Amperometric determination of the insecticide fipronil using batch injection analysis: comparison between unmodified and carbon-nanotube-modified electrodes

The electrochemical oxidation of fipronil is investigated on unmodified and multi-walled carbon-nanotube (MWCNT)-modified glassy carbon electrodes (GCEs), and its amperometric determination using batch injection analysis (BIA) is demonstrated. An oxidation peak was observed at 1.5 V in a 0.1 mol L^?1 HClO₄/acetone solution (50:50, v/v) on both surfaces. Although MWCNT-modified GCE provided greater sensitivity, the unmodified GCE showed low RSD value, wider linear range, and reduced adsorption of fipronil or its oxidized products on the electrode surface. A detection limit of 4.7 μmol L^?1 and linear range of 25–300 μmol L^?1 were obtained using a bare GCE. The method was applied in veterinary formulations with results in agreement with those obtained by high-performance liquid chromatography.     

A Simple Method for Determination of Homologue Imidazolium Cations in Ionic Liquids Using IC with Direct Conductivity Detection

An investigation was carried out into the fast determination of five homologue imidazolium cations in ionic liquids by ion chromatography using a cation-exchange column and direct conductivity detection. Ethylenediamine, complex organic acid (citric acid, oxalic acid and tartaric acid) and organic modifiers (acetonitrile) were used as mobile phase. The influences of the eluent types, eluent concentration, eluent pH and column temperature on separation of the cations were discussed. Simultaneous separation and determination of the five homologue imidazolium cations in ionic liquids were achieved under an optimum condition. The optimized mobile phase was consisted of 0.25 mmol L^?1 ethylenediamine + 0.5 mmol L^?1 citric acid + 3% acetonitrile (v/v) (pH 4.1), set at a flow rate of 1.0 mL min^?1. The column temperature was 40 °C and detection limits were obtained in the range of 1.1–45.6 mg L^?1. The relative standard deviations of the chromatographic peak areas for the cations were <3.0% (n = 5). This method was successfully applied to separate imidazolium cations in ionic liquids produced by organic synthesis. The recoveries of spiked components were 92.5–101.9%.     

Glucose biosensor based on graphite electrodes modified with glucose oxidase and colloidal gold nanoparticles

The electrochemistry of glucose oxidase (GOx) immobilized on a graphite rod electrode modified by gold nanoparticles (Au-NPs) was studied. Two types of amperometric glucose sensors based on GOx immobilized and Au-NPs modified working electrode (Au-NPs/GOx/graphite and GOx/Au-NPs/graphite) were designed and tested in the presence and the absence of N-methylphenazonium methyl sulphate in different buffers. Results were compared to those obtained with similar electrodes not containing Au-NPs (GOx/graphite). This study shows that the application of Au-NPs increases the rate of mediated electron transfer. Major analytical characteristics of the amperometric biosensor based on GOx and 13 nm diameter Au-NPs were determined. The analytical signal was linearly related to glucose concentration in the range from 0.1 to 10 mmol L^?1. The detection limit for glucose was found within 0.1 mmol L^?1 and 0.08 mmol L^?1 and the relative standard deviation in the range of 0.1–100 mol L^?1 was 0.04–0.39%. The τ_1/2 of V _max characterizes the storage stability of sensors: this parameter for the developed GOx/graphite electrode was 49.3 days and for GOx/Au-NPs/graphite electrode was 19.5 days. The sensor might be suitable for determination of glucose in beverages and/or in food.     

Simultaneous Analysis of Sugars and Polyphenols in Tobacco by CZE with Amperometric Detection Based on a Cu2O/MWCNT-COOH Composite Electrode

A composite electrode was fabricated from Cu₂O powder, carboxyl-functionalized multi-wall carbon nanotubes (MWCNT-COOH), and paraffin oil in the proportions 51:17:32 (w/w). This composite electrode was used for amperometric detection (CZE–AD) in simultaneous capillary zone electrophoretic analysis of chlorogenic acid, rutin, sucrose, glucose, mannose, and fructose in tobacco samples. Under the optimum conditions, the six analytes could be separated in 100 mmol L^?1 NaOH buffer within 30 min. Good linearity was achieved in the range 1 × 10^?7–1 × 10^?4 mol L^?1 for the two polyphenols and 5 × 10^?6–1 × 10^?3 mol L^?1 for the four sugars. The detection limits (S/N = 3) for the polyphenols and sugars were as low as 10^?8 mol L^?1 and 10^?6 mol L^?1, respectively.     

