Partial least squares modeling of combined infrared, 1H NMR and 13C NMR spectra to predict long residue properties of crude oils

Research has been carried out to determine the potential of partial least squares (PLS) modeling of mid-infrared (IR) spectra of crude oils combined with the corresponding ¹H and ¹³C nuclear magnetic resonance (NMR) data, to predict the long residue (LR) properties of these substances. The study elaborates further on a recently developed and patented method to predict this type of information from only IR spectra. In the present study, PLS modeling was carried out for 7 different LR properties, i.e., yield long-on-crude (YLC), density (D_LR), viscosity (V_LR), sulfur content (S), pour point (PP), asphaltenes (Asph) and carbon residue (CR). Research was based on the spectra of 48 crude oil samples of which 28 were used to build the PLS models and the remaining 20 for validation. For each property, PLS modeling was carried out on single type IR, ¹³C NMR and ¹H NMR spectra and on 3 sets of merged spectra, i.e., IR + ¹H NMR, IR + ¹³C NMR and IR + ¹H NMR + ¹³C NMR. The merged spectra were created by considering the NMR data as a scaled extension of the IR spectral region. In addition, PLS modeling of coupled spectra was performed after a Principal Component Analysis (PCA) of the IR, ¹³C NMR and ¹H NMR calibration sets. For these models, the 10 most relevant PCA scores of each set were concatenated and scaled prior to PLS modeling. The validation results of the individual IR models, expressed as root-mean-square-error-of-prediction (RMSEP) values, turned out to be slightly better than those obtained for the models using single input ¹³C NMR or ¹H NMR data. For the models based on IR spectra combined with NMR data, a significant improvement of the RMSEP values was not observed neither for the models based on merged spectra nor for those based on the PCA scores. It implies, that the commonly accepted complementary character of NMR and IR is, at least for the crude oil and bitumen samples under study, not reflected in the results of PLS modeling. Regarding these results, the absence of sample preparation and the straightforward way of data acquisition, IR spectroscopy is preferred over NMR for the prediction of LR properties of crude oils at site.     

Solid-state high-resolution NMR studies on spin fluctuation associated with valence tautomerism of metal–benzoquinone system: Cobalt complex in the stable and meta-stable phases

Equilibrium between low-spin [Co^III(SQ)(Cat)(N–N)] and high-spin [Co^II(SQ)₂(N–N)] redox isomers, where SQ is semiquinonate (charge: −1, spin: 1/2), Cat is catecholate (charge: −2, spin: 0) and N–N is chelating nitrogen donor ligand, respectively, is a representative valence tautomeric phenomenon. To elucidate independently the spin state of the cobalt ion and that of benzoquinone-derived ligands in the solid state, we measured ¹³C MAS NMR spectrum of 3,5-di-t-butyl-1,2-benzoquinone and ²H MAS NMR spectrum of deuterated 2,2′-bipyridine for [Co(3,5-di-t-butyl-1,2-benzoquinone)₂(2,2′-bipyridine)] · x(C₆H₅CH₃) and its deuterated analogue in a temperature range of 200–350 K. Irreversible change of an effective magnetic moment μ_eff of a virgin sample was observed around 370 K due to a partial loss of crystal solvent and a change of crystal structure, whereas the sample annealed at 390 K showed a crystal structure different from the reported one and a reversible change of μ_eff, which is ascribed to equilibrium between Co(III)-form (S = 1/2) and Co(II)-form (S = 3/2). Based on the shifts and the number of NMR peaks for the annealed sample, we concluded that (1) interconversion between redox isomers occurs faster than NMR time scale (>10⁴ s⁻¹) in the solid state, (2) intraconversion between SQ and Cat in Co(III)-form also occurs much faster than 5 × 10⁴ s⁻¹ even at 198 K and (3) electron spins on SQ ligands in Co(II)-form are quenched probably due to a strong antiferromagnetic coupling between the two SQ ligands. The enthalpy and the entropy of the interconversion were estimated to be 17 kJ/mol and 54 J/(K mol), respectively. For the virgin metastable phase, SQ and Cat were clearly distinguished by ¹³C MAS NMR spectrum. The solid-state high-resolution NMR spectrum is useful to detect independently the change of spin states of benzoquinone-derived radical and metal ion.     

