Surface-enhanced Raman scattering spectroscopy of explosive 2,4-dinitroanisole using modified silver nanoparticles

2,4-Dinitroanisole (DNAN) is being used as a replacement for 2,4,6-trinitrotoluene (TNT) as a less-sensitive melt-cast medium explosive than TNT. In this paper, we studied the surface-enhanced Raman spectroscopy (SERS) analysis of DNAN using Ag nanoparticles (AgNPs) modified by L-cysteine methyl ester hydrochloride. Due to the formation of a Meisenheimer complex between DNAN and the modifier, the modified AgNPs can detect 20 μg/L (0.2 ng) and 0.1 mg/L (1 ng) DNAN in deionized water and aged tap water, respectively. Three other chemicals (L-cysteine, N-acetyl-L-cysteine, and L-cysteine ethyl ester hydrochloride) were used as AgNPs modifiers to study the mechanism of the SERS of DNAN. It was confirmed that the amino group of L-cysteine methyl ester hydrochloride was the active group and that the methyl ester group significantly contributed to the high SERS sensitivity of DNAN. In order to further test the mechanism of Meisenheimer complex formation, the effect of anions and cations present in natural water on the SERS of DNAN was studied. It was found that CO(3)(2-), Cl(-), and K(+) at 100 mg/L did not negatively affect the SERS of 10 mg/L DNAN, while SO(4)(2-), Na(+), Mg(2+), and Ca(2+) at 100 mg/L significantly quenched the SERS of 10 mg/L DNAN. The negative effect of the bivalent cations could be offset by SO(4)(2-).     

Surface-enhanced Raman scattering for arsenate detection on multilayer silver nanofilms

Surface-enhanced Raman scattering (SERS) has recently emerged as a promising method for chemical and biomolecular sensing. SERS quantification analysis of arsenate (As(V)) was investigated using multilayer Ag nanofilms deposited on glass slides as SERS-active substrates (Ag/GL substrates) by an electroless deposition process. The As(V) limit of detection (LOD) was determined to be ～5 μg L(-1) or lower with or without coexisting multiple background electrolytes (Na(+), K(+), Ca(2+), Mg(2+), Cl(-), NO(3)(-), SO(4)(2-) and H(2)PO(4)(-)). The presence of the background electrolytes at low concentrations was observed to enhance the SERS sensitivity of the substrate towards As(V) more than twofold. Standard calibration curves were prepared in the absence and presence of the background electrolytes. Excellent linear relationships between the peak heights of the As(V) SERS band at ～780 cm(-1) and the As(V) concentrations were obtained in a concentration range of 0-250 μg L(-1). The selectivity of the Ag nanofilm towards oxyanions was examined to be in the order of As(V)?phosphate?nitrate, sulphate. A low sample-to-sample relative standard deviation (RSD) of 5.2% was also determined, suggesting the Ag/GL substrate was uniform and highly reproducible. Experimental results indicated that the SERS method could be used for quantitative analysis of As(V) in groundwater samples.     

Synthesis of magnetic polyphosphazene-Ag composite particles as surface enhanced Raman spectroscopy substrates for the detection of melamine

Magnetic polyphosphazene(MPZS) particles coated by Ag nanoparticles(MPZS-Ag) have been developed as surface enhanced Raman spectroscopy(SERS) substrates for sensitive detection of melamine in aqueous solutions and milk samples.5,5'-Dithiobis-(2-nitrobenzoic acid)(DTNB) was used as model analyte to test the SERS activity of the MPZS-Ag particles.The prepared MPZS-Ag particles possess both magnetic responsiveness and excellent SERS properties.SERS detection of different concentrations of melamine aqueous solutions and spiked milk samples were performed by the MPZS-Ag particles.The limit of detection(LOD) of the melamine in aqueous solutions was 10-7 mol/L(0.0126 mg/L) and 0.6 mg/L in real milk samples using the MPZS-Ag particles as SERS substrates.The LOD of the melamine are much lower than the safety values of Food and Drug Administration and Codex Alimentarius Commission.These results indicate that the MPZS-Ag particles have promising application prospect for SERS analysis in food safety fields.     

