Lithium–manganese–nickel-oxide electrodes with integrated layered–spinel structures for lithium batteries

A series of lithium–manganese–nickel-oxide compositions that can be represented in three-component notation, xLi[Mn_1.5Ni_0.5]O₄ · (1 − x){Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂}, in which a spinel component, Li[Mn_1.5Ni_0.5]O₄, and two layered components, Li₂MnO₃ and Li(Mn_0.5Ni_0.5)O₂, are structurally integrated in a highly complex manner, have been evaluated as electrodes in lithium cells for x = 1, 0.75, 0.50, 0.25 and 0. In this series of compounds, which is defined by the Li[Mn_1.5Ni_0.5]O₄–{Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂} tie-line in the Li[Mn_1.5Ni_0.5]O₄–Li₂MnO₃–Li(Mn_0.5Ni_0.5)O₂ phase diagram, the Mn:Ni ratio in the spinel and the combined layered Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ components is always 3:1. Powder X-ray diffraction patterns of the end members and the electrochemical profiles of cells with these electrodes are consistent with those expected for the spinel Li[Mn_1.5Ni_0.5]O₄ (x = 1) and for ‘composite’ Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ layered electrode structures (x = 0). Electrodes with intermediate values of x exhibit both spinel and layered character and yield extremely high capacities, reaching more than 250 mA h/g with good cycling stability between 2.0 V and 4.95 V vs. Li° at a current rate of 0.1 mA/cm².     

Comments on stabilizing layered manganese oxide electrodes for Li batteries

An electrochemical study of structurally-integrated xLi₂MnO₃•(1 −x)LiMn_0.5Ni_0.5O₂ ‘composite’ materials has been undertaken to investigate the stability of electrochemically-activated electrodes at the Li₂MnO₃-rich end of the Li₂MnO₃–LiMn_0.5Ni_0.5O₂ tie-line, i.e., for 0.7 ≤ x ≤ 0.95. Excellent performance was observed for x = 0.7 in lithium half-cells; comparable to activated electrodes that have significantly lower values of x and are traditionally the preferred materials of choice. Electrodes with higher manganese content (x ≥ 0.8) showed significantly reduced performance. Implications for stabilizing low-cost, manganese-rich, layered lithium-metal-oxide electrode materials are discussed.     

PVP-Assisted ZrO2 coating on LiMn2O4 spinel cathode nanoparticles prepared by MnO2 nanowire templates

LiMn₂O₄ spinel nanorods prepared from nanowire MnO₂ templates were capped with polyvinyl pyrrolidone (PVP) and coated with ZrC₂O₄ precursors in aqueous solution. Upon annealing at 600 °C in air, an amorphous ZrO₂ nanoscale coating layer was obtained on the spinel nanoparticles with a particle size of <100 nm that formed from the splitting of the original spinel nanorods. The electrochemical cycling results clearly showed that nanoscale ZrO₂ coating significantly improved the rate capability and cycle life at 65 °C in spite of very high surface area of the spinel nanoparticles.     

Layered xLiMO2·(1−x)Li2M′O3 electrodes for lithium batteries: a study of 0.95LiMn0.5Ni0.5O2·0.05Li2TiO3

The electrochemical properties of 0.95LiMn_0.5Ni_0.5O₂·0.05Li₂TiO₃ have been investigated as part of a study of xLiMO₂·(1−x)Li₂M^′O₃ electrode systems for lithium batteries in which M=Co, Ni, Mn and M^′=Ti, Zr, Mn. The data indicate that the electrochemically inactive Li₂TiO₃ component contributes to the stabilization of LiMn_0.5Ni_0.5O₂ electrodes, which improves the coulombic efficiency of Li/xLiMn_0.5Ni_0.5O₂·(1−x)Li₂TiO₃ cells for x<1. The 0.95LiMn_0.5Ni_0.5O₂·0.05Li₂TiO₃ electrodes provide a rechargeable capacity of approximately 175 mAh/g at 50 °C when cycled between 4.6 and 2.5 V; there is no indication of spinel formation during electrochemical cycling.     

