Preparation of ethambutol-copper(II) complex and fabrication of PVC based membrane potentiometric sensor for copper

Copper(II) complex of ethambutol (I) was prepared and used in the fabrication of Cu(2+) selective ISE membrane. The membrane having Cu(II)-ethambutol complex (I) as electroactive material, along with sodium tetraphenylborate (NaTPB) as anion discriminator, dioctylphthalate (DOP) as plasticizer in poly(vinyl chloride) (PVC) matrix in the percentage ratio 6:2:190:200 (I:NaTPB:DOP:PVC) (w/w) gave a linear response in the concentration range 7.94x10(-6) to 1.0x10(-1) M of Cu(2+) with a slope of 29.9+/-0.2 mV per decade of activity and a fast response time of 11+/-2 s. The sensor works well in the pH range 2.1-6.3 and could be satisfactorily used in presence of 40% (v/v) methanol, ethanol and acetone and is selective for copper over a large number of cations with slight interference from Na(+) and Co(2+) if present at a level 1.5x10(-5) and 6.5x10(-5) M, respectively. It works well over a period of 6 months and can also be used as indicator electrode for the end point determination in the potentiometric titration of Cu(2+) against EDTA as well as in the determination of Cu(2+) in real samples.     

Strontium(II) sensor based on a modified calix[6]arene in PVC matrix.

5,11,17,23,29,35-Hexakis(1,1,3,3-tetramethylbutyl)-37,38,39,40,41,42-hexakis(carboxy methoxy)calix[6]arene (I) has been evaluated as an ionophore for the analysis of Sr2+. The influences of the nature of the plasticizers (DBA, CN, DOP, NPOE) and of the anion excluder (NaTPB) on the characteristics of the electrode were discussed. The best electrode was fabricated with a membrane having composition 6:150:170:3 (I:PVC:DBA:NaTPB). The response to Sr2+ was Nernstian in the range 1.9 x 10(-5) to 1.0 x 10(-1) M of Sr2+. The influence of pH has also been studied. The electrode exhibited better potential stability and had an operational lifetime of 4 months. The K(A,B)(Pot) values showed that other alkaline earth metal ions are well discriminated. The sensor has also been used as an indicator electrode in the potentiometric titration of sodium carbonate with strontium(II) ions.     

Poly(vinyl chloride)-based macrocyclic membrane sensors for magnesium

Poly(vinyl chloride)-based membranes of macrocycles 4,11-dimethyl-2,4,9,11-tetraethyl-1,5,8,12-tetraaza cyclotetradeca-1,8-diene (I) and 4,11-dioxa-2,9-dimethyl-1,5,8,12-tetraaza cyclotetradeca-1,8-diene (II) with sodium tetraphenyl borate (STB) as an anion excluder and dibutyl phthalate (DBP), dioctyl phthalate (DOP), dibutylbutyl phosphonate (DBBP) and 1-chloronaphthalene (CN) as plasticizing solvent mediators were prepared and investigated as magnesium selective electrodes. The best performance was observed having the composition (II)-PVC-STB-DBP in the ratio 2:10:1:7, which works well over a wide concentration range (1.9x10(-6) to 1.0x10(-1) M) with a Nernstian slope of 29 mV per decade of activity between pH 2.5 and 6.5. These electrodes have been found to be chemically inert showing a fast response time of 15 s and were used over a period of 3 months with good reproducibility (S=+/-0.2 mV). The selectivity coefficient values for mono-, di- and trivalent cations indicate excellent selectivity for Mg(2+) over a large number of cations. The electrodes have also been used successfully in partially non-aqueous medium and as an indicator electrode in the potentiometric titration of Mg(2+) with EDTA. Anions such as Cl(-) and SO(4)(2-) do not interfere in the working of the electrode. The practical utility of the membrane sensor has also been observed in solutions contaminated with detergents (cetyltrimethyl ammonium bromide and sodium dodecyl sulphate). Above all, the membrane sensor has been very successfully used to analyse some babyfood products and soft drinks for the determination of Mg(2+).     

Determination of SCN- in urine and saliva of smokers and non-smokers by SCN(-)-selective polymeric membrane containing a nickel(II)-azamacrocycle complex coated on a graphite electrode.

