Time-resolved electrochemiluminescence of platinum(II) coproporphyrin

Cathodic pulse polarisation of oxide-covered aluminium electrodes can generate electrochemiluminescence (ECL) from metalloporphyrins. This is based on the tunnel emission of hot electrons into aqueous electrolyte solution, which probably results in the generation of hydrated electrons as reducing mediators. These tunnel emitted electrons allow the production of highly reactive radicals, such as sulfate radicals from peroxodisulfate ions, which can induce strong redox luminescence from various organic chemiluminophores including metalloporphyrins. The work presented here illustrates the generation of ECL from platinum(II) coproporphyrin (PtCP) and its bovine serum albumin (BSA) conjugate. This allows the detection of these molecules below nanomolar concentrations and over several orders of magnitude of concentration. The relatively long luminescence lifetime of PtCP allows discrimination from the background ECL signal using time resolved measurements, leading to higher sensitivity and the detection of PtCP-BSA indicates the potential use of metalloporphyrins as labels in ECL-based bioassays such as immunoassays and DNA-binding assays.     

Instrumental neutron activation analysis of ferromanganese oxide encrustations of Indian Ocean by the k0 NAA method

Hot electron injection into aqueous electrolyte solution was studied with electrochemiluminescence and electron paramagnetic resonance (EPR) methods. Both methods provide further indirect support for the previously proposed hot electron emission mechanisms from thin insulating film-coated electrodes to aqueous electrolyte solution. The results do not rule out the possibility of hydrated electron being as a cathodic intermediate in the reduction reactions at cathodically pulse-polarized thin insulating film-coated electrodes. However, no direct evidence for electrochemical generation of hydrated electrons could be obtained with EPR, only spin-trapping experiments could give information about the primary cathodic steps.     

Electrogenerated chemiluminescence induced by sequential hot electron and hole injection into aqueous electrolyte solution

Hole injection into aqueous electrolyte solution is proposed to occur when oxide-coated aluminum electrode is anodically pulse-polarized by a voltage pulse train containing sufficiently high-voltage anodic pulses. The effects of anodic pulses are studied by using an aromatic Tb(III) chelate as a probe known to produce intensive hot electron-induced electrochemiluminescence (HECL) with plain cathodic pulses and preoxidized electrodes. The presently studied system allows injection of hot electrons and holes successively into aqueous electrolyte solutions and can be utilized in detecting electrochemiluminescent labels in fully aqueous solutions, and actually, the system is suggested to be quite close to a pulse radiolysis system providing hydrated electrons and hydroxyl radicals as the primary radicals in aqueous solution without the problems and hazards of ionizing radiation. The analytical power of the present excitation waveforms are that they allow detection of electrochemiluminescent labels at very low detection limits in bioaffinity assays such as in immunoassays or DNA probe assays. The two important properties of the present waveforms are: (i) they provide in situ oxidation of the electrode surface resulting in the desired oxide film thickness and (ii) they can provide one-electron oxidants for the system by hole injection either via F- and F⁺-center band of the oxide or by direct hole injection to valence band of water at highly anodic pulse amplitudes.     

Hot Electron Induced Cathodic Electrochemiluminescence at Disposable Screen Printed Carbon Electrodes

Hot electron induced cathodic electrochemiluminescence (ECL) was observed at screen printed carbon electrodes (SPCEs) during pulse polarization. The thin insulating film resulted from the printing inks was found to be suitable for generating hot electrons, which can further be converted to hydrated electrons and induce the subsequent luminescence. Compared with disposable Al/Al₂O₃ electrode, SPCEs show more stable and reproducible ECL in a wider pH range without background emission. A sensitive ECL method for determination of quercetin is proposed. The detection limit is 8.0×10^?10 mol L^?1(S/N=3), which is two magnitudes lower than that of common ECL method.     