Li(4−x)/3Ti(5−2x)/3CrxO4 (0 ≤ x ≤ 0.9) spinels: New negatives for lithium batteries

Members of the spinel solid solution between Li_4/3Ti_5/3O₄ and LiCrTiO₄, i.e., Li_(4−x)/3Ti_(5−2x)/3Cr_xO₄ (0 ≤ x ≤ 0.9), have been investigated as possible negative electrodes for future lithium-ion batteries. Electrochemical behaviour have been studied over the potential range 1–3.5 V vs Li⁺/Li. Results are promising with anodic capacities between 129 and 163 mA h/g with a flat operating voltage at about 1.5 V, which is attributed to the pair Ti⁴⁺/Ti³⁺. The inclusion of Cr³⁺ in the spinel structure enhances the specific capacity. In-situ X-ray diffraction experiments confirm that the reaction proceeds in a topotactic manner.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

Study on the effect of Li doping in spinel Li4+xTi5−xO12 (0 ⩽ x ⩽ 0.2) materials for lithium-ion batteries

The effect of Li doping in spinel Li_4+xTi_5−xO₁₂ (0 ⩽ x ⩽ 0.2) materials on the structural and electrochemical properties were investigated. The ratio of the capacity in the voltage plateau (1.5 V) to the overall discharge capacity for Li_4.1Ti_4.9O₁₂ (x = 0.1) and Li_4.2Ti_4.8O₁₂ (x = 0.2) were higher than that of Li₄Ti₅O₁₂ especially at high current rates due to their enhanced lithium-ion and electronic conductivity by the substitution of Ti atoms by Li atoms. With the increasing of Li doping amount, lithium-ion and electronic conductivity of Li_4+xTi_5−xO₁₂ increased, however its cycling stability was depressed when the Li doping was of x = 0.2. The Li doping of x = 0.1, the appropriate Li doping amount, showed improved rate capability and better high rate performance comparing to undoped Li_4+xTi_5−xO₁₂ (x = 0).     

High-energy and high-power Li-rich nickel manganese oxide electrode materials

A lithium-rich nickel-manganese oxide compound Li_x(Ni_0.25Mn_0.75)O_y (x > 1) was synthesized from layered Na_0.9Li_0.3Ni_0.25Mn_0.75O_δ precursor using a lithium ion-exchange reaction. The electrochemical behavior of the material as a cathode for lithium batteries, and a preliminary discussion of its structure are reported. The product Li_1.32Na_0.02Ni_0.25Mn_0.75O_y (IE-LNMO) shows broad X-ray diffraction peaks, but possesses a high intensity sharp (003) layering peak and multiple peaks with intensity in the 20–23° 2θ region which suggest Ni–Mn ordering in the transition metal layer (TM). Li/IE-LNMO cells demonstrate very stable reversible capacities of 220 mAh/g @ 15 mA/g and possess extremely high power of 150 mAh/g @ 1500 mA/g (15C). The Li/IE-LNMO cell dQ/dV plot exhibits three reversible electrochemical processes due to Ni/Mn redox behavior in a layered component, and Mn redox exchange in a spinel component. No alteration in the dQ/dV curves and no detectable change in the voltage profiles over 40 cycles were observed, thus indicating a stable structure for lithium insertion/extraction. This new material is attractive for demanding Li-ion battery applications.     

Comparison of the electrochemical properties of metallic layered nitrides containing cobalt,nickel and copper in the 1 V–0.02 V potential range