The construction, performance characteristics, and application of a novel polymeric membrane coated on a graphite electrode with unique selectivity towards SCN- are reported. The electrode was prepared by incorporating Ni(II)-2,2,4,9,9,11-hexamethyltetraazacyclotetradecanediene perchlorate into a plasticized poly(vinyl chloride) membrane. The influences of membrane composition, pH and foreign ions were investigated. The electrode displays a near Nernstian slope (-57.8 mV decade-1) over a wide concentration range of 1 x 10(-7)-1 x 10(-1) M of SCN- ion. The electrode has a detection limit of 4.8 x 10(-8) M (2.8 ng/cm3) SCN- and shows response times of about 15 s and 120 s for low to high and high to low concentration sequences, respectively. The proposed sensor shows high selectivity towards SCN- over several common organic and inorganic anions. The electrode revealed a great enhancement in selectivity coefficients and detection limit for SCN-, in comparison with the previously reported electrodes. It was successfully applied to the direct determination of SCN- in milk and biological samples, and as an indicator electrode in titration of Ag+ ions with thiocyanate.     

Zinc(II)-selective sensors based on dibenzo-24-crown-8 in PVC matrix

Membranes of dibenzo-24-crown-8 (I) as an ion active material in poly(vinylchloride) (PVC) based matrix have been tried for zinc(II)-selective sensors. The effect of anion excluder, sodium tetraphenylborate (NaTPB) and plasticizers, tris(2-ethylhexyl)phosphate (TEP), tributylphosphate (TBP), dibutylphthalate (DBP), dibutyl(butyl)phosphonate (DBBP), 1-chloronaphthalene (CN) and dioctylphthalate (DOP) on the performance of the membrane electrodes has also been studied. It was observed that the membrane having the composition (I): PVC:NaTPB:DOP in the ratio 10:200:2:100 gave the best results with a wide working concentration range of 9.2 × 10⁻⁵ to 1.0 × 10⁻¹ M, Nernstian slope of 29.0 ± 0. 5 mV/decade of activity, fast response time of 12 s and good selectivity over a number of mono-, bi-, and trivalent cations. The sensor works well in a pH range 4.8-6.2 and can be employed for the estimation of zinc ions in partially non-aqueous medium having up to 10% (v/v) methanol, ethanol or acetone content. The practical utility of the sensor has been demonstrated by using it successfully as an indicator electrode in the potentiometric titration of Zn²⁺ with EDTA and also for the determination of Zn²⁺ in a real sample analysis of wastewater.     

Ion-selective electrodes for potentiometric determination of ranitidine hydrochloride, applying batch and flow injection analysis techniques.

New ranitidine hydrochloride (RaCl)-selective electrodes of the conventional polymer membrane type are described. They are based on incorporation of ranitidine-tetraphenylborate (Ra-TPB) ion-pair or ranitidine-phosphotungstate (RaPT) ion-associate in a poly(vinyl chloride) (PVC) membrane plasticized with dioctylphthalate (DOP) or dibutylphthalate (DBP). The electrodes are fully characterized in terms of the membrane composition, solution temperature, and pH. The sensors showed fast and stable responses. Nernstian response was found over the concentration range of 2.0 x 10(-5) M to 1.0 x 10(-2) M and 1.0 x 10(-5) M to 1.0 x 10(-2) M in the case of Ra-TPB electrode and over the range of 1.03 x 10(-5) M to 1.00 x 10(-2) M and 1.0 x 10(-5) M to 1.0 x 10(-2) M in the case of Ra-PT electrode for batch and FIA systems, respectively. The electrodes exhibit good selectivity for RaCl with respect to a large number of common ions, sugars, amino acids, and components other than ranitidine hydrochloride of the investigated mixed drugs. The electrodes have been applied to the potentiometric determination of RaCl in pure solutions and in pharmaceutical preparations under batch and flow injection conditions with a lower detection limit of 1.26 x 10(-5) M and 5.62 x 10(-6) M at 25 +/- 1 degrees C. An average recovery of 100.91% and 100.42% with a relative standard deviation of 0.72% and 0.53% has been achieved.     

