Development of an on-line isotope dilution laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) method for determination of boron in silicon wafers

A method has been developed based on an on-line isotope dilution technique couple with laser ablation/inductively coupled plasma mass spectrometry (LA-ICP-MS), for the determination of boron in p-type silicon wafers. The laser-ablated sample aerosol was mixed on-line with an enriched boron aerosol supplied continuously using a conventional nebulization system. Upon mixing the two aerosol streams, the isotope ratio of boron changed rapidly and was then recorded by the ICP-MS system for subsequent quantification based on the isotope dilution principle. As an on-line solid analysis method, this system accurately quantifies boron concentrations in silicon wafers without the need for an internal or external solid reference standard material. Using this on-line isotope dilution technique, the limit of detection for boron in silicon wafers is 2.8 × 10¹⁵ atoms cm⁻³. The analytical results obtained using this on-line methodology agree well with those obtained using wet chemical digestion methods for the analysis of p-type silicon wafers containing boron concentrations ranging from 1.0 × 10¹⁶ to 9.6 × 10¹⁸ atoms cm⁻³.     

Fully automated column-switching HPLC determination of aflatoxin M1 in milk using dialysis as sample preparation

A procedure has been developed for the automated determination of aflatoxin M1 in decreamed milk, by using on-line dialysis and subsequent trace enrichment on a reverse phase column. After foreflush to the analytical column the determination is performed with fluorescence detection. Fully automated analysis within 10 min is thus possible with reproducible dialysis recoveries above 50% (CV is 3.3%, n = 20) and detection levels of 50 ng/kg.     

Analysis of nitrated polycyclic aromatic hydrocarbons by liquid chromatography with fluorescence and mass spectrometry detection: air particulate matter, soot, and reaction product studies

Polycyclic aromatic hydrocarbons (PAH) and their nitrated derivatives (nitro-PAH) are environmental pollutants which pose a threat to human health even at low concentration levels. In this study, efficient analytical methods for the analysis of nitro-PAH and PAH (extraction, clean-up, chromatographic separation, and spectrometric detection) have been developed, characterized, and applied to aerosol samples. The separation and quantification of 12 nitro-PAH was carried out by reversed-phase high performance liquid chromatography (HPLC), on-line reduction, and fluorescence detection. The detection limits were in the range of 0.03–0.5 g L^–1 (6–100 pg in the investigated sample aliquots), and the recovery rates from soot samples were 70–90%. Nitro-PAH and PAH concentrations have been determined for different types of soot and for urban, rural, and alpine fine air particulate matter (PM2.5). For the first time, trace amounts of nitro-PAH have been detected in a high-alpine clean air environment. The on-line reduction and fluorescence technique has been complemented by atmospheric pressure chemical ionization time-of-flight mass spectrometry (APCI-TOF-MS). The MS detection allowed the analysis of partially nitrated and oxygenated PAH in laboratory studies of the heterogeneous reaction of PAH on soot and glass fiber substrates with gaseous nitrogen oxides and ozone. It led to the tentative identification of a previously unknown nitrated derivative of the particularly toxic PAH benzo[a]pyrene (BaP-nitroquinone), and provides the first experimental evidence that PAH-nitroquinones can be formed by reaction of PAH with atmospheric photooxidants.     

Quantitative determination of saturated oligogalacturonic acids in enzymatic digests of polygalacturonic acid,pectin and carrot pomace by on-line LC-ESI-MS

A method for the quantitative determination of oligogalacturonic acids (OGAs) by on-line high-performance liquid chromatographic (HPLC) separation and mass spectrometric detection via an electrospray interface (ESI-MS) without additional desalting steps was developed. Saturated OGAs up to a degree of polymerization (dp) of 3 were quantified by comparison with reference compounds. The calibration plots showed high linearity (R²>0.99), and the detection limits for dp 1, 2, and 3 were 11, 28, and 6 ng per injection, respectively. Non- and partially methyl-esterified OGAs with a dp of 3 and 4 were calculated semi-quantitatively as dp 3. The analytical system was used for the quantification of OGAs of digests obtained by incubation of polygalacturonic acid, pectin, and carrot pomace with commercial enzyme preparations. Furthermore, methyl-esterified OGAs up to a dp of 12 containing up to 4 methyl esters were detected in a pectin digest.     

