Supercritical fluid extraction of cynaropicrin and 20-hydroxyecdysone from Leuzea carthamoides DC

Leuzea carthamoides is an adaptogenic plant containing biologically active compounds as ecdysteroids and guaianolide-type sesquiterpene lactones, conventionally extracted from the plant with ethanol. It may be a potential source of the mentioned natural compounds. Ethanol-modified near-critical CO(2) was used as selective solvent with the aim to increase the level of 20-hydroxyecdysone in the extract from L. carthamoides roots and to remove selectively cynaropicrin, a sesquiterpene lactone of bitter taste, from the leaves. The extraction conditions were varied (pressure 20-28 MPa, temperature 40-60 degrees C, ethanol concentration in the solvent 0-7.1%) and the extraction yield and extract composition were compared with the results of ethanolic extraction. The supercritical fluid extraction (SFE) from finely powdered plant was controlled by phase equilibrium. Cynaropicrin was quantitatively removed from the leaves where 89% of 20-hydroxyecdysone was retained. The extraction yield of 20-hydroxyecdysone from roots with ethanol-modified CO(2 )was lower by 30% than with ethanol but its concentration in the extract was higher by 67%.     

Feasibility of on-line supercritical fluid extraction of steroids from aqueous-based matrices with analysis via gas chromatography-mass spectrometry

The solubility of testosterone, boldenone, androstenone, etiocholanolone, and epitestosterone are measured in pure supercritical CO2. Testosterone exhibited the highest solubility in supercritical CO2. The solubility of all steroids except epitestosterone increased by one order of magnitude with increasing pressure from 100 to 400 atm. Epitestosterone had the lowest solubility in supercritical CO2 and its solubility was not affected by pressure. The extraction efficiency of steroids from an aqueous saline environment exceeded 95%. Because of the partial solubility of water in supercritical CO2, the addition of a moisture trap after the aqueous vessel is necessary to prevent the plugging and deterioration of the gas chromatographic (GC) column. It is demonstrated that on-line supercritical fluid extraction-GC-mass spectrometry is feasible for the quantitative extraction and analysis of steroids from both saline and urine solutions. However, it is determined that the adsorbent vessel filled with Hydromatrix is not sufficient to trap all the moisture, and after 3 to 4 extractions, the GC column efficiency lowered.     

A two-step supercritical fluid extraction of polycyclic aromatic hydrocarbons from roadside soil samples

A two-step procedure for the supercritical fluid extraction (SFE) of polycyclic aromatic hydrocarbons from soil samples was developed. The procedure consists of a static supercritical fluid treatment in a closed extraction cell at a high temperature (T=250 or 340degreesC for 20 min) and an SFE with a solvent trapping. During the static phase, the sample is exposed to a supercritical organic solvent (methanol, toluene, dichloromethane, ACN, acetone, and hexane). The solvent penetrates particles of the matrix to substitute strongly bonded molecules and dissolves the analytes in the supercritical phase. At ambient temperature, supercritical fluids became liquid and lost their solvation abilities. Most of the analytes condense on the surface of the particles or on the extraction cell walls without forming strong bonds or penetrating deep into the matrix. Thus, the pretreatment liberates the analytes and they behave similar to those in freshly spiked samples. The common SFE with toluene-modified CO2 as an extraction fluid follows the static phase. With the use of the most suitable extraction phases (toluene, ACN), the extraction efficiency of the combined procedure is much higher (approximately100%). The results of the combined procedure are compared to the SFE procedure of the same untreated sample (difference less than 5%) and to the Soxhlet extraction. The extracts were analyzed using a GC with the flame ionization detection.     

Feasibility study of online supercritical fluid extraction-liquid chromatography-UV absorbance-mass spectrometry for the determination of proanthocyanidins in grape seeds

Online coupling of supercritical fluid extraction (SFE) with liquid chromatography (LC)-UV absorbance-electrospray ionization (ESI)-mass spectrometry (MS) is evaluated for the determination of proanthocyanidins in grape seeds. The solid-phase intermediate trap is optimized in order to enhance the collection efficiency for the extracted polar components. Pure supercritical CO2 is used first to remove the oil in the seeds. Then methanol-modified CO2 is used to remove the polar components (e.g., phenolic compounds). Catechin and epicatechin (90%) are extracted out of the de-oiled after 240 min with 40% methanol as a modifier. Both singly-linked (B-type) and doubly-linked (A-type) procyanidins are identified by LC-ESI-MS, as well as their galloylated derivatives. The hyphenated system combines the extraction, separation, and detection in series. The experimental design minimizes the chance of analyte oxidation, degradation, and contamination. The traditional off-line SFE-LC method is also studied for comparison with the online method. Both advantages and disadvantages are observed for the online mode.     

