Thermal degradation behavior of polyamides having 2- and 4-hydroxycinnamic acid dimer components

Two new types of polyamides having anti head-to-tail hydroxycinnamic acid dimer component in the main chain were synthesized. Their thermal degradation behavior was investigated by TG-DSC analysis in comparison with those of their model compounds and the polyamides derived from anti head-to-head coumarin dimer. The key reactions in the thermal degradation were clarified to be lactonization and cyclic imide formation. The polyamide, derived from 4-hydroxycinnamic acid dimer and hexamethylenediamine, showed good heat stability. © 1993 John Wiley & Sons, Inc.     

Synthesis and reversible photocleavage of novel polyurethanes containing coumarin dimer components

Six polyurethanes containing coumarin dimer components in the main chain have been prepared by polyaddition of diisocyanates with anti head-to-head 7-hydroxycoumarin dimer or anti head-to-tail 7-hydroxy-4-methylcoumarin dimer. 7-Acetoxycoumarin and 7-acetoxy-4-methylcoumarin were first prepared and then photodimerized under 350 nm UV light to give anti head-to-head 7-acetoxycoumarin dimer and anti head-to-tail 7-acetoxy-4-methylcoumarin dimer, respectively. After hydrolyzing under acidic conditions to 7-hydroxycoumarin dimer and anti head-to-head 7-hydroxycoumarin dimer, they were polymerized with aliphatic and aromatic diisocyanates in N,N-dimethylacetamide to give the polyurethanes. Addition of dibutyltin dilaurate (T-12) as catalyst increases the polymer yield with the viscosity remaining almost unchanged. It was also found that lithium chloride enhances both the yield and viscosity of the polyurethanes by increasing their solubility possibly through complexation. The polyurethanes are symmetrically photocleaved at cyclobutane rings under 254 nm UV light to dicoumarins. Reversible photodimerization of the photocleaved compounds have also been investigated under 300 and 350 nm UV light. The polyurethanes from aromatic diisocyanates or with 4-methyl substituent exhibit greater reactivity in the photocleavage reaction. © 1997 John Wiley & Sons, Inc.     

Selectivity in the photodimerization of 6-alkylcoumarins

Coumarin and 6-alkylcoumarins (alkyl = C(1) to C(16)) were photodimerized in homogeneous solvents differing in polarity and in aqueous micellar solutions. The four possible photodimers, syn head-to-head (hh), anti head-to-head, syn head-to-tail (ht), and anti head-to-tail, were identified through a combination of X-ray analysis and NMR spectroscopy. In 6-methylcoumarin the concentration-corrected dimerization (quantum) yield increases with decreasing concentration of the educt; anti-hh was formed exclusively in nonpolar solvents and upon triplet sensitization and was the main product under all conditions except for ionic micellar systems, which direct to preferred syn-hh dimerization. Long alkyl substituents, however, lead to anti-hh in polar solvents and in micelles, too. Predominating ht dimer formation was observed for nonsubstituted coumarin in polar solvents only. Thus, syn/anti and hh/ht selectivity can be steered by varying the 6-alkyl substituent. Syn-hh photodimers of 6-methylcoumarin can be photochemically split into the monomers; they partly proved thermally unstable against acids, bases, methanol, and on SiO(2) surfaces.     

Synthesis and Properties of Polyamides of 2,2′-[Isopropylidenebis-(p-phenyleneoxy)] diacetic Acid

A group of six semiaromatic polyamides of 2,2′-[isopropylidenebis-(p-phenyleneoxy)]diacetic acid (Bisacid A₂) were synthesized by low-temperature solution polycondensation techniques. Six different diamines were condensed independently with Bisacid A₂ chloride in a mixture of N-methylpyrrolidone (NMP and hexamethylhosphoramide (HMPA). The polymers were obtained in 82–95% yield and possessed inherent viscosities in the range from 0.32 to 0.63 dL/g. The polyamides were characterized by IR and 'H-NMR spectra. The molecular weight and molecular weight distribution of the polyamides were determined by gel-permeation chromatography. The thermal stability, thermal degradation kinetics, crystallinity, density, and solubility were also determined. A model diamide (MDA) was synthesized from aniline and Bisacid A₂ chloride to confirm the formation of polyamides from diamines.     

Polyamides containing arylene sulfone ether linkages

Polyamides containing arylene sulfone ether linkages were synthesized from 4,4′-[sulfonylbis(p-phenyleneoxy)] dibenzoyl chloride (SPCI), 3,3′-[sulfonylbis(p-phenyleneoxy)] dibenzoyl chloride (SMCl), and arylene sulfone ether diamines (SED), by solution and interfacial polymerization techniques. In solution polymerization, the effect of various acid acceptors such as propylene oxide (PO), lithium chloride (LiCl)/lithium hydroxide (LiOH), and triethylamine (TEA) on molecular weight of the polyamides was studied. The effect of methyl substituted and unsubstituted aromatic sulfone ether diamines on molecular weight and thermal properties of polyamides was also studied. The polyamides prepared were characterized by solution viscosity, elemental analysis, thermal gravimetric analysis, differential scanning calorimetry, and x-ray diffraction. Physical and thermal properties of polyamides prepared from SPCl and SED were compared with the polyamides prepared from SMCl and SED.     