Cathodic electrochemiluminescence at double barrier Al/Al2O3/Al/Al2O3 tunnel emission electrodes

Double insulating barrier tunnel emission electrodes were fabricated by adding a new pure aluminum layer upon oxidized aluminum electrodes by vacuum evaporation and thermally oxidizing the new aluminum layer in air at room temperature. Resulting Al/Al₂O₃/Al/Al₂O₃ electrodes allow the use of various aluminum alloys in the electrode body necessary for hardness or shaping ability of the electrode while obtaining the luminescence properties of pure aluminum oxide. During electrical excitation of luminescent labels by cathodic hot electron injection into aqueous electrolyte solution, the background noise is mainly based on high-field-induced solid-state electroluminescence and F-center luminescence of the outer aluminum oxide film. The more defect states and/or impurity centers the outer oxide film contains, the higher is the background emission intensity. The present electrode fabrication method provides a considerable improvement in signal-to-noise ratio for time-resolved electrochemiluminescence (TR-ECL) measurements when the original native oxide film of the electrode body contains luminescence centers displaying long-lived luminescence. The excellent performance of the present electrodes is demonstrated by extremely low-level detection of Tb(III) chelates, luminol, Pt(II) coproporphyrin and Tb(III) labels in an immunometric immunoassay by time-resolved electrochemiluminescence.     

On the nature of solubilized water clusters in aerosol OT/alkane solutions. A study of the formation of hydrated electrons and 1,8-anilinonaphthalene sulphonate fluorescence

The pulse radiolysis of dioctyl sulphosuccinate (aerosol-OT) H₂O/heptane solutions leads to formation of hydrated electrons in the aqueous core of the inverted aerosol-OT micelles. The hydrated electrons are produced via direct interaction of the radiation with the aqueous regions and scavenging of electrons formed initially in the hydrocarbon phase by the water bubbles. The scavenging efficiency decreases with decreasing radius of the water cluster. Hydrated electrons are not formed below a critical size of the solubilized water particles.The quantum yield and wavelength of the maximum of the aniline-naphthalene sulphonate (ANS) fluorescence are strongly dependent on the water content of aerosol-OT inverted micelles. The fluorescence behavior indicates an increase of polarity with increasing cluster radius. The polarity of very large water clusters (r ≈ 73 Å) is still lower than that of bulk water. Water which is bound to Na⁺ counterions cannot effectively participate in the solvation of the dipolar ANS excited states.     

Intrinsic and 1-aminonaphthalene-4-sulfonate-specific extrinsic lyoluminescences of X-ray irradiated sodium chloride

1-Aminonaphthalene-4-sulfonate (ANS)-specific extrinsic lyoluminescence (LL) of X-ray irradiated sodium chloride is observed at 425 nm when the irradiated salt is dissolved in an aqueous solution of ANS. The paper discusses, in detail, the mechanism of the ANS-specific LL and its analytical applicability. Also, the intrinsic LL of X-ray irradiated sodium chloride is studied. Hydrated electron as well as hole scavenger experiments support the proposal that in the case of the intrinsic LL of X-ray irradiated sodium chloride, trapped electrons (mainly F-center electrons) are released and hydrated whereas trapped holes (V-centers) remain surface-bound and are only partially hydrated before recombination occurs. These hydrated electrons and dissolving solid surface-bound hole centers, which are probably only partially hydrated, are able to act as reducing and oxidizing agents, respectively, in the luminophore oxidation-initiated reductive excitation pathway of ANS. Solution additives (halides and pseudohalides) show that in the chemiluminescence processes in question, oxidizing agents will follow the Marcus theory of electron transfer reactions. The LL method described allows the determination of ANS in the concentration range ≈10⁻¹¹ − 10⁻⁷ M. This suggests that aminonaphthalene derivatives can be used as label molecules in high sensitivity lyoluminobioaffinity assays.     

Investigations on current transients in porous alumina films during re-anodizing using the electrochemical quartz crystal microbalance

Current transients and mass variations in as-prepared and heat-treated anodic alumina films were measured during re-anodizing by means of voltammetry and electrochemical quartz crystal microbalance (EQCM), respectively. Aluminum electrodes (100 nm) on quartz crystals were prepared by thermal evaporation. Anodic alumina films were formed on the surface of Al electrodes in aqueous solutions of oxalic (0.3 M) and phosphoric (0.6 M) acid in the potentiostatic regime. The EQCM experiments did not detect an overshoot in the mass variation of the Al electrode during re-anodizing of heat-treated anodic alumina films. The observed current overshoot in transients proved the presence of electrons and electron holes injected from the contacts in the bulk of the oxide. This can be explained by the emergence of excess electrons in the barrier layer of the alumina films due to a change in the mobility of the electrons.     

