Fabrication of Bismuth/Multi-walled Carbon Nanotube Composite Modified Glassy Carbon Electrode for Determination of Cobalt

A bismuth/multi‐walled carbon nanotube (Bi/MWNT) composite modified electrode for determination of cobalt by differential pulse adsorptive cathodic stripping voltammetry is described. The electrode is fabricated by potentiostatic pre‐plating bismuth film on an MWNT modified glassy carbon (GC) electrode. The Bi/MWNT composite modified electrode exhibits enhanced sensitivity for cobalt detection as compared with the bare GC, MWNT modified and bismuth film electrodes. Numerous key experimental parameters have been examined for optimum analytical performance of the proposed electrode. With an adsorptive accumulation of the Co(II)‐dimethylglyoxime complex at ?0.8 V for 200 s, the reduction peak current is proportional to the concentration of cobalt in the range of 4.0×10^?10?1.0×10^?7 mol/L with a lower detection limit of 8.1×10^?11 mol/L. The proposed method has been applied successfully to cobalt determination in seawater and lake water samples.     

Catalytic Adsorptive Stripping Voltammetry of Cobalt in the Presence of Nitrite at an In Situ Plated Bismuth Film Electrode

For the first time an in situ plated bismuth film electrode has been applied to catalytic adsorptive stripping voltammetry of cobalt in the presence of nitrite. At optimised conditions bismuth film was plated before each measurement for 30 s at ?1.0 V from a sample solution with the added supporting electrolyte and Bi(III) in the form of its complex with tartrate. The calibration graph for Co(II) for an accumulation time of 120 s was linear from 5×10^?10 to 1×10^?8 mol L^?1. The detection limit was 1.1×10^?10 mol L^?1. The proposed procedure was applied for Co(II) determination in certified water reference material.     

High Sensitivity and Reproducibility of a Bismuth/Poly(bromocresol purple) Film Modified Glassy Carbon Electrode for Determination of Trace Amount of Cadmium by Differential Pulse Anodic Stripping Voltammetry

This work described a novel type of bismuth/poly(bromocresol purple) film modified glassy carbon electrode (denoted as Bi/Poly(BCP)/GCE) for anodic stripping analysis of trace Cd²⁺. The Bi/Poly(BCP)/GCE was fabricated in situ by depositing simultaneously bismuth and cadmium by reduction at ?1.20 V on the poly(BCP) film using a differential pulse voltammetry. Under the optimum conditions, the anodic stripping peak current response increased linearly with the Cd²⁺ concentrations in a range of 2.0×10^?8–1.0×10^?7 M and 1.0×10^?7–6.0×10^?6 M in 0.1 M NaAc‐HAc buffer solution (pH 5.0) with the detection limit of 6.5×10^?9 M (S/N=3). The Bi/poly(BCP)/GCE performed good reproducibility and high sensitivity. Finally, this proposed method was successfully applied to determine the concentration of Cd²⁺ in water samples.     

Double Deposition and Stripping Steps for Trace Determination of Au(III) Using Anodic Stripping Voltammetry

A new way of decreasing the detection limit ‐ double deposition and stripping steps was proposed to determine trace amounts of gold(III) by anodic stripping voltammetry. Two carbon composite electrodes that differed drastically in their surface areas were used for the measurements. The calibration graph was linear from 1×10^?9 to 1×10^?8 mol L^?1 following deposition time of 300 s at the first and the second electrode. The detection limit was found to be 2.3×10^?10 and 1.4×10^?11 mol L^?1 for deposition time 600 and 2400 s, respectively. It is the lowest detection limit obtained so far for gold(III) determination in stripping voltammetry.     

Simultaneous Determination of Iron and Copper in Ethanol Fuel Using Nafion/Carbon Nanotubes Electrode

This work presents the analytical method development for iron and copper determination in ethanol fuel. This method was developed using stripping voltammetry with a glassy carbon electrode modified with Nafion/Carbon‐nanotubes. With linear sweep stripping voltammetry was achieved a limit of detection of 7.1×10^?7 mol L^?1 for Fe³⁺ and 5.1×10^?8 mol L^?1 for Cu²⁺. The amperometric sensitivities were 2.0×10⁶ µA mol^?1 L for Fe³⁺ and 2.8×10⁷ µA mol^?1 L for Cu²⁺. The recovery study showed that the method has good accuracy and repeatability, with recovery of 108 and 103 % for Fe³⁺ and Cu²⁺ respectively.     