Graphite-Polyurethane Composite Electrode as an Amperometric Flow Detector in the Determination of Atenolol

Abstract

A bare graphite-polyurethane composite was evaluated as an amperometric detector in the flow injection determination of atenolol in pharmaceutical formulations. Using a flow injection analysis (FIA) procedure, a linear analytical curve was observed in the 0.2–3.0 mmol L^?1 range with a minimum detectable net concentration limit of detection (LOD = 18.1 µmol L^?1 and 90 determinations h^?1. Interferences from propranolol and furosemide were observed but not from the other components of the tablet. Thus, it was possible to determine atenolol in tablets without interference and with results that agreed with high performance liquid chromatography (HPLC) procedure with a 95% confidence level in a fast and accurate procedure.     

Rapid Analysis of Nitrate and Nitrite by Ion-Interaction Chromatography on a Monolithic Column

Ion-interaction chromatography with direct conductivity detection has been used for analysis of nitrate and nitrite. Chromatographic separation was performed on a monolithic silica-based C₁₈ column dynamically modified with tetrabutylammonium (TBA⁺). Using the optimized mobile phase, containing 2.0 mmol L^?1 TBA⁺ and 0.8 mmol L^?1 citrate (pH 6.0), delivered at a flow rate of 6.0 mL min^?1, separation of five anions (chloride, nitrite, bromide, nitrate, and sulfate) was achieved in only 40 s at a column temperature of 30 °C. The detection limits for nitrate and nitrite were 0.74 and 0.92 mg L^?1, respectively. The relative standard deviation (RSD, n = 5) of the retention times of nitrate and nitrite was 0.1% and RSD of chromatographic peak areas were 0.4 and 0.2%, respectively. The method was successfully used for analysis of the anions in groundwater. Recovery of nitrate and nitrite was 99.1 and 105%, respectively.     

GC–MS Method Development for the Analyses of Thiophenes from Solvent Extracts of Tagetes patula L

A method for isotachophoretic determination of potassium and ammonium cations in fertilizers and silage was developed. A capillary of 0.4 mm i.d. and 100 mm effective length made of fluorinated ethylene–propylene copolymer was filled with an electrolyte system consisting of 10 mmol L⁻¹ RbOH + 0.1% (w/v) hydroxyethylcellulose, adjusted to pH 9.0 with l-histidine (leading electrolyte) and 10 mmol L⁻¹ lithium citrate (terminating electrolyte). Using contactless conductivity detection, the calibration curves in the tested concentration range up to 0.5 mmol L⁻¹ were linear for both cations. The concentration detection limits for potassium and ammonium were 2.9 and 2.7 μmol L⁻¹, respectively. RSD values of step lengths (n = 6) were 1.3% for potassium and 1.5% for ammonium. The separation time was about 20 min. Similar results were obtained with cesium cation used as the leading ion, however, in the system with rubidium better resolution of other cations present in tested matrices was reached. The elaborated method is simple to perform, sufficiently sensitive and accurate and can be recommended as an alternative procedure to the methods used so far for the determination of potassium and ammonium.

     

Pulsed voltammetric/amperometric detection of polycyclic aromatic sulfur heterocycles (PASHs) at the gold disc electrode for studies in petroleum asphalts

