Structure of Conducting Polymer Films Prepared on the Surface and in the Pores of Poly(ethylene terephthalate) Track Membranes by Template Synthesis

The results of a structural study of conducting polymer coatings deposited onto poly(ethylene terephthalate) (PET) track membranes by template synthesis are reported. The following aspects of the quality of polymer coatings were studied: the ratio between film and granular polymers, the polymer distribution over the surface of track membranes, and the thickness of polymer layers on the opposite sides of track membranes. The fraction of granular polypyrrole (PPy) on the surface and in the pores of a film increased with pore diameter. A decrease in the polymerization temperature decreased the amount of granular PPy on the surface of membranes, whereas the effect of granular PPy on the water permeability of track membranes remained unchanged. A more homogeneous distribution of PPy over the surface of track membranes can be obtained by density equalization of reacting solutions; however, the fraction of granular PPy on the membrane surface increased in this case. It was found that polymer coatings on the two sides of the surface of a membrane template had different thicknesses. Poly(N-methylpyrrole) completely covered only one side of a track membrane facing a monomer solution.     

Controlled pore functionalization of poly(ethylene terephthalate) track-etched membranes via surface-initiated atom transfer radical polymerization

A new method for surface-initiated atom transfer radical polymerization (ATRP) on the technical polymer poly(ethylene terephthalate) (PET) has been developed which allows controlling and estimating the layer thickness of the grafted polymer in the isocylindrical pores of track-etched membranes. After PET surface treatment by oxidative hydrolysis, the bromoalkyl initiator was immobilized on the PET surface in a two-step solid-phase reaction; the isoporous membrane structure was preserved, and the pore diameter was increased from 760 to 790 nm. Poly(N-isopropylacrylamide) (PNIPAAm) was grafted under ATRP conditions from a methanol/water mixture at room temperature. Both monomer concentration and reaction time could be used as parameters to adjust the degree of grafting. Effective grafted layer thickness and its response to temperature were estimated from pure water permeability. All data, especially the high polymer densities (0.37 g/cm3) in the swollen layers at 25 degrees C, indicate that grafted PNIPAAm with a "brush" structure has been achieved. For dry PNIPAAm layer thicknesses on the PET pore walls of up to 80 nm, a temperature-induced swelling/deswelling ratio of approximately 3 had been observed. Reduction of the brush grafting density, via composition of the reaction mixture used in solid-phase synthesis for initiator immobilization, led to an increase of that swelling/deswelling ratio. Further, density and temperature response of the grafted PNIPAAm layers synthesized via ATRP were compared with those obtained in the same membranes by less controlled photografting, leading to lower grafting density and larger gradients in grafted layer density and, consequently, much higher swelling/deswelling ratios (>15).     

A study on the water permeability of poly(ethylene terephthalate) track membranes modified by dc discharge polymerization of <Emphasis Type="Italic">N,N</Emphasis>-dimethylaniline

The properties of poly(ethylene terephthalate) track membranes modified by dimethylaniline polymerization in a dc discharge were studied. The influence of plasma treatment conditions on the basic membrane characteristics: the pore size, wettability, surface charge, and water permeability, were examined. It was shown that the polymer membranes obtained were capable of reversibly responding to pH and pressure changes.Translated from Khimiya Vysokikh Energii, Vol. 39, No. 2, 2005, pp. 143–152.Original Russian Text Copyright © 2005 by Kravets, Gilman, Drachev.This revised version was published online in April 2005 with a corrected cover date.     

Poly(N-isopropylacrylamide) grafted into nanopores: Thermo-responsive behaviour in the presence of different salts

Surface initiated polymerization of N(isopropylacrylamide) (NIPAM) was performed by controlled radical polymerization on PET track-etched membranes presenting two different pore diameters (narrow pores: ∼80 nm and large pores: ∼330 nm). The opening and closing characteristics of the resulting PNIPAM-g-PET membranes were investigated by conductometric measurements carried out at different temperatures below and above the LCST of PNIPAM and in the presence of different salts. Depending on the membrane pore size, two types of permeation control mechanisms are observed. In large pore membranes, expanded PNIPAM chains conformations result in reduced effective pore size and therefore lower permeabilities relative to collapsed macromolecules chain conformations. In contrast, in narrow pore membranes, the expanded PNIPAM brush presents greater degrees of hydration in the surface layer and therefore gives rise to higher permeabilities than the collapsed conformation. In this situation, the overall permeability is thus comparable to that of a hydrogel membrane.     

