Kinetics of nonisothermal crystallization of Cs2O–Fe2O3–P2O5 glasses

The crystallization kinetics of Cs₂O–Fe₂O₃–P₂O₅ glasses containing 12.5–27 mol% Cs₂O were studied by using differential scanning calorimetry under nonisothermal conditions. Strong dependence of activation energy with temperature was observed, indicating the complex nature of the crystallization process. The various crystallization products were identified by X-ray diffraction technique. CsFeP₂O₇ was found to be the major crystalline phase in all cases. The overall activation energy obtained by classical model-free kinetic method was compared with that of isoconversional method; and from the results, the dependence of activation energy on extent of reaction and average temperature was delineated.     

Impedance spectroscopy of V2O5–Bi2O3–BaTiO3 glass–ceramics

The glasses within composition as: (80 − x)V₂O₅/20Bi₂O₃/xBaTiO₃ with x = 2.5, 5, 7.5 and 10 mol% have been prepared. The glass transition (T_g) increases with increasing BaTiO₃ content. Synthesized glasses ceramic containing BaTi₄O₉, Ba₃TiV₄O₁₅ nanoparticles of the order of 25–35 nm and 30–46 nm, respectively were estimated using XRD. The dielectric properties over wide ranges of frequencies and temperatures were investigated as a function of BaTiO₃ content by impedance spectroscopy measurements. The hopping frequency, ω_h, dielectric constant, ε′, activation energies for the DC conduction, E_σ, the relaxation process, E_c, and stretched exponential parameter β of the glasses samples have been estimated. The, ω_h, β, decrease from 51.63 to 0.31 × 10⁶ (s⁻¹), 0.84 to 0.79 with increasing BaTiO₃ respectively. Otherwise, the E_σ, increase from 0.279 to 0.306 eV with increasing BaTiO₃. The value of dielectric constant equal 9.5·10³ for the 2.5BaTiO₃/77.5V₂O₅/20Bi₂O₃ glasses-ceramic at 330 K for 1 KHz which is ten times larger than that of same glasses composition. Finally the relaxation properties of the investigated glasses are presented in the electric modulus formalism, where the relaxation time and the respective activation energy were determined.     

Infrared,Raman and XPS spectroscopic studies of Bi2O3–B2O3–Ga2O3 glasses

Glasses with compositions 60Bi₂O₃–(40?x)B₂O₃–xGa₂O₃ (x = 5, 10, 15, 20 mol%) are prepared by conventional melting method. The thermal properties are investigated by differential thermal analysis (DTA) and the structures of the glasses were probed by Infrared, Raman and X-ray photoelectron spectroscopy (XPS). The results show that density, refractive index and optical basicity increase with the increase of Ga₂O₃. The glass transition temperature (T_g), the onset crystallization temperature (T_x), ΔT (T_x?T_g) decrease with the content of Ga₂O₃. The cut-off edges in ultraviolet and infrared shift to longer wavelength with the increase of Ga₂O₃. On the other hand, the addition of Ga₂O₃ causes a progressive coordination number change of the boron atom from 3 to 4. XPS result indicates both Bi⁵⁺ and Bi³⁺ exist in 5 mol% Ga₂O₃ content, while Bi⁵⁺ amounts decrease with the increase of Ga₂O₃ contents. The glass is mainly composed of [BiO₆], [BO₃], [BO₄] and [GaO₄] polyhedra. Glasses are supposed to have layer structure. [BO₃] triangle and [BO₄] tetrahedra may be located between the [GaO₄] tetrahedral and [BiO₆] octahedra to prevent crystallization and to compensate electric charge.     

Preparation and characterization of SO4 2−/Fe2O3–TiO2–Nd2O3 catalyst

This paper reports on the preparation of SO₄ ^2?/Fe₂O₃–TiO₂–Nd₂O₃ (SFTN) by combustion method. The effect of Nd content on catalytic activity was investigated. The prepared materials doped and undoped by Nd were compared by means of TG-DTG, XRD, FT-IR, NH₃-TPD and TEM techniques. Results indicated that the introduction of Nd improved the catalytic activities of the catalysts. Catalytic activity of SFTN was the highest with 98.3 % menthol conversion when Nd content was at 2 wt%. The introduction of Nd stabilized the coordination bond between the sulfate irons and the metallic oxides, helping in the formation of solid acid sites, enhancing the dispersion of catalyst particles, and inhibiting the growth of catalyst particles under heating.     

