Polarization mechanism of LiNbO3 crystal due to thermoelectric power and current-induced electric fields during growth via micro-pulling-down method

The mechanism of polarization due to thermoelectric power and current-induced electric fields during the growth of LiNbO₃ crystals was studied using a micro-pulling-down method. With no applied electric current, a +c single-domain crystal was grown regardless of the domain orientation of the seed crystal. This +c domain growth was consistent with the direction of the electric field caused by the thermoelectric power in the liquid, despite an opposing electric field in the solid due to the opposite sign of the Seebeck coefficient. Thus, it was the electric field in the liquid that determined the domain structure of the growing crystal. On the other hand, when a current was applied from the melt to the crystal, a −c domain crystal was grown. The electric current required for this domain inversion to occur became larger as the temperature gradient in the solid phase decreased. This shows that the electric field in the solid phase became large enough to induce domain inversion from +c to −c through a combination of the thermoelectric power in the solid phase and current-induced electric field.     

Effect of BaO content on the sintering and physical properties of BaO-B2O3-SiO2 glasses

A BaO-B₂O₃-SiO₂ glass system was chosen as a candidate composition for the application to Pb-free low temperature sinterable glass. The effect of BaO content on the crystallization, sintering behavior, and properties of the glasses was examined. Both the glass transition temperature and crystallization temperature decreased as the BaO content increased. Crystallization easily occurred during sintering with a BaO content of more than 50 mol%, which effectively inhibited the over-firing phenomenon. The dielectric characteristics and thermal expansion coefficient of the glasses were examined and the results were explained on the basis of the crystallization and densification of the specimens.     

The dielectric behavior of a thermoelectric treated B2O3-Li2O-Nb2O5 glass

A transparent glass with the composition 60B₂O₃-30Li₂O-10Nb₂O₅ (mol%) was prepared by the melt-quenching technique. Glass-ceramics, containing LiNbO₃ ferroelectric crystallites, were obtained by heat-treatment (HT) above 500 °C, with and without the presence of an external electric field. The dielectric properties of the glass and glass-ceramic were investigated, as a function of temperature (270-315 K), in the 10 mHz-32 MHz frequency range. The presence of an external electric field, during the heating process, improves the formation of LiNbO₃ crystallites. The rise of the treatment temperature and the applied field, during the heat-treatment, leads to a decrease in the dc electric conductivity (σ_dc), indicating a decrease of the charge carriers number. The dielectric permittivity (ε′) values (300 K;1 kHz) are between 16.25 and 18.83, with the exception of the 550 °C HT sample that presents a ε′ value of 11.25. An electric equivalent circuit composed by an R in parallel with a CPE element was used to adjust the dielectric data. The results reflect the important role carried out by the heat-treatment and the electric field during the HT in the electric properties of glass-ceramics.     

Fabrication and properties of novel low-melting glasses in the ternary system ZnO-Sb2O3-P2O5

Glasses in the ternary system ZnO-Sb₂O₃-P₂O₅ were investigated as potential alternatives to lead based glasses for low temperature applications. The glass-forming region of ZnO-Sb₂O₃-P₂O₅ system has been determined. Structure and properties of the glasses with the composition (60 − x)ZnO-xSb₂O₃-40P₂O₅ were characterized by infrared spectra (IR), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results of IR indicated the role of Sb³⁺ as participant in glass network structure, which was supported by the monotonic and remarkable increase of density (ρ) and molar volume (V_M) with increasing Sb₂O₃ content. Glass transition temperature (T_g) and thermal stability decreased, and coefficient of thermal expansion (α) increased with the substitution of Sb₂O₃ for ZnO in the range of 0-50 mol%. XRD pattern of the heat treated glass containing 30 mol% Sb₂O₃ indicated that the structure of antimony-phosphate becomes dominant. The improved water durability of these glasses is consistent with the replacement of easily hydrated phosphate chains by corrosion resistant P-O-Sb bonds. The glasses containing ?30 mol% Sb₂O₃ possess lower T_g (<400 °C) and better water durability, which could be alternatives to lead based glasses for practical applications with further composition improvement.     