Synthesis of bilayer composite nanomembranes with conductivity asymmetry

The structure and electrochemical properties of polyethylene terephthalate track membranes modified in acetylene plasma are studied. It is found that polymer deposition on the track membrane surface using acetylene polymerization in plasma results in the case of formation of a semipermeable layer covering pores in formation of a composite nanomembrane featuring asymmetry of conductivity in solutions of electrolytes: a rectifying effect similar to that of a p-n junction in semiconductors. It is shown that the observed effect of conductivity asymmetry is caused by a significant decrease in the diameter of pores in the plasma-deposited polymer layer and a change in the pore geometry, same as existence of an interface between the initial membrane and polymer layer that have a different concentration of carboxyl groups in the surface layer. The impedance spectroscopy method allowed obtaining information on ion transfer in the studied membranes.     

Improvement of pore geometry and performances of poly(ethylene terephthalate) track membranes by a protective layer method using plasma-induced graft polymerization of 1H,1H,2H-perfluoro-1-octene monomer

The process of geometrical modification of pores in poly(ethylene terephthalate) track-etched membranes (TM) by use of plasma deposition of a fluorine-containing polymer protective layer on one membrane surface and alkali etching of the other surface has been studied in order to produce membranes with improved performance characteristics. Samples of membranes with conical pores have been obtained which have better filtration efficiency compared with initial TM with cylindric pores. Plasma polymerization of 1H,1H,2H-perfluoro-1-octene at the membrane surface was used to produce the protective layer resistant to alkali solutions. The occurrence of plasma modification and changing of pore geometry have been verified by X-ray photoelectron spectroscopy and scanning electron microscopy studies. The filtration efficiency and selectivity of the modified membranes have been studied.     

钴离子配位分子印迹聚合物膜渗透特性的研究

采用分子印迹技术紫外光引发原位聚合的方法制备了带支撑膜的钴离子配位分子印迹聚合物膜. 用扫描电镜测定了膜的表面形貌. 通过膜渗透实验表明, 在一定浓度钴离子存在下, 印迹膜对模板分子表现出良好的渗透选择性. 分别考察了阳离子和阴离子对印迹膜渗透模板分子的影响. 本工作有助于分子印迹技术应用于传感器技术和连续分离技术的研究.     

Potentiometric sensors for Ag+ based on poly(3-octylthiophene) (POT)

Potentiometric ion sensors were prepared from the conjugated polymer poly(3-octylthiopene) (POT). The influence of additional membrane components, including silver 7,8,9,10,11,12-hexabromocarborane (AgCB₁₁H₆Br₆) and potassium tetrakis[3,5-bis(trifluoromethyl)phenyl]borate (KTpFPB) as lipophilic salts, and [2.2.2]p,p,p-cyclophane as silver ionophore, was studied. The membrane components were dissolved in chloroform and membranes were prepared by solution casting on glassy carbon disk electrodes. For comparison, POT-based potentiometric sensors were also prepared by galvanostatic electrosynthesis of POT from the 3-octylthiophene monomer. All the POT-based ion sensors fabricated by solution casting show Nernstian or slightly sub-Nernstian response to Ag⁺, even those based only on POT without any additional membrane components. The potentiometric response of electrochemically polymerized POT depends on the film thickness and the doping anion incorporated in the conducting polymer during polymerization. It is of particular importance that chemically synthesized undoped POT (without any additives) shows a sensitive and selective potentiometric response to Ag⁺ ions although UV-vis results show that POT remains in its undoped form, i.e., POT is not oxidized by Ag⁺. This indicates that undoped POT can exhibit good sensitivity and selectivity to Ag⁺ also in the absence of metallic silver in the polymer film. In this case, the potentiometric response is related to interactions between Ag⁺ and the conjugated polymer backbone. Presented at the 4th Baltic Conference on Electrochemistry, Greifswald, 13–16, 2005     

