Fällungsanalyse im Mikrogrammbereich: Eine neue Methode

Zusammenfassung Eine neue Methode zur Durchführung gravimetrischer Bestimmungen im Mikrogrammbereich wurde beschrieben; diese beruht im wesentlichen darauf, daß der Niederschlag nicht mehr zusammen mit dem Filter, sondern nach Überführen mit einem geeigneten Lösungsmittel in einem separaten Wägegefäß gewogen wird.Die dazu nötigen Geräte und deren Herstellung wurden beschrieben. Nach dieser Methode wurden folgende Bestimmungen mit zufriedenstellender Richtigkeit durchgeführt: 2,5–25g Al, 5–50g Cu und 5–50g Zn mit Oxin, 2,5–25g Fe(III) und 2,5–25g Ti(IV) mit N-Benzoyl-phenylhydroxylamin, 5–50g Ni und 5–50g Cu mit Salicylaldoxim, 2,5–50g Co(II) und 2,5–50g Fe(III) mit -Nitroso--naphthol sowie 5–50g Chlorid als Silberchlorid.

---

Precipitation analysis in the microgram-scale: A new method

Summary A new method for gravimetric determinations in the microgram-scale is described. This method is based on the fact that the precipitate is not weighed together with the filter but is transferred to a separate weighingvessel using a suitable solvent. The necessary simple devices and their use are described. The following determinations were carried out with satisfying accuracy: 2,5–25g Al, 5–50g Cu and 5–50g Zn with Oxine, 2,5–25g Fe and 2,5–25g Ti withN-benzoylphenylhydroxylamine, 5–50g Ni and 5–50g Cu with salicylaldoxime, 2,52–50g Co and 2,5–50g Fe with -nitroso--naphthol and 5–50g chloride as silver chloride.

     

Effect of Surfactants on the Immobilization of 4-(2-Pyridylazo)resorcinol on Silochroms

The effect of cationic surfactants (cetyltrimethylammonium bromide, cetylpyridinium bromide, and tetrabutylammonium perchlorate) and a nonionic surfactant (OP-7) on the conditions of the immobilization of 4-(2-pyridylazo)resorcinol (PAR) on three types of silica gel (Silochrom S-120 (200–350 m), Silochrom S-120 (315–500 m), and Silochrom S-80 (200–350 m)) was studied. It was found that OP-7 does not affect the adsorption of surfactants. The effect of cationic surfactants increases in the order tetrabutylammonium perchlorate < cetyltrimethylammonium bromide < cetylpyridinium bromide. The adsorption activity of silica gels increases in the order Silochrom S-120 (315–500 m) < Silochrom S-80 (200–350 m) < Silochrom S-120 (200–350 m). Cetylpyridinium bromide provides full immobilization of PAR on silica gel Silochrom S-120 (200–350 m) in the pH range 2–9.     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

Nickel(II) xanthates with nitrogen heterocycles as bridging ligands

New homopolynuclear nickel(II) xanthate complexes with nitrogen donor heterocycles as bridging ligands have been prepared, namely [Ni(Rxa)2(-L)]n and [Ni2(Rxa)4(-L1)], where R=i-Pr,i-Am; xa=OCS2– L=1,2-bis(4- pyridyl)ethane (bpe), 4,4-dithiodipyridyl (dtp), 1,2-bis(4- pyridyl)ethylene (dpe), 4,4-trimethylene-dipyridine (tmd); L1=2,3-bis(2-pyridyl)pyrazine (bpp), 2,4-bis(5,6- diphenyl-1,2,4-triazine-3-yl)pyridine (bdt), or 2,4,6-tris(2- pyridyl)-1,3,5-triazine (tpt). The compounds have been characterized by elemental analyses, i.r. and electronic spectroscopies, magnetochemical and conductivity measurements. The results show that the [Ni(Rxa)2(-L)]n complexes are linear polymers in which the nitrogen heterocycles bridge between the nickel(II) ions, which are coordinated by four sulfur and two nitrogen atoms and have trans-octahedral geometry. The nearly constant values of the effective magnetic moment (3.36–3.34 eff/B) over the 77–295 K temperature range indicate that exchange interactions are lacking among the paramagnetic centres in the linear structure, [Ni(i-Amxa)2(dpe)]n. The variable- temperature magnetic susceptibilities of the [Ni2(i-Prxa)4(bpp)] (3.00–2.95eff/B per Ni atom), [Ni2(i-Prxa)4(bdt)] (2.72–2.63 eff/B per Ni atom), and [Ni2(i-Amxa)4(tpt)] (2.76–1.87 eff/B per Ni atom) were measured down to liquid nitrogen temperature. In the case of binuclear nickel(II) complexes with bdt or tpt, antiferromagnetic coupling between the nickel(II) ions was detected, giving the exchange integral J=–4.0cm–1 and –29.6cm–1, respectively.     