Thiocyanate ion-selective PVC membrane electrode based on N,N'-ethylene-bis(4-methylsalicylidineiminato)nickel(II).

A highly selective poly(vinyl chloride) (PVC) membrane electrode based on an N,N'-ethylene-bis(4-methyl-salicylidineiminato) nickel(II) [Ni(EBMSI)] complex as a carrier for a thiocyanate-selective electrode is reported. The influences of the membrane composition, pH and possible interfering anions were investigated based on the response properties of the electrode. The electrode exhibited a good Nernstian slope of -58.9 +/- 0.7 mV decade(-1), over a wide pH range of 3.5 - 8.5 and a linear range of 1.0 x 10(-6) - 1.0 x 10(-1) M for thiocyanate. The detection limit of electrode was 3.1 x 10(-7) M SCN(-). The selectivity coefficients determined by a fixed interference method (FIM) indicate that a good discriminating ability towards the SCN- ion compared to other anions. The proposed sensor had a fast response time of about 5 - 15 s and could be used for at least 3 months without any considerable divergence in the potential. It was applied as an indicator electrode in the titration of thiocyanate with Ag+ and in the potentiometric determination of thiocyanate in saliva and urine samples.     

A selective membrane electrode for lanthanum(III) ion based on a hexaaza macrocycle derivative as ionophore.

We have developed a highly La(III)-selective PVC membrane electrode based on a hexaaza macrocycle, 8,16-dimethyl-6,14-diphenyl-2,3,4:10,11,12-dipyridine-1,3,5,9,11,13-hexaazacyclohexadeca-3,5,8,11,13,16-hexaene [Bzo2Me2Pyo2(16)-hexaeneN6] (I) as membrane carrier, dibutylbutyl phosphonate (DBBP) as solvent mediator and sodium tetraphenylborate (NaTPB) as lipophilic additive. The best performance was given by the membrane of macrocycle I having a composition 10:260:5:120 (I:DBBP:NaTPB:PVC). The electrode exhibits a Nernstian response to La(III) ion in the concentration range 1.0x10(-1)-7.94x10(-7) M with a slope of 19.8+/-0.2 mV/decade of concentration and a detection limit of 5.62x10(-7) M. The response time of the sensor is 12 s and it can be used over a period of 4 months with good reproducibility. The electrode works well over a pH range of 2.5-10.0 and in partially non-aqueous medium with up to 30% organic content. The sensor was also used as an indicator electrode in potentiometric titration of La(III) ions with EDTA and for determining La(III) concentration in real samples.     

Glycosylated metalloporphyrins as neutral carriers for PVC membrane electrodes.

In this paper, the synthesis of a novel ionophore, chloro[5,10,15,20-tetrakis[2-(2,3,4,6-tetraacetyl-beta-D-glucopyranosyl)-1-O-phenyl]porphinato]manganese (MnT(o-glu)PPCl), and its application as a neutral carrier for a PVC membrane electrode are described. The MnT(o-glu)PPCl-based PVC membrane electrode shows a potentiometric responses to SCN- over a concentration range of 3.4 x 10(-7) - 1.0 x 10(-1) mol L(-1) with a Nernstian slope and a response time of 20 s. The electrode exhibits an anti-Hofmeister selectivity toward SCN- with respect to common coexisting anions. As active materials, MnT(o-glu)PPCl shows better selectivity toward SCN- than chloro(tetraphenylporphinato)manganese (MnTPPCl). The effect of the electrode membrane compositions has been studied and the experimental conditions were optimized. The electrode was applied to the determination of SCN- in body fluids with satisfactory results.     

A PVC plasticized sensor for Ni(II) ion based on a simple ethylenediamine derivative.

A new PVC membrane ion selective electrode which is highly selective towards Ni(II) ions was constructed using a Schiff base containing a binaphthyl moiety as the ionophore. The sensor exhibited a good Nernstian response for nickel ions over the concentration range 1.0x10(-1)-5.0x10(-6) M with a lower limit of detection of 1.3x10(-6) M. It has a fast response time and can be used for a period of 4 months with a good reproducibility. The sensor is suitable for use in aqueous solutions in a wide pH range of 3.6-7.4 and works satisfactorily in the presence of 25% (v/v) methanol or ethanol. The sensor shows high selectivity to nickel ions over a wide variety of cations. It has been successfully used as an indicator electrode in the potentiometric titration of nickel ions against EDTA and also for the direct determination of nickel content in real samples: effluent samples, chocolates and hydrogenated oils.     