Substrates with discretely immobilized silver nanoparticles for ultrasensitive detection of anions in water using surface-enhanced Raman scattering

Positively charged silver nanoparticles, Ag [+], obtained by UV-assisted reduction of silver nitrate using branched poly(ethyleneimine) (BPEI) and 4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid (HEPES) solutions as reducing agents, were immobilized on glass surfaces to produce substrates active in surface-enhanced Raman scattering (SERS). Negatively charged silver nanoparticles, Ag [-], synthesized via a modified citrate reduction method, were also investigated for comparison. At a sparse surface coverage of 30 nanoparticles/microm(2), substrates with immobilized Ag [+] showed increasing SERS sensitivity to a variety of anions in water in the order SO(4)(2-) < CN(-) < SCN(-) approximately ClO(4)(-), with corresponding binding constants of 10(5), 3.3 x 10(5), and 10(7) (for both SCN- and ClO(4)(-)) M(-1), respectively. This order followed the Hofmeister series of anion binding in water. Significantly, substrates with Ag [+] allowed limit of detection values of 8.0 x 10(-8) M (8 ppb) and 2.7 x 10(-7) M (7 ppb) for environmentally relevant perchlorate (ClO(4)(-)) and cyanide (CN(-)) anions, respectively. In contrast, substrates with immobilized Ag [-], even upon subsequent modification by a monolayer of BPEI for positive surface charge of the nanoparticles, showed a drastically lower sensitivity to these anions. The high sensitivity of substrates with Ag [+] for anion detection can be attributed to the presence of two types of functional groups, amino and amide, on the nanoparticle surface resulting from UV-assisted fragmentation of BPEI chains. Both amino and amide provide strong binding of anions with Ag [+] nanoparticles due to the synergistic effect through a combination of electrostatic, hydrogen bonding, and dispersive interactions.     

Ultrasensitive SERS Detection of TNT by Imprinting Molecular Recognition Using a New Type of Stable Substrate

We report herein a method for the ultra‐trace detection of TNT on p‐aminothiophenol‐functionalized silver nanoparticles coated on silver molybdate nanowires based on surface‐enhanced Raman scattering (SERS). The method relies on π‐donor–acceptor interactions between the π‐acceptor TNT and the π‐donor p,p′‐dimercaptoazobenzene (DMAB), with the latter serving to cross‐link the silver nanoparticles deposited on the silver molybdate nanowires. This system presents optimal imprint molecule contours, with the DMAB forming imprint molecule sites that constitute SERS “hot spots”. Anchoring of the TNT analyte at these sites leads to a pronounced intensification of its Raman emission. We demonstrate that TNT concentrations as low as 10^?12 M can be accurately detected using the described SERS assay. Most impressively, acting as a new type of SERS substrate, the silver/silver molybdate nanowires complex can yield new silver nanoparticles during the detection process, which makes the Raman signals very stable. A detailed mechanism for the observed SERS intensity change is discussed. Our experiments show that TNT can be detected quickly and accurately with ultra‐high sensitivity, selectivity, reusability, and stability. The results reported herein may not only lead to many applications in SERS techniques, but might also form the basis of a new concept for a molecular imprinting strategy.     

The ultratrace detection of crystal violet using surface enhanced Raman scattering on colloidal Ag nanoparticles prepared by electrolysis

Highly active,stable and affordable surface enhanced Raman scattering(SERS) substrates were obtained by electrolyzing a mixture of AgNO_3(4×10~(-4) mol/L) and Na_3C_6H_5O_7·H_2O(6×10~(-5) mol/L) for 1,2,3 and 4h at 7V.With crystal violet(CV) as a test molecule,a portable Raman spectrometer with 785 nm laser excitation was employed to carry out the SERS detection.Colloidal Ag nanoparticles prepared by electrolyzing for 3 h with the particle size of(65±17) nm is a perfect SERS substrate for the ultratrace ...     

