Phase separation of gas–liquid and liquid–liquid microflows in microchips

Phase separation of gas–liquid and liquid–liquid microflows in microchannels were examined and characterized by interfacial pressure balance. We considered the conditions of the phase separation, where the phase separation requires a single phase flow in each output of the microchannel. As the interfacial pressure, we considered the pressure difference between the two phases due to pressure loss in each phase and the Laplace pressure generated by the interfacial tension at the interface between the separated phases. When the pressure difference between the two phases is balanced by the Laplace pressure, the contact line between the two phases is static. Since the contact angle characterizing the Laplace pressure is restricted to values between the advancing and receding contact angles, the Laplace pressure has a limit. When the pressure difference between the two phases exceeds the limiting Laplace pressure, one of the phases leaks into the output channel of the other phase, and the phase separation fails. In order to experimentally verify this physical picture, microchips were used having a width of 215 μm and a depth of 34 μm for the liquid–liquid microflows, a width of 100 μm and a depth of 45 μm for the gas–liquid microflows. The experimental results of the liquid–liquid microflows agreed well with the model whilst that of the gas–liquid microflows did not agree with the model because of the compressive properties of the gas phase and evaporation of the liquid phase. The model is useful for general liquid–liquid microflows in continuous flow chemical processing.     

Evolution of dispersive liquid–liquid microextraction method

Dispersive liquid–liquid microextraction (DLLME) has become a very popular environmentally benign sample-preparation technique, because it is fast, inexpensive, easy to operate with a high enrichment factor and consumes low volume of organic solvent. DLLME is a modified solvent extraction method in which acceptor-to-donor phase ratio is greatly reduced compared with other methods. In this review, in order to encourage further development of DLLME, its combination with different analytical techniques such as gas chromatography (GC), high-performance liquid chromatography (HPLC), inductively coupled plasma-optical emission spectrometry (ICP-OES) and electrothermal atomic absorption spectrometry (ET AAS) will be discussed. Also, its applications in conjunction with different extraction techniques such as solid-phase extraction (SPE), solidification of floating organic drop (SFO) and supercritical fluid extraction (SFE) are summarized. This review focuses on the extra steps in sample preparation for application of DLLME in different matrixes such as food, biological fluids and solid samples. Further, the recent developments in DLLME are presented. DLLME does have some limitations, which will also be discussed in detail. Finally, an outlook on the future of the technique will be given.     

Automated apparatus for the rapid determination of liquid–liquid and solid–liquid phase transitions

An automated apparatus developed for the determination of liquid–liquid and solid–liquid equilibrium temperatures with a resolution of 1 mK and a traceable accuracy of 0.01 K is described. The amount of light transmitted through six sample cells placed in a computer controlled thermostat is recorded at heating or cooling rates from 0.075 to 15 K h⁻¹. The construction does not require expensive optic equipment like lasers, glass fibre optics or photomultipliers, but is based on light emitting diodes (LED) as light sources and light dependent resistors (LDR) or photodiodes as detectors. As shown by the discussed examples, the instrument has a wide range of possible applications from the investigation of simple one-component and binary systems to the study of the complicated phase behavior of surfactant solutions.     

Dynamics of liquid–liquid demixing: mesoscopic simulations of polymer solutions

In this article, the mesoscopic simulation method dissipative particle dynamics (DPD) is applied to study the dynamics of polymer–solvent liquid–liquid phase separation. It will be shown that the degree of branching has a pronounced effect on the radius of gyration and the centre of mass diffusion of the polymer. Based on the simulation results it can be concluded that the difference in chemical potential between the mixed and the demixed state is the main driving force behind the centre of mass diffusion (and thus phase separation), rather than the reduced radius of gyration due to to polymer chain collapse.     