Direct determination of bismuth(III) in sea water by square-wave anodic stripping voltammetry at a glassy-carbon rotating-disk electrode

A method for the determination of bismuth(III) in untreated sea water at its natural pH of 8.1 is described. A bare glassy-carbon rotating-disk electrode is preconditioned by placing in the sample at an applied potential of ?0.8 V vs. Ag/AgCl for 20 min; after stripping to ?0.4 V, bismuth is accumulated for 5 min at ?0.8 V and finally stripped in the square-wave mode. The bismuth peak appears at ca. + 0.10 V vs. Ag/AgCl; peak height is linearly related to concentration up to 2×10^?10 mol dm^?3. The method is highly selective for bismuth. The concentration of Bi(III) in the investigated sample was (6±1)×10^?11 mol dm^?3, or 12±2 ng dm^?3. The different types of response obtained are discussed.     

Determination of Atrazine in Natural Water Samples by Differential Pulse Adsorptive Stripping Voltammetry Using a Bismuth Film Electrode

A new method using differential pulse adsorptive stripping voltammetry for the determination of atrazine (ATZ) in natural water samples using a bismuth film electrode (BiFE) is proposed. The calibration curve was linear in the atrazine concentration range from 6.7×10^?7 to 2.0×10^?5 mol L^?1, with a limit of detection (LOD) of 1.4×10^?7 mol L^?1. The proposed electrode was applied for atrazine determination with satisfactory results compared with a high‐performance liquid chromatography method (HPLC).     

Electrochemical Behavior of 6-Mercapto-Purine at Hanging Copper Amalgam Dropping Electrode and Its Trace Determination by Differential Pulse Adsorption Cathodic Stripping Voltammetry

Abstract

The electrochemical behavior of 6-MP was studied by cyclic voltammetry at a hanging copper amalgam dropping electrode (HCADE). It was found that 6-MP could form a complex with the Cu(II) stripped from the HCADE, showing a new peak at ?0.19V in the medium of 0.1mol/L LiClO₄-0.5mol/L HClO₄ solution. The mechanism of the reaction was proposed. This new peak was sensitive and could be used for the determination of trace 6-MP by differential pulse adsorption cathodic stripping voltammetry (DPAdCSV). The linear range was from 3.6×10^?10 to 5.3×10^?6 mol/L, and the detection limit was about 1.2×10^?10 mol/L (S/N=3). The method was also successfully applied to the determination of 6-MP in pharmaceutical tablets.     

Renewable Ceramic (TiN) Ring Electrode in Stripping Voltammetry. Determination of Pb(II) Without Removal of Oxygen

Characteristic features of the process of Pb(II) reduction and oxidation at a renewable ceramic ring electrode (RCRE) were studied by stripping voltammetry. The main constituents of the RCRE are: a specially constructed TiN ring electrode, a silver sheet used as silver counter/quasi‐reference electrode and a silicon O‐ring are fastened together in a polypropylene body. The renovation of this electrode is carried out through mechanical removal of solid contaminants and electrochemical activation in the electrolyte which fills the RCRE body. The optimal measurement conditions, composition of supporting electrolyte and procedures of the electrode activation were selected. The measurements were carried out from nondeaerated solutions. As shown on selected examples, RCRE exhibits good performance in underpotential deposition stripping voltammetry (UPD‐SV) applied for the determination of lead(II) in synthetic solutions with and without surfactants and in certified reference materials. The peak current is proportional to the concentration of lead(II) over the range 2×10^?9–1×10^?7 mol L^?1, with a 3σ detection limit of 1×10^?9 mol L^?1 with an accumulation time of 30 s. The obtained results showed good reproducibility, (RSD=2–5%; n=5) and reliability.     

Voltammetric Determination of Selected Aminoquinolines Using Carbon Paste Electrode

Optimum conditions have been found for voltammetric determination of mutagenic 5‐aminoquinoline, 6‐aminoquinoline and 3‐aminoquinoline by differential pulse voltammetry and adsorptive stripping differential pulse voltammetry on carbon paste electrode. The lowest limits of determination were found for adsorptive stripping differential pulse voltammetry in 0.1 mol dm^?3 H₃PO₄ (5×10^?7 mol dm^?3 , 1×10^?7 mol dm^?3, and 1×10^?7 mol dm^?3 for 5‐aminoquinoline, 6‐aminoquinoline and 3‐aminoquinoline, respectively). The possibility to determine mixtures of 8‐aminoquinoline with 3‐aminoquinoline or 5‐aminoquinoline or 6‐aminoquinoline, and mixtures of 5‐aminoquinoline with 3‐aminoquinoline or 6‐aminoquinoline by differential pulse voltammetry was verified. Binary mixtures of 8‐aminoquinoline with 3‐aminoquinoline or 6‐aminoquinoline, and of 3‐aminoquinoline with 5‐aminoquinoline could be successfully analyzed.     