Selective detection of aqueous nitrite ions by surface-enhanced Raman scattering of 4-aminobenzenethiol on Au

In this work, we have devised a selective nitrite-ion detection method based on the surface-enhanced Raman scattering (SERS) of 4-aminobenzenethiol (4-ABT) on Au. This is possible because, firstly, SERS is a very surface-sensitive technique with monolayer detection capability, and secondly, the amine group of 4-ABT reacts readily with nitrites in acidic media, forming a diazonium group, which can subsequently form an azo bond by reacting with a variety of benzene derivatives. From the peak intensity of the diazonium group, the presence of nitrite ions above 20 μM can be identified readily. From the peak intensity of the azo moiety alone, it is even possible to detect nitrite ions at concentrations as low as 5 μM, without interference from other anions. This work clearly illustrates the usefulness of SERS in environmental science research.     

Evaluation of the potential of surface enhancement Raman spectroscopy for detection of tricyclic psychotropic drugs. Case studies on imipramine and its metabolite

The potential use of surface Raman enhanced spectroscopy (SERS) for confirmatory identification and the semi-quantitative analysis of selected tricyclic antidepressants (TCAs) is examined utilizing a conventional silver colloid. Raman and SERS spectra of aqueous solutions of imipramine (Imi) and its metabolite, desipramine (Des), were recorded as the function of concentration using NIR excitation. A good linear correlation is observed for the dependence of the SERS signal at 684 cm(-1) (R(2) = 0.9997) on Imi concentration over the range of 0.75-7.5 μM. The limit of detection of imipramine in the silver colloidal solution is 0.98 μM. SERS spectra of Imi and Des were also recorded for blood plasma samples without prior purification as well as after the use of standard solid phase extraction. All spectra show the characteristic spectral profile of the molecules and moreover, stronger signal enhancement is observed for Imi in the "raw" samples as opposed to Imi extracted from a biological matrix.     

The surface-enhanced Raman spectra of aflatoxins: spectral analysis, density functional theory calculation, detection and differentiation

High-quality surface-enhanced Raman scattering (SERS) spectra of aflatoxin (AF) B(1), B(2), G(1) and G(2) have been acquired using silver nanorod (AgNR) array substrates fabricated by oblique angle deposition method. Significant vibrational peaks are identified on the argon plasma-cleaned substrates, and those peaks agree very well with the Raman spectra calculated by density function theory (DFT). The concentration-dependent SERS detection is also explored. The relationship between the concentration (C) of different AFs and the SERS intensity (I) of the Raman peak at Δν = 1592 cm(-1) is found to follow the general relationship I = AC(α), with α ranging from 0.32 to 0.46 for the four AFs. The limits of detection (LODs) reach 5 × 10(-5) mol L(-1) for AFB(1), 1 × 10(-4) mol L(-1) for AFB(2), and 5 × 10(-6) mol L(-1) for both AFG(1) and AFG(2) in bulk solution, or 6.17 × 10(-16) mol/1.93 × 10(-4) ng of AFB(1), 1.23 × 10(-15) mol/3.88 × 10(-4) ng for AFB(2), 6.17 × 10(-17) mol/2.03 × 10(-5) ng for AFG(1), and 6.17 × 10(-17) mol/2.04 × 10(-5) ng for AFG(2) per laser spot. Principal component analysis (PCA) is used to successfully differentiate these four different kinds of AFs at different concentrations up to their detection limits. The LODs obtained from PCA agree with the LODs obtained by using peak fitting method. With such a low detection limit and outstanding differentiation ability, we prove the possibility of utilizing the SERS detection system as a platform for highly sensitive mycotoxin detection.     