Determination of triazines in honey by dispersive liquid–liquid microextraction high-performance liquid chromatography

Dispersive liquid–liquid microextraction (DLLME) high-performance liquid chromatography (HPLC) was developed for extraction and determination of triazines from honey. A room temperature ionic liquid, 1-hexyl-3-methylimidazolium hexafluorophosphate [C₆MIM][PF_6.], was used as extraction solvent and Triton X 114 was used as dispersant. A mixture of 175 μL [C₆MIM][PF₆] and 50 μL 10% Triton X 114 was rapidly injected into the 20 mL honey sample by syringe. After extraction, phase separation was performed by centrifugation and the sedimented phase was analyzed by HPLC. Some experimental parameters, such as type and volume of extraction solvent, concentration of dispersant, pH value of sample solution, salt concentration and extraction time were investigated and optimized. The detection limits for chlortoluron, prometon, propazine, linuron and prebane are 6.92, 5.84, 8.55, 8.59 and 5.31 μg kg⁻¹, respectively. The main advantages of the proposed method are simplicity of operation, low cost, high enrichment factor and extraction solvent volume at microliter level. Honey samples were analyzed by the proposed method and obtained results indicated that the proposed method provides acceptable recoveries and precisions.     

Lipophilic ternary complexes in liquid–liquid extraction of trivalent lanthanides

The formation of ternary complexes between lanthanide ions [Nd(III) or Eu(III)], octyl(phenyl)-N,N-diisobutyl-carbamoylmethylphosphine oxide (CMPO), and bis-(2-ethylhexyl)phosphoric acid (HDEHP) was probed by liquid–liquid extraction and spectroscopic techniques. Equilibrium modeling of data for the extraction of Nd(III) or Eu(III) from lactic acid media into n-dodecane solutions of CMPO and HDEHP indicates the predominant extracted species are of the type [Ln(AHA)₂(A)] and [Ln(CMPO)(AHA)₂(A)], where Ln?=?Nd or Eu and A represents the DEHP^? anion. FTIR (for both Eu and Nd) and visible spectrophotometry (in the case of Nd) indicate the formation of the [Ln(CMPO)(A)₃] complexes when CMPO is added to n-dodecane solutions of the LnA₃ compounds. Both techniques indicate a stronger propensity of CMPO to complex Nd(III) versus Eu(III).     

Comparison of dispersive liquid–liquid microextraction and hollow fiber liquid–liquid–liquid microextraction for the determination of fentanyl,alfentanil, and sufentanil in water and biological fluids by high-performance liquid chromatography

Dispersive liquid–liquid microextraction (DLLME) and hollow fiber liquid–liquid–liquid microextraction (HF-LLLME) combined with HPLC–DAD have been applied for the determination of three narcotic drugs (alfentanil, fentanyl, and sufentanil) in biological samples (human plasma and urine). Different DLLME parameters influencing the extraction efficiency such as type and volume of the extraction solvent and the disperser solvent, concentration of NaOH, and salt addition were investigated. In the HF-LLLME, the effects of important parameters including organic solvent type, concentration of NaOH as donor solution, concentration of H₂SO₄ as acceptor phase, salt addition, stirring rate, temperature, and extraction time were investigated and optimized. The results showed that both extraction methods exhibited good linearity, precision, enrichment factor, and detection limit. Under optimal condition, the limits of detection ranged from 0.4 to 1.9 μg/L and from 1.1 to 2.3 μg/L for DLLME and HF-LLLME, respectively. For DLLME, the intra- and inter-day precisions were 1.7–6.4% and 14.2–15.9%, respectively; and for HF-LLLME were 0.7–5.2% and 3.3–10.1%, respectively. The enrichment factors were from 275 to 325 and 190 to 237 for DLLME and HF-LLLME, respectively. The applicability of the proposed methods was investigated by analyzing biological samples. For analysis of human plasma and urine samples, HF-LLLME showed higher precision, more effective sample clean-up, higher extraction efficiency, lower organic solvent consumption than DLLME.     

