Structural and Temperature Dependent Electrical Conductivity Properties of Dy<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sm<Subscript>2</Subscript>O<Subscript>3</Subscript> CO-Doped Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>

In the present work, Dy₂O₃ and Sm₂O₃ double-doped Bi₂O₃-based materials are synthesized by exploiting the solid-state synthesis method. The structural and temperature dependent electrical properties of these ternary ceramic samples, which are candidate materials for solid oxide fuel cell (SOFCs) electrolyte, are determined by means of a powder X-ray diffractometer (XRD), the four point-probe method (FPPM), and the thermal-gravimetry/differential thermal analysis (TG/DTA). As a result of the XRD measurements, the fluorite-type fcc δ-phase with a stable structure is obtained for higher values of the dopant oxide material, which are the samples with the maximum content of fixed 20% Dy₂O₃ and 15% and 20% Sm₂O₃. The samples with the stable δ-phase structure have higher conductivities. The highest electrical conductivity is found for the (Bi₂O₃)0.6(Dy₂O₃)_0.2(Sm₂O₃)_0.2 sample, which was 2.5×10^–2 (Ohm cm)^–1 at 750 °C. The activation energies are also calculated from the Arrhenius charts, which were determined from the FPPM measurements. The lowest activation energy is found as 0.85 eV for the sample with the highest electrical conductivity.     

Glass Formation in the Ternary System La<Subscript>2</Subscript>O<Subscript>3</Subscript>–As<Subscript>2</Subscript>S<Subscript>3</Subscript>–Er<Subscript>2</Subscript>O<Subscript>3</Subscript>

The boundaries of the glass formation region in the ternary system La₂O₃–As₂S₃–Er₂O₃ were found. Transparent glass of composition (La₂O₃)_0.03(As₂S₃)0.90(Er₂O₃)0.07 was studied by X-ray photoelectron and Raman spectroscopy. The intensities of the bands characterizing As–S, La–O, and Er–O bonds increased, and these bands were shifted toward higher energies. This was due to an increase in the covalence of these bonds and probably due to the formation of new bonds in the glasses. Samples in the glass formation region are resistant at 300 K to air, water, and organic solvents.     

Formation of solid solutions of multiferroics in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The sequence of phases appearance during the formation of Bi_1–xNd_xFeO₃ solid solutions in powder oxides mixtures of bismuth, neodymium, and iron has been determined. It has been shown that the closeness of the reaction mixture composition to that of the individual compound (BiFeO₃ or NdFeO₃) is essential for the realization of the series of phase transformations yielding solid solutions of multiferroics Bi_1–xNd_xFeO₃ as the final product, due to the prevalence of various interphase contacts in the starting reaction zone.     

Synthesis and properties of γ-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> solid solutions

The textural and structural properties of mixed oxides Ga₂O₃–Al₂O₃, obtained via impregnating γ-Al₂O₃ with a solution of Ga(NO₃)₃ and subsequent heat treatment, are studied. According to the results from X-ray powder diffraction, gallium ions are incorporated into the structure of aluminum oxide to form a solid solution of spinel-type γ-Ga₂O₃–Al₂O₃ up to a Ga₂O₃ content of 50 wt % of the total weight of the sample, accompanied by a reduction in the specific surface area, volume, and average pore diameter. It is concluded that when the Ga₂O₃ content exceeds 50 wt %, the β-Ga₂O₃ phase is observed along with γ-Ga₂O₃–Al₂O₃ solid solution. ⁷¹Ga and ²⁷Al NMR spectroscopy shows that gallium replaces aluminum atoms from the tetrahedral position to the octahedral coordination in the structure of γ-Ga₂O₃–Al₂O₃.     

Modifying additives affect the properties of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

The effects caused by modifying additives, namely nonionic surfactants (Tween 80 and Neonol AF 9-6) and oxides (B₂O₃ and HfO₂), on the rheology, film formation, and phase formation in the yttrium aluminum silicate system prepared by sol–gel technology were studied. The effect of 1 wt % HfO₂ additions on the activation energy of crystallization was studied.     