Cetylpyridinium Chloride Activated Trinitrotoluene Explosive Lights Up Robust and Ultrahigh Surface‐Enhanced Resonance Raman Scattering in a Silver Sol

Surface‐enhanced resonance Raman scattering (SERRS) is not realized for most molecules of interest. Here, we developed a new SERRS platform for the fast and sensitive detection of 2,4,6‐trinitrotoluene (TNT), a molecule with low Raman cross section. A cationic surfactant, cetylpyridinium chloride (CPC) was modified on the surface of silver sols (CP‐capped Ag). CPC not only acts as the surface‐seeking species to trap sulfite‐sulfonated TNT, but also undergoes complexation with it, resulting in the presence of two charge‐transfer bands at 467 and 530 nm, respectively. This chromophore absorbs the visible light that matches with the incident laser and plasmon resonance of Ag sols by the use of a 532.06 nm laser, and offered large resonance Raman enhancement. This SERRS platform evidenced a fast and accurate detection of TNT with a detection limit of 5×10^?11 M under a low laser power (200 μW) and a short integration time (3 s). The CP‐capped Ag also provides remarkable sensitivity and reliable repeatability. This study provides a facile and reliable method for TNT detection and a viable idea for the SERS detection of various non‐resonant molecules.     

A ratiometric fluorescent chemosensor for iron: discrimination of Fe2+ and Fe3+ and living cell application

A newly designed probe, 6-thiophen-2-yl-5,6-dihydrobenzo[4,5]imidazo-[1,2-c] quinazoline (HL(1)) behaves as a highly selective ratiometric fluorescent sensor for Fe(2+) at pH 4.0-5.0 and Fe(3+) at pH 6.5-8.0 in acetonitrile-HEPES buffer (1/4) (v/v) medium. A decrease in fluorescence at 412 nm and increase in fluorescence at 472 nm with an isoemissive point at 436 nm with the addition of Fe(2+) salt solution is due to the formation of mononuclear Fe(2+) complex [Fe(II)(HL)(ClO(4))(2)(CH(3)CN)(2)] (1) in acetonitrile-HEPES buffer (100 mM, 1/4, v/v) at pH 4.5 and a decrease in fluorescence at 412 nm and increase in fluorescence at 482 nm with an isoemissive point at 445 nm during titration by Fe(3+) salt due to the formation of binary Fe(3+) complex, [Fe(III)(L)(2)(ClO(4))(H(2)O)] (2) with co-solvent at biological pH 7.4 have been established. Binding constants (K(a)) in the solution state were calculated to be 3.88 × 10(5) M(-1) for Fe(2+) and 0.21 × 10(3) M(-1/2) for Fe(3+) and ratiometric detection limits for Fe(2+) and Fe(3+) were found to be 2.0 μM and 3.5 μM, respectively. The probe is a "naked eye" chemosensor for two states of iron. Theoretical calculations were studied to establish the configurations of probe-iron complexes. The sensor is efficient for detecting Fe(3+)in vitro by developing a good image of the biological organelles.     

An effective metallohydrolase model with a supramolecular environment: structures, properties, and activities

A supramolecular inclusion complex, [Zn(L1)(H2O)2(beta-CD)](ClO4)2.9.5 H2O (1) was synthesized and characterized structurally and its first-order active species for hydrolysis of esters, [Zn(L1)(H2O)(OH)(beta-CD)](ClO4) (2), was isolated (L1=4-(4'-tert-butylbenzyl)diethylenetriamine; beta-CD=beta-cyclodextrin). The apparent inclusion stability constant of the host and the guest measured in aqueous solution was (5.91+/-0.03)x10(3) for 1. The measured values of the first- and second-order pK(a) values of coordinated water molecules were 8.20+/-0.08 and 10.44+/-0.08, respectively, and were assigned to water molecules occupying the plane and remaining axial positions in a distorted trigonal bipyramid of the [Zn(L1)(H2O)2(beta-CD)]2+ sphere according to the structural analysis of [Zn(L2)(H2O)}2(mu-OH)](ClO4)3 (3) (L2=4-benzyldiethylenetriamine). p-Nitrophenyl acetate (pNA) hydrolysis catalyzed by 1 at pH 7.5-9.1 and 25.0+/-0.1 degrees C exhibited a first-order reaction with various concentrations of pNA and 1, but the pH profile did not indicate saturated kinetic behavior. Second-order rate constants of 0.59 and 24.0 M(-1) s(-1) were calculated for [Zn(L1)(H2O)(OH)(beta-CD)]+ and [Zn(L1)(OH)2(beta-CD)], respectively; the latter exhibited a potent catalytic activity relative to the reported mononuclear and polynuclear Zn(II) species.     