Physical properties of self-flux and WO3-containing solutions useful for growing type III KGd(PO3)4 single crystals

Density, surface tension and dynamic viscosity of self-flux and WO₃-containing solutions useful for growing type III KGd(PO₃)₄ single crystals have been measured at temperature near the saturation temperature. The thermal behavior of these physical properties has also been studied. Solutions containing WO₃ show a higher density than self-flux solutions and the density decreases linearly when the temperature increases, in the two cases. Near the saturation temperature, self-flux solutions present a surface tension slightly lower than that of WO₃-containing solutions. The dynamic viscosity of WO₃-containing solutions is slightly lower than that of self-flux solutions when this property was measured at the same temperature. We observed that, in WO₃-containing solutions, the saturation temperature is lower than in self-flux solutions. Thus, at the growth temperatures, the two solutions present dynamic viscosities only slightly different, so we expect that the introduction of WO₃ up to 10 mol% in the growth solution does not represent any important improvement in its hydrodynamics and this small change does not compensate for the possibility of introduction of tungsten impurities in the crystal structure affecting the physical properties expected for these crystals. Taking into account the values measured for these physical properties, we choose the initial conditions for growing type III KGd(PO₃)₄ single crystals from self-flux solutions.     

Spectroscopic properties of Er-doped Na2O-Sb2O3-B2O3-SiO2 glasses

Spectroscopic properties of Er³⁺-doped Na₂O-Sb₂O₃-B₂O₃-SiO₂ glasses have been investigated for developing 1.5-μm broadband fiber amplifiers. An intense 1.5-μm near infrared emission with a broad full width at half maximum (FWHM) of 88 nm has been obtained for Er³⁺-doped 5Na₂O-20Sb₂O₃-35B₂O₃-40SiO₂ glass upon excitation with a 980 nm laser diode. The obtained emission cross-section of the ⁴I_13/2 → ⁴I_15/2 transition and the lifetime of the ⁴I_13/2 level of Er³⁺ ions are 6.8 × 10⁻²¹ cm² and 0.36 ms, respectively. It is noted that the product of the emission cross-section and the FWHM of the glass, σ_e × FWHM, is as great as 598.4 × 10⁻²¹ cm² nm, which is comparable or higher than that of Er³⁺-doped bismuth-based and tellurite-based glasses. These special optical properties encourage in identifying them as important materials for potential applications in high performance optics and optical communication networks.     

Laser-induced crystallization of β′-RE2(MoO4)3 ferroelectrics (RE: Sm, Gd, Dy) in glasses and their surface morphologies

The glasses with the compositions of 21.25RE₂O₃-63.75MoO₃-15B₂O₃ (RE: Sm, Gd, Dy) were prepared and the formation of β′-RE₂(MoO₄)₃ ferroelectrics was confirmed in the crystallized glasses obtained through a conventional crystallization in an electric furnace. The features of the glass structure and crystallization behavior were clarified from measurements of Raman scattering spectra. Continuous-wave Nd:YAG laser with a wavelength of 1064 nm (laser power: 0.6-0.9 W, laser scanning speed: S = 1-16 μm/s) was irradiated to 10.625Sm₂O₃-10.625Gd₂O₃ (or Dy₂O₃)-63.75MoO₃-15B₂O₃ glasses, and the structural modification was induced at the glass surface. At the scanning speed of S = 10 μm/s, crystal lines consisting of β′-Gd_2−xSm_x(MoO₄)₃ or β′-Dy_2−xSm_x(MoO₄)₃ crystals were patterned on the glass surface. It was found that those crystal lines have the surface morphology with periodic bumps. At S = 1 μm/s, it was found that crystal lines consist of the mixture of paraelectric α-Gd_2−xSm_x(MoO₄)₃ and ferroelectric β′-Gd_2−xSm_x(MoO₄)₃ crystals, indicating the phase transformation from the β′ phase to the α phase during laser irradiation. Homogeneous crystal lines with β′-RE₂(MoO₄)₃ ferroelectrics have not been written in this study, but further research is continuing.     