We report the first example of an intercalation compound based on the nitrogen framework in which lithium can be intercalated and deintercalated. A comparison of the structural and electrochemical properties of the ternary lithium cobalt, nickel and copper nitrides is performed. Vacancy layered structures of ternary lithium nitridocobaltates Li_3−2xCo_xN and nitridonickelates Li_3−2xNi_xN with 0.10 ⩽ x ⩽ 0.44 and 0.20 ⩽ x ⩽ 0.60, respectively, are proved to reversibly intercalate Li ions in the 1 V–0.02 V potential range. These host lattices can accommodate up to 0.35 Li ion par mole of nitride. Results herein obtained support Li insertion in vacancies located in Li₂N⁻ layers while interlayer divalent cobalt and nickel cations are reduced to monovalent species. No structural strain is induced by the insertion–extraction electrochemical reaction which explains the high stability of the capacity in both cases. For the Li_1.86Ni_0.57N compound, a stable faradaic yield of 0.30 F/mol, i.e. 130 mAh/g, is maintained at least for 100 cycles. Conversely, the ternary copper nitrides corresponding to the chemical composition Li_3−xCu_xN with 0.10 ⩽ x ⩽ 0.40 do not allow the insertion reaction to take place due to the presence of monovalent copper combined with the lack of vacancies to accommodate Li ions. In the latter case, the discharge of the lithium copper nitrides is not reversible.     

The role of Li2MO2 structures (M=metal ion) in the electrochemistry of (x)LiMn0.5Ni0.5O2·(1−x)Li2TiO3 electrodes for lithium-ion batteries

The electrochemical reactions of lithium with layered composite electrodes (x)LiMn_0.5Ni_0.5O₂·(1−x)Li₂TiO₃ were investigated at low voltages. The metal oxide 0.95LiMn_0.5Ni_0.5O₂·0.05Li₂TiO₃ (x=0.95) which can also be represented in layered notation as Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂, can react with one equivalent of lithium during an initial discharge from 3.2 to 1.4 V vs. Li⁰. The electrochemical reaction, which corresponds to a theoretical capacity of 286 mAh/g, is hypothesized to form Li₂(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂ that is isostructural with Li₂MnO₂ and Li₂NiO₂. Similar low-voltage electrochemical behavior is also observed with unsubstituted, standard LiMn_0.5Ni_0.5O₂ electrodes (x=1). In situ X-ray absorption spectroscopy (XAS) data of Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂ electrodes indicate that the low-voltage (<1.8 V) reaction is associated primarily with the reduction of Mn⁴⁺ to Mn²⁺. Symmetric rocking-chair cells with the configuration Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂/Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂ were tested. These electrodes provide a rechargeable capacity in excess of 300 mAh/g when charged and discharged over a 3.3 to −3.3 V range and show an insignificant capacity loss on the initial cycle. These findings have implications for combating the capacity-loss effects at graphite, metal–alloy, or intermetallic negative electrodes against lithium metal-oxide positive electrodes of conventional lithium-ion cells.     

Preparation of Mn-substituted LiFeO2: A solid solution of LiFeO2 and LixMnO2

A new type of LiFeO₂–Li_xMnO₂ solid solution was synthesized at 350 °C under argon flow by a solid-state reaction. The doped Mn ions in the LiMn_xFe_1−xO₂ (0<x⩽0.5) obtained at 150 °C were regarded as an impurity in the orthorhombic LiFeO₂ structure and failed to form a perfect substitution form due to the low synthesis temperature. However, the LiFeO₂–Li_xMnO₂ solid solutions with various Mn contents (Mn/(Fe + Mn)=0.1–0.5) were successfully obtained by calcination at 350 °C. Especially, the XRD pattern of the 50% Mn-substituted LiFeO₂ material was very similar to that of a lithiated Li_xMnO₂ compound. The Li/50% Mn-substituted LiFeO₂ cell exhibited not only a distinct increased voltage plateau in the 2.8 V region, but also an excellent cycling performance upto 50 cycles. We believe that this LiFeO₂–Li_xMnO₂ solid solution type compound has a unique electrochemical property in the cycling process.     