Functionalized N-heterocyclic carbene iridium complexes: Synthesis,structure and addition polymerization of norbornene

Picolyl, pyridine, and methyl functionalized N-heterocyclic carbene iridium complexes [Cp¹Ir(C^N)Cl]Cl (4, C^N = 3-Methyl-1-picolyimidazol-2-ylidene), [Cp¹Ir(C^N)Cl][Cp¹IrCl₃] (5), [Cp¹Ir(C-N)Cl]Cl (6, C-N = 3-Methyl-1-pyridylimidazol-2-ylidene) and [Cp¹Ir(L)Cl₂] (7, L = 1,3-dimethylimidazol-2-ylidene) have been synthesized by transmetallation from Ag(I) carbene species, and characterized by ¹H NMR, ¹³C NMR spectra and elemental analyses. The molecular structures of 5–7 have been confirmed by X-ray single-crystal analyses. The iridium carbene complexes 4 and 6 show moderate catalytic activities (3.03 × 10⁵ g PNB (mol Ir)^?1 h^?1 and 1.70 × 10⁶ g PNB (mol Ir)^?1 h^?1) for the addition polymerization of norbornene in the presence of methylaluminoxane (MAO) as co-catalyst. The produced polynorbornene have been characterized by IR, ¹H NMR and ¹³C NMR spectra, showing it follows the vinyl-addition-type of polymerization.     

INS,IR, RAMAN, 1H NMR and DFT investigations on dynamical properties of l-asparagine

Results of inelastic neutron scattering (INS), infra-red (IR), Raman and ¹H NMR spectroscopy used for investigations on the l-asparagine dynamics are reported. The crystallographic structure and experimental vibrational spectra are compared with those calculated by the DFT methods applied to the solid state. Very good conformity of the experimental and theoretical structures has been found. The NH₃⁺ torsional vibration mode is observed in the INS spectra at 494 cm⁻¹, while the bands assigned to the vibrations of the strong NH⋯O hydrogen bonds are observed at 2849, 2650, and 2480 cm⁻¹ in the IR spectrum. A ¹H NMR investigation has been carried out at 26.75 MHz in the temperature range 150–300 K. For l-asparagine the activation energy needed for the NH₃⁺ group reorientation is equal 5.6 kcal/mol.     

Ultrafiltration of mixed protein solutions of lysozyme and lactoferrin: role of modified inorganic membranes and ionic strength on the selectivity

Ultrafiltration of either single protein solutions (lysozyme 14,300 g mol⁻¹, pI=11; lactoferrin 80,000 g mol⁻¹, pI=8–9) or mixed protein solution was performed with inorganic membranes (MMCO 300,000 g mol⁻¹, pore radius 14 nm) chemically modified in order to bear either pyrophosphate (PP, anionic) or ethylenediamine (EDA, cationic) groups.The electrophoretic mobility of modified and unmodified zirconia particles fouled with proteins was similar whatever the grafted groups, meaning that the membrane surface was always made of adsorbed proteins during UF. In spite of that, for the UF of lysozyme/lactoferrin mixed solution, the maximum selectivity (S=lysozyme transmission/lactoferrin transmission=165) was observed with the EDA membrane and allowed an instantaneous purity of lysozyme in the permeate close to 100% to be achieved. Such high selectivitiy was mainly due to the negligible transmission of lactoferrin with the membrane modified with the EDA groups in the ionic strength range 0–100 mmol l⁻¹ of NaCl at pH 7 (achieved either for mixed and single solutions).     

Two-dimensional Pure Isotropic Proton Solid State NMR

One key bottleneck of solid-state NMR spectroscopy is that ¹H NMR spectra of organic solids are often very broad due to the presence of a strong network of dipolar couplings. We have recently suggested a new approach to tackle this problem. More specifically, we parametrically mapped errors leading to residual dipolar broadening into a second dimension and removed them in a correlation experiment. In this way pure isotropic proton (PIP) spectra were obtained that contain only isotropic shifts and provide the highest ¹H NMR resolution available today in rigid solids. Here, using a deep-learning method, we extend the PIP approach to a second dimension, and for samples of L-tyrosine hydrochloride and ampicillin we obtain high resolution ¹H-¹H double-quantum/single-quantum dipolar correlation and spin-diffusion spectra with significantly higher resolution than the corresponding spectra at 100 kHz MAS, allowing the identification of previously overlapped isotropic correlation peaks.     