Ferrocene-conjugated L-tryptophan copper(II) complexes of phenanthroline bases showing DNA photocleavage activity and cytotoxicity

Ferrocene-conjugated L-tryptophan (L-Trp) reduced Schiff base (Fc-TrpH) copper(II) complexes [Cu(Fc-Trp)(L)](ClO(4)) of phenanthroline bases (L), viz. 2,2'-bipyridine (bpy in 1), 1,10-phenanthroline (phen in 2), dipyrido[3,2-d:2',3'-f]quinoxaline (dpq in 3), and dipyrido[3,2-a:2',3'-c]phenazine (dppz in 4), were prepared and characterized and their photocytotoxicity studied. Cationic reduced Schiff base (Ph-TrpH) complexes [Cu(Ph-Trp)(L)(H(2)O)](ClO(4)) (L = phen in 5; dppz in 6) having the ferrocenyl moiety replaced by a phenyl group and the Zn(II) analogue (7) of complex 4 were prepared and used as control species. The crystal structures of 1 and 5 with respective square-planar CuN(3)O and square-pyramidal CuN(3)O(2) coordination geometry show significantly different core structures. Complexes 1-4 exhibit a Cu(II)-Cu(I) redox couple near -0.1 V and the Fc(+)-Fc couple at ~0.5 V vs SCE in DMF-0.1 M [Bu(n)(4)N](ClO(4)) (Fc = ferrocenyl moiety). The complexes display a copper(II)-based d-d band near 600 nm and a Fc-centered band at ~450 nm in DMF-Tris-HCl buffer. The complexes are efficient binders to calf thymus DNA. They are synthetic chemical nucleases in the presence of thiol or H(2)O(2), forming hydroxyl radicals. The photoactive complexes are cleavers of pUC19 DNA in visible light, forming hydroxyl radicals. Complexes 2-6 show photocytotoxicity in HeLa cancer cells, giving IC(50) values of 4.7, 10.2, 1.3, 4.8, and 4.3 μM, respectively, in visible light with the appearance of apoptotic bodies. The complexes also show photocytotoxicity in MCF-7 cancer cells. Nuclear chromatin cleavage has been observed with acridine orange/ethidium bromide (AO/EB) dual staining with complex 4 in visible light. The complexes induce caspase-independent apoptosis in the HeLa cells.     

The use of chlorophenol red for the selective determination of chlorine dioxide in drinking water

In recent years, the use of chlorine dioxide as an alternative disinfectant for drinking water has become increasingly attractive. As a result, an accurate method for the determination of mg l(-1) concentrations of chlorine dioxide is needed. Improvements to chlorophenol red (CPR) spectrophotometry result in a selective method for ClO(2) with few interferences. CPR selectively reacts with 0.1-1.9 mg l(-1) ClO(2) at pH 7, yielding a linear response (0.9994) with a limit of detection of 0.12 mg l(-1) ClO(2). Several species, ClO(2)(-), ClO(3)(-), NH(2)Cl, and free available chlorine (FAC), were studied as potential interferents using this method. There was found to be less than 2% interference due to 1.38 mg l(-1) ClO(2)(-), 9.87 mg l(-1) ClO(3)(-1), and 5.31 mg l(-1) NH(2)Cl. The interference from up to 1.19 mg l(-1) FAC was 3.7% and could be further reduced by the addition of oxalic acid, sodium cyclamate or thioacetamide.     