Spectrofluorimetric determination of nucleic acids as 8-hydroxyquinoline/ yttrium ternary complexes

The formation of nucleic acids/8-hydroxyquinoline/yttrium(III) ternary complexes and their fluorescent properties have been studied. The nucleic acids studied include native and thermally denatured calf thymus DNA, fish sperm DNA and yeast RNA. In the range of pH 7.6–8.5, controlled by NH₃-NH₄C1 buffer, ternary complexes are formed that fluoresce at different wavelengths with different nucleic acids. Based on the fluorescence reactions, sensitive spectrofluorimetric methods for nucleic acids are proposed. In optimal conditions, the calibration curves were linear in the range 0.5–4.0 gml^–1 for calf thymus DNA, 0.5–2.5 g ml^–1 for fish sperm DNA and 0.5–4.0 g ml^–1 for yeast RNA. The limits of determination (3 ) were 0.030 g ml^–1 for calf thymus DNA, 0.020 g ml^–1 for fish sperm DNA and 0.090 g ml^–1 for yeast RNA. Corresponding to the interferences of coexisting substances, six synthetic samples were constructed and the results of determination were satisfactory.     

Zur Bestimmung N-substituierter Aniline mit Natriumchlorit

Zusammenfassung Es wird eine photometrische Bestimmungsmethode beschrieben für Anilin (40–720 g/ml), Monoäthylanilin (90–1650 g/ml) und Diäthylanilin (100–1600 g/ml) mit Natriumchlorit in äthanolisch-wäßrigen Lösungen, sowie für Diäthylanilin (85–1140 g/ml) und Dimethylanilin (30–330 g/ml) neben den primären und sekundären Aminen in essigsaurer Lösung mit demselben Reagens. Das Verfahren liefert gute Ergebnisse.

---

Summary A photometric procedure is described for the determination of aniline (40–720 g/ml), monoethylaniline (90–1650 g/ml), and diethylaniline (100–1600 g/ml) with sodium chlorite in aqueous ethanolic solutions and of diethylaniline (85–1140 g/ml) and dimethylamline (30 to 330 g/ml) in presence of the primary and secondary amines in acetic acid solution using the same reagent. Good results have been obtained,

     

Nuclear interferences of uranium and thorium in a reactor neutron activation analysis determination of cerium using the radionuclides141Ce and143Ce

The interference contributions of uranium and thorium to the determination of cerium based on radionuclides¹⁴¹Ce and¹⁴³Ce produced by irradiation in a reactor core was determined. The values of the interference contributions for¹⁴¹Ce were 0.28±0.01 g Ce/g U and /2.01±0.05/x10^–3 g Ce/g Th, and for¹⁴³Ce 1.33±0.03 g Ce/g U and /9.0±0.2/x10^–3 g Ce/g Th.     

Trace and minor elements in four commercial honey brands

Instrumental neutron activation analysis was used to measure the concentrations of 24 elements in four honey brands commercially available in Austin, Texas (USA). The measured elements (and concentration) were: As, (<30 ng/g); Ba, (<2 g/g); Br, (0.24–0.49 g/g); Ce, (<20 ng/g); Co, (9–180 ng/g); Cr, (37–64 ng/g); Cs, (<3–45 ng/g); Fe, (<4–15.9 g/g); Hf, (<3 ng/g); Hg, (1 ng/g); K, (91–230 g/g); La, (<4 ng/g); Na, (20.3–25.3 g/g); Ni, (0.39–0.77 g/g); Rb, (68–340 ng/g); Sb, (13–61 ng/g); Sc, (<0.3–200 ng/g); Se, (<20 ng/g); Sm, (<9 ng/g); Sr, (<2 ng/g); Th, (<4 ng/g); U, (<30 ng/g); Zn, (3.36–4.61 g/g); and Zr, (<0.5–0.84 g/g). The results obtained were compared to the concentration of the same elements in honey produced or commercially available in Turkey, Mexico, El-Salvador, China, Czechoslovakia and Yugoslavia.     

Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

A toxic reagent-free method for normal-phase matrix solid-phase dispersion extraction and reversed-phase liquid chromatographic determination of aldrin,dieldrin, and DDTs in animal fats

A method for the determination of aldrin, dieldrin, DDT, DDE, and DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic reagents is developed, that uses high-performance liquid chromatography after the sample has been prepared by matrix solid-phase dispersion (MSPD) with acidic alumina oxide. A reversed-phase C₁-silica column with a mobile phase of 50% (v/v) ethanol solution (in water) and a photo-diode array detector were used for the determination. Average recoveries of the target compounds (0.2–5.0 g g^–1) ranged from 84–98%, with coefficients of variation of <5%. The limits of quantitation were 0.16 g g^–1 for AD, 0.10 g g^–1 for DD, 0.06 g g^–1 for DDT, 0.07 g g^–1 for DDE, and 0.05 g g^–1 for DDD. No toxic reagents were used at all.     