Study on β-cyclodextrin inclusion of Zn(II) aromatic complex and its analytical application

A new β-cyclodextrin (β-CD) inclusion compound Zn(2H1NA)₂·2β-CD (2H1NA = 2-hydroxy-1-naphthoic acid) was prepared. The structure was characterized by ¹H NMR, IR, the fluorescence spectra, thermogravimetric analysis (TG–DTA) and elementary analysis. Meanwhile, the mechanism of the formation of the supramolecular system (2H1NA:Zn(II):β-CD) was studied and discussed by spectrofluorimetry. The results showed that the naphthalene rings of the Zn(II) aromatic complex Zn(2H1NA)₂ were encapsulated within the β-CD's cavity to form a 2:1 stoichiometry host–guest compound. The inclusion constant calculated was 1.27 × 10⁴ (L/mol)². A spectrofluorimetric method for the determination of 2H1NA in bulk aqueous solution in the presence of β-CD was developed based on the great enhancement of the fluorescence intensity of 2H1NA. The linear relationship was obtained in the range of 9.00 × 10^?7 to 2.50 × 10^?5 mol/L and the detection limit was 8.00 × 10^?7 mol/L. The proposed method was successfully applied to determine 2H1NA in waste water with recoveries of 97–104%.     

Synthesis and structure elucidation of 25,26,27,28-tetramethylcalix[4]arene tetraketone using 1D and 2D NMR spectroscopies

The ¹H and ¹³C NMR spectra of the new calix[4]arene-based tetraketone were completely assigned by one- and two-dimensional homo- and heteronuclear experiments (¹H–¹H COSY, ¹H–¹³C HMQC, and HMBC) at 400 and 100 MHz, respectively, at 25 °C standard pulse sequence. ¹H and ¹³C spectra were measured at room temperature for 25,26,27,28-tetramethylcalix[4]arene tetraketone (1). ¹³C{¹H}, DEPT and NMR techniques were used to distinguish the methyl, methylene and methine carbon resonance signals of calix[4]arene 1. Correlation of 1D (¹H, ¹³C{¹H}, DEPT) and 2D (HMQC and HMBC) NMR data was used to completely assign various overlapping and broad signals of calix[4]arene 1. Heteronuclear multibond correlation (HMBC) studies were used to completely assign various carbon resonances. Our results show that the conformation of calix[4]arene 1 in the solution is very similar to the cone conformation reported in the literature.     

Analysis and identification of irradiated Spirulina powder by a three-step infrared macro-fingerprint spectroscopy

A three-step infrared (IR) macro-fingerprint method combining conventional IR spectra, and the secondary derivative spectra with two-dimensional infrared correlation spectroscopy (2D-IR), was developed to analyze Spirulina powder before and after gamma irradiation. In the IR spectra, most of the absorption peaks of samples irradiated at 1, 2.7, 6, and 10.4 kGy had lower intensities than the non-irradiated ones, whereas peaks at 1152, 1078, and 1051 cm⁻¹ were slightly enhanced with irradiation at 2.7, 6, and 10.4 kGy. Their second derivative spectra amplified the differences and revealed that irradiation affected the C=O band of carboxylic acid and esters, and the N–H band of proteins. The peaks at 1746 and 1741 cm⁻¹, and those at 1730 and 1725  cm⁻¹ became two broad peaks. Meanwhile, the three sharp peaks at 1548 cm⁻¹, 1544 cm⁻¹ and 1536 cm⁻¹ changed to two broad peaks at around 1547 and 1534 cm⁻¹ after irradiation at doses higher than 1 kGy. The characteristic IR bands from 1700 cm⁻¹ to 1600 cm⁻¹, which represent the C=O band in proteins, also have different shapes and intensities after irradiation. The finding indicated that irradiation affected the secondary structures of protein which was confirmed by curve fitting results. During the process of increasing the temperature from 50 to 210 °C, the ratio of amide I to II in absorption intensities in the 2D-IR spectra of the irradiated samples varied with different response for different samples. Saccharides in Spirulina powder had a higher thermostability than proteins, but the autopeaks of irradiated samples did show differences from the non-irradiated sample. The intensity of autopeaks at 1012 cm⁻¹ increased dramatically in the irradiated samples while that of peaks at 1053, 1071, and 1083 cm⁻¹ decreased after irradiation. Based on the three-step IR macro-fingerprint method, irradiated Spirulina powder samples were successfully and fast identified and discriminated.     