超临界流体萃取法对有机锡化合物的选择性萃取

 研究了用超临界流体萃取法直接从脂肪基质的固体样品（大豆粉）中选择性地萃取有机锡化合物的方法。模拟试样萃取结果表明：用较低压力和较高温度的超临界态ＣＯ２作流动相时，有机锡达到最大萃取率，而脂肪类物质仅被少量萃取，从而消除了脂肪类物质对超临界流体色谱法测定有机锡的干扰。     

Supercritical fluid extraction of organic and inorganic mercury from solid materials

Mercuric ions (Hg(2+)) can be extracted from solid samples (cellulose matrix) using methanol modified supercritical CO(2) containing the fluorinated chelating agent lithium bis(trifluoroethyl)dithiocarbamate (LiFDDC). Methylmercuric chloride (CH(3)HgCl) and dimethylmercury [(CH(3))(2)Hg] can be extracted by supercritical CO(2) without chelating agent and modifier. The solubility of Hg(FDDC)(2) in supercritical CO(2) has been determined to be 5 x 10(-3)M at 5O degrees C and 150 atm, which is about 3 orders of magnitude greater than that of the non-fluorinated analogue Hg(DDC)(2). Use of methanol (5%)-modified CO(2) further enhances the solubility of Hg(FDDC)(2) by a factor of 2.4. A small amount of water added to the sample matrix tends to facilitate the extraction of Hg(FDDC)(2) and CH(3)HgCl. Potential applications of this in situ chelation-supercritical fluid extraction method for the preconcentration of mercury species and treatment of mercury contaminated wastes are discussed.     

Optimization of supercritical fluid extraction by carbon dioxide with organic modifiers of polycyclic aromatic hydrocarbons from urban particulate matter

The main advantages of using supercritical fluids for the extractions of organic pollutants from environmental matrix is that they are inexpensive, contaminant free, and less costly to dispose safely than organic solvents. In this work, a series of extraction experiments were carried out using CO2 as supercritical fluid on a certified sample of "Urban dust" (NIST S.R.M. 1649a) to optimize the analytical parameters with the aim of investigating the extraction limit of organic pollutant by using an almost "organic solvent-free" technique. The certified sample contains small concentrations of several organic pollutants, as PAH and PCB. The initial tests of extraction were carried out with only CO2 in supercritical phase, by maintaining the temperature at 50 degrees C and 80 degrees C and by making the pressure vary between 230 bar and 600 bar. The effect of three organic modifiers (methanol, n-hexane and toluene), added at 5% in volume, has been considered. The yield of recovery has been estimated for anthracene, fluoranthene, chrysene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene by GC-MS according to the increasing molecular weight.     

Determination of vitamins A and E in milk powder using supercritical fluid extraction for sample clean-up

A method for the analysis of the natural contents of vitamins A and E in milk powder has been developed. The method utilises supercritical fluid extraction, a miniaturised alkaline saponification procedure and reversed-phase HPLC with UV detection. Modifications of the sample matrix, combinations of static and dynamic modes of extraction and effects of changes in extraction parameters such as temperature, flow-rate, time, collection solvent and collection temperature were studied to optimise the extraction efficiency and selectivity. Supercritical CO2 at 80 degrees C and 37 MPa, modified with 5% methanol and pumped at a flow-rate of 1.0 ml/min, gave recoveries of 99 and 96% for vitamins A and E, respectively, using a 15 min static followed by a 15 min dynamic extraction. The measurements gave a within-day RSD of 4% for both vitamin A and E, and between-day RSDs of 4 and 8% for vitamins A and E, respectively.     

