Effect of the composition and concentration of fibrous wastes from linen yarn production on the physicomechanical properties of polyolefin composites

An analysis is made of the feasibility of using wastes from the production of linen yarm (scutch, spinning and carding refuse) to modify low-density polyethylene. The effect of the composition and concentration of wastes on the processing properties (melt index), physicomechanical indices (tensile strength, elastic modulus in bending), and water resistance of composites based on low-density polyethylene is studied. It is found that the melt index decreases with an increase in the content of filler and that even a composite with a high filler content (40–50% by weight) maintains values of 0.2–0.3 g/10 min. The elastic modulus in bending increases with an increase in the content of waste, regardless of the nature of the latter. Tensile strength increases slightly and depends on the choice of filler. This result, combined with the reducation in the scatter of values of elastic modulus with an increase in filler concentration, is an indicator of the relatively high degree of heterogeneity of the systems that were studied. The water resistance of the composites decreases with an increase in filleer content. To reduce the heterogeneity of the systems, mixing should be intensified and modifiers such as stearic acid and polyisocyanates should be added.Translated from Mekhanika Kompozitnykh Materialov, Vol. 33, No. 3, pp. 408–416, May–June, 1997.     

Comparative micromechanical analysis of nonelastic behavior of unidirectional plastics with tetragonal and hexagonal structures

A mathematical model for determining the effective elastic properties and describing the processes of inelastic deformation and damage accumulation of unidirectional fiber-reinforced composites with tetragonal and hexagonal structures is developed. A comparative analysis of the effective elastic moduli of glass, boron, organic, and carbon unidirectional plastics shows that, if the fiber volume fraction does not exceed 0.5, the effective elastic properties calculated by the models presented give closely related results. The calculation results for nonlinear fields of deformation and failure are presented and the limiting strength surfaces of fibrous glass plastics with hexagonal and tetragonal structures are obtained for different transverse loading paths. It is found that the structure of a composite affects significantly its strength properties.Submitted to the 11th International Conference on Mechanics of Composite Materials (Riga, June 11–15, 2000).Perm' State Technical University, Perm', Russia. Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 4, pp. 455–464, July–August, 2000.     

Effect of fillers on the structure and properties of cured resins

The elastic (modulus of elasticity and equilibrium high-elastic modulus) and thermal (volume coefficients of thermal expansion below and above the glass transition temperature) properties of compositions based on ÉD-5 epoxy resin cured with polyethylenepolyamine have been investigated. Quartz powder and aluminoborosilicate glass powder were employed as fillers at concentrations from 0 to 0.413. The thermal expansion coefficients of the compositions were studied in a dilatometer, in which the specimen is free of mechanical loads. The Young's modulus at 25°C and the equilibrium high-elastic modulus at 125°C of the compositions were determined in the compression regime in an instrument based on the IZV-2 optical length gage. The thermal expansion coefficients of the polymer matrix were calculated with allowance for the elastic properties of the resin and the filler. It is shown that, as the filler concentration increases, the thermal and elastic properties of the resin in the filled system change. This can be interpreted as a change in the properties of the resin as it approaches the surface of the filler particles. Increased interaction between the filler surface and the epoxy resin tends to stiffen the polymer network.Scientific Research Institute of Precision Technology, Moscow. Translated from Mekhanika Polimerov, No. 6, pp. 1018–1022, November–December, 1969.     

Minimizing the mass of cylindrical shells formed from a composite material with an elastic filler and designed for strength and stability under a combined loading

The mass of a multilayer cylindrical shell, formed from a composite material with an elastic filler and designed for strength and stability under the combined action of axial compression and external pressure, is minimized. The problem is formulated as one of nonlinear programming and is solved by Rossen's method of projection gradients. The strength of the material is established from analysis of the strength of the layers making up the entire bundle. Failure of an individual layer is determined from Malmeister's criterion. The structure of a shell with different external loads and the dependence of minimal mass on the stiffness of the filler and on the volume coefficient of reinforcement are investigated in numerous examples.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. K. Preikshas Shyaulyaisk Pedagogical Institute. Translated from Mekhanika Polimerov, No. 2, pp. 289–297, March–April, 1976.     