Thermo-optic properties of B2O3 doped Li2O-Al2O3-SiO2 glass-ceramics

Reduction in the temperature coefficient of the optical path length, dS/dT of Li₂O-Al₂O₃-SiO₂ glass-ceramics with near-zero thermal expansion coefficient was attempted using control of the temperature coefficient of electronic polarizability, ?, and the thermal expansion coefficient, α. The dS/dT value of 2.6 mol% B₂O₃-doped glass-ceramic was 12.5  × 10⁻⁶/°C, which was 0.9 ×  10⁻⁶/°C smaller than that of B₂O₃-free glass-ceramic. On the other hand, reduction in dS/dT through B₂O₃ doping was not confirmed in precursor glasses. Results showed that reduction in dS/dT of the glass-ceramic through B₂O₃ doping is caused by the reduction in ?. The reduction in ? from B₂O₃ doping was probably attributable to numerical reduction in non-bridging oxide ions with larger ? value by the concentration of boron ions in the residual glass phase. In addition, application of hydrostatic pressure during crystallization was effective to inhibit precipitation of β-spodumene solid solution, which thereby decreases dS/dT. The dS/dT value of B₂O₃-doped glass-ceramic crystallized under 196 MPa was 11.7 ×  10⁻⁶/°C. That value was slightly larger than that of silica glass. The α value of this glass-ceramic was smaller than that of silica glass.     

Electron energy-loss spectroscopy in irradiation-sensitive rutile-GeO2

This report suggests that an electron energy-loss spectroscopy technique under low beam intensity is useful for beam-sensitive materials. High quality ‘damage-free’ Ge M₄₅ edge near-edge structure can be obtained using this method in rutile-GeO₂, which is susceptible to high-energy electron beam damage. Both experimental and theoretical results indicate that the Ge M₄₅ edge ELNES can be used to distinguish fourfold and sixfold coordinated Ge.     

Remark on the optical gap in ZnO-Bi2O3-TeO2 glasses

Four ZnO-Bi₂O₃-TeO₂ glasses were prepared from high purity (4N5) oxides. From measurements of the optical transmission on very thin bulk samples the optical gap was determined at around 3.55 eV for the glasses studied. The temperature dependence of the optical gap was also determined from the room temperature close up to 500 K. Preliminary Raman scattering measurements indicate that with a decrease in TeO₂ content, TeO₄ trigonal bipyramid transformation proceeds into TeO₃ trigonal pyramids.     

Spectroscopic properties of Er-Yb co-doped glass ceramics containing BaF2 nanocrystals

A Er³⁺ and Yb³⁺ co-doped transparent oxyfluoride glass ceramic containing BaF₂ nanocrystals has been prepared. The formation of BaF₂ nanocrystals in the glass ceramic was confirmed by X-ray diffraction. Intense upconversion luminescence in the Er³⁺ and Yb³⁺ co-doped glass ceramic could be observed. Stark splitting of the Er³⁺ upconversion luminescence peaks in the glass ceramic indicated that Er³⁺ and Yb³⁺ had been incorporated into the BaF₂ nanocrystals. Near infrared luminescence decay curves showed that the Er³⁺ and Yb³⁺ co-doped glass ceramic had higher luminescence efficiency than the precursor glass.     

Effect of N2/CH4 flow ratio on microstructure and composition of hydrogenated carbon nitride films prepared by a dual DC-RF plasma system