Magnesium-tetrazaporphyrin incorporated PVC matrix as a new material for fabrication of Mg(2+) selective potentiometric sensor

Membrane incorporating [Mg{(TAP)(SBn)₈}] complex, (I), as ionophore with composition I:NaTPB:DOP:PVC in the ratio 10:2:133:200 (w/w) exhibits the best result for potentiometric sensing of Mg²⁺ ions. This gives linear potential response in the concentration range of 9.4×10⁻⁶ to 1.0×10⁻¹ M with a slope of 29.2±0.4 mV per decade of activity of Mg²⁺. Standard deviation in observed values of potentials in this concentration range, from the least square fit line, found to be 2.91 mV with 90% confidence limit lying within ±0.4 mV per decade of activity. The electrode works satisfactorily in the pH range 3.5-7.8 and shows a fast response time of 13±2 s. It shows good selectivity for Mg²⁺ over other mono-, bi- and tri-valent cations. Only K⁺ and Zn²⁺ cause slight interference if present at concentrations ≥1.0×10⁻⁵ M. The electrode is durable and can be used over a period of 5 months with good reproducibility (∼1% error). It has been successfully used as an indicator electrode in potentiometric titration of Mg²⁺ against EDTA as well as for the determination of Mg²⁺ in simulated mixtures.     

Potentiometric membrane electrode for salicylate based on an organotin complex with a salicylal Schiff base of amino acid.

A novel salicylate-selective electrode based on an organotin complex with a salicylal Schiff base of amino acid salicylaldehydeaminoacid-di-n-butyl-Sn(IV) [Sn(IV)-SAADB] as ionophore is described, which exhibits high selectivity for salicylate over many other common anions with an anti-Hofmeister selectivity sequence: Sal- > PhCOO- > SCN- > Cl04- > I- > NO3- > NO2- > Br- > Cl- > CH3COO-. The electrode, based on Sn(IV)-SAADB, with a 30.44 wt% PVC, a 65.45 wt% plasticizer (dioctyl phthalate, DOP), a 3.81 wt% ionophore and a 0.3 wt% anionic additive is linear in 6.0 x 10(-6) - 1.0 x 10(-1) mol l(-1) with a detection limit of 2.0 x 10(-6) mol l(-1) and a slope of 62.0 +/- 1.2 mV/decade of salicylate concentration in a phosphate buffer solution of pH 5.5 at 25 degrees C. The influence on the electrode performances by lipophilic charged additives was studied, and the possible response mechanism was investigated by UV spectra. The electrode was applied to medicine analysis and the result obtained has been satisfactory.     

PVC ion-selective electrodes based on calcium bis-[dialkyl- and di-(4-alkylphenyl) phosphates] and mixed solvent mediators

PVC calcium ion-selective electrodes based on either calcium bis-di(n-decyl)phosphate or calcium bis-di[4-(1,1,3,3-tetramethylbutyl)phenyl]phosphate with various solvent mediators (alone or in pairs) have been evaluated with particular respect to interference from Na(+), K(+), Mg(2+), Sr(2+), Ba(2+), Mn(2+), Cu(2+), Ni(2+) and Zn(2+) ions. PVC calcium ion-selective electrodes based on calcium bis-di[4-(n-octyl)phenyl]phosphate with varied amounts of decan-l-ol plus di-n-octyl phenylphosphonate showed a continuous gradation in selectivity coefficients on going from a high fraction of decan-l-ol to a high fraction of the second mediator. Thus, k(pot)(Ca,Mg) changed from 1.6 for an electrode based exclusively on decan-l-ol to 4.9 x 10(-4) for one based completely on di-n-octyl phenylphosphonate. The corresponding k(pot)(Ca,Na) values were 7.0 x 10(-2) and 1.1 x 10(-3).     