Viscosity of liquid Cu–Sn alloys

We investigated of the kinematic viscosity of liquid Cu–Sn alloys upon heating and subsequent cooling by the method of the oscillating cylinder. For the liquids alloys Cu75Sn25, Cu50Sn50, Cu48Sn52, Cu32Sn68, and Cu17Sn83, the temperature dependencies of the viscosity upon heating deviate from the Arrhenius relation. The temperature dependencies of viscosity show the Arrhenius-like behaviour upon cooling for all investigated alloys. A discrepancy between the temperature dependencies of viscosity obtained upon heating and cooling arised. We built the concentration dependences of the kinematic viscosity of liquid Cu–Sn alloys upon cooling. The increase of the values of viscosity and activation energy of viscous flow in the concentration range corresponding to the existence of intermetallic compounds Cu₃Sn in the solid state was observed. These results were qualitatively interpreted using the concept of microheterogeneities of liquid alloys.     

Dispersive liquid–liquid–liquid microextraction combined with liquid chromatography for the determination of chlorophenoxy acid herbicides in aqueous samples

A novel sample preparation method “Dispersive liquid–liquid–liquid microextraction” (DLLLME) was developed in this study. DLLLME was combined with liquid chromatography system to determine chlorophenoxy acid herbicide in aqueous samples. DLLLME is a rapid and environmentally friendly sample pretreatment method. In this study, 25 μL of 1,1,2,2-tetrachloroethane was added to the sample solution and the targeted analytes were extracted from the donor phase by manually shaking for 90 s. The organic phase was separated from the donor phase by centrifugation and was transferred into an insert. Acceptor phase was added to this insert. The analytes were then back-extracted into the acceptor phase by mixing the organic and acceptor phases by pumping those two solutions with a syringe plunger. After centrifugation, the organic phase was settled and removed with a microsyringe. The acceptor phase was injected into the UPLC system by auto sampler. Fine droplets were formed by shaking and pumping with the syringe plunger in DLLLME. The large interfacial area provided good extraction efficiency and shortened the extraction time needed. Conventional LLLME requires an extraction time of 40–60 min; an extraction time of approximately 2 min is sufficient with DLLLME. The DLLLME technique shows good linearity (r² ≥ 0.999), good repeatability (RSD: 4.0–12.2% for tap water; 5.7–8.5% for river water) and high sensitivity (LODs: 0.10–0.60 μg/L for tap water; 0.11–0.95 μg/L for river water).     

Simultaneous determination of several phytohormones in natural coconut juice by hollow fiber-based liquid–liquid–liquid microextraction-high performance liquid chromatography

A simple, selective, sensitive and inexpensive method of hollow fiber-based liquid–liquid–liquid microextraction (HF-LLLME) combined with high performance liquid chromatography (HPLC)-ultraviolet (UV) detection was developed for the determination of four acidic phytohormones (salicylic acid (SA), indole-3-acetic acid (IAA), (±) abscisic acid (ABA) and (±) jasmonic acid (JA)) in natural coconut juice. To the best of our knowledge, this is the first report on the use of liquid phase microextraction (LPME) as a sample pretreatment technique for the simultaneous analysis of several phytohormones. Using phenetole to fill the pores of hollow fiber as the organic phase, 0.1 mol L⁻¹ NaOH solution in the lumen of hollow fiber as the acceptor phase and 1 mol L⁻¹ HCl as the donor phase, a simultaneous preconcentration of four target phytohormones was realized. The acceptor phase was finally withdrawn into the microsyringe and directly injected into HPLC for the separation and quantification of the target phytohormones. The factors affecting the extraction efficiency of four phytohormones by HF-LLLME were optimized with orthogonal design experiment, and the data was analyzed by Statistical Product and Service Solutions (SPSS) software. Under the optimized conditions, the enrichment factors for SA, IAA, ABA and JA were 243, 215, 52 and 48, with the detection limits (S/N = 3) of 4.6, 1.3, 0.9 ng mL⁻¹ and 8.8 μg mL⁻¹, respectively. The relative standard deviations (RSDs, n = 7) were 7.9, 4.9, 6.8% at 50 ng mL⁻¹ level for SA, IAA, ABA and 8.4% at 500 μg mL⁻¹ for JA, respectively. To evaluate the accuracy of the method, the developed method was applied for the simultaneous analysis of several phytohormones in five natural coconut juice samples, and the recoveries for the spiked samples were in the range of 88.3–119.1%.     