Reduction reactions of bovine serum albumin and lysozyme by CO- .2 radical in polyvinyl alcohol solution: a pulse radiolysis study

Pulse radiolytic reduction of bovine serum albumin (BSA) and lysozyme by CO^⨪₂ radical in presence of polyvinyl alcohol (PVA) has been studied. At pH 6.8 in presence of 2% (w/v) PVA, reduction of BSA and lysozyme (both at 1×10⁻⁴ mol dm⁻³) give an additional transient peak at 390 nm along with the usual 420 nm peak. The bimolecular rate constants for the reaction of CO^⨪₂ radical at pH 6.8±0.2 with BSA are 2.7×10⁸ and 7.13×10⁸ dm³ mol⁻¹ s⁻¹ at 420 nm and 390 nm respectively. The same for lysozyme are 3.2×10⁸ and 5.6×10⁸ dm³ mol⁻¹ s⁻¹ at 420 nm and 390 nm, respectively. Dimethyl disulfide also gives 390 nm and 420 nm peaks in this system upon reduction with CO^⨪₂ radical. The 390 nm peak is ascribed to the sulfenium radical (RSS(H)R). Studies on the variation of pH suggests the protonation of RSSR^⨪ radical (420 nm) to form RSS(H)R radical (390 nm) in this viscous media. The decay of RSS(H)R radical occurs via formation of RS radical and RS(H)S(H)R, the final product being RSH in both cases.     

FTIR investigation of spray-dried milk protein concentrate powders

Fourier transform infrared (FTIR) spectroscopy was used to examine the conformation of proteins in spray-dried milk protein concentrate (MPC) powders and to determine if the spectral changes could be related to nitrogen solubility of these powders. MPC samples (83–92% protein, dry basis) were prepared using a range of processing conditions and stored for 4 weeks at 21 °C. FTIR spectra were collected in the mid infrared (MIR) region between 4000 and 600 cm⁻¹. FTIR data was pre-processed to remove physical effects causing discrimination between samples using firstly second derivatives and normalization and secondly the extended multiplicative scatter correction (EMSC) technique. The FTIR spectral changes were subsequently assessed using second derivative spectroscopy and principal components analysis (PCA) in the amide I and II regions (1700–1400 cm⁻¹) and the fingerprint region (1800–700 cm⁻¹). PCA analysis showed that the different powder preparations could be separated on scores plots but the separation was not related to nitrogen solubility per se. However, changes in nitrogen solubility of individual MPC powders during storage could be correlated to changes in FTIR spectra. PCA analysis of FTIR spectra could generally discriminate between MPC powders that had lost significant nitrogen solubility (9–20%) and those in which nitrogen solubility was preserved on storage. There were changes in intensity and/or position of bands at 1630 cm⁻¹ when the solubility of a stored sample decreased substantially. The results of this work also show that EMSC data pre-processing for these samples gives comparable results when compared with more complicated data pre-processing for the removal of physical effects.     

A new C21-steroidal glycoside from Cynanchum stauntonii

A new C21-steroidal glycoside with two known compounds were isolated from the root of Cynanchum Stauntonii.Based on thespectral analysis,including MS,1H NMR,13C NMR,DEPT,1H-1H COSY,13C-1H COSY,HMQC and HMBC,their chemicalstructures were determinated as glaucogenin-C 3-O-a-L-cymaropyranosyl-(1→4)-b-D-digitoxopyranosyl-(1→4)-β-D-canaropyranoside(1),stigmasterol(2)and ursolic acid(3).     