This work describes the voltammetric and amperometric behavior of a high number of PASHs (sulfides, thiophenes, benzothiophenes, dibenzothiophenes, indenothiophenes, naphtothiophenes, thienothiophenes, phenanthrothiophenes, and acenaphtothiophenes) at gold disc electrodes aiming at their identification and determination in petroleum asphalts. The adsorption/redox processes expected for sulfur compounds at gold electrodes could be observed in all the studied PASHs in DMSO and hydromethanolic medium. Differential pulse (DP) voltammetry in non-aqueous solutions (0.1 mol L⁻¹ NaClO₄ in DMSO) was approached for determining non-volatile PASHs in asphalts submitted to different aging processes. It was found herein that the DP voltammetric monitoring of PASH oxidation at + 0.7 V (vs. Ag/AgCl/LiCl 3 mol L⁻¹) for virgin/aged asphalts can be used for the comparative study of asphalts based on the consumption of PASHs. Additionally, pulsed amperometric detection (PAD) in hydroalcoholic solution (10 mmol L⁻¹ acetate buffer in 65% methanol) coupled with a chromatographic separation was approached for determining volatile PASHs in asphalts submitted to thermal decomposition processes. A detection cycle of 2 s involving oxidative (0.4 s at + 0.4 V) and reductive (1.2 s at − 1.0 V) cleaning pulses after a detection pulse of − 0.8 V (0.4 s) applied successively to the gold electrode (vs. Pd/PdO) was found to be optimal for regenerating the gold surface during successive chromatographic runs of PASHs. Thus, reversed-phase liquid chromatography (LC)–coupled PAD was found useful to separate a complex mixture of PASHs. The optimized PAD and LC separation was further applied to investigate the presence of electroactive PASHs as volatile compounds in asphalt fumes generated at 260 °C.

     

Determination of Vitamins A and E Exploiting Cloud Point Extraction and Micellar Liquid Chromatography

Cloud point extraction and micellar chromatographic methods were developed for determination of vitamins A and E. The stationary phase was C18 and the mobile phase was 3.00% (w/v) SDS, 15.0% (v/v) butyl alcohol and 0.02 mol L^?1 phosphate buffer solution at pH 7.0. The retention times for vitamins A and E were 9.6 and 13.0, respectively. The extraction solution was 100 mmol L^?1 Triton X-100, 650 mg NaCl and 1.0% ascorbic acid at 70°C for 30 min. The method is precise (r.s.d. < 7%), the linear range was from 5.0 up to 360.0 mg L^?1 for both vitamins. Recovery test showed recuperation between 90.2 and 99.2%, and LOD and LOQ of 0.234 and 0.108 mg L^?1, 0.780 and 0.360 mg L^?1 to vitamins A and E were found.     

SPE and LC–ESI–MS for Quantitative Analysis of Mitiglinide in Human Plasma in a Bioequivalence Study

Liquid chromatography–electrospray ionization mass spectrometry has been used for rapid, selective, and sensitive quantitative analysis of mitiglinide in human plasma. Sample pretreatment involved solid-phase extraction from plasma with gliclazide as internal standard. Separation was performed on a C₁₈ column (150 × 2.0 mm) with 71:29 (v/v) acetonitrile–water (containing 0.1% formic acid and 0.2 mmol L^?1 ammonium acetate) as mobile phase at a flow rate of 0.2 mL min^?1. The method was validated then successfully applied to a clinical bioequivalence study of mitiglinide in 20 healthy volunteers after oral administration.     

Quantitative Analysis of Genistein in Human Plasma by Online Concentration CE with UV Detection

A rapid capillary electrophoresis method based on online acid barrage stacking has been successfully established for analysis of trace amounts of genistein in human plasma. Genistein was analyzed within 8 min, with 200 mmol L^?1 citric acid (pH 1.7) as acid barrage, and injection times of 180 and 30 s for sample and acid, respectively. Good linearity was obtained in the range 0.05–5 mg L^?1 and the limit of detection was 0.03 mg L^?1. Compared with normal sample injection, this method resulted in more than a fiftyfold improvement in detection sensitivity. The technique has potential for use in studies of genistein metabolism and of exposure levels in humans.     

Flow‐Injection Pulsed‐Amperometric Determination of Free Glycerol in Biodiesel at a Gold Electrode

This work reports the highly‐sensitive amperometric determination of free glycerol in biodiesel at a gold electrode adapted in a flow‐injection analysis (FIA) cell. The amperometric method involved the continuous application of three sequential pulses to the working electrode (+250 mV, +700 mV, and ?200 mV, for 100 ms each). This sequence of potential pulses eliminated electrode passivation and dramatically increased the analytical signal. The proposed FIA‐amperometric method presented low relative standard deviation between injections (1.5 %, n=15), high analytical frequency (85 h^?1), satisfactory recovery values (93–118 %) for spiked samples, wide linear range (from 1 to 300 µmol L^?1), and low detection limit (0.5 µmol L^?1).     