Automated high-performance liquid chromatographic determination of amphetamine in biological fluids using column-switching and on-column derivatization

Summary A rapid and simple liquid-chromatographic method has been developed for on-line quantification of amphetamine in biological fluids. Untreated samples (20 μL) are injected directly into the chromatographic system and purified on a 20 mm×2.1 mm i.d. pre-column packed with 30 μm Hypersil C₁₈ stationary phase. After clean-up the analyte is transferred to the analytical column (125 mm×4 mm i.d., 5 μm LiChrospher 100 RP₁₈) for derivatization and separation using a mixture of acetonitrile and the derivatization reagent (o-phthaldialdehyde andN-acetyl-L-cysteine) as the mobile phase. The experimental conditions for on-line derivatization and resolution of the amphetamine have been optimized, and the results have been compared with those obtained by derivatizing the analyte in pre-column mode. The method described has been applied to the determination of amphetamine in plasma and urine. Good linearity and reproducibility were obtained in the 0.1–10.0 μg mL⁻¹ concentration range, and limits of detection were 25 ng mL⁻¹ and 10 ng mL⁻¹ with UV and fluorescence detection, respectively. The procedure described is very simple and rapid, because no off-line manipulation of the sample is required; the total analysis time is approximately 8 min.     

Microwave-assisted on-line derivatization for sensitive flow injection fluorometric determination of formaldehyde in some foods

A rapid and sensitive flow injection fluorometry has been developed for the determination of formaldehyde based on the microwave on-line accelerating its Hantzsch reaction with cyclohexane-1,3-dione. Under the optimized conditions, the fluorescent intensity is proportional to formaldehyde content in the range from 0.05 ng/mL to 2.000 μg/mL. The detection limit (S/N = 3) is 0.02 ng/mL and the analytical frequency is 28 injections per hour. The relative standard deviations are 2.2% and 3.1% for eleven injections of 0.100 and 0.001 μg/mL of formaldehyde, respectively. With the assistance of microwave irradiation, a best sensitive fluorometry was established for the determination of formaldehyde at a high analytical frequency. This method was successfully applied to food analysis without requiring any sample pretreatment, and the determination results were correlated well with those obtained by the standard method with a sample pretreatment of steam distillation.     

Kinetic On-line Evaluation of Chemical Reactions

A computer program was developed for kinetic evaluations of calorimetric experiments to predict the further reaction run under adiabatic conditions. Kinetic modeling is based on elementary reaction steps whose rate laws form a set of differential equations. For the continuous parameter optimization time-temperature data and their derivatives are used. A special calorimeter of the ACTRON series with safety equipment was applied to investigate the kinetics of chemical reactions and to test kinetic on-line evaluations. In the paper, examples for the reaction of n-propanol with o-chlornitrobenzene and for the alcoholysis of phenyl isocyanate are given.This revised version was published online in November 2005 with corrections to the Cover Date.     

In-capillary micro solid-phase extraction and capillary electrophoresis separation of heterocyclic aromatic amines with nanospray mass spectrometric detection

A miniaturised technique to analyse and detect heterocyclic aromatic amines (HAs) using micro solid-phase extraction (SPE) coupled on-line (in-capillary) to capillary electrophoresis (CE) separation with nanospray (nESI) mass spectrometry (MS) detection has been developed. HAs are mutagenic and carcinogenic compounds formed at low levels in protein-rich food during cooking. Due to the low concentrations of HAs and the high complexity of the matrix in which they exist, sensitive and selective analytical methods are required for quantification. SPE was performed on a packed bed of C₁₈ particles inside the CE capillary, which minimised the dead volume. The on-line coupling of SPE, CE and nESI-MS reduced the time for extraction and identification to less than half an hour, which will allow for screening of several samples per day. The new technique provides short analysis time, low sample and solvent consumption, and HAs in standard solutions were easily detected at 12–17 fmol injections, and in spiked urine samples at 750–810 fmol injections.     