Sensitive and Simple Electrochemical Detection of Lead(II) with Carbon Ionic Liquid Electrode

In this paper a carbon ionic liquid electrode (CILE) was fabricated by using ionic liquid 1‐ethyl‐3‐methylimidazolium ethylsulphate ([EMIM]EtOSO₃) as the modifier and further used as the working electrode for the sensitive anodic stripping voltammetric detection of Pb²⁺. The characteristics of the CILE were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). In pH 4.5 NaAc‐HAc buffer Pb²⁺ was accumulated on the surface of CILE due to the extraction effect of IL and reduced at a negative potential (‐1.20 V). Then the reduced Pb was oxidized by differential pulse anodic stripping voltammetry with an obvious stripping peak appeared at ?0.67 V. Under the optimal conditions Pb²⁺ could be detected in the concentration range from 1.0 × 10^?8 mol/L to 1.0 × 10^?6 mol/L with the linear regression equation as I_p(μA) = ?0.103 C (μmol/L) + 0.0376 (γ = 0.999) and the detection limit as 3.0 × l0^?9 mol/L (3σ). Interferences from other metal ions were investigated and Cd²⁺ could be simultaneously detected in the mixture solution. The proposed method was further applied to the trace levels of Pb²⁺ detection in water samples with satisfactory results.     

Determination of Blasticidin S in Spiked Rice Using SW Voltammetry with a Renewable Silver Amalgam Film Electrode

Blasticidin S (BS) was determined in spiked rice samples by square wave voltammetry (SWV) and square wave stripping voltammetry (SWSV) using a cyclic renewable silver amalgam film electrode (Hg(Ag)FE). It was found that the compound can act as an electrocatalyst. In Britton? Robinson buffer at pH 7.0 a signal connected with the hydrogen evolution reaction was detected at ?1.2 V versus Ag/AgCl. Validation of the method was carried out. The detection and quantification limits were found to be 2.13×10^?8 mol L^?1; 7.10×10^?8 mol L^?1 for SWV and 2.65×10^?9 mol L^?1; 8.85×10^?9 mol L^?1 for SWSV, respectively.     

Determination of Antimony(III) by Differential Pulse Voltammetry Using a Gold Nanoparticle–Ionic Liquid–Graphene-Modified Selenium-Doped Carbon Paste Electrode

A simple and sensitive differential pulse stripping voltammetric method was developed for the determination of antimony(III) using a selenium-doped carbon paste electrode modified with an ionic liquid, graphene, and gold nanoparticles. The conditions, including the mass of graphene, concentration of hydrochloric acid, deposition potential, and deposition time were optimized by single-factor experiments. Under the optimal conditions, a linear equation of I_Sb(III) (µA)?=??16.9882???11.0929 c (µmol/L) (R?=?0.9965) and a detection limit of 2.7?×?10^?8?mol/L were obtained for 8.0?×?10^?8 to 4.8?×?10^?6?mol/L antimony(III). The response shows that the sensor enhances the sensitivity of antimony due to the high conductivity and large surface areas of the ionic liquid, graphene, and gold nanoparticles. This electrode may provide a new sensing platform for the determination of antimony.     

Voltammetric Determination of L‐Dopa Using a Carbon Nanotubes‐Nafion Modified Glassy Carbon Electrode

Abstract

A method for determination of L‐dopa by the adsorption stripping voltammetry (ASV) using a multiwalled carbon nanotubes (MWNTs)–Nafion modified glassy carbon electrode (GMGCE) was proposed. This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed and the anodic peak potential is ca. 0.374V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of L‐dopa in samples. There is a good linear relationship between the peak current (i_p) and L‐dopa concentration in the range of 3.5×10^?7～1.5×10^?5 mol/L, with the limit of detection 5.0×10^?8 mol/L.     

Nafion‐Modified Glassy Carbon Electrode for Trace Determination of Indium

Abstract

A new method for determination of trace indium is proposed by the adsorption stripping voltammetry (ASV) using a Nafion‐modified glassy carbon electrode (NMGCE). This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed, and the anodic peak potential is ca. ?0.548 V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of indium in water samples. There is a good linear relationship between the peak current (i_p) and indium(III) concentration in the range of 1.0×10^?9–1.0×10^?7 mol/l, and the limit of detection is 7.5×10^?10 mol/l.     

Differential Pulse Anodic Stripping Voltammetric Determination of Bismuth(III) with 1‐(2‐Pyridylazo)‐2‐naphthol and Ionic Liquid Modified Carbon Paste Electrode

In this paper 1‐(2‐pyridylazo)‐2‐naphthol (PAN) and ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) were mixed with graphite powder to get a modified carbon paste electrode (PAN‐IL‐CPE), which was further used for the sensitive determination of bismuth(III). By the co‐contribution of the formation of PAN‐Bi complex and the accumulation effect of IL, more bismuth(III) was electrodeposited on the surface of the PAN‐IL‐CPE. Then the reduced Bi was oxidized and detected by differential pulse anodic stripping voltammetry (DPASV) with the oxidation peak appeared at 0.17 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the bismuth(III) concentration in the range from 0.04 to 7.5 μmol L^?1 with the detection limit as 3.9 nmol L^?1. The proposed method was successfully applied to the stomach medicine sample detection with good recovery.     