Ferrocene-containing polyesters and polyamides

A series of ferrocene-containing polyesters and polyamides were prepared by refluxing 1,1′-dichlorocarbonylferrocene with various diols and primary diamines in xylene–pyridine solvent. The polyamides were all solids, but some of the polyesters were liquids. Reported are the infrared spectra and solubility characteristics of all the polymers and, where possible, the molecular weight and molecular weight distributions. In general, these polyamides and polyesters were of relatively low molecular weight (below 4000), but the polyesters were readily chain extended and crosslinked by di- and triisocyanates. Elemental analyses are reported for all the polymers prepared.     

Polymers from a levopimaric acid–acrylonitrile Diels–Alder adduct: Synthesis and characterization

The Diels–Alder adduct of levopimaric acid with acrylonitrile was efficiently prepared from resin acids. Excellent addition reaction yields (ca. 95%) were obtained. The adduct was converted into polyamides by polycondensation with diamines. When the same adduct was subjected to a dehydrodecarboxylation reaction, a novel ketone dinitrile derivative was obtained. This trifunctional product was also converted into polyamides by polycondensation with diamines. When the ketone dinitrile was hydrolyzed in the presence of alkalies and the reaction product was chlorinated, a ketone diacid chloride was obtained. A polyester was synthesized by the polycondensation of the diacid chloride with a diol. The structures of the Diels–Alder adduct, ketone dinitrile derivative, ketone diacid chloride, and polymers were established by means of elemental analysis, IR and NMR spectroscopy, and molecular weight determinations. Both the polyamides and the polyester were low‐molecular‐weight polymers soluble in polar solvents. The thermal behavior of the monomers and polymers was evaluated by thermogravimetric analysis. The thermal studies showed that the polymers were fairly thermostable substances, except the polyester, which appeared to be a substance with good thermal stability. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6308–6322, 2005     

Synthesis and Characterization of Complex Mixtures Consisting of Cyclic and Linear Polyamides from Ethyl Bis-Ketal Galactarates

Bis-ketal-protected diethyl galactarate was condensed with different diamines to prepare sugar-based polyamides. Ketal-protected polyamides, which are soluble in organic solvents, were deprotected with 90% trifluoroacetic acid to yield water insoluble materials. FTIR, NMR, GPC, MALDI-TOF, ESI and TGA techniques were used to characterize the structure and the properties of these biodegradable materials.

D-galactaric acid-based polyamides are complex mixtures of cyclic and linear structures. High molecular weight linear polymer formation was limited by competitive cyclization reactions. The percentage of cyclization was highly dependent on the nature of the diamine used. Polycondensation with linear aliphatic diamines favored the formation of macrocycles, identified by MALDI-TOF and ESI.     

Synthesis of polyamides from linear bisanhydrides and diamines

The aminolysis of benzoic mesitoic anhydride was studied in a model system to select the reaction site by steric effect and was found to occur exclusively at the carbonyl group of the benzoic acid. Solution polycondensation of new linear bisanhydrides, terephthalic bis(mesitoic anhydride) and adipic bis(mesitoic anhydride), with aromatic diamines in polar aprotic solvents that contained lithium chloride at room temperature, afforded polyamides with high molecular weight. The interfacial polycondensation in a dichloromethane-water system also successfully yielded polyamides from aliphatic diamines.     

Condensation polymers from 1,2,5-thiadiazole-3,4-dicarboxylic acid

A series of polyamides was prepared by interfacial polymerization of diamines with 1,2,5-thiadiazole-3,4-dicarbonyl chloride. Polyamides from secondary cycloaliphatic diamines and aromatic diamines have high softening points, high glass transition temperatures, and good thermal stability. Secondary amines, in particular cycloaliphatic secondary amines, form very high molecular weight polyamides. The polyamide from trans-2,5-dimethylpiperazine and 1,2,5-thiadiazole-3,4-dicarbonyl chloride is soluble in chloroform and 1,1,2-trichloroethane and has been cast into films and spun into fibers from those solvents. Fibers of this polymer are strong and have very high work recovery from small strains. In addition, these fibers show good retention of strength and work recovery over a range of temperatures and humidities.     