Synthesis and Functionalization of 3-Ethylquinoxalin-2(1<Emphasis Type="Italic">H</Emphasis>)-one

A new and effective procedure was developed for the synthesis of 3-ethylquinoxalin-2(1H)-one from o-phenylenediamine and ethyl 2-oxobutanoate. The latter was prepared by the Grignard reaction of diethyl oxalate with ethylmagnesium bromide or iodide. The ethyl group in 3-ethylquinoxalin-2(1H)-one can readily be converted into various functional groups: α-bromoethyl, α-thiocyanato, α-azidoethyl, α-phenylaminoethyl, acetyl, and bromoacetyl. The reaction of 3-(bromoacetyl)quinoxalin-2(1H)-one with thiourea and hydrazine-1,2-dicarbothioamide gives the corresponding 3-(2-amino-4-thiazolyl) derivatives.__________Translated from Zhurnal Organicheskoi Khimii, Vol. 41, No. 4, 2005, pp. 609–616.Original Russian Text Copyright © 2005 by Mamedov, Kalinin, Gubaidullin, Isaikina, Litvinov.     

Determination of trace platinum by supramolecular catalytic kinetic spectrofluorimetry of β–cyclodextrin–platinum–KBrO3–salicylaldehyde furfuralhydrazone

A supramolecular catalytic kinetic spectrofluorimetric method was developed for the determination of platinum(IV) and the possible mechanism of catalytic reaction was discussed. The method was based on the fluorescence-enhancing reaction of salicylaldehyde furfuralhydrazone (SAFH) with potassium bromate, which was catalysed by platinum(IV) in a water–ethanol medium. β–Cyclodextrin (β-CD) obviously sensitized the determination at pH 5.20 and 25°C. Under optimum conditions, the β-CD–platinum–KBrO₃–SAFH supramolecular kinetic catalytic reaction system had excitation and emission maxima at 372 and 461 nm, respectively. The linear range of this method was 0.60–180 ng ml⁻¹ with a relative standard deviation of 1.2%, and the detection limit was 0.18 ng ml⁻¹. Investigation of the mechanism and the effects of interferences is presented. The proposed method was applied successfully to determine trace platinum(IV) in the chemotherapeutic drug cisplatin and serum from patients with satisfactory results.      

Antimony determination and speciation by multisyringe flow injection analysis with hydride generation-atomic fluorescence detection

A new analytical procedure for determination of inorganic antimony and speciation of antimony(III) and antimony(V) is presented. For this purpose, a software-controlled time-based multisyringe flow injection system, which contains a multisyringe burette provided with a multi-port selection valve, was developed. Hydride generation-atomic fluorescence spectrometry was used as a detection technique. A 0.3% (w/v) reducing sodium tetrahydroborate solution, hydrochloric acid (2 M), an antimony solution and a pre-reducing solution of 10% (w/v) KI and 0.3% (w/v) ascorbic acid are dispensed simultaneously into a gas-liquid separation cell with further propulsion of the reaction product into the flame of an atomic fluorescence spectrometer using argon flow. A hydrogen flow was employed to support the flame.The linear range and the detection limit (3s_b/S) of the proposed technique were 0.2-5.6 μg l⁻¹ and 0.08 μg l⁻¹, respectively. A sample throughput of 18 samples per hour (corresponding to 80 injections per hour) was achieved. The relative standard deviation for 18 independent measurements was 4.6%. This technique was validated by means of reference solid and water materials with good agreement with the certified values. Satisfactory results for speciation of Sb(III) and Sb(V) by means of the developed technique were obtained.     

Determination of ultratrace levels of dissolved metals in seawater by reaction cell inductively coupled plasma mass spectrometry after ammonia induced magnesium hydroxide coprecipitation

A method for the determination of ultratrace amounts of Cr, Fe, Mn, Pb and Zn in seawater has been developed. It combined the low-blank magnesium hydroxide coprecipitation procedure with quadrupole inductively coupled plasma mass spectrometry and used the dynamic reaction cell technique to resolve the polyatomic interferences arising from the residual matrix, the solvent and plasma gases. Detection limits (3σ_B, n = 10) for Cr, Fe, Mn, Pb and Zn were 0.02, 0.10, 0.01, 0.002 and 0.19 nM, respectively, using 50 mL of seawater sample. The accuracy of the analytical procedure was verified by the analysis of the seawater reference materials CASS-4, NASS-5, SAFe D2 and SAFe S. The analytical precision ranged from 3% to 16% (n = 6), with a sample throughput of about 6 samples h⁻¹.     