Analysis of Arecoline in Rat Urine, and Identification of its Metabolites, by Liquid Chromatography–Tandem Mass Spectrometry

A simple and rapid high-performance liquid chromatographic–electrospray ionization (ESI) tandem mass spectrometric method has been developed for elucidation of the structures of the metabolites of arecoline in rat urine after administration of a single dose (20 mg kg^?1). The urine samples were purified on a C₁₈ solid-phase extraction cartridge and analysis was then performed on a reversed-phase C₁₈ column with 60:40 (v/v) methanol–0.01% triethylamine solution (2 mmol L^?1, adjusted to pH 3.5 with formic acid) as mobile phase and detection by on-line MS–MS. Identification of the metabolites and elucidation of their structures were performed by comparing molecular masses (ΔM), retention-times, and product ion spectra with those of the parent drug. The parent drug arecoline, four phase-I metabolites, and one phase-II metabolite were identified in rat urine.     

Evaluation of the Potentialities of a Carbon Nanotubes/Silicone Rubber Composite Electrode in the Determination of Hydrochlorothiazide

A multiwall carbon nanotube/silicone rubber (MWCNT/SR) composite electrode has been used for the determination of hydrochlorothiazide (HCTZ) in pharmaceutical formulations by differential pulse voltammetry (DPV). The electro-oxidation process was evaluated by cyclic voltammetry, from which it was observed that HCTZ presents an irreversible oxidation peak at 0.82 V vs. saturated calomel electrode (SCE) in the potential range from 0.5 to 1.1 V, in Britton-Robinson buffer pH 7.0 at MWCNT/SR. HCTZ was determined by DPV using a MWCNT/SR 70% (MWCNT, m/m) composite electrode after the optimization of the experimental parameters. The linear range was from 5.0 to 70.0 µ mol L^?1, with a limit of detection (LOD) of 2.6 µ mol L^?1. The HCTZ was determined in pharmaceutical formulations using the proposed composite electrode and the results agreed with those from the official high performance liquid chromatography (HPLC) method within 95% confidence level, according to the t-Student test.     

Determination of antimony(III) and (V) in natural water by cathodic stripping voltammetry with in-situ plated bismuth film electrode

A method is described for the sequential determination of Sb(III) and Sb(V) using Osteryoung square wave cathodic stripping voltammetry. It employs an in-situ plated bismuth-film on an edge-plane graphite substrate as the working electrode. Selective electro-deposition of Sb(III)/Sb(V) is accomplished by applying a potential of ?500 mV vs. Ag/AgCl, followed by reduction to stibine at a more negative potential in the stripping step. Stripping was carried out by applying a square wave waveform between ?500 and ?1400 mV to the antimony deposited. The stripping peak current at ?1150 mV is directly proportional to the concentration of Sb( III)/Sb(V). The calibration plots for Sb (III) were linear up to 12.0?µg L^?1 depending on the time of deposition. The calibration plots for Sb (V) were linear up to 7.0?µg L^?1, also depending on the time of deposition. The relative standard deviation in the determination of 0.1?µg L^?1 of Sb(III) is 4.0% (n?=?5), and the limit of detection is as low as 2 ng L^?1. In case of 0.1?µg L^?1 Sb(V), the relative standard deviation is 3.0% (n?=?5) and the detection limit also is 2 ng L^?1. The method was applied to the analysis of river and sea water samples.     

An amperometric uric acid biosensor based on chitosan-carbon nanotubes electrospun nanofiber on silver nanoparticles

A novel amperometric uric acid biosensor was fabricated by immobilizing uricase on an electrospun nanocomposite of chitosan-carbon nanotubes nanofiber (Chi–CNTsNF) covering an electrodeposited layer of silver nanoparticles (AgNPs) on a gold electrode (uricase/Chi–CNTsNF/AgNPs/Au). The uric acid response was determined at an optimum applied potential of ?0.35 V vs Ag/AgCl in a flow-injection system based on the change of the reduction current for dissolved oxygen during oxidation of uric acid by the immobilized uricase. The response was directly proportional to the uric acid concentration. Under the optimum conditions, the fabricated uric acid biosensor had a very wide linear range, 1.0–400 μmol L^?1, with a very low limit of detection of 1.0 μmol L^?1 (s/n?=?3). The operational stability of the uricase/Chi–CNTsNF/AgNPs/Au biosensor (up to 205 injections) was excellent and the storage life was more than six weeks. A low Michaelis–Menten constant of 0.21 mmol L^?1 indicated that the immobilized uricase had high affinity for uric acid. The presence of potential common interfering substances, for example ascorbic acid, glucose, and lactic acid, had negligible effects on the performance of the biosensor. When used for analysis of uric acid in serum samples, the results agreed well with those obtained by use of the standard enzymatic colorimetric method (P?>?0.05).