Silver nanoparticle aggregates on copper foil for reliable quantitative SERS analysis of polycyclic aromatic hydrocarbons with a portable Raman spectrometer

Silver nanoparticle aggregates were synthesized on copper foil, which was used for the surface-enhanced Raman spectroscopy (SERS) detection of polycyclic aromatic hydrocarbons (PAHs) with a portable Raman spectrometer. Silver nanoparticle aggregates were prepared by immersing copper foil in the solution of Sn(2+) and AgNO(3) in a cyclic fashion. A four-cycle process was selected for the following experiments due to its high enhancement and relatively convenient experimental procedure. The substrate has greater temporal stability under continuous laser radiation, good uniformity and reproducibility, which indicated that the substrate could provide reliable measurements. The relationship between SERS intensity and concentrations of PAHs was studied. Quantitative analysis of PAHs in aqueous solution was further performed based on the prepared substrate. The log-log plot of normalized SERS intensity to PAHs concentration exhibited a good linear relationship, with the detection limits in the range of 5-500 μg L(-1). Thus, due to the stability, reproducibility and quantitative results, the prepared substrate could be used as a potential SERS sensor for the analysis of environmental pollutants.     

Detection of melamine in milk by surface-enhanced Raman spectroscopy coupled with magnetic and Raman-labeled nanoparticles

A new method based on surface-enhanced Raman spectroscopy (SERS) has been developed for sensitive and rapid detection of melamine. Spherical magnetic-core gold-shell nanoparticles (AuNPs) and rod-shaped gold nanoparticles (nanorods) labeled with a Raman-active compound were used to form a complex with the melamine molecules. 5,5'-Dithiobis(2-nitrobenzoic acid) was used as Raman-active compound because it is readily adsorbed by a gold nanoparticle surface forming a self-assembled monolayer (SAM) and has strong Raman scattering at 1330 cm(-1), because of the symmetric NO(2) stretch. The calibration curve was obtained by plotting Raman band area at 1330 cm(-1) against melamine concentration. A linear relationship was obtained with a high determination coefficient (R(2)=0.997). The method was validated for linearity, sensitivity, precision (intra-day and inter-day repeatability), and recovery. In the model system, the limits of detection (LOD) and quantification (LOQ) were 0.38 and 1.27 mg L(-1), respectively. For melamine-spiked milk samples, LOD and LOQ values were 0.39 mg L(-1) and 1.30 mg L(-1), respectively. Intra and inter-day precision were 3.73 and 4.94 %, respectively. This method was applied to samples of skimmed milk that had been spiked with melamine at different concentrations. The recovery of the method was 95-109 % in the concentration range 2-15 mg L(-1), and average RSD was 1.71 %. Total analysis time was less than 15 min.     

应用表面增强拉曼光谱技术快速检测尿样中的β-兴奋剂

应用表面增强拉曼光谱技术与化学计量法相结合分析克伦特罗、沙丁胺醇和莱克多巴胺3种β-兴奋剂的标准溶液.在取自10头猪的尿样中,分别添加5个不同浓度的莱克多巴胺(1～20 mg/L),采用快速的液液萃取法对样品进行前处理,再进行表面增强拉曼测试.结果表明,克伦特罗和沙丁胺醇标准溶液的最低检测浓度为2 μg/L,莱克多巴胺标准溶液的最低检测浓度为0.1 mg/L;通过偏最小二乘法建立模型进行定量分析,3种药物的实际值与预测值的相关系数(R2)为0.9134～0.9368;本方法可检测尿样中1 mg/L莱克多巴胺,经外部验证后模型的实际值与预测值的相关系数(R2)为0 881,相对分析误差(RPD)为2.83;分析尿液中的莱克多巴胺含量所需时间小于30 min,为快速检测莱克多巴胺提供新途径.     