Thermal studies of ZnO–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–TeO<Subscript>2</Subscript> glasses

The effect of TeO₂ additions on the thermal behaviour of zinc borophosphate glasses were studied in the compositional series (100 − x)[0.5ZnO–0.1B₂O₃–0.4P₂O₅]–xTeO₂ by differential scanning calorimetry, thermodilatometry and heating microscopy thermal analysis. The addition of TeO₂ to the starting borophosphate glass resulted in a linear increase of glass transition temperature and dilatometric softening temperature, whereas the thermal expansion coefficient decreased. Most of glasses crystallize under heating within the temperature range of 440–640 °C. The crystallization temperature steeply decreases with increasing TeO₂ content. The lowest tendency towards crystallization was observed for the glasses containing 50 and 60 mol% TeO₂. X-ray diffraction analysis showed that major compounds formed by annealing of the glasses were Zn₂P₂O₇, BPO₄ and α-TeO₂. Annealing of the powdered 50ZnO–10B₂O₃–40P₂O₅ glass leads at first to the formation of an unknown crystalline phase, which is gradually transformed to Zn₂P₂O₇ and BPO₄ during subsequent heating.     

Atmospheric control of gel-oxide transformation in sol–gel derived Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript> fibers

Via sol–gel processing metal–organic fibers were produced and dried up to 140 °C. For these gel fibers the influence of a treatment in different atmospheres was investigated for the temperature range of 200–850 °C. The atmospheres were nitrogen, water vapor, evaporated nitric and hydrochloric acid and evaporated hydrogen peroxide. In the presence of moisture and especially with acidic moisture fibers were transformed almost completely to their oxide composition (82 mol% Al₂O₃·18 mol% Y₂O₃). In these inorganic amorphous structures considerable differences were observed on several structural levels. On the atomic scale, the coordination of Al ions was investigated by ²⁷Al MAS NMR and skeletal density by He-pycnometry. Porosity in the nm scale was characterized by N₂-sorption. As a macroscopic effect of different treatment atmospheres, the longitudinal shrinkage was observed. For fibers treated at 500 °C the relative shrinkage varied by 100% (comparing water vapor and nitrogen atmosphere). No simple correlation between the release of organic constituents, the formation of porosity and the shrinkage could be found. These aspects were controlled by the rigidity of the inorganic network against atomic reconstitution. The kind of atmosphere was found to be an effective parameter to control various aspects of the xerogel structure.     

New continuous solid solution in the Zn<Subscript>2</Subscript>InV<Subscript>3</Subscript>O<Subscript>11</Subscript>–Mg<Subscript>2</Subscript>InV<Subscript>3</Subscript>O<Subscript>11</Subscript> system

In this study, mechanical activation process was used for intimate mixing as well as producing finely ground particles, increased surface area and improved chemical reactivity of milled materials for producing SrTiO₃ from commercially pure strontium carbonate and TiO₂ as a contributive process. Characterization of milled powder mixture by X-ray diffraction analysis showed that disappearing, decreasing and/or shifting of the patterns occurred with mechanical activation that means amorphization was taken place. Amorphization was also demonstrated by FT-IR analysis where shift of band centers as well as the decrement of transmittance related to CO₃ was observed. Advantage of amorphization was established with high-temperature XRD analysis which showed 1300 °C was not enough for non-activated mixture to form SrTiO₃, whereas structure only composed of SrTiO₃ at 1000 °C for activated ones. The reason for this phenomenon was investigated by DTA-TG analysis, and it was based on energy accumulation originated from mechanical activation that corresponds to peak temperature shifting to the lower temperatures and CO₂ liberation at mechanical activation step arising from local temperature rising at the vial during high-energy milling that was understood from peak temperature, and area decrement of endothermic peak corresponds to decomposition of SrCO₃.     