Nb2O5 nanobelts: A lithium intercalation host with large capacity and high rate capability

In this study, Nb₂O₅ nanobelts, with a ca. ∼15 nm in thickness, ca. ∼60 nm in width and several tens of mircrometers in length, have first been used as the electrode material for lithium intercalation over the potential window of 3.0–1.2 V (vs. Li⁺/Li). It delivers an initial intercalation capacity of 250 mA hg⁻¹ at 0.1 Ag⁻¹ current density, corresponding to x = 2.5 for L_xNb₂O₅, and can still keep relative stable and reaches as large as 180 mA hg⁻¹ after 50 cycles. Surprisingly, the electrodes composed of Nb₂O₅ nanobelts can work smoothly even at high current density of 10 Ag⁻¹, and shows higher specific capacity and excellent cycling stable, as well as sloped feature in voltage profile. Cycling test indicates Nb₂O₅ nanobelts electrode shows a high reversible charge/discharge capacity, high rate capability with excellent cycling stability.     

Electrochemical properties of Li(Li(1−x)/3CoxMn(2−2x)/3)O2 (0 ⩽ x ⩽ 1) solid solutions prepared by poly-vinyl alcohol (PVA) method

The whole range of solid solutions Li(Li_(1−x)/3Co_xMn_(2−2x)/3)O₂ (0 ⩽ x ⩽ 1) was firstly synthesized by an aqueous solution method using poly-vinyl alcohol as a synthetic agent to investigate their structure and electrochemical properties. X-ray diffraction results indicated that the synthesized solid solutions showed a single phase without any detectable impurity phase and have a hexagonal structure with some additional peaks caused by monoclinic distortion, especially in the solid solutions with a low Co amount. In the electrochemical examination, the solid solutions in the range between 0.2 ⩽ x ⩽ 0.9 showed higher discharge capacity and better cyclability than LiCoO₂ (x = 1) on cycling between 2.0 and 4.6 V with 100 mA g⁻¹ at 25 °C. For example, Li(Li_0.2Co_0.4Mn_0.4)O₂ (x = 0.4) exhibited a high discharge capacity of 180 mA h g⁻¹ at the 50th cycle. By synthesizing the solid solution between Li₂MnO₃ and LiCoO₂, the electrochemical properties of the end members were improved.     

Sulfone-based electrolytes for high-voltage Li-ion batteries

Sulfone-based electrolytes have been investigated as electrolytes for lithium-ion cells using high-voltage positive electrodes, such as LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ spinels, and Li₄Ti₅O₁₂ spinel as negative electrode. In the presence of imide salt (LiTFSI) and ethyl methyl sulfone or tetramethyl sulfone (TMS) electrolytes, the Li₄Ti₅O₁₂/LiMn₂O₄ cell exhibited a specific capacity of 80 mAh g^?1 with an excellent capacity retention after 100 cycles. In a cell with high-voltage LiNi_0.5Mn_1.5O₄ positive electrode and 1 M LiPF₆ in TMS as electrolyte, the capacity reached 110 mAh g^?1 at the C/12 rate. When TMS was blended with ethyl methyl carbonate, the Li₄Ti₅O₁₂/LiNi_0.5Mn_1.5O₄ cell delivered an initial capacity of 80 mAh g^?1 and cycled fairly well for 1000 cycles under 2C rate. The exceptional electrochemical stability of the sulfone electrolytes and their compatibility with the Li₄Ti₅O₁₂ safer and stable anode were the main reason behind the outstanding electrochemical performance observed with high-potential spinel cathode materials. These electrolytes could be promising alternative electrolytes for high-energy density battery applications such as plug-in hybrid and electric vehicles that require a long cycle life.     

Synthesis and electrochemical characteristics of xLi2MnO3–(1−x)Li(Mn0.375Ni0.375Co0.25)O2 (0.0 ≤ x ≤ 1.0) thin film cathode for lithium rechargeable micro batteries

We have compared the structure, microstructure, and electrochemical characteristics of xLi₂MnO₃–(1−x)Li(Mn_0.375Ni_0.375Co_0.25)O₂ (0.0 ≤ x ≤ 1.0) thin films with their bulk cathode laminate counterparts of identical compositions. Pure Li(Mn_0.375Ni_0.375Co_0.25)O₂ as well as the synthesized composite films partially transform into cubic spinel structure during charge–discharge cycling. In contrast, such layered to spinel phase transformation has only been identified in bulk cathode laminates with x ≥ 0.75. At a current density 0.05 mAcm⁻², the discharge capacity of Li(Mn_0.375Ni_0.375Co_0.25)O₂ thin film was measured to be ∼60 μAhcm⁻². The discharge capacity (∼217 μAhcm⁻²) was markedly improved in x∼0.5 composite thin film. The capacity retention after 20 charge discharge cycles are improved in composite films; however, their capacity fading could not be eliminated completely.     