SEM研究PET核孔膜的光接枝聚合

以PET核孔膜为基材 ,二苯甲酮为引发剂 ,采用光接枝方法实现了丙烯酸和丙烯酰胺在核孔膜上的接枝 ,用扫描电镜 (SEM)直接观察了接枝前后膜的表面形貌 ,考察了不同因素对于接枝位置和接枝效果的影响 .发现膜材料本身特性和接枝反应条件对接枝位置和接枝效果有较大影响 .通过光接枝能够实现膜孔的封盖、缩小、填堵等不同的效果 .采用正侧涂布法反应 ,标准直孔 ,特别是小孔径膜 (0 4 μm) ,不利于孔内的接枝 ,接枝主要在膜的表面 ,从而产生孔封盖效应 .双锥形的非标准直孔 ,由于孔壁的受光性好 ,容易发生孔壁上的接枝从而被填充 .大孔径的膜 (5 μm) ,需要加入交联剂才能在孔壁上形成厚的接枝层 .提出了一种新的反应方法 背侧吸附法 ,反应液依靠毛细作用由膜的底部吸入膜孔 ,膜的向光侧表面不存在反应液 ,接枝只发生在膜孔内 ,从而得到很好的填孔效果 .     

POROUS MEMBRANE TEMPLATED SYNTHESIS OF POLYMER PILLARED LAYER

The anodic porous alumina membranes with a definite pore diameter and aspect ratio were used as templates tosynthesize polymer pillared layer structures. The pillared polymer was produced in the template membrane pores, and thelayer on the template surfaces. Rigid cured epoxy resin, polystyrene and soft hydrogel were chosen to confirm themethodology. The pillars were in the form of either tubes or fibers, which were controlled by the alumina membrane pore surface wettability. The structural features were confirmed by scanning electron microscopy results.     

Trapping and release of cargo molecules from a micro-stamped mesoporous thin film controlled by poly(NIPAAm-co-AAm)

Materials that utilize the micropatterned structure of a mesoporous silica film to successfully load and release cargo using a thermal sensitive polymer are presented in this paper. Films with pore sizes of ~2 and ~5 nm aligned in the pulling direction were synthesized using evaporation induced self-assembly techniques. The pores are exposed using a new method of stamping micropatterns without the use hydrofluoric acid. A well studied temperature dependent polymer [poly(N-isopropylacrylamide-co-acrylamide)] was grafted onto the surface of these films to act as a temperature activated gatekeeper. Below the lower critical solution temperature (LCST) the polymer is erect and can block the pore openings, trapping cargo inside the pores. When the temperature is above the LCST the polymer collapses and unblocks the pores, allowing cargo to escape. The loading capacities as well as the reusability of these films were studied.     

Microscopic observation of the crystalline form of poly(<Emphasis Type="Italic">o</Emphasis>-methoxyaniline) on a membrane electrode

We describe electrochemical and microscopic (SEM) studies on the electrochemical polymerization of poly(o-methoxyaniline). The crystalline form of the polymer was obtained. The poly(o-methoxyaniline) crystals are formed on a membrane electrode from an acidic solution of the monomer. It is suggested that the pores of the membrane work as nuclear crystallization points.Contribution to the 3rd Baltic Conference on Electrochemistry, Gdansk-Sobieszewo, Poland, 23–26 April 2003Dedicated to the memory of Harry B. Mark, Jr. (28 February 1934–3 March 2003)     

Permeability and electrokinetic characterization of poly(ethylene terephthalate) capillary pore membranes with grafted temperature-responsive polymers

Poly(ethylene terephthalate) (PET) track-etched membranes with average pore diameters of 692 and 1629 nm were functionalized using the monomer N-isopropylacrylamide (NIPAAm) and a photoinitiated "grafting-from" approach in which a surface-selective reaction has been most efficiently achieved by combinations of the unmodified PET surface with benzophenone and, alternatively, of an aminated PET surface with benzophenone carboxylic acid. Consistent estimations of the pore diameters of the base PET membranes and of the effective grafted polyNIPAAm layer thicknesses on the PET pore walls were possible only on the basis of the permeabilities measured with aqueous solutions of higher ionic strength (e.g., 0.1 M NaCl). However, the permeabilities measured with ultrapure water indicated that the "electroviscous effect" was significant for both base membranes. The influences of membrane pore diameter, surface charge, and solution ionic strength could be interpreted in the framework of the space-charge model. Functionalized membranes with collapsed grafted polymer hydrogel layer thicknesses of a few nanometers exhibited almost zero values of the zeta potential estimated from the trans-membrane streaming potential measurements. This was caused by a "hydrodynamic screening" of surface charge by the neutral hydrogel. Very pronounced changes in permeability as a function of temperature were measured for PET membranes with grafted polyNIPAAm layers, and the effective layer thickness in the swollen state--here up to approximately 300 nm--correlated well with the degree of functionalization. The subtle additional effects of solution ionic strength on the hydrodynamic layer thickness at 25 degrees C were different from the effects for the base PET membranes and could be explained by a variation in the degree of swelling, resembling a "salting-out" effect. Overall, it had been demonstrated that the functionalized capillary pore membranes are well suited for a detailed and quantitative evaluation of the relationships between the synthesis, the structure, and the function of grafted stimuli-responsive polymer layers.     