Synthesis,spectroscopic characterization and density functional studies of a bis-benzimidazole derivative and of its complexes with palladium(II) halides

The 2,6-bis(benzimidazol-2′-ylthiomethyl)pyridine (L) ligand and its palladium(II) complexes [Pd(L)X]X (X = Cl, Br, and I) have been synthesized and characterized by spectroscopic data acquisition. The ligand (L) was prepared by conventional heating as well as by microwave irradiation. Microwave irradiation shows additional features, including an easy workup, a much faster reaction and higher yields. The molar conductivity data reveal that the complexes form a 1:1 electrolyte in DMSO. The geometries, ground-state energetics and vibrational spectra of (L) and of its complexes have been elucidated, in terms of quantum chemical calculations. In the mononuclear complexes, the palladium atom is coordinated to three nitrogen atoms and one terminal halogen atom in a slightly distorted square planar arrangement. The present elemental analyses, FT–IR (mid, far), ¹H and ¹³C NMR spectra are in good accordance with the square planar geometry around the Pd ion. The thermal behaviors of the complexes have been assessed by thermal gravimetric and differential thermal analyses.     

The experimental and DFT studies of 1,3-dimethyl-2-[4-chloro-styryl]-benzimidazolium iodide

1,3-Dimethyl-2-[4-chloro-styryl]-benzimidazolium iodide (1) was synthesized and characterized by X-ray diffraction, ¹H NMR, MS, IR, UV–vis spectra and elemental analysis. The crystals are monoclinic, space group P2₁/c, with a = 12.507(3) Å, b = 7.3259(19) Å, c = 36.705(9) Å, V = 3358.9(15) Å³, and Z = 4 (at 296(2) K). Crystal stacking scheme indicates the face-to-face π?π aromatic stacking interactions. Molecular geometries, frequencies, IR, ¹H NMR and UV–vis were calculated at DFT/TD-DFT level using two hybrid exchange–correlation functionals, B3LYP and PBE1PBE. The stability of the molecule arising from hyperconjugative interaction and charge delocalization had been analyzed using natural bond orbital (NBO) analysis. These calculations on (1) provide deep insight into its electronic structure and properties.     

Synthesis and properties of 5,10,15,20-tetra(4-lauroylimidophenyl)porphyrin and its metal complexes

Transition metal complexes of 5,10,15,20-tetra(4-lauroylimidophenyl)porphyrin TLPPM [M = Mn(Cl), Fe(Cl), Co, Ni, Cu, Zn] have been synthesized and characterized by means of elemental analyses, UV–VIS spectra, infrared spectra, ¹H NMR spectra, molar conductance, differential scanning calorimetry (DSC), polarized optical microscopy (POM), cyclic voltammetry, luminescence spectra and surface photovoltage spectroscopies. The porphyrin ligand shows liquid crystalline behaviour, and it exhibits a high phase transition temperature 182 °C and a broad mesophase temperature span, 88 °C. The oxidation and reduction properties of the compounds were investigated by cyclic voltammetry. The photovoltaic properties and charge transfer process of the compounds were investigated by surface photovoltage spectroscopy (SPS) and electric field-induced surface photovoltage spectroscopic (EFISPS) techniques, which revealed that all the compounds are p-type semiconductors. Quantum yields of the S₁ → S₀ fluorescence were measured at room temperature. These studies will contribute to further choice and application of the liquid crystals.     

A novel fluorescence sensor for K+ based on bis-Bodipy: The ACQ effect controlled by cation complexation of pseudo crown ether ring

Three novel bis-Bodipy 3a–3c bridged with crown ether chain were prepared in yields of 70–78%. Their complexation absorption and fluorescent spectra for fourteen metal ions suggested that compound 3b exhibited the selective response for K⁺ with obvious ACQ effect. The association constant of compound 3b with K⁺ was 4.3 × 10⁵ M^?1 and 1:1 complex mode was deduced. The complexation mechanism of ACQ effect controlled by cation complexation of pseudo crown ether ring was confirmed by the fluorescent titrations, complexation FT-IR spectra, complexation ¹H NMR spectra, complexation ESI-MS spectra and contrast experiment of similar mono-Bodipy derivative. The K⁺ was binded in the cavity of a pseudo crown ether ring, leading to the closed distance for two Bodipy units and then enhancing the ACQ effect obviously. Both the structure of the crown ether chain and two Bodipy units were decisive factors for the selective fluorescence sensor for K⁺.     