Comparative studies in subsolidus areas of ternary oxide systems PbO–V2O5–In2O3 and PbO–V2O5–Fe2O3

Thermal stability of PbO was studied. Reactivity of oxides in the systems PbO–M₂O₃ (M = In, Fe) was investigated up to 650 °C. Using the DTA and XRD methods, parts of investigated ternary oxide systems, labelled by compounds: V₂O₅, Pb₈V₂O₁₃ and M₂O₃ (M = In, Fe), have been divided into partial ternary systems. IR spectra of compounds Pb₂MV₃O₁₁ (M = In, Fe) have been compared.     

Infrared,Raman and XPS spectroscopic studies of Bi2O3–B2O3–GeO2 glasses

Glasses with composition 50Bi₂O₃–(50 ? x) B₂O₃–xGeO₂ (x = 0, 5, 10, 15 mol%) were prepared by conventional melting method. The thermal properties were investigated by differential thermal analysis (DTA) and the structures of the glasses were probed by Infrared, Raman and X-ray photoelectron spectroscopy (XPS). The results show that density, refractive index and optical basicity increase with the increase of GeO₂. The glass transition temperature (T_g), onset crystallization temperature (T_x) and ΔT (T_x ? T_g) increase as well. The cut-off edges in ultraviolet and infrared shift to longer wavelength by the addition of GeO₂. Infrared, Raman and XPS results indicate that the glass network consists of [Bi–O₆] octahedron, [BO₃] triangle, [BO₄] tetrahedron and [GeO₄] tetrahedron and borate oxide mainly exists in [BO₃] units. XPS result indicates Ge⁴⁺ ions form steady [GeO₄] tetrahedra units in the glass network and the number of non-bridging oxygens decreases with the addition of GeO₂.     

Effects of nano-YAG (Y3Al5O12) crystallization on the structure and photoluminescence properties of Nd3+-doped K2O–SiO2–Y2O3–Al2O3 glasses

Nd³⁺-doped precursor glass in the K₂O–SiO₂–Y₂O₃–Al₂O₃ (KSYA) system was prepared by the melt-quench technique. The transparent Y₃Al₅O₁₂ (YAG) glass–ceramics were derived from this glass by a controlled crystallization process at 750 °C for 5–100 h. The formation of YAG crystal phase, size and morphology with progress of heat-treatment was examined by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and Fourier transformed infrared reflectance spectroscopy (FT-IRRS). The crystallite sizes obtained from XRD are found to increase with heat-treatment time and vary in the range 25–40 nm. The measured photoluminescence spectra have exhibited emission transitions of ⁴F_3/2 → ⁴I_J (J = 9/2, 11/2 and 13/2) from Nd³⁺ ions upon excitation at 829 nm. It is observed that the photoluminescence intensity and excited state lifetime of Nd³⁺ ions decrease with increase in heat-treatment time. The present study indicates that the incorporation of Nd³⁺ ions into YAG crystal lattice enhance the fluorescence performance of the glass–ceramic nanocomposites.     

Phase Diagrams of Fullerenol-d–LaCl3–H2O and Fullerenol-d–GdCl3–H2O Systems at 25°С

Russian Journal of Physical Chemistry A - Isothermal phase diagrams of ternary systems fullerenol-d–LaCl3–H2O and fullerenol-d–GdCl3–H2O at 25°C are studied via...     

Structure and properties of glasses in the system Li2O–SnO–B2O3

Glasses in the system Li₂O–SnO–B₂O₃ system were prepared by a melt-quenching method. Thermal and viscous properties and local structure of these glasses were investigated. The SnO–B₂O₃ glasses exhibited relatively low glass-transition temperatures (T_g) around 350 °C and excellent thermal stability against crystallization. Viscosity measurements in the vicinity of T_g indicated that the glasses were considerably fragile compared to alkali borate glasses. Fraction of four-coordinated boron was maximized at the composition with 50 mol% SnO and that of nonbridging oxygen, which is not purely ionic in alkali borate systems but partially covalent, augmented with an increase in the SnO content. Correlation between glass properties and structure was discussed in the SnO–B₂O₃ binary system.     