Hydrogenated carbon nitride (a-CN:H) films were deposited on n-type (1 0 0) silicon substrates making use of direct current radio frequency plasma enhanced chemical vapor deposition (DC-RF-PECVD), using a gas mixture of CH₄ and N₂ as the source gas in range of N₂/CH₄ flow ratio from 1/3 to 3/1 (sccm). The deposition rate, composition and bonding structure of the a-CN:H films were characterized by means of X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectrometry (FTIR). The mechanical properties of the deposited films were evaluated using nano-indentation test. It was found that the parameter for the DC-RF-PECVD process had significant effects on the growth rate, structure and properties of the deposited films. The deposition rate of the films decreased clearly, while the N/C ratio in the films increased with increasing N₂/CH₄ flow ratio. CN radicals were remarkably formed in the deposited films at different N₂/CH₄ flow ratio, and their contents are related to the nitrogen concentrations in the deposited films. Moreover, the hardness and Young’s modulus of the a-CN:H films sharply increased at first with increasing N₂/CH₄ flow ratio, then dramatically decreased with further increase of the N₂/CH₄ flow ratio, and the a-CN:H film deposited at 1/1 had the maximum hardness and Young’s modulus. In addition, the structural transformation from sp³-like to sp²-like carbon-nitrogen network in the deposited films also was revealed.     

Synthesis and characterization of visible light responsive N-TiO2 mixed crystal by a modified hydrothermal process

N doped TiO₂ with anatase and rutile mixed crystal were prepared by using tetrabutyl titanate as the precursor via a modified hydrothermal process and calcination at 320 °C. The microstructure and morphology of samples were characterized by XRD, UV-vis-DRS, FTIR and XPS. The results showed that N-TiO₂ particles were crystallized to anatase and rutile mixed crystal structure; they were presented narrow particle size distribution, and the average particle size was ca. 13.5 nm calculated from XRD results. It was found that the N-doped TiO₂ particles showed strong visible-light absorption and high photocatalytic activity for the mineralization of Rhodamine B under irradiation by visible light (400-500 nm). The high visible-light photocatalytic activity of the obtained N-doped TiO₂ might result from the synergetic effect of nitrogen doping and the mixed lattice structure of N-TiO₂. Possible mechanism of N-TiO₂ mixed crystal formed under hydrothermal conditions was discussed.     

A study of nonlinear optical properties in Bi2O3-WO3-TeO2 glasses

A series of bismuth tungsten tellurite glasses were prepared and their densities, linear refractive indices and transmission spectra were measured. The optical bandgaps E_opt and Urbach energies E_e of glasses were obtained from ultraviolet absorption edges. Both the optical gap (E_opt) and the band tail (E_e) are behaving oppositely. As the value of E_opt decreases with increasing WO₃ content, the degree of disorder increases which causes more defects or localized states resulting in deep localized in the bandgap with the tailing increased. Z-scan technique was carried out to investigate the third-order nonlinear optical properties of Bi₂O₃-WO₃-TeO₂ glasses. The third-order optical nonlinearity increases with decreasing the optical bandgap E_opt, since a increase of WO₃ content can provide the non-bridging oxygen ion content.     

Debye type dielectric relaxation in carbon nano-balls’ and 4-DMAABCA acid doped E7 coded nematic liquid crystal

The electrical properties of carbon nano-balls’ and 4-dimethylaminoazobenzene-2′-carboxylic acid doped dispersed nematic liquid crystal composite were investigated by impedance spectroscopy technique. The conductivity and capacitance were measured in the frequency range 100 kHz-1 MHz and temperature range 300-380 K. The loss peak was observed in the dielectric loss spectra and was identified as nearly-Debye type relaxation. Cole-Cole plots have been used to describe the characteristic changes of electrical properties in mentioned temperature interval. The sample presents monodispersive relaxation behavior with a relaxation time of ∼10⁻⁷ s. The relaxation process is attributed to the dipolar rotation of the long molecular axis and the activation energy is found to be 0.097 eV.     

Capacitance-voltage characteristics of In0.3Ge2Sb2Te5 thin films

The influence of indium doping on the capacitance variation with temperature and applied bias voltage of Ge₂Sb₂Te₅ is investigated. The capacitance-voltage (C-V) measurements of In_0.3Ge₂Sb₂Te₅ and Ge₂Sb₂Te₅ thin films were performed for a sweep of voltages from −20 to +20 V at different temperatures. The results show different capacitance behavior of In_0.3Ge₂Sb₂Te₅ and Ge₂Sb₂Te₅ films. As the temperature increases the capacitance of the indium-doped sample decreases and becomes negative. The negative capacitance effect might be attributed to a significant increase of the film’s conductivity due to temperature and applied bias voltage. The nonlinearity in the capacitance and conductivity could be related to the nucleation mechanism as the temperature becomes close to the amorphous-crystalline transition temperature.     