Temperature-controlled flow switching in nanocapillary array membranes mediated by poly(N-isopropylacrylamide) polymer brushes grafted by atom transfer radical polymerization

We report actively controlled transport that is thermally switchable and size-selective in a nanocapillary array membrane (NCAM) prepared by grafting poly(N-isopropylacrylamide) (PNIPAAm) brushes onto the exterior surface of a Au-coated polycarbonate track-etched membrane. A smooth Au layer on the membrane surface, which is key to obtaining a uniform polymer film, was prepared by thermal evaporation of approximately 50 nm Au on both exterior surfaces. After evaporation, the inner diameter of the pore is reduced slightly, but the NCAM retains a narrow pore size distribution. PNIPPAm brushes with 10-30 nm (dry film) thickness were grafted onto the Au surface through surface-initiated atom transfer radical polymerization (ATRP) using a disulfide initiator, (BrC(CH3)2COO(CH2)11S)2. Molecular transport through the PNIPAAm polymer brush-modified NCAMs was investigated by real-time fluorescence measurements using fluorescein isothiocyanate (FITC)-labeled dextrans ranging from 4.4 to 282 kDa in membranes with variable initial pore diameters (80, 100, and 200 nm) and different PNIPAAm thicknesses. Manipulating the temperature of the NCAM through the PNIPAAm lower critical solution temperature (LCST) causes large, size-dependent changes in the transport rates. Over specific ranges of probe size, transport is completely blocked below the LCST but strongly allowed above the LCST. The combination of the highly uniform PNIPAAm brush and the monodisperse pore size distribution is critical in producing highly reproducible switching behavior. Furthermore, the reversible nature of the switching raises the possibility of using them as actively controlled filtration devices.     

Template synthesis of polyaniline and poly(2-methoxyaniline) nanotubes: comparison of the formation mechanisms

The process of polyaniline (PANI), poly(2-methoxyaniline) (POMA) nanotubes formation was investigated. Polyaniline and poly(2-methoxyaniline) nanotubes were prepared by chemical in situ deposition within the pores of polycarbonate membranes. It was found that the formation of polyaniline and poly(2-methoxyaniline) proceeds by two substantially different mechanisms. In the case of PANI, the polymer is first formed in the polymerization solution (the solution containing the monomer and oxidant, where the polycarbonate substrate is placed), and then it precipitates on/into the membrane. In the case of POMA, the oxidized 2-methoxyaniline molecules are first adsorbed on polycarbonate surface, and then, as a consequence of their accumulation, they recombine to form the polymer.     

Plasma-induced graft copolymerization of poly(methacrylic acid) on electrospun poly(vinylidene fluoride) nanofiber membrane

Electrospun nanofibrous membranes (ENM) which have a porous structure have a huge potential for various liquid filtration applications. In this paper, we explore the viability of using plasma-induced graft copolymerization to reduce the pore sizes of ENMs. Poly(vinylidene) fluoride (PVDF) was electrospun to produce a nonwoven membrane, comprised of nanofibers with diameters in the range of 200-600 nm. The surface of the ENM was exposed to argon plasma and subsequently graft-copolymerized with methacrylic acid. The effect of plasma exposure time on grafting was studied for both the ENM and a commercial hydrophobic PVDF (HVHP) membrane. The grafting density was quantitatively measured with toluidine blue-O. The degree of grafting increased steeply with an increase in plasma exposure time for the ENM, attaining a maximum of 180 nmol/mg after 120 s of plasma treatment. However, the increase in the grafting density on the surface of the HVHP membrane was not as drastic, reaching a plateau of 65 nmol/mg after 60 s. The liquid entry permeation of water dropped extensively for both membranes, indicating a change in surface properties. Field emission scanning electron microscopy micrographs revealed an alteration in the surface pore structure for both membranes after grafting. Bubble point measurements of the ENM reduced from 3.6 to 0.9 um after grafting. The pore-size distribution obtained using the capillary flow porometer for the grafted ENM revealed that it had a similar profile to that of a commercial hydrophilic commercial PVDF (HVLP) membrane. More significantly, water filtration studies revealed that the grafted ENM had a better flux throughput than the HVLP membrane. This suggests that ENMs can be successfully engineered through surface modification to achieve smaller pores while retaining their high flux performance.     