Structural relaxation of PbO–WO3–P2O5 glasses

The structural relaxation of three compositional series of PbO–WO₃–P₂O₅ glasses with composition (0.5 ? x/2)PbO·xWO₃·(0.5 ? x/2)P₂O₅, x = 0, 0.1, 0.2, 0.3, 0.4, and 0.5; 0.5PbO·xWO₃·(0.5 ? x)P₂O₅, x = 0, 0.1, 0.2, and 0.3; and (0.5 ? x)PbO·xWO₃·0.5P₂O₅, x = 0, 0.1, 0.2, 0.3, 0.4, and 0.5 was studied by thermomechanical analysis. The structural relaxation was studied in the transformation region using the Tool–Narayanaswamy–Moynihan’s and Tool–Narayanaswamy–Mazurin’s models. The relaxation function of Kohlrausch Williams and Watts was used. The parameters of both models were calculated by nonlinear regression analysis of thermodilatometric curves measured by thermomechanical analyzer under the constant load. Both models very well describe the experimental data. It was found that the modulus is increasing with increasing amount of WO₃ in all glasses. On the contrary, the width of the spectrum of relaxation times is decreasing with increasing amount of WO₃ in all studied glasses. Both models possess the values of metastable melt thermal expansion coefficient equal to their experimental value.     

Influence of SrO content on microstructure and crystallization of glazes in the SiO2–Al2O3–CaO–MgO–K2O system

The effect of the SrO addition on the microstructure and structure of the glazes from the SiO₂–Al₂O₃–CaO–MgO–K₂O system was investigated in this study. The results were obtained by testing the ability of the frits crystallization, the stability of the crystallizing phases during the single-step fast-firing cycle depending on their chemical composition and the effect of addition of strontium oxide. Differential scanning calorimetry (DSC) curves showed that all glazes crystallized, and diopside and anorthite were mainly identified as dominant phases in the obtained glazes, while the size and amount of each depended on the amount of SrO introduced. The thermal characteristic of the frits was carried out using DSC, and crystalline phases were determined by X-ray diffractometry. The glaze microstructure was investigated by scanning electron microscopy and transmission electron microscopy. Additional information on the microstructure of frits was derived from spectroscopic studies in the mid-infrared range.

     

Investigation of phase equilibria in the Er2O3–Na2O–P2O5 system: the partial system ErPO4–NaPO3–Er(PO3)3

The partial system ErPO₄–NaPO₃–Er(PO₃)₃ of the Er₂O₃–Na₂O–P₂O₅ oxide system has been investigated by thermoanalytical methods and X-ray powder diffraction. On the basis of the obtained results the phase diagram of the partial system is proposed. The system is bounded by three subsystems: (i) ErPO₄–Er(PO₃)₃, (ii) Er(PO₃)₃–NaPO₃ and (iii) ErPO₄–NaPO₃. Their phase diagrams are proposed. In the Er(PO₃)₃–NaPO₃ subsystem an intermediate compound NaEr(PO₃)₄ occurs; it melts incongruently at 655 °C. It was found that ErPO₄ and NaEr(PO₃)₄ form a section which is a real system only in the subsolidus region (below 646 °C). Two ternary invariant points (one ternary peritectic and one ternary eutectic) occur in the investigated partial system ErPO₄–NaPO₃–Er(PO₃)₃.     

Phases in the subsolidus area of the system CuO–V2O5–Fe2O3

The phase equilibria in the solid state in the system FeVO₄?CCu₃V₂O₈ and FeVO₄?CCuO have been determined. Based on the obtained DTA and XRD analysis results and some additional research, a phase diagram in the whole subsolidus area of the system CuO?CV₂O₅?CFe₂O₃ has been worked out. Eighteen subsidiary subsystems can be distinguished in this ternary system. Basic properties of the obtained phases with howardevansite- and lyonsite-type structure have been investigated by DTA, IR, and SEM methods.     

Study of ceramic pigments based on cobalt doped Y2O3–Al2O3 system

Ceramic pigments based on Y₂O₃–Al₂O₃ system doped by cobalt as a colourant agent were synthesized by solid-state reaction at temperatures up to 1,400 °C. The reactivity of initial mixtures of components was improved by the mineralizer LiF and the mechanical activation in a planetary ball mill. The temperature region of the product formation was followed by the method of thermal analysis. The effect of the synthetic method on the phase composition of the products was studied by X-ray diffraction analysis. Studied pigment-application properties of the product include the measurement of optical properties in the visible region of light and particle size distribution. The simple solid-state reaction led to the formation of turquoise samples that contain mainly blue CoAl₂O₄ spinel and next to it also YAlO₃ perovskite and Y₃Al₅O₁₂ garnet phases. The mineralizer LiF promotes the formation of yttrium aluminium double oxides of sandy-yellow to grey–brown colour hue, although the samples also contain small amount of blue CoAl spinel phase. Intensive milling process did not results in CoAl spinel phase and the samples contain yttrium aluminium perovskite and cobalt oxide. Evaluation of Kubelka–Munk absorption as a function of the pigment concentration was found that hiding is complete by adding of 5 mass% of pigment to the ceramic glaze. Resulting colour hue of all pigment applications into ceramic glaze is blue. The size of particles lies in the range of 7–26 μm.     