Sequential Voltammetric Determination of Ultratrace Osmium,Ruthenium and Iridium. Application to Superficial Water

The present work, regarding the determination of ultratrace Os(VIII), Ru(III) and Ir(III) in superficial waters is an interesting example of the possibility to simultaneously, or better sequentially determine each single element in real samples by voltammetry. The method is based on the catalytic current of the Os(VIII)‐ and Ru(III)‐bromate systems by square wave voltammetry and on the Ir(III) determination by square wave catalytic adsorptive stripping voltammetry. 0.5 mol L^?1 acetate buffer pH 4.9+7.7×10^?2 mol L^?1 NaBrO₃ and 0.5 mol L^?1 acetate buffer pH 4.9+7.7×10^?2 mol L^?1 NaBrO₃+2.3×10^?5 mol L^?1 cetyltrimethylammonium bromide (CTAB) +0.2 mol L^?1 KCl were employed as the supporting electrolytes. The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR‐CRM 403 and Fresh Water NIST‐SRM 1643d. For all the elements, the accuracy, expressed as relative error e (%), was satisfactory, being lower than 6 %, while precision as repeatability, expressed as relative standard deviation, s_r (%), was generally lower than 5 %. Once set up on the standard reference materials, the analytical procedure was transferred and applied to superficial water sampled in proximity to superhighway and in the Po river mouth area.     

New Protocol for Determination of Rifampicine by Adsorptive Stripping Voltammetry

For determinations of organic compounds by adsorptive stripping voltammetry till now the same material of the electrode has been used for the accumulation and stripping steps. This paper describes a new protocol for extending the range of organic compounds, which can be determined by adsorptive stripping voltammetry. In the proposed procedure the accumulation step was performed on the electrode modified by a lead film, which assures adsorption of the studied species on the modified electrode and then the stripping step of the accumulated substance was performed on the support of the lead film electrode. As an example rifampicine was accumulated by adsorption at the lead film electrode while in the stripping step lead film and then the accumulated rifampicine were oxidized at a glassy carbon electrode. Using an acetate buffer as a supporting electrolyte a calibration graph for rifampicine in the range from 2.5×10^?10 to 1×10^?8 mol L^?1 was obtained. The detection limit for rifampicine following 60 s accumulation time was equal to 9×10^?11 mol L^?1. The obtained detection limit was comparable or lower than reported previously for other stripping voltammetric procedures. The proposed procedure was applied to rifampicine determination in pharmaceutical preparation.     

Polarographic and Voltammetric Study of the Sc(III)-Acid Chrome Blue K Complex and Determination of Trace Scandium

Abstract

A new system of polarographic adsorptive wave for determining trace scandium was proposed. In 0.2 mol/L NH₄OAc, the Sc(III)- ACBK [1,8- dihydroxy- 2- (2- hydroxy- 5- sulfo- 1- phenylazo)- 3,6- disulfo- naphthalene, called acid chrome blue K] complex emerged a sensitive adsorptive complex wave(Ep′ = -0.67V). The molar ratio of Sc(III) to ACBK in the complex was established as 1: 2 and the apparent stability constant β₂ = 2.7 × 10¹⁵. But for Y(III), the molar ratio was 1: 1 and β = 1.5 × 10⁵. Because of the particularity of Sc complex, the sensitivity and the selectivity of determination Sc are much better than that of other rare earth ions. The detection limit is 1.1 × 10^?7 mol/L for oscillopolarography and 2.0 × 10^?8 mol/L for adsorptive stripping voltammetry.     

Chemical Speciation of Antimony(III and V) in Water by Adsorptive Cathodic Stripping Voltammetry Using the 4‐(2‐Thiazolylazo) – Resorcinol

A simple adsorptive cathodic stripping voltammetry method has been developed for antimony (III and V) speciation using 4‐(2‐thiazolylazo) – resorcinol (TAR). The methodology involves controlled preconcentration at pH 5, during which antimony(III) – TAR complex is adsorbed onto a hanging mercury drop electrode followed by measuring the cathodic peak current (I_p,c) at ?0.39 V versus Ag/AgCl electrode. The plot of I_p,c versus antimony(III) concentration was linear in the range 1.35×10^?9–9.53×10^?8 mol L^?1.The LOD and LOQ for Sb(III) were found 4.06×10^?10 and 1.35×10^?9 mol L^?1, respectively. Antimony(V) species after reduction to antimony(III) with Na₂SO₃ were also determined. Analysis of antimony in environment water samples was applied satisfactorily.