Cyclic Aromatic Polyamides via the Triphenylphosphite Method

Abstract

5‐tert‐Butyl‐isophthalic acid (TIPA) was polycondensed with three different aromatic diamines by means of triphenylphosphite (TPP) and pyridine. The resulting polyamides were characterized by solution viscosities and MALDI‐TOF mass spectra (m.s.). These m.s. revealed significant fractions of cyclic oligo‐ and polyamides in all samples. In polyamides of high molecular weight, only cycles were detectable (observed up to masses of 13,000 Da). Three poly(amide‐imide)s were prepared by TPP‐mediated polycondensation of trimellitic anhydride (TMA) and three aromatic diamines. Although relatively high molar masses were obtained, the MALDI‐TOF m.s. displayed the peaks of linear chains in addition to those of cyclic polymers. The results together suggest that the side reactions mainly occur at the amino endgroups.     

Direct synthesis of polyamides via catalytic dehydrogenation of diols and diamines

We report a direct synthesis of polyamides via catalytic dehydrogenation of diols and diamines. A PNN pincer ruthenium complex, the Milstein catalyst, was used for this reaction and polyamides with number average molecular weight from ～10 to 30 kDa could be obtained from a wide variety of diols and diamines bearing aliphatic or aromatic, linear or cyclic spacers. Because of the high catalytic selectivity of primary amine over secondary amine, polyamines could be conveniently incorporated into linear polyamides without tedious protection/deprotection steps. Compared with conventional condensation method, this catalytic system avoids the requirement of stoichiometric preactivation or in situ activation reagents and provides a much cleaner process with high atomic economy.     

Thermally reactive aromatic polyamides

2,5-Bis(phenylethynyl)terephthaloyl chloride and 4,6-bis-(phenylethynyl)isophthaloyl chloride were synthesized in a multistep reaction scheme from 2,5-dibromoterephthaldehyde and 4,6-dibromoisophthaldehyde, respectively. Low temperature solution polycondensation of these novel monomers and tolane-2,4′-dicarbonyl chloride with aromatic diamines yielded aromatic polyamides containing phenylethynyl moieties. Inherent viscosities of 0.20–0.51 dL/g were recorded. Attempts to carry out the homopolymerization of 2-(3-aminophenylethynyl)benzoyl chloride hydrochloride under similar conditions led to low molecular weight polyamide. Under differential scanning calorimetry and thermal mechanical analysis, the polyamides exhibited strong exotherms with onset occurring in the 185–225°C range. The exotherms were attributable to intramolecular cycloaddition of phenylethynyl moieties with amide groups to give polybenzalphthalimidine structures. Curing of a pressed pellet specimen for 16 h at 250°C under a nitrogen atmosphere resulted in partial conversion to a polybenzalphthalimidine structure with a concomitant increase in the polymer glass transition temperature. Isothermal aging in air of the cured specimen at 316°C (600°F) led to 25% weight loss after 200 h.     

Synthesis of polyamides from active N,N′-diacylbis-2-benzothiazolones and diamines under mild conditions

The aminolysis of N-benzoyl-2-benzothiazolone was studied in model systems and was found to give excellent yields of N-substituted benzamides at room temperature. Solution polycondensation of new bisamides, N,N′-adipoylbis-2-benzothiazolone and N,N′-isophthaloylbis-2-benzothiazolone, proceeded fairly slowly with both aromatic and aliphatic diamines at room temperature to yield polyamides having inherent viscosities up to 1.5. Hexamethylphosphoramide was the best polycondensation medium among some polar aprotic solvents for the formation of high molecular weight polyamides. The high reactivity of the N-acyl-2-benzothiazolones was discussed in relation to excellent leaving nature and intramolecular general base catalysis of the benzothiazolone moiety.     

Synthesis of polyamides from active 4,4′-diacylbis-2-aryl-1,3,4-oxadiazoline-5-thiones and -ones and diamines under mild conditions

New active bisamides, 4,4′ -diacylbis-2-aryl-1,3,4-oxadiazoline-5-thiones and -ones having various electron accepting groups in the oxadiazoline units were synthesized, and their reactivities toward diamines were investigated. The polycondensation reactions of the bisamides derived from 2-aryl-1,3,4-oxadiazoline-5-thiones with both aliphatic and aromatic diamines occurred rapidly even at room temperature to form high-molecular-weight polyamides in quantitative yields. The reactivities of the bisamides having electron accepting groups such as p-chloro and p-nitro groups, particularly p-nitro groups, toward diamines were much higher than that of the corresponding bisamide having no such group. It was also found that reaction conditions such as solvent, monomer concentration, and temperature had a strong influence on the molecular weight of the resulting polyamides. Aminolysis of several benzoyl derivatives of 2-aryl-1,3,4-oxadiazoline-5-thiones and -ones was also carried out as a model reaction, and the effect of electron accepting groups on the reactivity of these compounds was discussed.     