Thermal analysis of the (Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>1−x</Subscript>(Y<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>x</Subscript> pigments

The synthesis of new compounds based on Bi₂O₃ is investigated because they can be used as new ecological inorganic pigments. Chemical compounds of the (Bi₂O₃)_1−x(Y₂O₃)_x type were synthesized. The host lattice of these pigments is Bi₂O₃ that is doped by Y³⁺ ions. The incorporation of doped ions provides the interesting colours and contributes to a growth of the thermal stability of these compounds. The simultaneous TG-DTA measurements were used for determination of the temperature region of the pigment formation and thermal stability of pigments. This paper also contains the results of the pigment characterization by X-ray powder diffraction and their colour properties.     

Concentration Space of Homogeneous Garnet in the System Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–(Y,Bi)<Subscript>3</Subscript>(Fe,Ga)<Subscript>5</Subscript>O<Subscript>12</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>

The concentration space of homogeneous garnet in the system Ga₂O₃–(Y, Bi)₃(Fe, Ga)₅O₁₂–Fe₂O₃ was determined by X-ray powder diffraction analysis. The obtained results expand the knowledge of the possible variations of cation ratios Y : Bi : Fe : Ga in garnet, which can be used for searching for and creating new stable magneto-optical materials.     

Reduction of Oxide Mixtures of (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> + CuO) and (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> + Co<Subscript>3</Subscript>O<Subscript>4</Subscript>) by Low-Temperature Hydrogen Plasma

The paper presents experimental results pertaining to the reduction of oxide mixtures namely (Fe₂O₃ + CuO) and (Fe₂O₃ + Co₃O₄), by low-temperature hydrogen plasma in a microwave hydrogen plasma set-up, at microwave power 750 W and hydrogen flow rate 2.5 × 10^?6 m³ s^?1. The objective was to examine the effect of addition of CuO or Co₃O₄, on the reduction of Fe₂O₃. In the case of the Fe₂O₃ and CuO mixture, oxides were reduced to form Fe and Cu metals. Enhancement of reduction of iron oxide was marginal. However, in the case of the Fe₂O₃ and Co₃O₄ mixture, FeCo alloy was formed within compositions of Fe₇₀Co₃₀, to Fe₃₀Co₇₀. Since the temperature was below 841 K, no FeO formed during reduction and the sequence of Fe₂O₃ reduction was found to be Fe₂O₃ → Fe₃O₄ → Fe. Reduction of Co₃O₄ preceded that of Fe₂O₃. In the beginning, the reduction of oxides led to the formation of Fe–Co alloy that was rich in Co. Later Fe continued to enter into the alloy phase through diffusion and homogenization. The lattice strain of the alloy as a function of its composition was measured. In the oxide mixture in which excessive amount of Co₃O₄ was present, all the Co formed after reduction could not form the alloy and part of it appeared as FCC Co metal. The crystallite size of the alloy was in the range of 22–30 nm. The crystal size of the Fe–Co alloy reduced with an increase in Co concentration.     

Physicochemical properties of (CH<Subscript>3</Subscript>)<Subscript>2</Subscript>NH<Subscript>2</Subscript>Cl–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites

Composite solid electrolytes were synthesized from the organic salt dimethylammonium chloride (1–x)C₂H₈NCl–xAl₂O₃. Their physicochemical properties were studied. In the starting C₂H₈NCl salt, there is a phase transition at 39°C accompanied by an increase in conductivity by two orders of magnitude. The conductivity of the high-temperature phase is 9.3 × 10^–6 S/cm at 160°C. A differential scanning calorimetry study showed that the salt in the composites spreads over the oxide surface and at x > 0.6 the salt melting enthalpy decreases to zero. The conductivity of the resulting composites was studied by impedance spectroscopy. It was shown that heterogeneous doping leads to a sharp increase in ion conductivity to 7.0 × 10^–3 S/cm at 160°C and a decrease in the activation energy to 0.55 eV.     