The influence of the temperature on the liquid–liquid equilibrium of the ternary system 1-pentanol–ethanol–water

Liquid–liquid equilibrium data for the ternary system 1-pentanol–ethanol–water have been determined experimentally at 25, 50, 85 and 95°C. These results have been correlated simultaneously by the uniquac method obtaining two sets of interaction parameters: one of them independent of the temperature and the other with a linear dependence. Both sets of parameters fit the experimental results well.     

Support-free pulsed liquid–liquid chromatography

A simple technique of support-free liquid–liquid chromatography is suggested that operates without incorporation of a centrifuge. The pulsed chromatography apparatus consists of a stationary coiled tube and a pulsation device to produce reciprocating motion of liquid phases within each individual coil segment. This reciprocating motion generates a centrifugal force field varying in intensity and direction that leads to an improved mixing of the two liquid phases and retains the stationary phase in the coiled tubing. The intensity of the back and forth motion of liquid phases within each coil unit can be varied by varying the frequency and/or the amplitude of the pulsations generated by the pulsation device. As the magnitude of the stationary phase retention is of paramount importance for success of the technique, the retention of the stationary phase in the pulsed coil column was experimentally studied. A few experiments were conducted to test the chromatographic behavior of valeric (n-pentanoic) and caproic (n-hexanoic) acids. The results obtained demonstrate the potential of the new separation method for preparative purposes.     

Ionic liquid based dispersive liquid–liquid microextraction for the extraction of pesticides from bananas

This paper describes a dispersive liquid–liquid microextraction (DLLME) procedure using room temperature ionic liquids (RTILs) coupled to high-performance liquid chromatography with diode array detection capable of quantifying trace amounts of eight pesticides (i.e. thiophanate-methyl, carbofuran, carbaryl, tebuconazole, iprodione, oxyfluorfen, hexythiazox and fenazaquin) in bananas. Fruit samples were first homogenized and extracted (1 g) with acetonitrile and after suitable evaporation and reconstitution of the extract in 10 mL of water, a DLLME procedure using 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) as extraction solvent was used. Experimental conditions affecting the DLLME procedure (sample pH, sodium chloride percentage, ionic liquid amount and volume of disperser solvent) were optimized by means of an experimental design. In order to determine the presence of a matrix effect, calibration curves for standards and fortified banana extracts (matrix matched calibration) were studied. Mean recovery values of the extraction of the pesticides from banana samples were in the range of 69–97% (except for thiophanate-methyl and carbofuran, which were 53–63%) with a relative standard deviation lower than 8.7% in all cases. Limits of detection achieved (0.320–4.66 μg/kg) were below the harmonized maximum residue limits established by the European Union (EU). The proposed method, was also applied to the analysis of this group of pesticides in nine banana samples taken from the local markets of the Canary Islands (Spain). To the best of our knowledge, this is the first application of RTILs as extraction solvents for DLLME of pesticides from samples different than water.     