微乳液聚合耦合共混法构建聚偏氟乙烯共混杂化膜

以苯乙烯和甲基丙烯酸甲酯混合物作为油相, 采用反相微乳液法制备了AgCl纳米粒子; 通过微乳液原位聚合油相单体得到包含AgCl纳米粒子的聚合乳液; 将聚合乳液与聚偏氟乙烯(PVDF)通过共混法构建了包含AgCl纳米粒子的PVDF共混杂化膜. 紫外-可见光谱、 透射电子显微镜(TEM)及扫描电子显微镜(SEM)等表征结果和超滤实验结果表明, 聚合乳液加入的同时引入了亲水性聚合物和表面亲水的AgCl纳米粒子, 不仅改善了PVDF共混杂化膜的孔隙率和平均孔径, 还显著增强了PVDF共混杂化膜的极性和亲水性, 最终提升了膜的水通量和抗污染性能; 过量聚合乳液加入后不能与PVDF材料均匀共混, 而且AgCl纳米粒子也会在膜中形成团聚物堵塞膜孔隙, 从而削弱了膜的水通量和抗污染性能.     

热致相分离法偏二氯乙烯-氯乙烯共聚物多孔膜的制备及性能

以偏二氯乙烯-氯乙烯共聚物[P(VDC-co-VC)]为成膜聚合物, 邻苯二甲酸二甲酯(DMP)为稀释剂, 采用热致相分离(TIPS)法制备了具有多孔结构的P(VDC-co-VC)膜. 通过聚合物-稀释剂二元体系相图、 场发射扫描电镜(FESEM)、 差示扫描量热仪(DSC)、 X射线衍射(XRD)、 原子力显微镜(AFM)、 纯水通量、 接触角、 孔径及其分布、 截留率及力学性能等研究了聚合物含量对P(VDC-co-VC)多孔膜结构和性能的影响. 结果表明, P(VDC-co-VC)-DMP二元体系成膜过程以液-液(L-L)分相为主, 随着聚合物含量增加, 膜的横截面由类花瓣状结构向胞腔状结构转变, 膜的孔连通性降低, 结构变得较为致密, 同时膜上表面孔隙率降低, 粗糙度增大. L-L分相时间和聚合物含量的变化, 导致膜结晶度先降低后增大. 聚合物含量的增加使膜上表面接触角、 断裂强度及蛋白截留率增加, 但膜的平均孔径、 孔隙率及纯水通量先增加后减小. 当聚合物质量分数为30%时, 所得膜通透性较优, 断裂强度可达7.5 MPa.     

Supported particle track etched polyimide membranes: a grazing incidence small-angle X-ray scattering study

Particle track etched polyimide membranes on silicon substrates covered with a native oxide layer are investigated. Preparation steps similar to the common classical particle track etched membrane production, giving rise to free-standing membranes, are successfully applied to the supported membranes. Polyimide films are used as a starting material for a template preparation based on high energy ion irradiation. The film/membrane structure is probed at different length scales by grazing incidence small-angle X-ray scattering at each individual preparation step. In addition, characterization with atomic force microscopy, variable-angle spectroscopic ellipsometry, Fourier transform infrared transmission, and attenuated total reflection spectroscopy is performed. An amount of 6 +/- 1 vol % pores inside the polyimide film is detected. The pores are oriented perpendicular to the substrate surface and have a conical shape, yielding a slightly reduced pore size at the substrate/film interface.     

Synthesis and Morphology of poly(N-isopropylacrylamide) Nanocomposites with Emulsion Templated Nanoporous Structure

In this study, poly(N-isopropylacrylamide) (PNIPAAM) hydrogels were synthesized via a liquid template polymerization method using 200–400 nm polydimethylsiloxane (PDMS) droplets as the porogens, which were stabilized by sodium dodecyl sulfate (SDS). Similar hydrogels were also synthesized with iron (III) oxide superparamagnetic nanoparticles embedded within the gel. These gels were subjected to freeze- or air-drying, and then imaged using scanning electron microscopy. It was found that pores were not accessible from the surface of the freeze-dried gels, but were visible on the surface parallel to the crack plane within the polymer. In contrast, air-dried gels exhibited a well-defined nanoporous structure on the surface. The iron oxide nanoparticles did not have a significant effect on the hydrogel morphology.