Hofmeister effects in micromolar electrolyte solutions

Ions induce both specific (Hofmeister) and non-specific (Coulomb) effects at aqueous interfaces. More than a century after their discovery, the origin of specific ion effects (SIE) still eludes explanation because the causal electrostatic and non-electrostatic interactions are neither local nor separable. Since direct Coulomb effects essentially vanish below ~10 μM (i.e., at >50 nm average ion separations in water), we decided to investigate whether SIE operate at, hitherto unexplored, lower concentrations. Herein, we report the detection of SIE above ~0.1 μM in experiments where relative iodide∕bromide populations, χ = I(-)/Br(-), were determined on the surface of aqueous (NaI + NaBr) jets by online electrospray mass spectrometry in the presence of variable XCl (X = H, Na, K, Cs, NH(4), and N(C(4)H(9))(4)) and NaY (Y = OH, Cl, NO(3), and ClO(4)) concentrations. We found that (1) all tested electrolytes begin to affect χ below ~1 μM and (2) I(-) and Br(-) are preferentially suppressed by co-ions closely matching their interfacial affinities. We infer that these phenomena, by falling outside the reach of even the longest ranged electrostatic interactions, are dynamical in nature.     

Selective colorimetric and fluorometric sensing of Cu(II) by iminocoumarin derivative in aqueous buffer

A new iminocoumarin based receptor L (C(27)H(26)N(4)OS) is synthesized with pyridyl and benzothiazolyl functionality. Synthesis of L is easy and it is isolated in good yield. L shows a selective and distinct color change from yellow to orange with Cu(2+) over Li(+), Na(+), Ca(2+), Mg(2+), Cr(2+), Mn(2+), Fe(2+), Co(2+), Ni(2+), Cu(2+), Zn(2+), Cd(2+), Pb(2+), and Ag(+) whereas a slight change in color is also observed in the case of Hg(2+) but L shows selective fluorescent quenching only in the presence of Cu(2+) in aqueous HEPES buffer (pH 7.0). The naked eye detection limit of Cu(2+) is determined at 2 μM whereas an emission experiment shows a lower detection limit at 200 nM. Selectivity studies of L in presence of 50 equivalents of other ion(s) by emission experiment show no interference toward the detection of 1 equivalent of Cu(2+). Both UV-Vis and fluorescence studies in the presence of Cu(2+)-salts of different counter anions with various sizes and shapes (Cl(-), ClO(4)(-), NO(3)(-), CF(3)SO(3)(-), SO(4)(2-) and BF(4)(-)) show almost similar spectral output in buffer media irrespective of the nature of the counter anions. The detailed UV-Vis and fluorescence titration experiments suggest the existence of both 1:1 and 2:1 (L:Cu(2+)) complexation stoichiometry and EPR study shows d(x(2)-y(2)) ground state of the Cu(II) centre in the complex. Furthermore the formation of a mononuclear [Cu(L)(CH(3)CN)].2ClO(4) complex and the flexible conformation of L in the solid state are confirmed by the single-crystal X-ray structural study.     

On-chip ultra-thin layer chromatography and surface enhanced Raman spectroscopy

We demonstrate that silver nanorod (AgNR) array substrates can be used for on-chip separation and detection of chemical mixtures by combining ultra-thin layer chromatography (UTLC) and surface enhanced Raman spectroscopy (SERS). The UTLC-SERS plate consists of an AgNR array fabricated by oblique angle deposition. The capability of the AgNR substrates to separate the different compounds in a mixture was explored using a mixture of four dyes and a mixture of melamine and Rhodamine 6G at varied concentrations with different mobile phase solvents. After UTLC separation, spatially-resolved SERS spectra were collected along the mobile phase development direction and the intensities of specific SERS peaks from each component were used to generate chromatograms. The AgNR substrates demonstrate the potential for separating the test dyes with plate heights as low as 9.6 μm. The limits of detection are between 10(-5)-10(-6) M. Furthermore, we show that the coupling of UTLC with SERS improves the SERS detection specificity, as small amounts of target analytes can be separated from the interfering background components.