Adsorption of chlorobenzene vapor on V<Subscript>2</Subscript>O<Subscript>5</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst under dynamic conditions

Adsorption dynamics of chlorobenzene vapors on a 5% V₂O₅/Al₂O₃ catalyst has been investigated using the frontal chromatography technique. The uptakes of chlorobenzene have been measured as a function of vapor concentration and adsorption equilibrium has been found to follow formally the Langmuir isotherm. The breakthrough time proved to be a linear function of the column length as expected. Breakthrough profiles have been reported for different experimental conditions and quantitatively fitted by a reduced lumped diffusion model. This model provides an analytical solution that facilitates engineering calculations. Model parameters show complex behavior as functions of stream characteristics and depend on column length. When empirical expressions relating model mass transfer coefficients with influencing variables are found the model demonstrates good accuracy in predicting column performance.     

Effects of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> on the crystallization and structure of CaO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> glass ceramics

Radiation-induced degradation of the weakly and strongly 4-vinylpyridine basic ion exchange resins by gamma radiolysis was investigated in the presence of air and liquid water. This study is focused on evaluating the radiolytic gases (H₂, CO, CO₂ and CH₄) and liquid products (water-solute TOC and NH₄ ⁺). The weakly basic resin yielded lower amounts of H₂ and CO and higher amounts of CO₂ than those of the strongly basic resin. Moreover, the strong basic resin tended to yield greater amounts of NH₄ ⁺. Resins were characterized by the FTIR spectroscopy technique and the results showed that the resins structures are relatively stable.     

Thermal properties of Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–PbO–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glass system

Thermal behavior of xGa₂O₃–(50 − x)PbO–50P₂O₅ (x = 0, 10, 20, and 30 mol.% Ga₂O₃) and xGa₂O₃–(70 − x)PbO–30P₂O₅ (x = 0, 10, 20, 30, and 40 mol.% Ga₂O₃) glassy materials were studied by thermo-mechanical analysis (TMA) and differential thermal analysis (DTA). Replacement of PbO for Ga₂O₃ is accompanied by increasing glass-transition temperature (263 ≤ T _g/°C ≤ 535), deformation temperature (363 ≤ T _d/°C ≤ 672), crystallization temperature (396 ≤ T _c/°C ≤ 640) and decreasing of coefficient of thermal expansion (5.1 ≤ CTE/ppm K⁻¹ ≤ 16.7). Values of Hruby parameter were determined (0.1 ≤ K _H ≤ 1.3). The thermal stability of prepared glasses increases with increasing of concentration of Ga₂O₃.     

Thermoelectric power and electrochemical studies on CdI<Subscript>2</Subscript>–Ag<Subscript>2</Subscript>O–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript> system

A quaternary super-ion-conducting system, 20CdI₂ − 80[xAg₂O − y(0.7V₂O₅ − 0.3B₂O₃)] where 1 ≤ x/y ≤ 3, has been prepared by melt quenching technique. The electrical conductivity measured was the order of 10⁻⁴  S/cm at room temperature. The values of silver-ion transport number obtained by electromotive force technique are nearly unity. The thermoelectric power and electrochemical studies were done on the CdI₂–Ag₂O–V₂O₅–B₂O₃ system. The discharge and polarization characteristics were examined for different cathodes to evaluate the utility of these cells as power sources for low energy applications.     

Crystal structure of Ba<Subscript>3</Subscript>[UO<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>2</Subscript>(NCS)]<Subscript>2</Subscript> · 9H<Subscript>2</Subscript>O

Single crystals of Ba₃[UO₂(C₂O₄)₂(NCS)]₂ · 9H₂O are synthesized and studied by X-ray diffraction. The crystals are orthorhombic, space group Fddd, Z = 16, and the unit cell parameters are a = 16.253(3) Å, b = 22.245(3) Å, c = 39.031(6) Å. The main crystal structural units are mononuclear complex groups [UO₂(C₂O₄)₂NCS]^3? of the crystal-chemical family (AB ₂ ⁰¹ M¹ (A = UO ₂ ²⁺ , B⁰¹ = C₂O ₄ ^2? , M¹ = NCS^?) of the uranyl complexes linked into a three-dimensional framework by electrostatic interactions and hydrogen bonds involving oxalate ions and water molecules.     