On-line analysis of volatile fatty acids in anaerobic treatment processes

In this paper, an on-line spectrofluorimetric system is proposed for a simple, rapid and accurate measurement of volatile fatty acids (VFA) in anaerobic treatment processes. The determination method is based on the derivatization of VFA with N-(1-naphthyl)ethylenediamine (EDAN) followed by a spectrofluorimetric detection of the corresponding amide. The analytical procedure is automated with a flow analysis technique, coupling multisyringe (MSFIA) and multi-pumping (MPFS) methods. Operative conditions have been investigated with a special attention paid to the activation and amidation steps and to the liquid-liquid extraction of the derivatized final product. Fluorescence intensities (λ_em = 335 nm, λ_ex = 395 nm) were found to be proportional to the concentration of VFA, expressed as acetic equivalent, in the range 19-1000 mg L⁻¹, with a detection limit (3σ) of 5.1 mg L⁻¹. Our results showed a good selectivity for VFA as compared to other organic and inorganic compounds usually found in sewage sludges. Validation of the on-line system developed has been assessed by application of the procedure to aqueous samples originating from sewage sludge treatment plants. The results were in good agreement with ion chromatography measurements.     

On-line preconcentration and GFAAS determination of trace metals in waters

An on-line separation preconcentration system coupled to electrothermal (graphite furnace) atomic absorption spectrometry was developed. A miniature column packed with iminodiacetic acid ethyl cellulose (IDAEC) was inserted into the loop. A peristaltic pump was used to deliver solutions. A flow of air was driven into the packed column, evacuating it between sample loading, washing and elution. The retained analyte was introduced on-line to graphite furnace using countercurrent elution with HNO₃. The system was applied for the determination of V, Co and Pb in medicinal mineral water samples, and nickel in sea water samples. The detection limits (3σ) were 0.058, 0.022, 0.067, 0.062 μg/l for Co, Pb, V, and Ni, respectively. The R.S.D. (n=5) was <5% at 0.4–1.0 μg/l concentration range.     

Study on an on-line molecularly imprinted solid-phase extraction coupled to high-performance liquid chromatography for separation and determination of trace estrone in environment

Estrone is one of the important potential endocrine-disrupting compounds, and the sensitive and reliable analytical methods for the determination of estrone are required for the assurance of human health. In this paper, using estrone as template molecule, 3-aminopropyltriethoxysilane as function monomer, and tetraethoxysilicane as cross-linker, a highly selective molecularly imprinted microsphere was synthesized by surface molecular imprinting technique combined with a sol–gel process. The imprinted material was characterized by the Fourier transform infrared and static adsorption experiments, and the results showed that it exhibited good recognition and selective ability for estrone. A novel method for separation and determination of trace estrone in environmental sample was developed using on-line molecularly imprinted solid-phase extraction coupled to high-performance liquid chromatography. With a sample loading flow rate of 2.6 mL min⁻¹ for a 9.6-min extraction, the enrichment factor obtained by the slopes of the linear portion in comparison with the direct injection of 10 μL standard sample solution was 1,045. The detection limit (S/N = 3) was 5.7 ng L⁻¹, and the relative standard deviations for nine replicate extractions of 5.0 μg L⁻¹ estrone was less than 10.0%. This method was evaluated for quantitative determination of estrone in well and lake water samples spiked at two levels (0.5 and 1.0 μg L⁻¹) with recoveries ranging from 86% to 95%.      