Alkylsulfate-based ionic liquids in the liquid–liquid extraction of aromatic hydrocarbons

The (liquid + liquid) equilibrium data (LLE) for the extraction of toluene from heptane with different ionic liquids (ILs) based on the alkylsulfate anion (R-SO₄) was determined at T = 313.2 K and atmospheric pressure. The effect of more complex R-SO₄ anions on capacity of extraction and selectivity in the liquid–liquid extraction of toluene from heptane was studied. The ternary systems were formed by {heptane + toluene + 1,3-dimethylimidazolium methylsulfate ([mmim][CH₃SO₄]), 1-ethyl-3-methylimidazolium hydrogensulfate ([emim][HSO₄]), 1-ethyl-3-methylimidazolium methylsulfate ([emim][CH₃SO₄]), or 1-ethyl-3-methylimidazolium ethylsulfate ([emim][C₂H₅SO₄])}. The degree of quality of the experimental LLE data was ascertained by applying the Othmer–Tobias correlation. The phase diagrams for the ternary systems were plotted, and the tie lines correlated with the NRTL model compare satisfactorily with the experimental data.     

Measuring the optical chirality of molecular aggregates at liquid–liquid interfaces

Some new experimental methods for measuring the optical chirality of molecular aggregates formed at liquid–liquid interfaces have been reviewed. Chirality measurements of interfacial aggregates are highly important not only in analytical spectroscopy but also in biochemistry and surface nanochemistry. Among these methods, a centrifugal liquid membrane method was shown to be a highly versatile method for measuring the optical chirality of the liquid–liquid interface when used in combination with a commercially available circular dichroism (CD) spectropolarimeter, provided that the interfacial aggregate exhibited a large molar absorptivity. Therefore, porphyrin and phthalocyanine were used as chromophoric probes of the chirality of itself or guest molecules at the interface. A microscopic CD method was also demonstrated for the measurement of a small region of a film or a sheet sample. In addition, second-harmonic generation and Raman scattering methods were reviewed as promising methods for detecting interfacial optical molecules and measuring bond distortions of chiral molecules, respectively.     

Extraction of pesticides in water samples using vortex-assisted liquid–liquid microextraction

A simple solvent microextraction method termed vortex-assisted liquid–liquid microextraction (VALLME) coupled with gas chromatography micro electron-capture detector (GC-μECD) has been developed and used for the pesticide residue analysis in water samples. In the VALLME method, aliquots of 30 μL toluene used as extraction solvent were directly injected into a 25 mL volumetric flask containing the water sample. The extraction solvent was dispersed into the water phase under vigorously shaking with the vortex. The parameters affecting the extraction efficiency of the proposed VALLME such as extraction solvent, vortex time, volumes of extraction solvent and salt addition were investigated. Under the optimum condition, enrichment factors (EFs) in a range of 835–1115 and limits of detection below 0.010 μg L⁻¹ were obtained for the determination of target pesticides in water. The calculated calibration curves provide high levels of linearity yielding correlation coefficients (r²) greater than 0.9958 with the concentration level ranged from 0.05 to 2.5 μg L⁻¹. Finally, the proposed method has been successfully applied to the determination of pesticides from real water samples and acceptable recoveries over the range of 72–106.3% were obtained.     

Voltammetric determination of perchlorate ion at a liquid–liquid microscopic interface

A method is proposed for the electrochemical determination of perchlorate ion by voltammetry at the interface between two immiscible phases (water–o-nitrophenyl octyl ether). A demountable original-design amperometric ion-selective electrode based on a laser-microperforated polymeric membrane was fabricated for voltammetric measurements. The conditions of analytical signal recording in the determination of ClO₄ ^? were determined. The effect of interfering ions was assessed and amperometric selectivity coefficients were calculated. The accuracy of the procedure was verified by the added–found method. The developed electrode was applied to the determination of perchlorate in natural and drinking waters.     

Electrosynthesis of polyphenylpyrrole coated silver particles at a liquid–liquid interface

This communication reports the production of polyphenylpyrrole coated silver nanoparticles at the liquid/liquid interface by an EC-type mechanism. In the electrochemical step of the reaction N-phenylpyrrole facilitates the transfer of the silver ion from an aqueous to an organic phase. This step is followed by a slow homogeneous electron transfer reaction from the N-phenylpyrrole to the silver ion followed by polymerization and metal cluster growth.