2-pyridylketone and its gem-diol form – [ReCl₃(dpk-N,O)(PPh₃)] (1), [ReCl₃(dpk-N,N′)(OPPh₃)] (2) and [ReOBr₃(dpk-OH)]·2(dpkH⁺Br⁻) (3). All the complexes have been characterized spectroscopically and structurally (by single-crystal X-ray diffraction). The complex 2 has been additionally studied by magnetic measurement. The magnetic behavior of 2 is characteristic of mononuclear octahedral Re(III) complex with d⁴ low-spin (³T_1g ground state) and arise because of the large spin–orbit coupling (ζ = 2500 cm⁻¹), which gives diamagnetic ground state. DFT and time-dependent (TD)DFT calculations have been carried out for [ReCl₃(dpk-N,N′)(OPPh₃)] and [ReOBr₃(dpk-OH), and their UV–vis spectra have been discussed on this basis.     

Strontium–copper selenite–chlorides: Synthesis and structural investigation

Two new complex selenite–chlorides of strontium and copper Sr₂Cu(SeO₃)₂Cl₂ (I) and SrCu₂(SeO₃)₂Cl₂ (II) were obtained and characterized by X-ray diffraction technique, DTA and IR spectroscopy. Both compounds crystallize in the monoclinic system I: Sp. gr. P2₁/n, a=5.22996(3) Å, b=6.50528(4) Å, c=12.34518(7) Å, β=91.3643(2)°, Z=2; II: Sp. gr. P2₁, a=7.1630(14) Å, b=7.2070(14) Å, c=8.0430(16) Å, β=95.92(3)°, Z=2. Comparison of the crystal structure of (I) with the structures of Sr₂M(SeO₃)₂Cl₂ (M=Co, Ni) was performed. The substitution of strontium atom in the structure of (I) by Cu²⁺ ion with a 3d⁹ Jahn–Teller distorted surrounding leads to the lowering of the structure symmetry and to the appearance of the noncentrosymmetric structure of (II). The noncentrosymmetric character of the structure of (II) was confirmed by SHG signal (1.2 units relative to an α-quartz powder sample).     

Crystal chemistry of three new monodimensional fluorometalates templated with ethylenediamine

Three new monodimensional hybrid metal (Ti, In, Al) fluorides are synthesized with ethylenediamine (en) as a templating agent in solvothermal conditions assisted by microwave heating. All structures involve inorganic chains built up from TiO₂F₄ octahedra connected by two opposite O²⁻ vertices in [H₂en]·(TiOF₄) (I), from InF₆(H₂O) pentagonal bipyramids linked by F–F edges in [H₂en]·(InF₄(H₂O))₂·H₂O (II) and from (Al₇F₃₀)⁹⁻ polyanions sharing two opposite AlF₆ octahedra in [H₂en]₃·(Al₆F₂₄) (III). I is tetragonal, P4/ncc, a = 12.761(3) Å, c = 8.041(3) Å; II is orthorhombic, F2dd, a = 6.904(5) Å, b = 16.559(5) Å, c = 19.777(4) Å and III is monoclinic, P2₁/n, a = 9.387(2) Å, b = 6.710(2) Å, c = 21.513(6) Å, β = 97.18(3)°.     

A manganese sulfite with extended metal–oxygen–metal bonds exhibiting hydrogen uptake

A manganese sulfite of the formula Mn₅(OH)₄(SO₃)₃·2H₂O, I{a=7.5759(7) Å, b=8.4749(8) Å, c=10.852(1) Å, β=100.732(2)°, Z=2, space group=P2₁/m (no. 11), R₁=0.0399 and wR₂=0.1121 [for R indexes I>2σ(I)]}, comprising Mn₃O₁₄ units and extended Mn–O–Mn bonds along the three dimensions has been synthesized under hydrothermal conditions. It has narrow channels along the b-axis and exhibits hydrogen storage of 2.1 wt% at 300 K and 134 bar.     

Recombination of KrD and XeD ions with electrons

Recombination rate coefficients of protonated and deuterated ions KrH⁺, KrD⁺, XeH⁺ and XeD⁺ were measured using Flowing Afterglow with Langmuir Probe (FALP). Helium at 1600 Pa and at temperature 250 K was used as a buffer gas in the experiments. Kr, Xe, H₂ and D₂ were introduced to a flow tube to form the desired ions. Because of small differences in proton affinities of Kr, D₂ and H₂ mixtures of ions, KrD⁺/D₃⁺ and KrH⁺/H₃⁺ are formed in the afterglow plasma, influencing the plasma decay. To obtain a recombination rate coefficient for a particular ion, the dependencies on partial pressures of gases used in the ion formation were measured. The obtained rate coefficients, α_KrD+(250 K) = (0.9 ± 0.3) × 10⁻⁸ cm³ s⁻¹ and α_XeD+(250 K) = (8 ± 2) × 10⁻⁸ cm³ s⁻¹ are compared with α_KrH+(250 K) = (2.0 ± 0.6) × 10⁻⁸ cm³ s⁻¹ and α_XeH+(250 K) = (8 ± 2) × 10⁻⁸ cm³ s⁻¹.     

Temperature dependence vapour pressure measurements of Mg(tmhd)2(tmeda) [(tmhd = 2,2,6,6-tetramethyl-3,5-heptanedione, tmeda = N,N,N′,N′-tetramethylethylenediamine]

The reaction between the magnesium β-diketonate complex Mg(tmhd)₂(H₂O)₂ and 1 equiv. of N,N,N′,N′-tetramethylethylenediamine (tmeda = Me₂NCH₂CH₂NMe₂) in hexane at room temperature yielded Mg(tmhd)₂(tmeda). The standard enthalpy of sublimation (83.2 ± 2.3 kJ mol⁻¹) and entropy of sublimation (263 ± 6.3 J mol⁻¹ K⁻¹) of Mg(tmhd)₂(tmeda) were obtained from the temperature dependence vapour pressure, determined by adopting a horizontal dual arm single furnace thermogravimetric analyser as a transpiration apparatus. From the observed melting point depression DTA, the standard enthalpy of fusion (58.3 ± 5.2 kJ mol⁻¹) was evaluated, using the ideal eutectic behaviour of Mg(tmhd)₂(tmeda) as a solvent with bis(2,4-pentanedionato)magnesium(II), Mg(acac)₂ as a non-volatile solute.