超临界二氧化碳萃取秋水仙碱（英文）

 利用超临界二氧化碳对秋水仙块根（经粉碎）中的秋水仙碱进行了萃取,采用高效液相色谱法对萃取出的秋水仙碱的质量分数进行了测定。实验选择40℃20～40MPa作为超临界苹取的操作条件,采用体积分数为95％的乙醇在索氏提取器中对样品进行了对比苹取实验。结果表明:不加浸泡剂进行浸泡处理的样品中的秋水仙碱很难被超临界二氧化碳萃取,在40℃,35MPa条件下,消耗1．28mol的二氧化碳只得到3％的萃取率。加入极少量的有机溶剂浸泡处理样品15min后再进行超临界萃取,可以极大程度地提高秋水仙碱的萃取率。     

Thermodynamic and kinetic models for the extraction of essential oil from savory and polycyclic aromatic hydrocarbons from soil with hot (subcritical) water and supercritical CO2

Mechanisms that control the extraction rates of essential oil from savory (Satureja hortensis) and polycyclic aromatic hydrocarbons (PAHs) from historically-contaminated soil with hot water and supercritical carbon dioxide were studied. The extraction curves at different solvent flow-rates were used to determine whether the extractions were limited primarily by the near equilibrium partitioning of the analyte between the matrix and solvent (i.e. partitioning thermodynamics, or the "elution" step) or by the rate of analyte desorption from the matrix (i.e. kinetics, or the "initial desorption" step). Two simple models were applied to describe the extraction profiles obtained with hot water and with supercritical CO2: (1) a model based solely on the thermodynamic distribution coefficient KD, which assumes that analyte desorption from the matrix is rapid compared to elution. and (2) a two-site kinetic model which assumes that the extraction rate is limited by the analyte desorption rate from the matrix, and is not limited by the thermodynamic (KD) partitioning that occurs during elution. For hot water extraction, the thermodynamic elution of analytes from the matrix was the prevailing mechanism as evidenced by the fact that extraction rates increased proportionally with the hot water flow-rate. This was also confirmed by the fact that simple removal calculations based on a single KD (for each essential oil compound) gave good fits to experimental data for flow-rates from 0.25 to 4 ml/min. In contrast, supercritical CO2 extraction showed only minimal dependence on flow-rate, and the simple KD model could only describe the initial 20-50% of the extraction. However, a simple two-site kinetic model gave a good fit for all CO2 flow-rates tested. The results of these investigations demonstrated that very simple models can be used to determine and describe extractions which are limited primarily by partitioning thermodynamics, or primarily by desorption kinetics. Furthermore, these results show that the time required for the recovery of essential oil from savory with hot water can be minimized by increasing flow-rate, with little change in the total volume of water required. In contrast, raising the flow-rate of supercritical CO2 has little effect on the mass of essential oils recovered per unit of time, indicating that optimal recovery of these compounds with supercritical CO2 (amount recovered for the lowest amount of CO2) requires longer extraction times rather than faster flow-rates.     

The use of supercritical fluid extraction for the determination of steroids in animal tissues.

A multi-analyte, multi-matrix method was developed for the routine determination of steroids in animal tissues (skin, meat and fat). After addition of internal standards and sample pre-treatment, the analytes of interest were extracted from the matrix with unmodified supercritical CO2 and trapped directly on an alumina sorbent placed in the extraction vessel (in-line trapping under supercritical conditions). After extraction, alkaline hydrolysis was performed and the analytes were derivatised. The samples were then analysed by gas chromatography-mass spectrometry. The limit of detection for the different matrix-analyte combinations was 2 micrograms kg-1 (for melengestrol acetate 5 micrograms kg-1), the repeatability ranged from 4 to 42% (n = 9) and the reproducibility ranged from 2 to 39% (n = 3).     

Comparisons of soxhlet extraction, pressurized liquid extraction, supercritical fluid extraction and subcritical water extraction for environmental solids: recovery, selectivity and effects on sample matrix