Silver(I) ion-selective membrane based on Schiff base-p-tert-butylcalix[4]arene

A PVC membrane electrode for silver(I) ion based on Schiff base-p-tert-butylcalix[4]arene is reported. The electrode works well over a wide range of concentration (1.0 x 10(-5)-1.0 x 10(-1) mol dm-3) with a Nernstian slope of 59.7 mV per decade. The electrode shows a fast response time of 20 s and operates in the pH range 1.0-5.6. The sensor can be used for more than 6 months without any divergence in the potential. The selectivity of the electrode was studied and it was found that the electrode exhibits good selectivity for silver ion over some alkali, alkaline earth and transition metal ions. The silver ion-selective electrode was used as an indicator electrode for the potentiometric titration of silver ion in solution using a standard solution of sodium chloride; a sharp potential change occurs at the end-point. The applicability of the sensor to silver(I) ion measurement in water samples spiked with silver nitrate is illustrated.     

Novel sulfate ion-selective polymeric membrane electrode based on a derivative of pyrilium perchlorate

A sulfate ion-selective PVC membrane sensor based on 4-(4-bromophenyl)-2,6-diphenylpyrilium perchlorate (BDPP) as a novel sensing material is successfully developed. The electrode shows a good selectivity for sulfate ion with respect to common organic and inorganic anions. The sensor exhibits a good linear response with slope of -28.9+/-0.5 mV per decade over the concentration range of 1.0x10(-6)-1.0x10(-2) M, and a detection limit of 8.0x10(-7) M of SO(4)(2-) ions. The electrode response is independent of pH in the range of 4.0-9.0. The proposed sensor was applied as an indicator electrode in potentiometric titration of sulfate and barium ions, and to the determination of zinc in zinc sulfate tablets.     

Salicylate ion-selective electrode based on new tetranuclear copper complexes of O-vannlin-methionine as neutral carriers.

A new salicylate-selective PVC membrane electrode based on a new Schiff base tetranuclear copper complex of O-vannlin-methionine (Cu(II)(4)-TVM) as a neutral carrier is described. This electrode displays a preferential potentiometric response to salicylate and an anti-Hofmeister selectivity sequence in the following order: Sal(-) > ClO(4)(-) > SCN(-) > I(-) > NO(2)(-) > NO(3)(-) > Br(-) > Cl(-) > SO(3)(2-) > SO(4)(2-) > H(2)PO(4)(-). The electrode exhibits near-Nernstian potential linear range of 1.5 x 10(-6)-1.0 x 10(-1) M with a detection limit of 8.0 x 10(-7) M and a slope of -56.3 mV/decade in pH 3.0-8.0 of phosphorate buffer solution at 20 degrees C. Thanks to the tetranuclear copper(II) in the carrier, the electrode has the advantages of simplicity, fast response, fair stability and reproducibility and low detection limit. The response mechanism to the electrodes is discussed by the a.c. impedance technique and the UV spectroscopy technique. The electrode can be applied to analyses of medicine and the results obtained are in fair agreement with the results given by a standard method.     

Sulfate-selective PVC membrane electrode based on a strontium Schiff's base complex

A strontium Schiff's base complex (SS) can be used as a suitable ionophore to prepare a sulfate-selective PVC-based membrane electrode. The use of oleic acid (OA) and hexadecyltrimethylammonium bromide (HTAB), as additives, and nitrobenzen (NB), dibutyl phthalate (DBP) and benzyl acetate (BA) as solvent mediators, were investigated. The best performance was observed with a membrane composition PVC: NB: SS: HTAB of 30%: 62%: 5%: 3% ratio. The resulting sensor works well over a wide concentration range (1.0 x 10(-2)-1.0 x 10(-6) M) with a Nernstian slope of -29.2 mV per decade of sulfate activity over a pH range 4.0-7.0. The limit of detection of the electrode is 5 x 10(-7) M. The proposed sensor shows excellent discriminating ability toward SO4(2-) ions with regard to many anions. It has a fast response time of about 15 s. The membrane electrode was used to the determination of zinc in zinc sulfate tablets. The sensor was also used as an indicator electrode in the potentiometric titration of SO4(2-) against barium ion.     