Direct polycondensation with tosyl chloride in pyridine by formamide catalyzed alcoholysis

The reaction with tosyl chloride was significantly promoted by controlling alcoholysis with bisphenols in the presence of catalytic amounts of formamides to give aromatic polyesters with high molecular weights from aromatic dicarboxylic acids and bisphenols. Mechanistic features of the reaction were studied by use of various formamides and other arylsulfonyl chlorides, as well as by varying the addition mode of bisphenols and changing the relative amount of formamide. The reaction was successfully applied to the preparation of aromatic polyesteramides with high molecular weights from aromatic dicarboxylic acids, bisphenols, and diamines, but with limited success to that of polyamides.     

Synthesis and characterization of aromatic polyamides from 1,1-bis(4-aminophenyl)-2,2-diphenylethylene and aromatic diacid chlorides

Novel, soluble aromatic polyamides and copolyamides containing tetraphenylethylene units were prepared by the low temperature solution polycondensation of 1,1-bis(4-aminophenyl)-2,2-diphenylethylene and aromatic diamines with various aromatic diacid chlorides. Highmolecular-weight polyamides having inherent viscosities of 0.6–1.5 dL/g and number-average molecular weight above 21000 were obtained quantitatively. These polymers were readily soluble in various solvents such as N-methyl-2-pyrrolidone, N,N-dimethylacetamide (DMAc), and dimethyl sulfoxide and gave pale yellow, transparent, flexible films by casting from DMAc solution. The polymers had glass transition temperatures between 290 and 340°C, and started to lose weight around 400°C, with 10% weight loss being recorded at about 470°C in air.     

Polymers containing polyhedral borane rings I. Condensation polymers

The preparation and properties of a unique new class of polymers containing polyhedral borane cages as part of the backbone polymer chain are described. The synthesis of polyamides, polyesters, polyureas, and polyurethanes proceeds from suitably chosen B₁₀ and B₁₂ polyhedral borane dicarbonyls, diols, and diisocyanates by typical condensation polymer techniques. Each complementary monomer may be a borane compound, but more often higher molecular weight products are provided when one monomer is a conventional organic reagent such as an aromatic diisocyanate. The polyamides prepared from 1, 12-B₁₂H₁₀(CO)₂ and organic diamines were crystalline and soluble, but molecular weight were limited because the amidation reaction was reversible and/or the amide linkage could be split by nucleophilic attack by some solvents. The polyurethanes prepared from Na₂B₁₂H₁₀(OH)₂ and aromatic diisocyanates were high molecular weight and relatively more stable. Clear, colorless, tough films were prepared. These polymers were soluble in many polar solvents and exhibited typical polyelectrolyte behavior.     

Influence of monofunctional reactants on the physical properties of dimer acid‐based polyamides

Dimer acid‐based polyamides were synthesized by condensation polymerization in the absence and presence of monofunctional reactants. Acetic acid, oleic acid and propyl amine were used as monofunctional reactants. The influences of the equivalent percentage (E%) and type of monofunctional reactant on the physical properties of dimer acid‐based polyamides such as glass transition temperature (T_g), melting point (T_m), heat of fusion (ΔH), degree of polymerization (DP), number average molecular weight (M_n), and kinematic viscosity were investigated. The molecular weight and viscosity of dimer acid‐based polyamides decreased with the increase in equivalent percentage of monofunctional reactant. Differential scanning calorimetry (DSC) studies showed that acetic acid and propyl amine had higher effect on the thermal properties of polyamides than that of oleic acid. In the case of polyamides prepared in the presence of acetic acid, the values of T_g, T_m, and ΔH of the polyamides increased remarkably with the increase in acetic acid content. On the contrary, propyl amine had a decreasing effect on the values of T_g, T_m, and ΔH of the polyamides. Incorporation of oleic acid into the polymer structure had no significant effect on the values of T_g and T_m of the dimer acid‐based polyamides. Copyright © 2006 John Wiley & Sons, Ltd.     

High-Energy Phosphonium Compounds and Their Application to Polymer Synthesis

High-energy phosphonium compounds, the N-phosphonium salts of pyridines, were prepared by the oxidation of phosphorous acid and its esters with mercuric salts or halogens in pyridines, or by a hydrolysis-dehydration reaction of diphenyl and triaryl phosphites or phosphonites. These salts are very reactive to nucleophiles, activating carboxyl, amino, or hydroxyl compounds via the corresponding N-phosphonium salts to yield carboxylic amides and esters in high yields on further aminolysis, alcoholysis, and acidolysis. These reactions, especially the hydrolysis-dehydration reactions with phosphites, were successfully extended to the direct polycondensation reaction of dicarboxylic acids with diamines, of free α-amino acids or dipeptides, and of carbon dioxide and disulfide with diamines under mild conditions, yielding linear polymers of high molecular weight (polyamides, polypeptides, polyureas, and polythioureas).