Platinum concentration in silicone breast implant material and capsular tissue by ICP-MS

Inductively coupled plasma-mass spectrometry (ICP-MS) was used to determine the concentration of platinum (Pt) in silicone breast implant gel (range, 0.26–48.90 g g^–1 Pt; n=15), elastomer (range, 3.05–28.78 g g^–1 Pt; n=7), double lumen (range, 5.79–125.27 g g^–1 Pt; n=7), foam (range, 5.79–8.36 g g^–1 Pt; n=2), and capsular tissue (range, 0.003–0.272 g g^–1 Pt; n=15). The results show that very high levels of Pt are present in the encasing elastomer, double lumen, and foam envelope materials. Silicone breast implants can be a source of significant Pt exposure for individuals with these implants.     

Simultaneous determination of copper,mercury and lead by first-order derivative spectrophotometry using dithizone as reagent

A first-order derivative spectrophotometric method has been developed for the simultaneous determination of copper, mercury and lead at g/L levels using dithizone as reagent. The procedure involves the simultaneous extraction of these elements by dithizone in chloroform from weakly alkaline solutions. Linear calibration curves were obtained in the ranges 0.5–10 (Cu), 1–10 (Hg) and 1–10 (Pb) g present in 40 ml of aqueous phase with detection limits of 5 g/L (Cu) and 20 g/L (Hg and Pb). The R.S.D.s for 100 g/L of copper, mercury and lead were 2.5, 2.6 and 3.1% respectively, for 5 determinations. The method is applicable for the determination of copper and lead in marine sediment samples with good precision and accuracy.     

Glycosides of marine invertebrates. X. The structure of stichoposides A and B from the holothurianStichopus cloronotus

The structures of two triterpene oligosides from the holothurianStichopus cloronotus (Brandt) have been established; they are: 23-acetoxy-3-[O--D-quinovopyranosyl-(12)--D-xylopyranosyloxy]holost-7(8)-ene and 23-acetoxy-3-[O--D-glucopyranosyl-(12)--D-xylopyranosyloxy]holost-7(8)-ene.Pacific Ocean Institute of Bioorganic Chemistry, Far Eastern Scientific Center, Academy of Sciences of the USSR, Vladivostok. Translated from Khimiya Prirodnykh Soedinenii, No. 2, pp. 181–184, March–April, 1981.     

Determination of traces of sodium alkylbenzenesulphonate by high-performance liquid chromatography. Application to water

Summary For the trace determination of sodium alkylbenzenesulphonate (ABS) by HPLC the following conditions were employed: Shimadzu ZORBAX SIL Column (5 m, 4.6 mm i.d. x 150 mm) as stationary phase, 0.2% ammoniaethanol (v/v) as mobile phase, UV detector at 225 nm, injection volume 12 l. The chromatograms of ABS were simple and sharp (detection limit of ABS 0.02 g in 12 l of ethanol). The calibration curves of ABS were linear in a concentration range of 0.03 0.3 g in 12 l of ethanol. In the case of linear sodium dodecylbenzenesulphonate positive errors of 1 4% were caused by non-ionic surfactants or laurylsulphate (6 times excess), 10 50% positive errors were caused by 2 6 times excess of household detergents.Standard water samples containing ABS were treated with a weak base anion-exchange resin, the adsorbed ABS were eluted, and then determined either by HPLC or by the methylene blue spectrophotometric method. Recoveries of ABS in water were about 92 107% by HPLC.

---

Bestimmung von Spuren Natriumalkylbenzolsulfonat mit Hilfe der HPLC. Anwendung auf Wasser

Zusammenfassung Für die Spurenbestimmung von Natriumalkylbenzolsulfonat (ABS) durch HPLC werden die folgenden Bedingungen empfohlen:Shimadzu ZORBAX SIL (5 m, 4,6 mm x 150 mm) als stationäre Phase, 0,2% Ammoniak/Ethanol als mobile Phase, UV-Detektor bei 225 nm, Injektionsvolumen 12 l. Die erhaltenen Chromatogramme sind einfach und scharf (Nachweisgrenze 0,02 g in 12 ml Ethanol). Die Eichkurven sind im Konzentrationsbereich von 0,03–0,3 g in 12 l Ethanol linear. Im Falle des linearen Natriumdodecylbenzolsulfonats werden bei Anwesenheit von nicht-ionischen oberflächenaktiven Substanzen oder von Laurylsulfat in 6fachem Überschuß positiver Fehler von 1–4% erhalten; bei 2–6fachem Überschuß von Haushaltswaschmitteln ergeben sich positive Fehler von 10–50%.Standard-Wasserproben werden zunächst einer Behandlung mit einem Anionenaustauscher unterzogen, die adsorbierten ABS eluiert und durch HPLC oder nach der Methylenblaumethode analysiert. Wiederfindungsraten liegen bei 92–107%.