Extractions of a polycyclic aromatic hydrocarbon (PAH)-contaminated soil from a former manufactured gas plant site were performed with a Soxhlet apparatus (18 h), by pressurized liquid extraction (PLE) (50 min at 100 degrees C), supercritical fluid extraction (SFE) (1 h at 150 degrees C with pure CO2), and subcritical water (1 h at 250 degrees C, or 30 min at 300 degrees C). Although minor differences in recoveries for some PAHs resulted from the different methods, quantitative agreement between all of the methods was generally good. However, the extract quality differed greatly. The organic solvent extracts (Soxhlet and PLE) were much darker, while the extracts from subcritical water (collected in toluene) were orange, and the extracts from SFE (collected in CH2Cl2) were light yellow. The organic solvent extracts also yielded more artifact peaks in the gas chromatography (GC)-mass spectrometry and GC-flame ionization detection chromatograms, especially compared to supercritical CO2. Based on elemental analysis (carbon and nitrogen) of the soil residues after each extraction, subcritical water, PLE, and Soxhlet extraction had poor selectivity for PAHs versus bulk soil organic matter (approximately 1/4 to 1/3 of the bulk soil organic matter was extracted along with the PAHs), while SFE with pure CO2 removed only 8% of the bulk organic matrix. Selectivities for different compound classes also vary with extraction method. Extraction of urban air particulate matter with organic solvents yields very high concentrations of n- and branched alkanes (approximately C18 to C30) from diesel exhaust as well as lower levels of PAHs, and no selectivity between the bulk alkanes and PAHs is obtained during organic solvent extraction. Some moderate selectivity with supercritical CO2 can be achieved by first extracting the bulk alkanes at mild conditions, followed by stronger conditions to extract the remaining PAHs, i.e., the least polar organics are the easiest organics to extract with pure CO2. In direct contrast, subcritical water prefers the more polar analytes, i.e., PAHs were efficiently extracted from urban air particulates at 250 degrees C, with little or no extraction of the alkanes. Finally, recent work has demonstrated that many pollutant molecules become "sequestered" as they age for decades in the environment (i.e., more tightly bound to soil particles and less available to organisms or transport). Therefore, it may be more important for an extraction method to only recover pollutant molecules that are environmentally-relevant, rather than the conventional attempts to extract all pollutant molecules regardless of how tightly bound they are to the soil or sediment matrix. Initial work comparing SFE extraction behavior using mild to strong conditions with bioremediation behavior of PAHs shows great promise to develop extraction methodology to measure environmentally-relevant concentrations of pollutants in addition to their total concentrations.     

Supercritical fluid extraction of catechins from Cratoxylum prunifolium dyer and subsequent purification by high-speed counter-current chromatography

Supercritical fluid extraction of tea catechins including epigallocatechin-3-O-gallate (EGCG) and epicatechin-3-O-gallate (ECG) from Cratoxylum prunifolium Dyer was performed. The optimization of parameters was carried out using an analytical-scale supercritical fluid extraction (SFE) system designed in our laboratory. Then the extraction was scaled up by 100 times using a preparative SFE system under a set of optimized conditions of 40 degrees C, 25 MPa and modified CO2 with 80% ethanol aqueous solution. The combined yield of EGCG and ECG reached about 1 mg per 1 g of tea leaves where the solubility was near 1.4 x 10(-4) mass fraction of CO2 fluid. EGCG and ECG of high purity (>98%) were obtained from the crude preparative extract by high-speed counter-current chromatography.     

Strategies for supercritical fluid extraction of hyoscyamine and scopolamine salts using basified modifiers

The supercritical fluid extraction behaviors of hyoscyamine and scopolamine were investigated and found to be highly dependent upon the chemical nature of the compounds. Free bases of hyoscyamine and scopolamine were freely soluble in supercritical CO2 with increasing temperature and pressure; however, the salts of these alkaloids were not soluble under any experimental conditions. It was found that alkaline modifiers such as methanol basified with diethylamine could enhance the solubilities and extraction yields of these alkaloids from plant matrices as compared to other modifiers.     

Comparative analysis of the oil and supercritical CO(2) extract of Cymbopogon citratus Stapf

Dried and ground leaves of lemon grass (Cymbopogon citratus Stapf.) were used as a matrix for supercritical extraction of essential oil with CO(2). The objective of this study was to analyze the influence of pressure on the supercritical extraction. A series of experiments were carried out, for 360 min, at 50 degrees C and at different pressures: 90, 100, 110 and 120 bar. Extraction conditions were chosen to maximize citral content in the extract oil. The collected extracts were analysed by GC-MS and their composition was compared with that of the essential oil isolated by hydrodistillation and by steam distillation. At higher solvent density the extract aspect changes passing from a characteristic yellow essential oil to yellowish semi-solid mass because of the extraction of high molecular mass compounds. The optimum conditions for citral extraction were 90 bar and 50 degrees C, at these conditions citral represent more than 68% of the essential oil and the extraction yield was 0.65% while the yield obtained from hydrodistillation was 0.43% with a content of citral of 73%.     