Optimal designing of orthotropic cylindrical shells fastened to elastic filler

Conclusions A method has been proposed for optimally designing an orthotropic cylindrical shell rigidly fastened to an elastic and isotropic filler of finite dimensions. The design takes into account simultaneous action of pressure, body forces, and heat on the structure. The optimum design has been calculated for the case of temperature-dependent elastic properties and strength characteristics of the tape. The method allows also for limitation on the strength of the filler. The convergence of the iteration process schematically shown in Fig. 2 is quite fast. Indeed, for the given design variant, the condition of manufacturability (1) is satisfied with a sixfold margin in the third approximation (n=3) already.Translated from Mekhanika Kompozitnykh Materialov, No. 1, pp. 91–94, January–February, 1984.     

Study of the effect of the dressing of carbon fibers on the properties of carbon-fiber-reinforced plastics based on polyacetals

Studies are made of the mechanical and friction engineering properties of a copolymer of trioxane-1,3,5 with dioxolan-1,3 reinforced with dressed carbon fibers based on hydrated cellulose. Polyalkyloxysilanes are used as the finishes. The optimum concentrations of the finishes on the fibrous filler are determined. Relations are obtained to describe the dependence of the mechanical properties of carbon-fiber-reinforced plastics on the type of finish and its effect on the condition of the phase boundary between filler and the polymer matrix. The effect of adhesion of the polymer to the fibrous filler on the properties of a randomly reinforced thermoplastic composite is also determined. The dependences of the friction engineering properties of polyacetal-based carbon-plastics on the loading parameters of the friction-loading unit are examined. The material that is developed has high values of strength, elastic modulus, and notch toughness and low values of the friction coefficient and shrinkage. The material can be used as structural and anti-friction elements in rocketry, aviation, and the automobile industry.Ukrainian State Chemical Engineering University, Dnepropetrovsk. Translated from Mekhanika Kompozitnykh Materialov, No. 1, pp. 90–97, January–February, 1997.     

Effect of aggregation of a dispersed rigid filler on the elastic characteristics of a polymer composite

Conclusions We proposed a method for describing the effective elastic characteristics of a polymer composite with a rigid aggregating filler. An important feature of such a medium is the variable coupling of the inclusion phase in relation to its volume content. A change in the degree of coupling of the filler is accounted for by introducing an additional parameter. We examined a method of determining the coupling parameter from the results of statistical modeling of the geometry of the medium. Using the example of a calcite-HDPE composite, we showed that aggregation has a significant effect on the dependence of the elastic modulus on the volume content of filler; satisfactory agreement was obtained between the theoretical and experimental data.Translated from Mekhanika Kompozitnykh Materialov, No. 1, pp. 14–22, January–February, 1986.     

Effect of small additives of oligomer on the viscoelastic properties of carbon fiber plastics

The viscoelastic properties of carbon fiber composites whose phenol-formaldehyde matrix is modified by thermodynamically incompatible isocyanate derivatives have been investigated. Data are given on fiber wetting (Table 11), internal stress (Table 2), viscoelastic properties (Fig. 1), and tensile strength (Fig. 2). The modified composites are strengthened by the addition of 0.5–4% oligomer additive. This process involves the formation of a two-phase structure, in which the additive phase microparticles act as a polymer filler. Due to selective interactions, the intermediate layer formed at the fiber-binder interface leads to changes in the viscoelastic properties and tensile strength of the matrix and improved maintenance characteristics for the material as a whole.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 4, pp. 440–445, July–August, 1993.     

Effect of water sorption on some mechanical parameters of composite systems based on low-density polyethylene and microcrystalline cellulose

Strength-deformation characteristics of low-density polyethylene filled with microcrystalline cellulose Thermocell as a function of the TC content (up to 0.7 parts by weight) are studied. Characteristics such as elastic modulus, relative elongation at break, ultimate strength, and work of failure are determined. Water sorption and change in the size and strength-deformation characteristics of composite specimens during exposure to boiling water (560 min) are also studied. It is shown that with greater filler content it is possible to increase the strength-deformation characteristics of LDPE, such as elastic modulus and tensile strength. The growth of the ultimate strength is associated with the formation of a specific filler framework with increasing filler content. It is found that the main factors which cause a decrease in the elastic modulus and softening of the composite are failure of the filler framework as well as formation of stresses and voids during water sorption by the composite. It is demonstrated that the steady reproducibility of the composition, attainable high filling degrees, and ecological safety make Thermocell a promising filler for polyethylene.Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 1, pp. 79–90, January–February, 1999.     