Dual Enhancement of Gold Nanocluster Electrochemiluminescence: Electrocatalytic Excitation and Aggregation-Induced Emission

Ligand-protected gold nanoclusters (AuNCs) have emerged as a new class of electrochemiluminescence (ECL) luminophores for their interesting catalytic and emission properties, although their quantum yield (Φ_ECL) in aqueous medium is low with a poor mechanistic understanding of the ECL process. Now it is shown that drying AuNCs on electrodes enabled both enhanced electrochemical excitation by an electrocatalytic effect, and enhanced emission by aggregation-induced ECL (AIECL) for 6-aza-2-thiothymine (ATT) protected AuNCs with triethylamine (TEA) as a coreactant. The dried ATT-AuNCs/TEA system resulted in highly stable visual ECL with a Φ_ECL of 78 %, and a similar enhancement was also achieved with methionine-capped AuNCs. The drying enabled dual-enhancement mechanism has solved a challenging mechanistic problem for AuNC ECL probes, and can guide further rational design of ECL emitters.     

Electrochemical Generation of Hot Electrons in Fully Aqueous Solutions at Tetrahedral Amorphous Carbon Thin Film Electrodes and Electrochemiluminescence Immunoassay of Serum Amyloid A

Electrochemistry of hot electrons in fully aqueous solutions at tetrahedral amorphous carbon thin film electrodes is discussed. The generation of these highly reducing chemical species was confirmed by normal pulse voltammetry and several electrochemiluminescent systems. Electron transfer into pre-existing solvent cavities was observed at approximately −2.65 V vs. Ag/AgCl (sat.). Electrogenerated hot electrons were utilized as chemiluminescent mediators in heterogeneous sandwich immunoassay of Serum Amyloid A. The calibration curve was linear over four orders of magnitude and the detection limit was 85 ng L⁻¹ that demonstrates the efficiency of hot electron generation at this electrode material.     

Dual Enhancement of Gold Nanocluster Electrochemiluminescence: Electrocatalytic Excitation and Aggregation‐Induced Emission

Ligand‐protected gold nanoclusters (AuNCs) have emerged as a new class of electrochemiluminescence (ECL) luminophores for their interesting catalytic and emission properties, although their quantum yield (Φ_ECL) in aqueous medium is low with a poor mechanistic understanding of the ECL process. Now it is shown that drying AuNCs on electrodes enabled both enhanced electrochemical excitation by an electrocatalytic effect, and enhanced emission by aggregation‐induced ECL (AIECL) for 6‐aza‐2‐thiothymine (ATT) protected AuNCs with triethylamine (TEA) as a coreactant. The dried ATT‐AuNCs/TEA system resulted in highly stable visual ECL with a Φ_ECL of 78 %, and a similar enhancement was also achieved with methionine‐capped AuNCs. The drying enabled dual‐enhancement mechanism has solved a challenging mechanistic problem for AuNC ECL probes, and can guide further rational design of ECL emitters.     

Nonadiabatic molecular dynamics simulations of correlated electrons in solution. 2. A prediction for the observation of hydrated dielectrons with pump-probe spectroscopy

The hydrated dielectron is a highly correlated, two-electron, solvent-supported state consisting of two spin-paired electrons confined to a single cavity in liquid water. Although dielectrons have been predicted to exist theoretically and have been used to explain the lack of ionic strength effect in the bimolecular reaction kinetics of hydrated electrons, they have not yet been observed directly. In this paper, we use the extensive nonadiabatic mixed quantum/classical excited-state molecular dynamics simulations from the previous paper to calculate the transient spectroscopy of hydrated dielectrons. Because our simulations use full configuration interaction (CI) to determine the ground and excited state two-electron wave functions at every instant, our nonequilibrium simulations allow us to compute the absorption, stimulated emission (SE), and bleach spectroscopic signals of both singlet and triplet dielectrons following excitation by ultraviolet light. Excited singlet dielectrons are predicted to display strong SE in the mid infrared and a transient absorption in the near-infrared. The near-infrared transient absorption of the singlet dielectron, which occurs near the peak of the (single) hydrated electron's equilibrium absorption, arises because the two electrons tend to separate in the excited state. In contrast, excitation of the hydrated electron gives a bleach signal in this wavelength region. Thus, our calculations suggest a clear pump-probe spectroscopic signature that may be used in the laboratory to distinguish hydrated singlet dielectrons from hydrated electrons: By choosing an excitation energy that is to the blue of the peak of the hydrated electron's absorption spectrum and probing near the maximum of the single electron's absorption, the single electron's transient bleach signal should shrink or even turn into a net absorption as sample conditions are varied to produce more dielectrons.     