Distribution of species in Na2O–CaO–B2O3 glasses as probed by FTIR

The article presents a simple method that can be used to get the concentration of various species in mixed-modifier borate glasses. By using the fraction of four coordinated boron in xCaO (30 − x)Na₂O70B₂O₃ (0 ≤ x ≤ 27.5 mol%) and xCaO(40 − x)Na₂O60B₂O₃ glasses (10 ≤ x ≤ 40 mol%), the concentration of BO₄⁻ and asymmetric BO₃ units related to each modifier oxide could be determined. CaO has a greater tendency to form asymmetric BO₃ units in the first glass series, while Na₂O has the ability to form BO₄ units to a greater extent. In xCaO(40 − x)Na₂O60B₂O₃ glasses, BO₄⁻ and asymmetric BO₃ units are formed at the same rate from Na₂O and CaO. The fraction of four coordinated boron, can be predicted by treating the studied glasses as if they are mixtures of Na₂O–B₂O₃ and CaO–B₂O₃ matrices. The change in N₄ is due to change in the relative concentration of these matrices.     

ZrO2–Sc2O3 Solid Electrolytes Doped with Yb2O3 or Y2O3

Russian Journal of Electrochemistry - The effects of the Y2O3 and Yb2O3 co-doping impurities on the transport characteristics and stabilization of the cubic phase in solid solutions based on...     

Rheological Properties of the Hydrated Al2O3–TiO2System

The rheology of mixtures of hydrated aluminum oxide and hydrated titanium dioxide sols was investigated. It was shown that flow curves depend on the mixture composition, the age of initial sols, the contact time of components, and the temperature. At low deformation rates, particles are aligned with the flow; this effect is partially reversible. At high shear rates, a discontinuity appears in the system; the effect depends on the age of initial sols.     

Mullitization behavior and microstructural development of B2O3–Al2O3–SiO2 mixtures activated by high-energy ball milling

This paper reports on phase formation and microstructural development of mullite, derived from B₂O₃–Al₂O₃–SiO₂ mixtures activated with different milling methods. It is found that the addition of B₂O₃ has a positive effect on mullite phase formation from the mixture of Al₂O₃–SiO₂, which can be qualitatively attributed to the fact that B₂O₃ brought out higher nucleation density and enhanced reaction kinetics. Anisotropic grain growth of mullite was not observed in the unmilled mixture since mullite phase formation occurred after densification. Dense and interlocking microstructures of mullite ceramics were produced from the mixture activated with stainless steel milling media, whereas mullite whiskers were formed in the samples milled with tungsten carbide media. The high-energy ball milling refined the precursors and thus reduced the mullitization temperature. As a result, anisotropic microstructures and mullite whiskers could be derived from the milled mixtures. This way to produce anisotropic microstructures of mullite ceramics is very simple and requires temperatures much lower than those reported in the literature. This method is believed to be useful to fabricate reinforced mullite or mullite-related materials via in-situ anisotropic grain growth.     

Phase diagram studies of methanol–CHF3 and methanol–H2O–CHF3 mixtures

Comprehensive phase diagrams of methanol/CHF₃ and methanol/H₂O/CHF₃ mixtures over the temperature range of 25–100°C and pressure range of atmospheric to 340 atm are reported. Fluoroform is expected to be useful as an alternative to CO₂ for enhancing the fluidity of liquid mixtures due to its high polarity and low viscosity. Therefore, these mixtures will be studied as mobile phases for enhanced-fluidity liquid chromatography and extraction. The phase behavior of methanol/CHF₃ and methanol/H₂O/CHF₃ was compared to that of methanol/CO₂ and methanol/H₂O/CHF₃. Fluoroform is markedly more miscible with methanol or methanol/H₂O than is CO₂. Data for methanol/CHF₃ binary mixtures were also modeled by the Peng–Robinson equation of state. The correlation results showed that the PR equation of state with two temperature-independent binary parameters was capable of representing the experimental data over the entire temperature range with an average relative deviation within 6%.