Production and characterization of UHMWPE fibers/LDPE composites

The production of unidirectionally fiber-reinforced composites (tapes) consisting of high-strength/high-modulus UHMWPE fibers and LDPE matrix is described. Two production techniques are applied: impregnation by aqueous powder dispersion and dry powder impregnation. The produced composites exhibit excellent mechanical properties. Depending on the fiber volume content which can be obtained: tensile strength (in fiber direction) 460–1100 MPa, elastic modulus 11–22 GPa, and elongation at break 4.9–8.3%.Presented at the Ninth International Conference on the Mechanics of Composite Materials, Riga, October, 1995.Technical University of Berlin. Institute of Nonmetallic Materials. Polymer Physics Group.-Englishe Str. 20, D-10587 Berlin. Germany. Published in Mekhanik Kompozitnykh Materialov, Vol. 32, No. 6. pp. 719–728, November–December, 1996.     

Certain properties of filled partly plasticized polyvinylchloride

The effect of iron oxide as a filler for hard partly plasticized polyvinylchloride was studied. It was shown that the influence of iron oxide on polymer properties varies depending on the proportion of the filler used. When added in small quantities, it improves certain physico-mechanical properties of polyvinylchloride, such as, for instance, its hardness and wear resistance.Mekhanika Polimerov, Vol. 2, No. 6, pp. 813–816, 1966     

Fracture in Ceramic-Matrix Composites Reinforced with Strongly Bonded Metal Particles

The resistance of a ceramic matrix composite to the cleavage cracking across a field of strongly bonded, uniformly distributed metal particles is studied. The crack trapping and bridging effects of the metal particles are analyzed by means of calculating the strain energy and the traction work. An explicit expression for the critical energy release rate as a function of particle volume fraction has been obtained. The fracture resistance is independent of elastic properties of the matrix and the sample geometry and is predominantly determined by the size/spacing ratio of the particles. It is shown that the theoretical curves agree with experimental data quite well. The methodology developed in this article can be used in studying the fracture resistances of composites with high filler contents and irregular filler geometries.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 303–318, May–June, 2005.     

Strength of boron fibers

The tensile and flexural strength and elastic properties of continuous boron fibers 95–105 µ in diameter obtained by depositing boron on a tungsten filament 10–12 µ in diameter have been investigated. The strength properties are primarily determined by the defects present at the boron sheath-core interface and for the fibers investigated have a limit of approximately 400 kgf/mm². Coarse surface or internal defects are capable of reducing the strength of the fibers to 200–250 kfg/mm².All-Union Scientific-Research Institute of Aviation Materials, Moscow. Translated from Mekhanika Polimerov, No. 6, pp. 1126–1127, November–December, 1970.     

Effect of a filler on the strength properties of thermosets

The effect of a filler on the strength properties of polymers in tension is investigated. The thermostructural stresses that develop in the composite during cure are taken into account. Relations are given for the strength of the filled polymer as a function of the percentage filler content. In the process of analyzing the thermostructural stresses an analytic expression is obtained for the linear expansion coefficient of the composite with allowance for the structural distribution of the components. Calculated values of the strength and thermostructural stresses are presented for composites with different filler contents. The theoretical determination of the strength of filled polymers is compared with the results of experimental investigations of composites based on epoxy resin filled with quartz dust.Leningrad Mechanical Institute. Translated from Mekhanika Polimerov, No. 1, pp. 97–101, January–February, 1973.     