     

Determination of nitrogen in uranium and uranium-oxide by high-temperature gas-extraction

Summary The reducing fusion gas extraction method has been used for the determination of nitrogen in uranium metal and uranium dioxide reference materials at levels of about 10–15g·g^–1. It has been found that when extracting at temperatures above 2700° C the use of a platinum flux is no longer necessary. Pure nitrogen and nitrogen-helium mixtures were used for calibrating the detection unit in the range of 1.5–670 g. The calibration of the extraction was performed with metallic reference materials in the range of 8–331 g N₂ content.

---

Bestimmung von Stickstoff in Uran und Uranoxid durch Hochtemperatur-Gasextraktion

Zusammenfassung Die Gasextraktion aus reduzierender Schmelze wurde zur Stickstoffbestimmung in Uranmetall- und Urandioxid-Referenzmaterialien bei Gehalten von 10–15 g·g^–1 angewendet. Bei Temperaturen über 2700° C ist kein Platinbad mehr erforderlich. Zur Eichung der Detektionseinheit im Bereich von 1,5–670 g wurden reiner Stickstoff oder Stickstoff-Helium-Mischungen benutzt. Zur Eichung der Extraktion wurden metallische Referenzmaterialien mit (8–331g) N₂ eingesetzt.

     

Propane aromatization over Pt?Sn/ZSM-5 catalysts

Addition of Sn modifies the catalytic performance of Pt/ZSM-5. Total conversions decrease with increasing Sn/Pt ratio. Selectivity to aromatics is higher on the Pt–Sn samples. A Pt–Sn interaction has been confirmed by H₂ chemisorption and TPR experiments.

---

Sn Pt/ZSM5. Sn/Pt . Pt–Sn. Pt–Sn H₂ .

     

Determination of some trace elements in high-purity aluminium, zinc and commercial steel by AAS after preconcentration on amberlite XAD-1180 resin

The determination of trace metals, e.g. Bi, Cd, Pb, in high-purity aluminium, zinc and commercial steel by flame or graphite furnace atomic absorption spectrometry following their preconcentrations as iodo complexes on XAD-1180 resin by means of a short column system is described. The recoveries are quantitative (95%). The relative standard deviations varies between 6% and 10%. The relative errors are less than 8% in a concentration range of 1 × 10^–3 –4 × 10^–5%. Detection limits for flame AAS and GFAAS were in the ranges of 0.002–0.110 g/ml and 0.0003–0.004 g/ml or in the ranges of 0.08–4.40 g/g and 0.012–0.16 g/g with respect to the solid samples, respectively.     

Preparation and Properties of Nb-Coated Barium Titanate Composite Particles by Surface Modification with Nb Alkoxide in Hydrophobic Solvent

Chemical processing for the preparation of Nb-coated barium titanate composite particles was investigated using surface modification technology, hydrolyzing Nb ethoxide on the surface of barium titanate particles dispersed in hydrophobic solvent.It was confirmed from the measurements of specific surface area and zeta potential as well as SEM, TEM and EDX observations of the resulting composite particles that the original barium titanate particles were coated uniformly with hydrolysis product of Nb ethoxide.Barium titanates coated with 1 wt% of Nb as oxide were well sintered at 1200–1300°C. The dielectric constants of the sintered barium titanates showed flattened temperature dependence, but it depended upon the average particle size of original barium titanate. The sintered bodies of Nb-coated barium titanate powders with average particle size of 0.2 m gave dielectric constants of 2000–3000 and those of barium titanate with average particle size of 0.5 m showed dielectric constants of 3000–4000 at room temperature.The microstructure of the sintered barium titanate coated with Nb oxide consisted of grains of about 1 m, smaller than those of sintered original barium titanate.     

Colorimetric determination of vanadium with 5,7-dibromo-8-hydroxyquinoline after paper-chromatographic separation from interfering ions

Summary 5,7-Dibromo-8-hydroxyquinoline is recommended as reagent for the colorimetric determination of vanadium. The absorption is measured at 394 nm. Interfering ions are removed by paper chromatography with a collidine containing solvent. With amounts of 45–120 g of vanadium an error of ± 1 g has been obtained.

---

Zusammenfassung Zur colorimetrischen Vanadiumbestimmung wird 5,7-Dibrom-8-hydroxychinolin als Reagens empfohlen. Die Messung erfolgt bei 394 nm. Störende Ionen werden durch Papier-Chromatographie mit einem collidinhaltigen Fliemittel entfernt. Der Fehler betrug ±1 g bei Vanadiummengen von 45–120g.