Online recovery of radiocesium from soil,cellulose and plant samples by supercritical fluid extraction employing crown ethers and calix-crown derivatives as extractants

Two crown ethers (CEs) viz. dibenzo18crown6, and dibenzo12crown7 and three calix-crown derivatives viz. (octyloxy)calix[4]arene-mono-crown-6 (CMC), calix[4]arene-bis(o-benzocrown-6) (CBC), and calix[4]arene-bis(naphthocrown-6) (CNC) were evaluated for the recovery of ¹³⁷Cs from synthetic soil, cellulose (tissue paper), and plant samples by supercritical fluid extraction (SFE) route. CEs showed poor extraction of ¹³⁷Cs from soil matrix. SFE experiments using 1 × 10^?3 M solutions of CMC, CBC and CNC in acetonitrile at 3 M HNO₃ as modifiers displayed better extraction of ¹³⁷Cs, viz. 21(±2) % (CMC), 16.5(±3) % (CBC), and 4(±1) % (CNC). It was not possible to recover ¹³⁷Cs quantitatively from soil matrix. The inefficient extraction of ¹³⁷Cs from soil matrix was attributed to its incorporation into the interstitial sites. Experiments on tissue papers using CMC showed near quantitative ¹³⁷Cs recovery. On the other hand, recovery from plant samples varied between 50(±5) % (for stems) and 75(±5) % (for leaves).     

Supercritical fluid extraction of nylon 6,6 oligomers and their characterization via liquid chromatography coupled with mass spectrometry.

This research extends previous studies regarding the application of supercritical fluid extraction (SFE) for the analysis of oligomers from nylon 6,6 fibers. The effects of CO2 pressure, extraction temperature, CO2-modifier percentage, static extraction time and dynamic extraction time on the SFE efficiency of nylon 6,6 oligomers were examined. Results from the SFE methods for oligomer extractions were compared to results from conventional solvent extraction. The extracted oligomers were identified by high-performance liquid chromatography (HPLC) with coupled on-line atmospheric pressure chemical ionization mass spectrometry and HPLC fractionation coupled with off-line liquid secondary ion mass spectrometry.     

Solubility of metal chelates and their extraction from an aqueous environment via supercritical CO(2)

Solubility of nickel(II), copper(II), and chromium(III) hexafluoroacetylacetone and chromium(III) acetylacetone chelates was measured in supercritical CO(2) at two different pressures (200 and 400 atm) and 60 degrees C. Solubility of fluorinated acetylacetone chelates was at least an order of magnitude higher than the non-fluorinated complexes. These pre-formed metal chelates as well metal diethyldithiocarbamate (DDC) and metal bis(trifluoroethyl)dithiocarbamate (FDDC) have also been extracted from aqueous environment using pure supercritical CO(2). It was demonstrated that metal HFA chelates while exhibiting higher solubility in supercritical CO(2) compared with metal FDDC chelates, exhibited lower extraction efficiency using the same extraction conditions. This behavior of metal HFA chelates is related to their stability in an aqueous environment. Direct extraction of Ni(+2) and Cu(+2) from an aqueous matrix was also achieved via in-situ chelation using diethyldithiocarbamate and bis(trifluoroethyl)dithiocarbamate as the ligands. Bis(trifluoroethyl)dithiocarbamate proved to be a more effective ligand for direct extraction of metal ions from aqueous environment using supercritical CO(2).     

Extraction of cloransulam-methyl from soil with subcritical water and supercritical CO2

Cloransulam-methyl was extracted from soil samples with supercritical CO2, subcritical water and conventional organic solvents. Supercritical CO2 was less efficient than conventional organic solvents; polarity modifiers had no impact on extraction efficiency. Extraction with supercritical CO2 exhibited a strong temperature dependence. Water was as effective as strong organic solvents for the extraction of cloransulam-methyl; however cloransulam-methyl hydrolyzed when extracted at 150 degrees C. Extraction temperature was the most important variable in increasing the efficiency and rate of extraction, while extraction pressure was not a significant variable.     

Combined analysis by GC (RI), GC-MS and 13C NMR of the supercritical fluid extract of Abies alba twigs

Two samples (leaves and twigs) of Abies alba Miller from Corsica were extracted using supercritical CO2 and their chemical compositions were compared with those of the essential oils obtained from the same batch of plant material. In total 45 components were identified using combined analysis by GC (RI), GC-MS and 13C NMR. It was observed that the contents of monoterpenes (mainly represented by limonene, alpha-pinene and camphene) were significantly lower in the supercritical fluid extract (SFE) than in the essential oil (EO). Conversely, the proportions of sesquiterpenes were much higher in CO2 extracts than in essential oils (around 30% vs 4%). Cis-abienol, a diterpene alcohol, was identified only in SFE, and the proportions of this constituent (7.5% and 17.3%) were determined using quantitative 13C NMR since it was under estimated using the standard conditions of GC.