Elastic and Sorption Characteristics of an Epoxy Binder in a Composite During Its Moistening

Results of an experimental investigation into the elastic and sorption characteristics of a model composite material (CM) — epoxy resin filled with LiF crystals — during its moistening are presented. Properties of the binder in the CM with different filler contents (v _f = 0, 0.05, 0.11, 0.23, 0.28, 0.33, 0.38, and 0.46) were evaluated indirectly by using known micromechanical models of CMs. It was revealed that, for the CM in a conditionally initial state, the elastic modulus of the binder in it and the filler microstrain (change in the interplanar distance in the crystals, measured by the X-ray method) as functions of filler content had the same character. The elastic modulus of the binder in the CM with a low filler content was equal to that for the binder in a block; the elastic modulus of the binder in the CM decreased with increasing filler content. The maximum (corresponding to water saturation of the CM) stresses in the binder and the filler microstresses as functions of filler content were of the same character. Moreover, the absolute values of maximum stresses in the binder and of filler microstresses coincided for high and low contents of the filler. At v _f = 0.2–0. 3, the filler microstrains exceeded the stresses in the binder. The effect of moisture on the epoxy binder in the CM with a high filler content was not entirely reversible: the elastic characteristics of the binder increased, the diffusivity decreased, and the ultimate water content increased after a moistening-drying cycle.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 499–511, July–August, 2005.     

Physicomechanical properties of composites from recycled polyethylene and linen yarn production wastes

The possibilities of utilizing wastes of linen thread production (chaffs, spinning and roving losses) in recycled polyolefin composites have been investigated. The wastes were mixed with recycled polyethylenes (produced from domestic and industrial film production wastes). The physicomechanical properties (tensile strength, bending and tensile moduli, and water resistance) and the fluidity (melt flow-behavior index) for systems with a different filler content are estimated. Almost all the composite materials obtained have satisfactory fluidity (melt flow-behavior index is not lower than 0.07–0.15 dg/min). For all types of the composites, a slight increase in tensile strength and a considerable increase (3–7 times) in bending and tensile moduli were observed. The water resistance of the composites decreased with an increase in the filler content. The modification of filled systems with diisocyanates (diphenylmethane diisocyanate) improved the useful properties and water resistance of all the composites investigated.Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 2, pp. 199–210, March–April, 1999.     

Effect of mineral fillers on properties of composite matrix material

The influence of mineral fillers on thermomechanical properties of matrix material of composites is investigated. Different methods to determine elastic properties and thermal expansion coefficients of composite materials have been considered and compared. Injection moulded polyester samples containing varying concentrations of talc filler are tested and properties such as Young 's modulus, thermal expansion coefficients, and volumetric shrinkage during cure are measured. Results obtained by theoretical models and from experiments are compared and discussed.To be presented at the Ninth International Conference on the Mechanics of Composite Materials (Riga, October 1995).Published in Mekhanika Kompozitnykh Materialov, Vol. 31, No. 4, pp. 435–445, July–August, 1995.     

Pressure pulse from a laser pulse acting on a composite

Conclusions These tests on quasistationary irradiated for polyethylene-matrix powder-filled composites show that the filler composition and content have marked effects on the damage.There are ranges where the specific loss, the pressure, and the integral recoil pulse decrease as the power density increases because of changes in the damage mechanism, which are most prominent for zirconium oxide as filler. Bulk absorption contributes considerably, and causes various types of defect. Estimates have been made of the pressures arising in explosive matrix decomposition in the bulk together with the specific damage energies.These measurements are useful in modeling laser effects on composites.Translated from Mekhanika Kompositnykh Materialov, No. 5, pp. 868–872, September–October, 1988.     

Effect of hydrostatic pressure on mechanical properties of plastics

The effect of hydrostatic pressure on the elastic and strength properties of plastics is investigated. Hydrostatic pressure is found to raise the modulus of elasticity, the tensile strength, and the elastic limit. Approximate equations for calculating the strength and elastic properties under various amounts of hydrostatic presure are proposed.Mekhanika polimerov, Vol. 1, No. 1, pp. 65–75, 1965     

Experimental study on thin three-layer rings with a pliable filler

The bearing capacity of thin three-layer rings containing a pliable filler and exposed to internal and external stresses has been studied experimentally. The deformation and strength properties of the filler have been examined. The initial stresses in the rings examined have been determined by application of three methods; their effect on the bearing capacity has been estimated.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, No. 6, pp. 1032–1037, November–December, 1974.