Qualitative and Quantitative Determination of Oligonucleotides by Non-Gel Capillary Electrophoresis

A novel simple non-gel capillary electrophoresis (NGCE) method was developed for the qualitative and quantitative determination of oligonucleotides (ODNs). ODNs were synthesized in a DNA synthesizer and separated by NGCE under optimized conditions as follows: 25 mmol L^?1 Tris?Cboric?CEDTA buffer (pH 8.0) with 7 mmol L^?1 urea in the presence of 20% (w/v) polyethylene glycol (PEG) 35000 at 30 °C and ?20 kV. Single-base differences, in which there are differences in the base quantity and the single-base structure with the same base quantity, can be identified by the proposed method, and the quantitative determination was carried out. The obtained regression equation revealed a good linear relationship between the peak area ratio and the ODNs concentration. The correlation coefficient was 0.9986 and the relative standard deviation (RSD) of the precision was <3.6% (intro-day) and <6.2% (inter-day), respectively. The recoveries of three concentrations (high, middle, and low) were between 99.6% and 107.6%. The established method is sensitive, simple, economical, and can be used in gene mutation detection, pharmacokinetics study of nucleic acid drugs, and so on.     

RP-LC and HPTLC Methods for the Determination of Olmesartan Medoxomil and Hydrochlorothiazide in Combined Tablet Dosage Forms

Two new, rapid, precise, accurate and specific chromatographic methods were described for the simultaneous determination of olmesartan medoxomil and hydrochlorothiazide in combined tablet dosage forms. The first method was based on reversed phase liquid chromatography using an Eurosphere 100 RP C18 column (250 × 4.6 mm ID, 5 μm). The mobile phase was methanol–0.05% o-phosphoric acid (60:40 v/v) at a flow rate of 1.0 mL min^?1. Commercially available tablets and laboratory mixtures containing both drugs were assayed and detected using a UV detector at 270 nm. The second method involved silica gel 60 F₂₅₄ high performance thin layer chromatography and densitometric detection at 254 nm using acetonitrile–ethyl acetate–glacial acid (7:3:0.4 v/v/v) as the mobile phase. Calibration curves ranged between 200–600 and 125–375 ng spot^?1 for olmesartan and hydrochlorothiazide, respectively.     

Determination of Lipoic Acid in Biological Samples with Acetonitrile–Salt Stacking Method in CE

An acetonitrile–salt stacking method was established for the assay of lipoic acid (LA) in biological samples. Samples were deproteinized with acetonitrile at a final concentration of 60 % (v/v) and then injected hydrodynamically at 3.45 × 10³ Pa for 180.0 s. The optimum background electrolyte was found to be 90.0 mmol L^?1 pH 9.1 borate buffer. LA could be detected within 35 min at +7.0 kV with satisfactory repeatability (relative standard deviations, RSDs, of migration times and peak areas were both below 10 % for intraday and interday; n = 6/9) and a relatively low limit of detection of ca. 0.5 μmol L^?1.     

Liquid–Liquid–Liquid Micro Extraction Combined with CE for the Determination of Rare Earth Elements in Water Samples

A simple method for determination of rare earth elements (REEs) by liquid–liquid–liquid microextraction (LLLME) coupled with capillary electrophoresis and ultraviolet technique was developed. In the LLLME system, 40 mmol L^?1 4-benzoyl-3-methy-1-phenyl-5-pyrazolinone (PMBP) acted as extractant and 4% (v/v) formic acid was used as back-extraction solution. The parameters influencing the LLLME, including the type of the organic solvent, sample pH, formic acid concentration, PMBP concentration, extraction time, volume of organic solvent, stirring rate and phase volume ratio, were investigated. Under the optimized conditions, the detection limits (S/N = 3) of REEs were in the range of 0.19–0.70 ng mL^?1. The developed method was successfully applied to the determination of trace amounts of REEs in water samples.