Heating and temperature gradients of lipid bilayer samples induced by RF irradiation in MAS solid‐state NMR experiments

The MAS solid‐state NMR has been a powerful technique for studying membrane proteins within the native‐like lipid bilayer environment. In general, RF irradiation in MAS NMR experiments can heat and potentially destroy expensive membrane protein samples. However, under practical MAS NMR experimental conditions, detailed characterization of RF heating effect of lipid bilayer samples is still lacking. Herein, using ¹H chemical shift of water for temperature calibration, we systematically study the dependence of RF heating on hydration levels and salt concentrations of three lipids in MAS NMR experiments. Under practical ¹H decoupling conditions used in biological MAS NMR experiments, three lipids show different dependence of RF heating on hydration levels as well as salt concentrations, which are closely associated with the properties of lipids. The maximum temperature elevation of about 10 °C is similar for the three lipids containing 200% hydration, which is much lower than that in static solid‐state NMR experiments. The RF heating due to salt is observed to be less than that due to hydration, with a maximum temperature elevation of less than 4 °C in the hydrated samples containing 120 mmol l^?1 of salt. Upon RF irradiation, the temperature gradient across the sample is observed to be greatly increased up to 20 °C, as demonstrated by the remarkable broadening of ¹H signal of water. Based on detailed characterization of RF heating effect, we demonstrate that RF heating and temperature gradient can be significantly reduced by decreasing the hydration levels of lipid bilayer samples from 200% to 30%. Copyright © 2016 John Wiley & Sons, Ltd.     

One-pot multicomponent synthesis hexahydroquinoline derivatives in Triton X-100 aqueous micellar media

A facile and efficient synthesis of hexahydroquinoline derivatives (5a–o) was reported via a four-component condensation reaction of aldehydes, dimedone, methyl aceto acetate and ammonium acetate in the presence of Triton X-100 in water at room temperature. The use of just 20 mol % of Triton X-100 in water solvent is sufficient. The FT-IR, ¹⁹F NMR, ¹H NMR, ¹³C NMR spectra and elemental analysis confirm the structure of the compounds.     

Analysis of radiation induced degradation in FPC-461 fluoropolymers by variable temperature multinuclear NMR

Solid state nuclear magnetic resonance techniques have been used to investigate aging mechanisms in a vinyl chloride:chlorotrifluoroethylene copolymer, FPC-461, due to exposure to γ-radiation. Solid state ¹H MAS NMR spectra revealed structural changes in the polymer upon irradiation under both air and nitrogen atmospheres. Considerable degradation is seen with ¹H NMR in the vinyl chloride region of the polymer, particularly in the samples irradiated in air. ¹⁹F MAS NMR was used to investigate speciation in the chlorotrifluoroethylene blocks, though negligible changes were seen. ¹H and ¹⁹F NMR at elevated temperature revealed increased segmental mobility and decreased structural heterogeneity within the polymer, yielding significant resolution enhancement over room temperature solid state detection. The effects of multi-site exchange are manifested in both the ¹H and ¹⁹F NMR spectra as a line broadening and change in peak position as a function of temperature.     

An efficient and facile procedure for synthesis of octyl polyglucoside

Nonionic surfactant alkyl polyglucoside (APG) was prepared by direct glycosidation of alkyl alcohol with glucose in the presence of sulfate acid-silica gel (H_2SO_4/SiO_2) as solid acidic catalyst.The quantity of catalyst was only of 1 wt%,based on the glucose,and the conversion of glucose was close to 100% at 110℃in 1.5h.The product was characterized by FT-IR,mass and ~1H NMR spectra.The degree of polymerization (DP) of the glucose in the product was 1.37,and critical micelle concentration (CMC) of product was only 0.0104 wt%.