A novel ion selective sensor for promethium determination

This is a first promethium(145) ion-selective sensor based on the comparative study of two Schiff base ligands (X(1) and X(2)) as neutral ionophores. Effect of various plasticizers: 2-nitrophenyloctylether (o-NPOE), dibutyl phosphonate (DBP), dioctylphthalate (DOP), tri-(2-ethylhexyl) phosphate (TEHP), dibutyl butylphosphonate (DBBP), chloronaphthalene (CN) and anion excluders: potassium tetrakis (p-chloropheny1) borate (KTpClPB), sodiumtetraphenylborate (NaTPB) and oleic acid (OA) have been studied. The membrane with a composition of ionophore (X(1)/X(2)):KTpClPB:PVC:o-NPOE (w/w, %) in the ratio of 5:5:30:60 exhibited best performance. The best responsive membrane sensors (8 and 21) exhibited working concentration range of 4.5×10(-7)-1.0×10(-2) M and 3.5×10(-6)-1.0×10(-2) M with a detection limits of 3.2×10(-7) M and 2.3×10(-6) M and Nernstian slopes of 20.0±0.5, 19.5±0.5 mV decade(-1) of activity, respectively. The sensor no. 8 works satisfactorily in partially non-aqueous media up to 10% (v/v) content of methanol, ethanol and acetonitrile. Analytical application of the proposed sensor has been demonstrated in determination of promethium (III) ions in spiked water samples.     

Polymeric membrane sensors based on Cd(II) Schiff base complexes for selective iodide determination in environmental and medicinal samples

The two cadmium chelates of schiff bases, N,N'-bis(salicylidene)-1,4-diaminobutane, (Cd-S(1)) and N,N'-bis(salicylidene)-3,4-diaminotoluene (Cd-S(2)), have been synthesized and explored as ionophores for preparing PVC-based membrane sensors selective to iodide(I) ion. Potentiometric investigations indicate high affinity of these receptors for iodide ion. Polyvinyl chloride (PVC)-based membranes of Cd-S(1) and Cd-S(2) using as hexadecyltrimethylammonium bromide (HTAB) cation discriminator and o-nitrophenyloctyl ether (o-NPOE), dibutylphthalate (DBP), acetophenone (AP) and tributylphosphate (TBP) as plasticizing solvent mediators were prepared and investigated as iodide-selective sensors. The best performance was shown by the membrane of composition (w/w) of (Cd-S(1)) (7%):PVC (31%):DBP (60%):HTAB (2%). The sensor works well over a wide concentration range 5.3x10(-7) to 1.0x10(-2)M with Nernstian compliance (59.2mVdecade(-1) of activity) within pH range 2.5-9.0 with a response time of 11s and showed good selectivity for iodide ion over a number of anions. The sensor exhibits adequate life (3 months) with good reproducibility (S.D.+/-0.24mV) and could be used successfully for the determination of iodide content in environmental water samples and mouth wash samples.     

Novel membrane potentiometric sulfate ion sensor based on zinc-phthalocyanine for the quick determination of trace amounts of sulfate.

Poly(vinyl chloride) (PVC) based membranes of zinc-phthalocyanine (ZPC) with hexadecyltrimethylammonium bromide (HTAB) as a cation excluder, and dibutyl phthalate (DBP) and benzyl acetate (BA) as plasticizing solvent mediators were prepared and investigated as a SO4(2-) selective electrode. The best performance was observed with a membrane having a composition of ZPC-PVC-HTAB-BA in a ratio of 5%:32%:3%:60%, which works well over a wide concentration range (1.0 x 10(-2) - 1.0 x 10(-6) M) with a Nemstian slope of -29.2 mV per decade of activity, between the pH values of 2.0 to 7.0. This sensor shows a very fast response time of 10 s, and can be used over a period of 2 months with good reproducibility. The proposed sensor displays excellent selectivity for SO4(2-) over a large number of common inorganic anions. The sensor has been successfully applied for the direct and indirect determination of sulfate and zinc in zinc sulfate tablets, respectively. It was also used as an indicator electrode in the potentiometric titration of sulfate ions with barium ions.