Automated Method for the Selective Determination of Gold by On-Line Solvent Extraction and Reversed Micellar-Mediated Luminol Chemiluminescence Detection

A new method based on the direct coupling of on-line solvent extraction with chemiluminescence (CL) of luminol in reverse micelles is proposed for the determination of gold(III) in a reverse-flow injection system. In the on-line process, gold(III) is extracted from aqueous hydrochloric acid solution with tri-n-octylphosphine oxide in chloroform, followed by separation through a microporous Teflon membrane. A reversed micellar system of cetyltrimethylammonium chloride-water (buffered with sodium carbonate)-6:5 (v/v) chloroform-cyclohexane was used as a medium for the CL reaction. Linear calibration for gold was established over the concentration range 10-5000 ng ml⁻¹ and the detection limit was 1 ng ml⁻¹. Much higher tolerable levels of potential interfering metal ions were achieved for the present on-line procedure. The present method was applied to the analysis of industrial samples of silver-based alloy.     

Development of a high‐throughput method based on thin‐film microextraction using a 96‐well plate system with a cork coating for the extraction of emerging contaminants in river water samples

In this study, a new method was developed in which a biosorbent material is used as the extractor phase in conjunction with a recently described sample preparation technique called thin‐film microextraction and a 96‐well plate system. The method was applied for the determination of emerging contaminants, such as 3‐(4‐methylbenzylidene) camphor, ethylparaben, triclocarban, and bisphenol A in water samples. The separation and detection of the analytes were performed by high‐performance liquid chromatography with diode array detection. These contaminants are considered hazardous to human health and other living beings. Thus, the development of an analytical method to determine these compounds is of great interest. The extraction parameters were evaluated using multivariate and univariate optimization techniques. The optimum conditions for the method were 3 h of extraction time, 20 min of desorption with 300 μL of acetonitrile and methanol (50:50, v/v), and the addition of 5% w/v sodium chloride to the sample. The analytical figures of merit showed good results with linear correlation coefficients higher than 0.99, relative recoveries of 72–125%, interday precision (n = 3) of 4–18%, and intraday precision (n = 9) of 1–21%. The limit of detection was 0.3–5.5 μg/L, and the limit of quantification was 0.8–15 μg/L.     

A new method for the synthesis of 2,4-diamino-6-arylpyrimidines

A method for the synthesis of 2,4-diamino-6-arylpyrimidines from guanidine and α-chlorocinnamonitriles was developed. The starting nitriles can be easily prepared by catalytic olefination reaction.__________Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 1, pp. 249–251, January, 2005.     

Determination of total thallium in soils by atomic emission spectrography using a two-jet arc plasmatron

A procedure is proposed for the direct determination of total thallium in solid soil samples by atomic emission spectrography with spectral excitation in an two-jet argon-arc plasmatron. The conditions for spectrum excitation and registration have been optimized. The analytical possibilities of the two zones in the plasma jet, before and after the jet confluence, were compared using the determination of thallium in soils as an example. Reference samples were artificial mixtures prepared on the basis of real soils. The accuracy of the results was estimated using the t-test in the analysis of samples with the known analyte concentrations. The experimentally found detection limit is 0.3–0.5 mg/kg. The relative standard deviation at an insignificant systematic error is 12–15% (n = 20; P = 0.95).Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 2, 2005, pp. 165–170.Original Russian Text Copyright © 2005 by Cherevko, Polyakova.This revised version was published online in April 2005 with corrections to the author names and book review format.     

Ultratrace determination of tin by hydride generation in-atomizer trapping atomic absorption spectrometry

A quartz multiatomizer with its inlet arm modified to serve as a trap (trap-and-atomizer device) was employed to trap tin hydride and subsequently to volatilize collected analyte species with atomic absorption spectrometric detection. Generation, atomization and preconcentration conditions were optimized and analytical figures of merit of both on-line atomization as well as preconcentration modes were quantified. Preconcentration efficiency of 95 ± 5% was found. The detection limits reached were 0.029 and 0.14 ng mL⁻¹ Sn, respectively, for 120 s preconcentration period and on-line atomization mode without any preconcentration. The interference extent of other hydride forming elements (As, Se, Sb and Bi) on tin determination was found negligible in both modes of operation. The applicability of the developed preconcentration method was verified by Sn determination in a certified reference material as well as by analysis of real samples.