Pd/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for the selective liquid-phase hydrogenation of acetylene to ethylene

The structure of Ga₂O₃–Al₂O₃ supports and Pd/Ga₂O₃–Al₂O₃ catalysts and the performance of these catalysts in liquid-phase acetylene hydrogenation have been investigated. The deposition of Ga(NO₃)₃ onto Al₂O₃ by impregnation followed by calcination of the impregnated support at 600°C yields γ-Ga₂O₃–Al₂O₃ solid solutions containing up to 50 wt % Ga₂O₃. X-ray diffraction characterization of model palladium catalysts and their temperature-programmed reduction with hydrogen have demonstrated that, while palladium in Pd/Ga₂O₃ is in the form of a Pd₂Ga alloy, in the Pd/γ-Ga₂O₃–Al₂O₃ catalyst there is no direct interaction between PdО and Ga₂O₃ particles and palladium is in the monometallic state. The introduction of 10–20 wt % gallium oxide into Al₂O₃ lowers the activity of the supported palladium catalyst relative to that of the initial Pd/Al₂O₃ but increases the ethylene yield by enhancing the ethylene formation selectivity.     

Catalytic dehydrogenation of cyclohexene over MoO<Subscript>3</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

A series of MoO₃/γ-Al₂O₃ catalysts with different Mo surface densities (Mo atoms/nm²) has been prepared by incipient wetness impregnation method. Structural characteristics of the prepared catalysts were investigated by atomic absorption spectroscopy, X-ray diffraction, Fourier Transform Infrared spectroscopy, N₂ adsorption at −196 °C, and temperature-programmed reduction (TPR). The catalytic activities of the prepared catalysts were tested by cyclohexene conversion between 200 and 400 °C. XRD results indicated that molybdenum oxide species were dispersed as a monolayer on the support up to 4.04 Mo atoms/nm², and the formation of crystalline MoO₃ was observed above this loading. FTIR and TPR results showed that molybdenum oxide species were present predominantly in tetrahedral form at lower loading, and polymeric octahedral forms were dominant at higher loading. Cyclohexene conversion reaction proceeded mainly through the simple dehydrogenation pathway in the studied temperature range 200–400 °C and was found to be highly dependent on MoO₃ dispersion.     

Mass attenuation coefficients of B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript>–CaF<Subscript>2</Subscript> glass system at 0.662 and 1.25 MeV gamma energies

The total mass attenuation coefficients, partial interaction and the effective atomic numbers (Z_eff) of glass system (80−x)B₂O₃–10Al₂O₃–10SiO₂–xCaF₂ (where x = 5, 10, 20, 25, 30, 35 and 40 mol %) have been calculated at photon energies 0.662 and 1.25 MeV using the WinXCom software on the basis of mixture rule. Results indicated that the total mass attenuation coefficients showed a decrease with increasing the CaF₂ concentration, due to a decrease in Compton scattering probability, which gave a dominant contribution to the total mass attenuation coefficients for the studied glass samples at both energies. However, the photoelectric absorption and coherent scattering showed an increase with increasing the CaF₂, concentrations at same energies. For a comparison, the total mass attenuation coefficients of the glass system had lower values at the energy 1.25 MeV than that at 0.662 MeV. Z_eff was found to increase linearly with the increase of CaF₂ concentrations. It was concluded that low CaF₂ concentrations in glass system, under study, have Z_eff close to that of human tissue and have higher total absorption coefficients at energy of 0.662 MeV than that at 1.25 MeV. These results are very useful in designing gamma radiation detectors using thermoluminescence technique. Therefore, it is recommended to use low CaF₂ concentration of our glass system as good gamma detectors at energy of 1.25 MeV.