High capacity Li[Li0.2Mn0.54Ni0.13Co0.13]O2–V2O5 composite cathodes with low irreversible capacity loss for lithium ion batteries

With an aim to suppress the huge irreversible capacity loss encountered in high capacity layered oxide solid solutions between Li₂MnO₃ and LiMO₂ (M = Mn, Ni, and Co), layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with various V₂O₅ contents have been investigated. The irreversible capacity loss decreases from 68 mAh/g at 100% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ to 0 mAh/g around 89 wt.% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–11 wt.% V₂O₅ as the lithium-free V₂O₅ serves as an insertion host to accommodate the lithium ions that could not be inserted back into the layered lattice after the first charge. The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with about 10–12 wt.% V₂O₅ exhibit an attractive discharge capacity of close to 300 mAh/g with little irreversible capacity loss and good cyclability.     

Sol–gel fabrication of lithium-ion microarray battery

Microarray electrodes of LiMn₂O₄ and Li_4/3Ti_5/3O₄ were prepared on a glass substrate using a sol–gel method. The prepared LiMn₂O₄ and Li_4/3Ti_5/3O₄ microarray electrodes were characterized with scanning electron microscopy, Raman spectroscopy, and cyclic voltammetry. Using a polymer-gel electrolyte, lithium ion microbattery of Li_4/3Ti_5/3O₄/polymer-gel/LiMn₂O₄ (cell area: 6.6 × 10⁻² cm²) was successfully constructed. The microbattery operated reversibly at 2.5 V, and the discharge capacity was 300 nA h, which corresponded to an energy density of 11 μW h cm⁻².     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

Formation of nano-crystalline quartz crystals from ZnO/MgO/Al2O3/TiO2/ZrO2/SiO2 glasses

Glasses with the compositions 50.9 SiO₂ · 20.8 Al₂O₃ · (20.8 ? x) MgO· × ZnO · 3.7 TiO₂ · 3.7 ZrO₂ with x = 0, 2.3, 4.6 and 9.3 were annealed at temperatures in the range from 850 to 1100 °C. Depending on temperature, high- or low-quartz solid solutions, magnesium aluminosilicate, mullit and spinel precipitated. These glass–ceramics exhibit excellent mechanical properties and are potential candidates for applications in micromechanics or as hard disc substrate.The larger the ZnO concentration, the lower is the glass transition temperature. Also microhardnesses and Young’s moduli increased with increasing ZnO concentration. The nucleation temperature was of minor importance. To achieve good mechanical properties, the initially formed high-quartz phase must transform to the corresponding low-quartz phase. This occurs if the quartz phase contains only minor MgO or ZnO concentrations, which can be achieved by increasing the annealing times or temperature. Then MgO, ZnO and Al₂O₃ occur as separate spinel or gahnite phase.     

Enhancing the rate capability of high capacity xLi2MnO3 · (1 − x)LiMO2 (M = Mn,Ni, Co) electrodes by Li–Ni–PO4 treatment

The rate capability of high capacity xLi₂MnO₃ · (1 ? x)LiMO₂ (M = Mn, Ni, Co) electrodes for lithium-ion batteries has been significantly enhanced by stabilizing the electrode surface by reaction with a Li–Ni–PO₄ solution, followed by a heat-treatment step. Reversible capacities of 250 mAh/g at a C/11 rate, 225 mAh/g at C/2 and 200 mAh/g at C/1 have been obtained from 0.5Li₂MnO₃ · 0.5LiNi_0.44Co_0.25Mn_0.31O₂ electrodes between 4.6 and 2.0 V. The data bode well for their implementation in batteries that meet the 40-mile range requirement for plug-in hybrid vehicles.