Sodium tracer diffusion in glasses of the type (CaO·Al2O3)x(2 SiO2)1−x

Tracer diffusion coefficients of the radioactive isotope Na-22 were measured in glasses of the type (CaO·Al₂O₃)_x(2 SiO₂)_1−x to study the diffusion of sodium as a function of glass composition, x, temperature and initial water content. The diffusion of Na-22 in glasses diffusion-annealed in dry air can always be well described by a single tracer diffusion coefficient, but sometimes not in samples annealed in common air. It was found that the sodium tracer diffusion coefficient decreases by about six orders of magnitude when the glass composition x changes from 0 to 0.75 at 800 °C. The temperature dependence of the diffusion of sodium seems to decrease as the silica content increases. Variations of the initial water content in some of the glasses investigated did not very significantly influence the rate of the tracer diffusion of sodium.     

Crystallization and dielectric properties of low temperature dielectrics containing Li2O filler

Crystallization and dielectric properties of typical low temperature co-fired ceramics (LTCC) consisting of calcium zinc aluminoborosilicate glass and Al₂O₃ filler were investigated by substituting the Al₂O₃ filler partially with Li₂O at the levels of 2-10 wt%. Depending on the content of Li₂O, densification was found significantly affected by early crystallization that resulted from the formation of unexpected crystalline phases including LiAlSiO₄, Ca₂SiO₄, LiAlO₂, and LiAlSi₃O₈. The effect of hindering sintering via earlier crystallization became enormous regardless of firing temperature when >5 wt% Li₂O substitution occurred. It was observed that the substitution of 2 wt% Li₂O for Al₂O₃ was beneficial in producing promising performance at the low temperature of 750 °C, which can be highlighted with k ∼ 8.7 and tan δ ∼ 0.009 at 1 MHz.     

Optical properties of and concentration quenching in Bi2O3-B2O3-Ga2O3 glasses

Er₂O₃-doped Bi₂O₃-B₂O₃-Ga₂O₃ glasses were prepared by the conventional melt-quenching method, and the Er³⁺:⁴I_13/2 → ⁴I_15/2 fluorescence properties are studied for different Er³⁺ concentrations. when the Er₂O₃ concentration increases from 0.03 to 3.0 mol%, the measured lifetime of Er³⁺:⁴I_13/2 level decrease from 2.24 to 0.9 m s, and from 0.25 to 0.20 m s for the Er³⁺:⁴I_11/2 level. The fast energy migration among Er³⁺ ions cause the reduction of lifetime of the ⁴I_13/2 level, whereas the change in the ⁴I_11/2 level is mainly due to a cooperative upconversion process (⁴I_11/2, ⁴I_11/2) → (⁴F_7/2, ⁴I_15/2). Based on the dipole-dipole interaction theory, the interaction parameter, C_Er,Er, for the migration rate of Er³⁺:⁴I_13/2 ↔ ⁴I_13/2 was calculated to be 32 × 10⁻⁴⁰ cm⁶ s⁻¹.     

Synthesis and Judd-Ofelt analysis of a sol-gel material doped with a Ln2(Benzoate)6(Phen)2 (Ln = Er/Yb) complex

In this work, we have prepared a sol-gel derived hybrid material directly doped with Er_1.4Yb_0.6(Benzoate)₆(Phen)₂ (Phen = 1,10-phenanthroline) complex, which was reported with intramolecular Yb-Er energy-transfer process in our previous work. The infrared (IR) spectra of the pure complex and hybrid gel material were investigated. The NIR photoluminescence (PL) spectrum of hybrid gel material shows strong characteristic emission of Er³⁺ with broad full width at half-maximum (FWHM) of 70 nm. Judd-Ofelt theory was used in order to analyze the optical properties of Er³⁺ ions in the hybrid gel material.