A pulse radiolysis study of oil/water microemulsions

Absorption spectrum and the yield of e_aq⁻ determined in quaternary benzene/water and dodecane/water microemulsions were found to be identical with those in pure water. This indicates that the excess electrons produced in the oil droplets cross the oil/water interface and appear in the aqueous phase as hydrated electrons. On the contrary, it was found that the OH radical yield measured by converting into (SCN)₂^.− was directly proportional to the water content and there was no contribution from the oil phase. The e_aq⁻ decay in aerated microemulsion showed that the [O₂] in the aqueous phase was decreasing with continuous pulse irradiation and the estimated G(–O₂) in the oil was higher than in water. However, peroxides were predominantly formed in the aqueous phase and almost not in the oil. Rate constants for the addition of e_aq⁻ and OH to benzene in the benzene/water microemulsion and the following bimolecular decay of cyclohexadienyl and hydroxycyclohexadienyl radicals agree well with those reported in aqueous solutions.     

Ultrafast geminate recombination after photodetachment of aqueous hydroxide

The photodetachment of aqueous hydroxide (OH(?)(aq) and OD(?)(aq)) is studied using femtosecond pump?probe and pump?repump?probe spectroscopy. The electron is detached after excitation of the hydroxide ion to a charge-transfer-to-solvent (CTTS) state at 202 nm. An early intermediate is observed that builds up within 160 fs and is assigned to nonequilibrated OH?electron pairs. The subsequent dynamics are governed by thermalization, partial recombination, and dissociation of the pairs, yielding the final hydrated electrons and hydroxyl radicals. An additional pulse at 810 nm is used for secondary excitation of the intermediate species so that more insight is gained into the recombination process(es). Using this technique we observe a novel geminate recombination channel of OH with adjacent hydrated electrons. This channel leads to ultrafast quenching (700 fs) of almost half the initial number of radicals. The fast mechanism displays an isotope effect of 1.4 (for OD(?)(aq) quantum yield 35%, time constant 1.0 ps). This process was not observed in similar experiments on aqueous bromide and seems to be related to the special properties of the hydroxide ion and its local H-bonding environment. Our findings underline the high reactivity of the prehydrated electron.     

Hydrated Electron Transfer to Nucleobases in Aqueous Solutions Revealed by Ab Initio Molecular Dynamics Simulations

We present an ab initio molecular dynamics (AIMD) simulation study into the transfer dynamics of an excess electron from its cavity‐shaped hydrated electron state to a hydrated nucleobase (NB)‐bound state. In contrast to the traditional view that electron localization at NBs (G/A/C/T), which is the first step for electron‐induced DNA damage, is related only to dry or prehydrated electrons, and a fully hydrated electron no longer transfers to NBs, our AIMD simulations indicate that a fully hydrated electron can still transfer to NBs. We monitored the transfer dynamics of fully hydrated electrons towards hydrated NBs in aqueous solutions by using AIMD simulations and found that due to solution‐structure fluctuation and attraction of NBs, a fully hydrated electron can transfer to a NB gradually over time. Concurrently, the hydrated electron cavity gradually reorganizes, distorts, and even breaks. The transfer could be completed in about 120–200 fs in four aqueous NB solutions, depending on the electron‐binding ability of hydrated NBs and the structural fluctuation of the solution. The transferring electron resides in the π*‐type lowest unoccupied molecular orbital of the NB, which leads to a hydrated NB anion. Clearly, the observed transfer of hydrated electrons can be attributed to the strong electron‐binding ability of hydrated NBs over the hydrated electron cavity, which is the driving force, and the transfer dynamics is structure‐fluctuation controlled. This work provides new insights into the evolution dynamics of hydrated electrons and provides some helpful information for understanding the DNA‐damage mechanism in solution.     

Preparation of lead and tin oxide thin films by spin coating and their application on the electrodegradation of organic pollutants

In this work, lead and tin oxide films (Pb _x O _y /SnO₂) were prepared, using the spin coating technique. The influence of the temperature and duration of the thermal treatment on the final film composition were analysed. The metallic oxide films that were prepared, Pb _x O _y /SnO₂, were characterized by means of XRD, SEM/EDS and cyclic voltammetry. When different experimental preparation conditions were used different lead oxide phases were obtained. The electrochemical studies show that the films are stable and can be used as electrodes. Finally the films were tested as electrodes for the electrochemical degradation of a CHCl₃ aqueous solution.     

Hot tungsten clusters: competition between atom ejection and thermionic emission

This is a first report concerning the thermionic emission of electrons from hot metal clusters. Tungsten clusters were exposed to a 10 ns laser pulse, and the delayed emission of electrons from the clusters was recorded as a function of time after the excitation. A large yield of W _n ⁺ cluster ions, which were born as late as microseconds after the laser pulse, has been detected forn>4. Tungsten cluster ions created via thermionic emission show no measurable metastable decay during the flight time in the mass spectrometer. This indicates that they are colder than expected, if evaporative cooling after prompt ionization would prevail.     

3,4,9,10-Perylenetetracarboxylic Acid Derivatives, Their Spectral Behavior and Their Chemical Interaction with Hydrated Iron Oxide Nanopar

The photophysical properties such as electronic absorption, excitation and emission spectra as well as molar absorptivity and fluorescence quantum yield of N,N‐bis(pyrimidenyl)‐3,4,9,10‐perylenetetracarboxylic diimide (PmPBD), N,N‐bis(pyridenyl)‐3,4,9,10‐perylenetetracarboxylic diimide (PyPBD) and N,N‐bis(4‐methylpyridenyl)‐3,4,9,10‐perylenetetracarboxylic diimide (MPyPBD) have been measured in different solvents. Both electronic absorption and fluorescence spectra are not sensitive to medium polarity, while the fluorescence quantum yield ((_f) is solvent dependent. Perylene derivatives under investigation undergo molecular aggregation to dimmer or larger aggregates in water. Dye solution in dimethylformmaide (DMF) gives laser emission at 565 nm upon pumping with 337.1 nm nitrogen laser pulse. The excitation energy transfer from 7‐dimethylamino‐4‐methylcoumarine (DMC) to PmPBD has been studied to improve the laser emission of PmPBD. The value of energy transfer rate constant (k_ET) and critical transfer distance (R₀) indicate a F?rster type energy transfer mechanism. There is a large interaction between the perylene compounds under investigation and the hydrated nanoparticles in the excited state therefore the fluorescence quenching rate constant of these derivatives by hydrated iron oxide nanoparticles has a large value.     

Slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry for the direct determination of metal impurities in aluminium oxide ceramic powders

A new analytical procedure for the direct determination of metal impurities (Cr, Cu, Fe and V) in aluminium oxide ceramic powders by slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICP-AES) is reported. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of impurity elements in aluminium oxide ceramic powders from the graphite tube. A vaporization stage with a long ramp time and a short hold time provided the possibility of temporal analyte-matrix separation. The experimental results indicated that a 10 microL 1% m/v slurry of aluminium oxide could be destroyed and vaporized completely with 600 micrograms PTFE under the selected conditions. Two aluminium oxide ceramic powder samples were used without any additional pretreatment. Analytical results obtained by using standard addition method with aqueous standard solution were checked by comparison of the results with pneumatic nebulization (PN)-ICP-AES based on the wet-chemical decomposition and analyte-matrix separation. The limits of detection (LODs) between 0.30 microgram g-1 (Fe) and 0.08 microgram g-1 (Cu) were achieved, and, the repeatability of measurements was mainly better than 10%.     

Binding of 8-anilino-1-naphthalenesulfonate to lecithin:cholesterol acyltransferase studied by fluorescence techniques

The solvatochromic fluorescent probe 8-anilino-1-naphthalenesulfonate (ANS) has been used to study the hydrophobicity and conformational dynamics of lecithin:cholesterol acyltransferase (LCAT). The ANS to LCAT binding constant was estimated from titrations with ANS, keeping a constant concentration of LCAT (2 microM). Apparent binding constant was found to be dependent on the excitation. For the direct excitation of ANS at 375 nm the binding constant was 4.7 microM(-1) and for UV excitation at 295 nm was 3.2 microM(-1). In the later case, not only ANS but also tryptophan (Trp) residues of LCAT is being excited. Fluorescence spectra and intensity decays show an efficient energy transfer from tryptophan residues to ANS. The apparent distance from Trp donor to ANS acceptor, estimated from the changes in donor lifetime was about 3 nm and depends on the ANS concentration. Steady-state and time-resolved fluorescence emission and anisotropies have been characterized. The lifetime of ANS bound to LCAT was above 16 ns which is characteristic for it being in a hydrophobic environment. The ANS labeled LCAT fluorescence anisotropy decay revealed the correlation time of 42 ns with a weak residual motion of 2.8 ns. These characteristics of ANS labeled LCAT fluorescence show that ANS is an excellent probe to study conformational changes of LCAT protein and its interactions with other macromolecules.